TI ADS8548SRGCR

ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
12-, 14-, 16-Bit, Eight-Channel, Simultaneous Sampling
ANALOG-TO-DIGITAL CONVERTERS
Check for Samples: ADS8528, ADS8548, ADS8568
FEATURES
DESCRIPTION
•
The ADS8528/48/68 contain eight low-power, 12-,
14-, or 16-bit, successive approximation register
(SAR)-based analog-to-digital converters (ADCs) with
true bipolar inputs. These channels are grouped in
four pairs, thus allowing simultaneous high-speed
signal acquisition of up to 650kSPS.
1
2
•
•
•
•
•
•
Family of 12-, 14-, 16-Bit, Pin- and
Software-Compatible ADCs
Maximum Data Rate Per Channel:
– ADS8528: 650kSPS (PAR) or
480kSPS (SER)
– ADS8548: 600kSPS (PAR) or
450kSPS (SER)
– ADS8568: 510kSPS (PAR) or
400kSPS (SER)
Excellent AC Performance:
– Signal-to-Noise Ratio:
ADS8528: 73.9dB
ADS8548: 85dB
ADS8568: 91.5dB
– Total Harmonic Distortion:
ADS8528: –89dB
ADS8548: –91dB
ADS8568: –94dB
Programmable and Buffered Internal
Reference: 0.5V to 2.5V or 0.5V to 3.0V
Supports Input Voltage Ranges of Up to ±12V
Selectable Parallel or Serial Interface
Scalable Low-Power Operation Using
Auto-Sleep Mode: Only 32mW at 10kSPS
Fully Specified Over the Extended Industrial
Temperature Range
The devices support selectable parallel or serial
interface
with
daisy-chain
capability.
The
programmable reference allows handling of analog
input signals with amplitudes up to ±12V.
The ADS8528/48/68 family supports an auto-sleep
mode for minimum power dissipation and is available
in both QFN-64 and LQFP-64 packages. The entire
family is specified over a temperature range of –40°C
to +125°C.
Clock
Generator
CH_A0
SAR ADC
CH_A1
SAR ADC
CH_B0
SAR ADC
CH_B1
SAR ADC
Control
Logic
Control
Signal
Bus
Config
Register
CH_C0
SAR ADC
CH_C1
SAR ADC
CH_D0
SAR ADC
CH_D1
SAR ADC
REFIO
String DAC
APPLICATIONS
•
•
•
•
•
Protection Relays
Power Quality Measurement
Multi-Axis Motor Control
Programmable Logic Controllers
Industrial Data Acquisition
I/O
Parallel
or Serial
Data Bus
2.5/3V
Reference
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
FAMILY/ORDERING INFORMATION (1)
(1)
PRODUCT
RESOLUTION
(Bits)
MAXIMUM DATA RATE:
PAR/SER
(kSPS/ch)
SNR
(dB, typ)
THD
(dB, typ)
ADS8528
12
650/480
73.9
–89
ADS8548
14
600/450
85
–91
ADS8568
16
510/400
91.5
–94
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
Supply voltage
VALUE
UNIT
HVDD to AGND
–0.3 to 18
V
HVSS to AGND
–18 to 0.3
V
AVDD to AGND
–0.3 to 6
V
–0.3 to 6
V
Analog input voltage
HVSS – 0.3 to HVDD + 0.3
V
Reference input voltage with respect to AGND
AGND – 0.3 to AVDD + 0.3
V
Digital input voltage with respect to DGND
DGND – 0.3 to DVDD + 0.3
V
Ground voltage difference AGND to DGND
±0.3
V
Input current to all pins except supply
±10
mA
Maximum virtual junction temperature, TJ
+150
°C
Human body model (HBM)
JEDEC standard 22, test method A114-C.01, all pins
±2500
V
Charged device model (CDM)
JEDEC standard 22, test method C101, all pins
±500
V
DVDD to DGND
ESD ratings
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
THERMAL INFORMATION
ADS8528/48/68
THERMAL METRIC (1)
RGC
PM
64 PINS
64 PINS
θJA
Junction-to-ambient thermal resistance
22
48.5
θJCtop
Junction-to-case (top) thermal resistance
9.0
9.4
θJB
Junction-to-board thermal resistance
3.6
21.9
ψJT
Junction-to-top characterization parameter
0.1
0.3
ψJB
Junction-to-board characterization parameter
2.9
21.4
θJCbot
Junction-to-case (bottom) thermal resistance
0.3
n/a
(1)
2
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: ADS8528
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8528
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SAMPLING DYNAMICS
Conversion time
Throughput rate
fDATA
Internal conversion clock
1.33
μs
Serial interface, all four SDOx active
480
kSPS
Parallel interface
650
kSPS
DC ACCURACY
Resolution
12
No missing codes
Bits
12
Bits
Integral linearity error (1)
INL
–0.75
±0.2
0.75
LSB
Differential linearity error
DNL
–0.5
±0.2
0.5
LSB
–1.5
±0.5
1.5
mV
Offset error
–0.65
Offset error matching
0.65
±3.5
Offset error drift
Gain error
Gain error matching
Gain error drift
±0.25
mV
μV/°C
Referenced to voltage at REFIO
–0.5
0.5
%
Between channels of any pair
–0.2
0.2
%
Between any two channels
–0.4
0.4
±6
Referenced to voltage at REFIO
%
ppm/°C
AC ACCURACY
Signal-to-noise ratio
Signal-to-noise ratio + distortion
Total harmonic distortion
(2)
SNR At fIN = 10kHz
73
73.9
dB
SINAD At fIN = 10kHz
73
73.8
dB
SFDR At fIN = 10kHz
Channel-to-channel isolation
At fIN = 10kHz
–3dB small-signal bandwidth
(1)
(2)
–89
THD At fIN = 10kHz
Spurious-free dynamic range
BW
84
92
–84
dB
dB
120
dB
In 4VREF mode
48
MHz
In 2VREF mode
24
MHz
Integral nonlinearity is defined as the maximum deviation from a straight line passing through the end-points of the ideal ADC transfer
function expressed as the number of LSBs or percentage of the specified full-scale range.
