74LVQ163 SYNCHRONOUS PRESETTABLE 4-BIT COUNTER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: fMAX = 180 MHz (TYP.) at VCC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.3V (TYP.) at VCC = 3.3V 75Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0 V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 163 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74LVQ163 is a low voltage CMOS SYNCHRONOUS PRESETTABLE COUNTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and low noise 3.3V applications. It is a 4 bit binary counter with Synchronous Clear. The circuit have four fundamental modes of operation, in order of preference: synchronous reset, parallel load, count-up and hold. Four SOP TSSOP ORDER CODES PACKAGE TUBE T&R SOP TSSOP 74LVQ163M 74LVQ163MTR 74LVQ163TTR control inputs, Master Reset (CLEAR), Parallel Enable Input (LOAD), Count Enable Input (PE) and Count Enable Carry Input (TE), determine the mode of operation as shown in the Truth Table. A LOW signal on CLEAR overrides counting and parallel loading and allows all outputs to go LOW on the next rising edge of CLOCK. A LOW signal on LOAD overrides counting and allows information on Parallel Data Qn inputs to be loaded into the flip-flops on the next rising edge of CLOCK. With LOAD and CLEAR, PE and TE permit counting when both are high. Conversely, a LOW signal on either PE and TE inhibits counting. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/13 74LVQ163 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 CLEAR 2 CLOCK 3, 4, 5, 6 7 10 9 14, 13, 12, 11 15 8 16 A, B, C, D PE TE LOAD QA to QD NAME AND FUNCTION Synchronous Master Reset Clock Input (Positive Edge Trigger) Data Inputs Count Enable Input Count Enable Carry Input Parallel Enable Input Flip-Flop Outputs CARRY OUT Terminal Count Output GND Ground (0V) Positive Supply Voltage VCC TRUTH TABLE INPUTS OUTPUTS FUNCTION CLEAR LOAD PE TE L X X X L L L L RESET TO "0" H L X X A B C D PRESET DATA H H X L NO CHANGE NO COUNT H H L X NO CHANGE NO COUNT H H H H COUNT UP COUNT H X X X NO CHANGE NO COUNT CK X : Don’t Care; A, B, C, D; Logic level of data input; CARRY OUT : TE x QA x QB x QC x QD 2/13 74LVQ163 LOGIC DIAGRAM 3/13 74LVQ163 TIMING CHART ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage VI DC Input Voltage VO DC Output Voltage Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 50 mA ± 300 mA ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 4/13 74LVQ163 RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Value Unit Supply Voltage (note 1) 2 to 3.6 V VI Input Voltage 0 to VCC V VO Output Voltage Top Operating Temperature dt/dv Input Rise and Fall Time VCC = 3.0V (note 2) 0 to VCC V -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage TA = 25°C VCC (V) Min. Typ. Max. 2.0 3.0 to 3.6 3.0 Value Low Level Output Voltage 3.0 -55 to 125°C Min. Min. 0.8 IO=-50 µA 2.9 IO=-12 mA 2.58 2.99 2.9 2.9 2.48 2.2 ICC IOLD IOHD Input Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) V 0.8 2.48 Unit Max. 2.0 0.8 V V 2.2 IO=50 µA 0.002 0.1 0.1 0.1 IO=12 mA 0 0.36 0.44 0.44 0.55 0.55 IO=24 mA II Max. 2.0 IO=-24 mA VOL -40 to 85°C V 3.6 VI = VCC or GND ± 0.1 ±1 ±1 µA 3.6 VI = VCC or GND 4 40 40 µA 3.6 VOLD = 0.8 V max 36 25 mA VOHD = 2 V min -25 -25 mA 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 75Ω 5/13 74LVQ163 DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) Value TA = 25°C VCC (V) Min. 3.3 -0.8 3.3 Typ. Max. 0.3 0.8 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. V -0.3 2 V CL = 50 pF 3.3 0.8 V 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. 6/13 74LVQ163 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time CK to Q tPLH tPHL Propagation Delay Time CK to CARRY OUT tPLH tPHL Propagation Delay Time TE to CARRY OUT tW CK pulse Width, (Count) High or LOW tW CK pulse Width, (Load) High or LOW ts Setup Time HIGH or LOW (INPUT to CLOCK) th Hold Time HIGH or LOW (INPUT to CLOCK) ts Setup Time HIGH or LOW (CLEAR to CLOCK) th Hold Time HIGH or LOW (CLEAR to CLOCK) ts Setup Time HIGH or LOW (LOAD to CLOCK) th Hold Time HIGH or LOW (LOAD to CLOCK) ts Setup Time HIGH or LOW (PE or TE to CLOCK) th Hold Time HIGH or LOW (PE or TE to CLOCK) fMAX Maximum Clock Frequency tOSLH tOSHL Output To Output Skew Time (note1, 2) VCC (V) Value TA = 25°C Min. 2.7 Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. Max. 7.5 12.0 15.0 17.0 3.3 2.7 6.3 9.5 11.0 12.5 8.8 14.0 16.0 18.5 3.3(*) 7.1 10.5 12.0 14.0 2.7 6.1 10.0 11.5 13.0 3.3(*) 5.2 8.0 9.5 10.5 (*) 2.7 4.0 1.9 4.0 4.0 3.0 1.9 3.0 3.0 2.7 4.0 1.9 4.0 4.0 3.3(*) 3.0 1.9 3.0 3.0 2.7 5.0 2.5 5.0 5.0 4.0 2.1 4.0 4.0 1 -1.6 1 1 0.5 -1.2 0.5 0.5 2.7 3.0 1.5 3.0 3.0 3.3(*) 2.5 1.2 2.5 2.5 3.3 3.3 (*) (*) 2.7 3.3 (*) 2.7 1 -0.6 1 1 3.3(*) 0.5 -0.5 0.5 0.5 2.7 8.0 3.7 8.0 8.0 3.3(*) 6.0 3.2 6.0 6.0 2.7 0 -3.0 0 0 0 -2.5 0 0 2.7 7.0 3.4 7.0 7.0 3.3(*) 6.0 3.0 6.0 6.0 2.7 0 -2.6 0 0 0 -2.2 0 0 100 150 80 60 120 180 100 80 3.3 3.3 (*) (*) 2.7 (*) 3.3 2.7 3.3 (*) 0.5 0.5 1.0 1.0 1.0 1.0 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns MHz 1.0 1.0 ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, t OSHL = |tPHLm - t PHLn|) 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V 7/13 74LVQ163 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter TA = 25°C VCC (V) CIN Input Capacitance 3.3 CPD Power Dissipation Capacitance (note 1) 3.3 Value Min. fIN = 10MHz Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. 4 pF 33 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x f IN + ICC/n (per circuit) TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RL = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 : PROPAGATION DELAYS , COUNT MODE (f=1MHz; 50% duty cycle) 8/13 74LVQ163 WAVEFORM 2: PROPAGATION DELAYS CLEAR MODE (f=1MHz; 50% duty cycle) WAVEFORM 3: PROPAGATION DELAYS PRESET MODE (f=1MHz; 50% duty cycle) 9/13 74LVQ163 WAVEFORM 4: PROPAGATION DELAYS COUNTABLE MODE (f=1MHz; 50% duty cycle) WAVEFORM 5: PROPAGATION DELAYS CASCADE MODE (f=1MHz; 50% duty cycle) 10/13 74LVQ163 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) PO13H 11/13 74LVQ163 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 12/13 74LVQ163 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 13/13