3.5x2.8 mm SMD CHIP LED LAMP PRELIMINARY SPEC Part Number: AA3529QB24ZS BLUE ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features z SINGLE Description COLOR. z SUITABLE The Blue source color devices are made with InGaAlN FOR ALL SMT ASSEMBLY AND SOLDER z AVAILABLE z IDEAL z LOW ON TAPE AND REEL. SMD PACKAGE, SILICONE RESIN. THERMAL RESISTANCE. z PACKAGE: 1500PCS / REEL. z MOISTURE SENSITIVITY LEVEL : LEVEL 4. z RoHS It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. FOR BACKLIGHTING. z WHITE Vertical Light Emitting Diode. Static electricity and surge damage the LEDS. PROCESS. All devices, equipment and machinery must be electrically grounded. COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or damage the internal circuitry. 1. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134 Selection Guide Dice Part No. AA3529QB24ZS Iv (mcd) [2] @ 150mA Lens Type BLUE (InGaAlN) WATER CLEAR Φv (mlm) [2] @ 150mA Viewing Angle [1] Min. Typ. Min. Typ. 2 θ 1/2 1200 1500 5500 7000 120 ° Notes: 1.θ 1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2.Luminous Intensity/ Luminous Flux: +/-15% Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λ peak Peak Wavelength Blue λ D[1] Dominant Wavelength Δλ 1/2 Typ. Max. Units Test Conditions 450 nm IF=150mA Blue 457 nm IF=150mA Spectral Line Half-width Blue 20 nm IF=150mA C Capacitance Blue 110 pF VF=0V;f=1MHz VF[2] Forward Voltage Blue 3.5 V IF=150mA 3.9 Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Blue Units Power dissipation 585 mW DC Forward Current 150 mA Thermal Resistance 140 °C/W Operating/Storage Temperature -40°C To +85°C SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134 BLUE AA3529QB24ZS SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134 AA3529QB24ZS Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134 PACKING & LABEL SPECIFICATIONS AA3529QB24ZS SPEC NO: DSAH9589 REV NO: V.1 DATE: DEC/06/2007 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.Chen ERP: 1201003134