Calculated on the first nine harmonics of the input frequency.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
3
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: ADS8548
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8548
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SAMPLING DYNAMICS
Conversion time
Throughput rate
fDATA
Internal conversion clock
1.45
μs
Serial interface, all four SDOx active
450
kSPS
Parallel interface
600
kSPS
DC ACCURACY
Resolution
14
No missing codes
Bits
14
Integral linearity error (1)
INL
Differential linearity error
DNL
Offset error
Bits
–1
±0.5
–1
–1.5
1
LSB
±0.25
1
LSB
±0.5
1.5
mV
–0.65
Offset error matching
0.65
±3.5
Offset error drift
Gain error
Gain error matching
Gain error drift
Referenced to voltage at REFIO
–0.5
0.5
%
Between channels of any pair
–0.2
0.2
%
Between any two channels
–0.4
0.4
Referenced to voltage at REFIO
±0.25
mV
μV/°C
%
±6
ppm/°C
AC ACCURACY
Signal-to-noise ratio
Signal-to-noise ratio + distortion
Total harmonic distortion
(2)
SNR At fIN = 10kHz
84
85
dB
SINAD At fIN = 10kHz
83
84
dB
SFDR At fIN = 10kHz
Channel-to-channel isolation
At fIN = 10kHz
–3dB small-signal bandwidth
(1)
(2)
4
–91
THD At fIN = 10kHz
Spurious-free dynamic range
BW
86
92
–86
dB
dB
120
dB
In 4VREF mode
48
MHz
In 2VREF mode
24
MHz
Integral nonlinearity is defined as the maximum deviation from a straight line passing through the end-points of the ideal ADC transfer
function expressed as the number of LSBs or percentage of the specified full-scale range.
Calculated on the first nine harmonics of the input frequency.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: ADS8568
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8568
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SAMPLING DYNAMICS
Conversion time
Throughput rate
fDATA
Internal conversion clock
1.7
μs
Serial interface, all four SDOx active
400
kSPS
Parallel interface
510
kSPS
DC ACCURACY
Resolution
16
No missing codes
Integral linearity error (1)
INL
DNL
Bits
At TA = –40°C to +85°C, QFN package (RGC)
–3
±1.5
3
LSB
At TA = –40°C to +125°C, QFN package (RGC)
–4
±1.5
4
LSB
At TA = –40°C to +85°C, LQFP package (PM)
–4
±1.5
4
LSB
–4.5
±1.5
4.5
LSB
At TA = –40°C to +85°C
–1
±0.75
1.75
LSB
At TA = –40°C to +125°C
–1
±0.75
2
LSB
–1.5
±0.5
1.5
mV
At TA = –40°C to +125°C, LQFP package (PM)
Differential linearity error
Bits
16
Offset error
–0.65
Offset error matching
0.65
±3.5
Offset error drift
Gain error
Gain error matching
Gain error drift
±0.25
mV
μV/°C
Referenced to voltage at REFIO
–0.5
0.5
%
Between channels of any pair
–0.2
0.2
%
Between any two channels
–0.4
0.4
%
±6
Referenced to voltage at REFIO
ppm/°C
AC ACCURACY
Signal-to-noise ratio
Signal-to-noise ratio + distortion
Total harmonic distortion (2)
Spurious-free dynamic range
SNR
SINAD
THD
SFDR
Channel-to-channel isolation
–3dB small-signal bandwidth
(1)
(2)
At fIN = 10kHz, TA = –40°C to +85°C
90
91.5
dB
At fIN = 10kHz, TA = –40°C to +125°C
89
91.5
dB
At fIN = 10kHz, TA = –40°C to +85°C
87
90
dB
86.5
90
At fIN = 10kHz, TA = –40°C to +125°C
–94
–90
dB
At fIN = 10kHz, TA = –40°C to +125°C
–94
–89.5
dB
At fIN = 10kHz, TA = –40°C to +85°C
At fIN = 10kHz, TA = –40°C to +125°C
At fIN = 10kHz
BW
dB
At fIN = 10kHz, TA = –40°C to +85°C
90
95
dB
89.5
95
dB
120
dB
In 4VREF mode
48
MHz
In 2VREF mode
24
MHz
Integral nonlinearity is defined as the maximum deviation from a straight line passing through the end-points of the ideal ADC transfer
function expressed as the number of LSBs or percentage of the specified full-scale range.
