REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET REV STATUS REV OF SHEETS SHEET PMIC N/A PREPARED BY Steve Duncan STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A 1 2 3 4 5 7 8 9 10 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 CHECKED BY Greg Cecil APPROVED BY Raymond Monnin 6 http://www.dscc.dla.mil MICROCIRCUIT, HYBRID, LINEAR, 5.2VOLT, SINGLE CHANNEL, DC-DC CONVERTER DRAWING APPROVAL DATE 02-04-10 REVISION LEVEL SIZE A SHEET CAGE CODE 5962-02513 67268 1 OF DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 10 5962-E276-02 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 02513 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) X Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 Generic number Circuit function MSA285R2S/883 DC-DC converter, 5 W, +5.2 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter X Descriptive designator See figure 1 Terminals Package style 8 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range.................................................................... Power dissipation (PD)............................................................... Output power ............................................................................. Lead soldering temperature (10 seconds)................................. Storage temperature range ....................................................... -0.5 V dc to +50 V dc 2.2 W 5.2 W +300°C -65°C to +150°C 1.4 Recommended operating conditions. Input voltage range ..................................................................... Case operating temperature range (TC)...................................... +16 V dc to +40 V dc -55°C to +125°C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbook are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 3 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 4 TABLE I. Electrical performance characteristics. Test Output voltage Symbol VOUT Conditions -55°C ≤ TC ≤ +125°C VIN = 28 V dc ±0.5 V, CL = 0 unless otherwise specified Group A subgroups Limits Device type Min IOUT = 962 mA 1 01 2,3 Unit Max 5.15 5.25 4.99 5.41 V dc Output current IOUT VIN = 16 V dc to 40 V dc 1,2,3 01 962 mA VOUT ripple voltage VRIP IOUT = 962 mA, BW = 10 kHz to 2 MHz 1 01 335 mVp-p 2,3 520 VOUT line regulation VRLINE VIN =16 V dc to 40 V dc, IOUT = 962 mA 1,2,3 01 50 mV VOUT load regulation VRLOAD IOUT = 0 to 962 mA 1,2,3 01 50 mV Input current IIN IOUT = 0 A, Inhibit (pin 5) = 0 1,2,3 01 4 mA IOUT = 0 A, Inhibit (pin 5) = open 1, 2, 3 01 40 1 01 100 IIN ripple current IRIP IOUT = 962 mA, BW = 10 kHz to 10 MHz 150 2,3 Efficiency Eff IOUT = 962 mA 1 mAp-p 01 66 2,3 % 64 Isolation ISO Input to output or any pin to case except the case ground (pin 8) at 500V dc, TC = +25°C 1 01 100 Capacitive load 1/ 2/ CL No effect on dc performance, TC = +25°C 4 01 300 µF Short circuit power dissipation PD Short circuit 1 01 2 W 2,3 Switching frequency FS IOUT = 962 mA 4 2.2 01 5,6 VOUT step load transient 3/ VTLOAD 50% load to/from 100% load 4 5,6 MΩ 01 450 600 400 660 -250 +250 -750 +750 kHz mV pk See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 5 TABLE I. Electrical performance characteristics - Continued Test Conditions Symbol Group A subgroups -55°C ≤ TC ≤ +125°C VIN = 28 V dc ±0.5 V, CL = 0 unless otherwise specified VOUT step load transient recovery 3/ 4/ TTLOAD Device type Min 50% load to/from 100% load 4 Unit Limits 01 Max µs 250 5,6 1500 VOUT step line transient 2/ 5/ VTLINE Input step 16 V dc to/from 40 V dc, IOUT = 962 mA 4,5,6 01 -500 +500 mV pk VOUT step line transient recovery 2/ 4/ 5/ TTLINE Input step 16 V dc to 40 V dc, IOUT = 962 mA 4,5,6 01 500 µs Input step 40 V dc to 16 V dc, IOUT = 962 mA 4,5,6 01 900 µs mV pk Start up overshoot 2/ VtonOS IOUT = 962 mA 4,5,6 01 200 Start up delay 6/ TonD IOUT = 962 mA 4,5,6 01 75 ms Load fault recovery 2/ TrLF IOUT = 962 mA 4,5,6 01 75 ms 1/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. 2/ Parameter shall be tested as part of device characterization and after design and process changes. Thereafter, parameters shall be guaranteed to the limits specified in table I. 3/ Load step transition time greater than 10 microseconds. 4/ Recovery time is measured from the initiation of the transient until VOUT has returned to within ±1 percent of VOUT final value. 5/ Input step transition time greater than 10 microseconds. 6/ Start up delay time measurement is either for a step application of power at the input or the removal of a ground signal from the inhibit pin (pin 5) while power is applied to the input. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 6 Case outline X. Symbol A b b1 D/E E1 e/S e1 e2 e3 e4/S1 L R Millimeters Min Max 6.86 1.78 DIA 0.64 DIA 27.31 20.19 20.45 3.23 3.48 8.31 8.56 13.39 13.64 18.47 18.72 23.55 23.80 5.59 1.14 1.40 Inches Min Max .270 .070 DIA .025 DIA 1.075 .795 .805 .127 .137 .327 .337 .527 .537 .727 .737 .927 .937 .220 .045 .055 NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are for reference only. 3. Case outline X weight: 15 grams maximum. FIGURE 1. Case outline(s). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 7 Device type 01 Case outline X Terminal number Terminal symbol 1 Output 2 Output return 3 No connection 4 No connection 5 Inhibit 6 Input 7 Input return 8 Case ground FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 8 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical parameters 1 Not applicable End-point electrical parameters for Radiation Hardness Assurance (RHA) devices * PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 9 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614) 692-0514. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-02513 A REVISION LEVEL SHEET 10 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 02-04-10 Approved sources of supply for SMD 5962-02513 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. Standard microcircuit drawing PIN 1/ 5962-0251301HXA 5962-0251301HXC Vendor CAGE number 50821 50821 Vendor similar PIN 2/ MSA285R2S/883 MSA285R2S/883 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 50821 Vendor name and address Interpoint Corporation 10301 Willows Road Redmond, WA 98073-9705 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.