Calculated on the first nine harmonics of the input frequency.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
5
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: GENERAL
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8528, ADS8548, ADS8568
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
ANALOG INPUT
Bipolar full-scale range
CHXX
RANGE pin/RANGE bit = 0
–4VREF
4VREF
RANGE pin/RANGE bit = 1
–2VREF
2VREF
Input range = ±4VREF
Input capacitance
10
Input range = ±2VREF
Input leakage current
Aperture delay
Aperture delay matching
Common CONVST for all channels
Aperture jitter
Power-supply rejection ratio
PSRR At output code FFFFh, related to HVDD and HVSS
V
pF
20
–1
No ongoing conversion
V
pF
1
μA
5
ns
100
ps
50
ps
–78
dB
REFERENCE VOLTAGE OUTPUT (REFOUT)
Reference voltage
Reference voltage drift
Power-supply rejection ratio
Output current
VREF
2.485
2.5
2.515
V
2.5V operation, REFDAC = 3FFh at +25°C
2.496
2.5
2.504
V
3.0V operation, REFDAC = 3FFh
2.985
3.0
3.015
V
3.0V operation, REFDAC = 3FFh at +25°C
2.995
3.0
3.005
±10
dVREF/dT
–2
IREFSC
Turn-on settling time
tREFON
External load capacitance
V
ppm/°C
–77
PSRR At output code FFFFh, related to AVDD
IREFOUT DC current
Short-circuit current (1)
Tuning range
2.5V operation, REFDAC = 3FFh
dB
2
mA
50
mA
10
ms
At REF_xP/N pins
4.7
10
μF
At REFIO pin
100
470
REFDAC Internal reference output voltage range
0.2 VREF
REFDAC resolution
nF
VREF
10
V
Bits
DNLDAC
–1
±0.1
1
LSB
REFDAC integral nonlinearity
INLDAC
–2
±0.1
2
LSB
REFDAC offset error
VOSDAC VREF = 0.5V (DAC = 0CDh)
–4
±0.65
4
LSB
2.5
3.025
REFDAC differential nonlinearity
REFERENCE VOLTAGE INPUT (REFIN)
Reference input voltage
VREFIN
0.5
Input resistance
100
Input capacitance
5
Reference input current
(1)
6
V
MΩ
pF
1
μA
Reference output current is not limited internally.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: GENERAL (continued)
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8528, ADS8548, ADS8568
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
DIGITAL INPUTS (2)
Logic family
CMOS with Schmitt-Trigger
High-level input voltage
0.7 DVDD
DVDD + 0.3
Low-level input voltage
DGND – 0.3
0.3 DVDD
V
–50
50
nA
Input current
VI = DVDD to DGND
Input capacitance
5
V
pF
DIGITAL OUTPUTS (2)
Output capacitance
5
Load capacitance
–50
High-impedance-state output current
Logic family
High-level output voltage
Low-level output voltage
pF
30
pF
50
nA
CMOS
VOH IOH = 100μA
VOL
DVDD – 0.6
V
IOH = –100μA
DGND +
0.4
V
POWER-SUPPLY REQUIREMENTS
Analog supply voltage
AVDD
4.5
5.0
5.5
V
Buffer I/O supply voltage
DVDD
2.7
3.3
5.5
V
Input positive supply voltage
HVDD
5.0
15.0
16.5
V
Input negative supply voltage
HVSS
–16.5
–15.0
–5.0
V
ADS8528, fDATA = maximum
37.9
50.1
mA
ADS8548, fDATA = maximum
37.3
49.3
mA
ADS8568, fDATA = maximum
36.6
48.4
mA
fDATA = 250kSPS, auto-sleep mode
20.3
30.0
mA
fDATA = 200kSPS, auto-sleep mode
17
mA
fDATA = 10kSPS, normal operation
30
mA
fDATA = 10kSPS, auto-sleep mode
4.6
mA
Analog supply current
IAVDD
Auto-sleep mode, no ongoing conversion,
internal conversion clock
Power-down mode
Buffer I/O supply current
0.03
mA
0.5
2.0
mA
fDATA = 250kSPS
0.5
1.4
mA
fDATA = 200kSPS
0.5
mA
0.4
mA
IDVDD fDATA = 10kSPS
Power-down mode
0.35
mA
0.01
mA
ADS8528, fDATA = maximum
3.0
4.2
mA
ADS8548, fDATA = maximum
2.8
3.9
mA
ADS8568, fDATA = maximum
2.3
3.2
mA
fDATA = 250kSPS
1.8
2.4
mA
IHVDD fDATA = 200kSPS
1.5
mA
0.4
mA
fDATA = 10kSPS
(2)
mA
fDATA = maximum
Auto-sleep mode, no ongoing conversion,
internal conversion clock
Input positive supply current
7.0
Auto-sleep mode, no ongoing conversion,
internal conversion clock
0.45
mA
Power-down mode
0.01
mA
Specified by design.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
7
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: GENERAL (continued)
All minimum/maximum specifications are at TA = –40°C to +125°C, specified supply voltage range, VREF = 2.5V (internal),
VIN = ±10V, and fDATA = max, unless otherwise noted. Typical values are at TA = +25°C, HVDD = 15V, HVSS = –15V,
AVDD = 5V, and DVDD = 3.3V.
ADS8528, ADS8548, ADS8568
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
ADS8528, fDATA = maximum
3.4
4.5
mA
ADS8548, fDATA = maximum
3.3
4.4
mA
ADS8568, fDATA = maximum
2.7
3.6
mA
fDATA = 250kSPS
2.1
2.6
mA
IHVSS fDATA = 200kSPS
1.7
mA
0.4
mA
POWER-SUPPLY REQUIREMENTS (continued)
Input negative supply current
fDATA = 10kSPS
Auto-sleep mode, no ongoing conversion,
internal conversion clock
0.35
Power-down mode
Power dissipation (3)
0.01
mA
ADS8528, fDATA = maximum
287.1
430.1
mW
ADS8548, fDATA = maximum
279.7
419.1
mW
ADS8568, fDATA = maximum
259.7
389.4
mW
fDATA = 250kSPS, auto-sleep mode
161.7
255.2
mW
fDATA = 200kSPS, auto-sleep mode
151.2
mW
fDATA = 10kSPS, normal operation
163.3
mW
fDATA = 10kSPS, auto-sleep mode
36.3
mW
Auto-sleep mode, no ongoing conversion,
internal conversion clock
Power-down mode
Operating ambient temperature
range
(3)
8
mA
–40
TA
25
53.6
mW
0.6
mW
+125
°C
Maximum power dissipation values are specified with HVDD = 15V and HVSS = –15V.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PARAMETER MEASUREMENT INFORMATION
TIMING CHARACTERISTICS
XCLK
(C29 = 1)
tSCVX
tCVL
tXCLK
CONVST_x
tACQ
tCONV
tDCVB
BUSY
(C27 = C26 = 0)
tFSCV
tBUFS
FS
tSCLK
32
1
SCLK
tHDO
tPDDO
tDMSB
CH_x0
MSB
SDO_x
CH_x1
D3
CH_x1
D2
tDTRI
CH_x1
D1
tSUDI
SDI or
DCIN_x
Don’t Care
D31
D3
CH_x1
LSB
tHDI
D2
D1
D0
Don’t Care
Figure 1. Serial Operation Timing Diagram (All Four SDO_x Active)
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
9
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Table 1. Serial Interface Timing Requirements (1) (2)
TEST
CONDITION
PARAMETER
tSCVX
tXCLK
CONVST_x high to XCLK rising edge
setup time
External conversion clock period
External conversion clock frequency
CLKSEL = 1
CONVST_x low time
tACQ
Acquisition time
MIN
TYP
ADS8528
66.67
ns
ADS8548
72.46
ns
ADS8568
85.11
ADS8528
1
ADS8548
ADS8568
ns
15.0
MHz
1
13.8
MHz
1
11.75
MHz
40
60
20
tDCVB
CONVST_x high to BUSY high delay
tBUFS
BUSY low to FS low time
tFSCV
Bus access finished to next conversion
start time
tSCLK
%
ns
280
Conversion time
UNIT
ns
ns
19
tCONV
MAX
6
External conversion clock duty cycle
tCVL
ADS8528, ADS8548, ADS8568
20 tCCLK or tXCLK
ADS8528,
CLKSEL = 0
1.33
μs
ADS8548,
CLKSEL = 0
1.45
μs
ADS8568,
CLKSEL = 0
1.7
μs
25
ns
0
ns
ADS8528
0
ns
ADS8548
20
ns
ADS8568
40
ns
0.022
10
μs
Serial clock frequency
0.1
45
MHz
Serial clock duty cycle
40
60
%
12
ns
Serial clock period
tDMSB
FS low to MSB valid delay
tHDO
Output data to SCLK falling edge hold time
tPDDO
SCLK falling edge to new data valid
propagation delay
tDTRI
FS high to SDO_x three-state delay
tSUDI
Input data to SCLK falling edge setup time
3
ns
tHDI
Input data to SCLK falling edge hold time
5
ns
(1)
(2)
10
5
ns
17
ns
10
ns
Over recommended operating free-air temperature range TA, AVDD = 5V, and DVDD = 2.7V to 5.5V, unless otherwise noted.
All input signals are specified with tR = tF = 1.5ns (10% to 90% of DVDD) and timed from a voltage level of (VIL + VIH)/2.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
tCVL
CONVST_x
tCONV
tACQ
tDCVB
BUSY
(C27 = C26 = 0)
tBUCS
tCSCV
CS
tCSRD
tRDCS
tRDL
tRDH
RD
tPDDO
CH
A0
DB[15:0]
CH
A1
CH
B0
CH
B1
tHDO
CH
C0
CH
C1
tDTRI
CH
D0
CH
D1
Figure 2. Parallel Read Access Timing Diagram
Table 2. Parallel Interface Timing Requirements (Read Access) (1) (2)
TEST
CONDITION
PARAMETER
tCVL
CONVST_x low time
tACQ
Acquisition time
ADS8528, ADS8548, ADS8568
MIN
MAX
20
Conversion time
tDCVB
CONVST_x high to BUSY high delay
tBUCS
BUSY low to CS low time
tCSCV
Bus access finished to next conversion
start time (3)
UNIT
ns
280
19
tCONV
TYP
ns
20 tCCLK or tXCLK
ADS8528,
CLKSEL = 0
1.33
µs
ADS8548,
CLKSEL = 0
1.45
µs
ADS8568,
CLKSEL = 0
1.7
µs
25
ns
0
ns
ADS8528
0
ns
ADS8548
20
ns
ADS8568
40
ns
tCSRD
CS low to RD low time
0
ns
tRDCS
RD high to CS high time
0
ns
tRDL
RD pulse width
20
ns
tRDH
Minimum time between two read accesses
2
ns
tPDDO
RD or CS falling edge to data valid propagation
delay
tHDO
Output data to RD or CS rising edge hold time
tDTRI
CS high to DB[15:0] three-state delay
(1)
(2)
(3)
15
5
ns
ns
10
ns
Over recommended operating free-air temperature range TA, AVDD = 5V, and DVDD = 2.7V to 5.5V, unless otherwise noted.
All input signals are specified with tR = tF = 1.5ns (10% to 90% of DVDD) and timed from a voltage level of (VIL + VIH)/2.
Refer to CS signal or RD, whichever occurs first.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
11
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
CS
tCSWR
tWRL tWRH
tWRCS
WR
tSUDI
tHDI
C
[31:16]
DB[15:0]
C
[15:0]
Figure 3. Parallel Write Access Timing Diagram
Table 3. Parallel Interface Timing Requirements (Write Access) (1) (2)
ADS8528, ADS8548, ADS8568
PARAMETER
tCSWR
CS low to WR low time
tWRL
MIN
TYP
MAX
UNIT
0
ns
WR low pulse width
15
ns
tWRH
Minimum time between two write accesses
10
ns
tWRCS
WR high to CS high time
0
ns
tSUDI
Output data to WR rising edge setup time
5
ns
tHDI
Data output to WR rising edge hold time
5
ns
(1)
(2)
Over recommended ambient temperature range TA, AVDD = 5V, and DVDD = 2.7V to 5.5V, unless otherwise noted.
All input signals are specified with tR = tF = 1.5ns (10% to 90% of DVDD) and timed from a voltage level of (VIL + VIH)/2.
EQUIVALENT CIRCUITS
Input range: ±2VREF
RSER = 200W
Input range: ±4VREF
RSW = 130W
RSER = 200W
CH_XX
RSW = 130W
CH_XX
CS = 20pF
CPAR = 5pF
CS = 10pF
VDC
CPAR = 5pF
VDC
CS = 20pF
AGND
CS = 10pF
AGND
RSER = 200W
RSW = 130W
RSER = 200W
RSW = 130W
Figure 4. Equivalent Input Circuits
12
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PIN CONFIGURATIONS
AGND
REFBP
CH_B0
50
49
52
51
REFBN
AVDD
53
REFN
CH_B1
54
56
55
AVDD
REFIO
57
CH_C1
AGND
58
60
59
AVDD
REFCN
61
REFCP
AGND
62
CH_C0
64
63
RGC PACKAGE
QFN-64
(TOP VIEW)
HVSS
1
48
HVDD
CH_D1
2
47
CH_A1
REFDN
3
46
REFAN
AVDD
4
45
AVDD
AGND
5
44
AGND
REFDP
6
43
REFAP
CH_D0
7
42
CH_A0
PAR/SER
8
41
HW/SW
STBY
9
40
CONVST_D
RESET
10
39
CONVST_C
REFEN/WR
11
38
CONVST_B
RD
12
37
CONVST_A
CS/FS
13
36
ASLEEP
AVDD
14
35
BUSY/INT
AGND
15
34
RANGE/XCLK
DB15/SDO_D
16
33
DB0/DCIN_D
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
DB14/SDO_C
DB13/SDO_B
DB12/SDO_A
DB11/REFBUFEN
DB10/SCLK
DB9/SDI
DB8/DCEN
DGND
DVDD
DB7
DB6/SEL_B
DB5/SEL_CD
DB4
DB3/DCIN_A
DB2/DCIN_B
DB1/DCIN_C
7.3-mm x 7.3-mm
Exposed Thermal Pad
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
13
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
14
CH_C0
REFCP
AGND
AVDD
REFCN
CH_C1
AGND
AVDD
REFIO
REFN
CH_B1
REFBN
AVDD
AGND
REFBP
CH_B0
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
PM PACKAGE
LQFP-64
(TOP VIEW)
STBY
9
40
CONVST_D
RESET
10
39
CONVST_C
REFEN/WR
11
38
CONVST_B
RD
12
37
CONVST_A
CS/FS
13
36
ASLEEP
AVDD
14
35
BUSY/INT
AGND
15
34
RANGE/XCLK
DB15/SDO_D
16
33
DB0/DCIN_D
32
HW/SW
DB1/DCIN_C
41
31
8
DB2/DCIN_B
PAR/SER
30
CH_A0
DB3/DCIN_A
42
29
7
DB4
CH_D0
28
REFAP
DB5/SEL_CD
43
27
6
DB6/SEL_B
REFDP
26
AGND
DB7
44
25
5
DVDD
AGND
24
AVDD
DGND
45
23
4
DB8/DCEN
AVDD
22
REFAN
DB9/SDI
46
21
3
DB10/SCLK
REFDN
20
CH_A1
DB11/REFBUFEN
47
19
2
DB12/SDO_A
CH_D1
18
HVDD
DB13/SDO_B
48
17
1
DB14/SDO_C
HVSS
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PIN DESCRIPTIONS
DESCRIPTION
PIN #
NAME
TYPE (1)
PARALLEL INTERFACE (PAR/SER = 0)
SERIAL INTERFACE (PAR/SER = 1)
1
HVSS
P
Negative supply voltage for the analog inputs.
Decouple according to the Power Supply section.
2
CH_D1
AI
Analog input of channel D1.
The input voltage range is controlled by the RANGE pin in hardware mode or by the Configuration Register
(CONFIG) bit C19 (RANGE_D) in software mode.
This pin can be powered down using CONFIG bit C18 (PD_D) in software mode.
3
REFDN
AI
Decoupling capacitor input for reference of channel pair D.
Connect to the decoupling capacitor and AGND according to the Power Supply section.
4, 14,
45, 52,
57, 61
AVDD
P
Analog power supply.
Decouple according to the Power Supply section.
5, 15,
44, 51,
58, 62
AGND
P
Analog ground; connect to the analog ground plane.
6
REFDP
AI
Decoupling capacitor input for the channel pair D reference.
Connect to the decoupling capacitor according to the Power Supply section.
7
CH_D0
AI
Analog input of channel D0.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C19 (RANGE_D) in
software mode. This pin can be powered down using CONFIG bit C18 (PD_D) in software mode.
8
PAR/SER
DI
Interface mode selection input.
When low, the parallel interface is selected. When high, the serial interface is enabled.
9
STBY
DI
Hardware mode (HW/SW = 0): standby mode input.
When low, the entire device is powered down (including the internal conversion clock source and reference).
When high, the device operates in normal mode.
Software mode (HW/SW = 1): connect to DGND or DVDD.
The standby mode can be activated using CONFIG bit C25 (STBY).
10
11
REFEN/WR
DI
DI/DI
Reset input, active high.
This pin aborts any ongoing conversions and resets the internal Configuration Register (CONFIG) to 000003FFh.
A valid reset pulse should be at least 50 ns long.
Hardware mode (HW/SW = 0): internal reference
enable input.
When high, the internal reference is enabled (the
reference buffers are also enabled).
When low, the internal reference is disabled and an
external reference is applied at REFIO.
Hardware mode (HW/SW = 0): internal reference
enable input.
When high, the internal reference is enabled (the
reference buffers are also enabled).
When low, the internal reference is disabled and an
external reference is applied at REFIO.
Software mode (HW/SW = 1): write input.
The parallel data input is enabled when CS and WR are
low. The internal reference is enabled by CONFIG bit
C15 (REFEN).
Software mode (HW/SW = 1): connect to DGND or
DVDD. The internal reference is enabled by CONFIG bit
C15 (REFEN).
12
RD
DI/DI
Read data input.
When low, the parallel data output is enabled (if CS = 0).
When high, the data output is disabled.
Must be connected to DGND.
13
CS/FS
DI/DI
Chip select input.
When low, the parallel interface is enabled. When high,
the interface is disabled.
Frame synchronization.
The FS falling edge controls the frame transfer.
16
DB15/SDO_D
DIO/DO
Data bit 15 (MSB) input/output.
Output is sign extension for the ADS8528/48.
When SEL_CD = 1, this pin is the data output for
channel pair D.
When SEL_CD = 0, this pin should be tied to DGND.
17
DB14/SDO_C
DIO/DO
Data bit 14 input/output.
Output is sign extension for the ADS8528/48.
When SEL_CD = 1, this pin is the data output for
channel pair C.
When SEL_CD = 0, this pin should be tied to DGND.
18
DB13/SDO_B
DIO/DO
Data bit 13 input/output.
Output is sign extension for the ADS8528 and MSB for
the ADS8548.
When SEL_B = 1, this pin is the data output for channel
pair B. When SEL_B = 0, this pin should be tied to
DGND. When SEL_CD = 0, data from channel pair D
are also available on this output.
DIO/DO
Data bit 12 input/output.
Output is sign extension for the ADS8528.
Data output for channel pair A.
When SEL_CD = 0, data from channel pair C are also
available on this output.
When SEL_CD = 0 and SEL_B = 0, SDO_A acts as
single data output for all eight channels.
19
(1)
RESET
DB12/SDO_A
AI = analog input; AIO = analog input/output; DI = digital input; DO = digital output; DIO = digital input/output; and P = power supply.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
15
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PIN DESCRIPTIONS (continued)
DESCRIPTION
PIN #
NAME
TYPE (1)
PARALLEL INTERFACE (PAR/SER = 0)
DB11/REFBUFE
N
DIO/DI
21
DB10/SCLK
DIO/DI
Data bit 10 input/output
22
DB9/SDI
DIO/DI
Data bit 9 input/output
23
DB8/DCEN
DIO/DI
Data bit 8 input/output
24
DGND
P
Buffer I/O ground, connect to digital ground plane
25
DVDD
P
Buffer I/O supply, connect to digital supply.
Decouple according to the Power Supply section.
26
DB7
DIO
20
27
DB6/SEL_B
DIO/DI
Data bit 11 input/output.
Output is MSB for the ADS8528.
SERIAL INTERFACE (PAR/SER = 1)
Hardware mode (HW/SW = 0): reference buffer
enable input.
When low, all internal reference buffers are enabled
(mandatory if internal reference is used).
When high, all reference buffers are disabled.
Software mode (HW/SW = 1): connect to
DGND or DVDD.
The internal reference buffers are controlled by bit C14
(REFBUFEN) in the Configuration Register (CONFIG).
Serial interface clock input.
Hardware mode (HW/SW = 0): connect to DGND.
Software mode (HW/SW = 1): serial data input.
Daisy-chain enable input.
When high, DB[3:0] serve as daisy-chain inputs
DCIN_[A:D].
If daisy-chain mode is not used, connect to DGND.
Data bit 7 input/output
Must be connected to DGND
Data bit 6 input/output
Select SDO_B input.
When low, SDO_B is disabled and data from all eight
channels are only available through SDO_A.
When high and SEL_CD = 0, data from channel pairs B
and D are available on SDO_B. When SEL_CD = 1,
data from channel pair B are available on SDO_B.
28
DB5/SEL_CD
DIO/DI
Data bit 5 input/output
Select SDO_C and SDO_D input.
When high, data from channel pair C are available on
SDO_C while data from channel pair D are available on
SDO_D. When low and SEL_B = 1, data from channel
pairs A and C are available on SDO_A while data from
channel pairs B and D are available on SDO_B. When
low and SEL_B = 0, data from all eight channels are
avaiable on SDO_A.
29
DB4
DIO
Data bit 4 input/output
Connect to DGND
30
DB3/DCIN_A
DIO/DI
Data bit 3 input/output
When DCEN = 1, this pin is the daisy-chain data input
for SDO_A of the previous device in the chain. When
DCEN = 0, connect to DGND.
31
DB2/DCIN_B
DIO/DI
Data bit 2 input/output
When DCEN = 1 and SEL_B = 1, this pin is the
daisy-chain data input for SDO_B of the previous device
in the chain. When DCEN = 0, connect to DGND.
32
DB1/DCIN_C
DIO/DI
Data bit 1 input/output
When DCEN = 1 and SEL_CD = 1, this pin is the
daisy-chain data input for SDO_C of the previous
device in the chain.
When DCEN = 0, connect to DGND.
33
DB0/DCIN_D
DIO/DI
Data bit 0 (LSB) input/output
When DCEN = 1 and SEL_CD = 1, this pin is the
daisy-chain data input for SDO_D of the previous
device in the chain.
When DCEN = 0, connect to DGND.
Hardware mode (HW/SW = 0): analog input voltage range select input.
When low, the analog input voltage range is ±4VREF. When high, the analog input voltage range is ±2VREF.
34
35
16
RANGE/XCLK
BUSY/INT
DI/DI/DO
DO
Sofware mode (HW/SW = 1): this pin is an external conversion clock input if CONFIG bit C29 = 1 (CLKSEL); or an
internal conversion clock output if CONFIG bit C28 = 1 (CLKOUT_EN).
If this pin is not used, connect to DGND.
When CONFIG bit C27 = 0 (BUSY/INT) this pin is a converter busy status output.
This pin transitions high when a conversion has been started and transitions low for a single conversion clock cycle
(tCCLK) whenever a channel pair conversion is completed and stays low when the conversion of the last channel pair
has completed.
When bit C27 = 1 (BUSY/INT in CONFIG), this pin is an interrupt output. This pin transitions high after a conversion
has been completed and remains high until the next read access. This mode can only be used if all eight channels
are sampled simultaneously (all CONVST_x tied together). The polarity of the BUSY/INT output can be changed
using bit C26 (BUSY L/H) in the Configuration Register.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
PIN DESCRIPTIONS (continued)
DESCRIPTION
PIN #
NAME
TYPE (1)
PARALLEL INTERFACE (PAR/SER = 0)
SERIAL INTERFACE (PAR/SER = 1)
36
ASLEEP
DI
Auto-sleep enable input.
When low, the device operates in normal mode.
When high, the device works in auto-sleep mode where the hold mode and the actual conversion is activated 6
conversion clock (tCCLK) cycles after issuing a conversion start using a CONVST_x. This mode is recommended to
save power if the device runs at a lower data rate; see the Reset and Power-Down Modes section for more details.
37
CONVST_A
DI
Conversion start of channel pair A.
The rising edge of this signal initiates simultaneous conversion of analog signals at inputs CH_A[1:0].
This signal resets the internal channel state machine that causes the data output to start with conversion results of
channel A0 with the next read access.
38
CONVST_B
DI
Conversion start of channel pair B.
The rising edge of this signal initiates simultaneous conversion of analog signals at inputs CH_B[1:0].
39
CONVST_C
DI
Conversion start of channel pair C.
The rising edge of this signal initiates simultaneous conversion of analog signals at inputs CH_C[1:0].
40
CONVST_D
DI
Conversion start of channel pair D.
The rising edge of this signal initiates simultaneous conversion of analog signals at inputs CH_D[1:0].
41
HW/SW
DI
Mode selection input.
When low, the hardware mode is selected and the device functions according to the settings of the external pins.
When high, the software mode is selected in which the device is configured by writing to the Configuration Register
(CONFIG).
42
CH_A0
AI
Analog input of channel A0; channel A is the master channel pair that is always active.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C24 (RANGE_A) in
software mode. In cases where channel pairs of the device are used at different data rates, channel pair A should
always run at the highest data rate.
43
REFAP
AI
Decoupling capacitor input for reference of channel pair A.
Connect to the decoupling capacitor according to the Power Supply section.
46
REFAN
AI
Decoupling capacitor input for reference of channel pair A.
Connect to the decoupling capacitor and AGND according to the Power Supply section.
47
CH_A1
AI
Analog input of channel A1; channel A is the master channel pair that is always active.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C24 (RANGE_A) in
software mode. In cases where channel pairs of the device are used at different data rates, channel pair A should
always run at the highest data rate.
48
HVDD
P
Positive supply voltage for the analog inputs.
Decouple according to the Power Supply section.
49
CH_B0
AI
Analog input of channel B0.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C23 (RANGE_B) in
software mode.
50
REFBP
AI
Decoupling capacitor input for reference of channel pair B.
Connect to the decoupling capacitor according to the Power Supply section.
53
REFBN
AI
Decoupling capacitor input for reference of channel pair B.
Connect to the decoupling capacitor and AGND according to the Power Supply section.
54
CH_B1
AI
Analog input of channel B1.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C23 (RANGE_B) in
software mode.
55
REFN
AI
Negative reference input/output pin.
Connect to a decoupling capacitor and AGND according to the Power Supply section.
56
REFIO
AIO
59
CH_C1
AI
Analog input of channel C1.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C21 (RANGE_C) in
software mode.
60
REFCN
AI
Decoupling capacitor input for reference of channel pair C.
Connect to the decoupling capacitor and AGND according to the Power Supply section.
63
REFCP
AI
Decoupling capacitor input for reference of channel pair C.
Connect to the decoupling capacitor according to the Power Supply section.
64
CH_C0
AI
Analog input of channel C0.
The input voltage range is controlled by the RANGE pin in hardware mode or by CONFIG bit C21 (RANGE_C) in
software mode.
Reference voltage input/output.
The internal reference is enabled by the REFEN/WR pin in hardware mode or by CONFIG bit C15 (REFEN) in
software mode. The output value is controlled by the internal DAC (CONFIG bits C[9:0]).
Connect to a decoupling capacitor according to the Power Supply section.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
17
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
HVDD
HVSS
AVDD
DVDD
Clock
Generator
CH_A0
SAR
ADC
AGND
BUSY/INT
CONVST_A
RANGE/XCLK
HW/SW
Control
Logic
REFAP
CH_A1
REFEN/WR
SAR
ADC
AGND
STBY
RESET
CH_B0
SAR
ADC
AGND
CONVST_B
REFBP
CH_B1
SAR
ADC
AGND
Config
Register
CH_C0
SAR
ADC
AGND
CONVST_C
REFCP
CH_C1
SAR
ADC
AGND
CS/FS
CH_D0
SAR
ADC
AGND
RD
DB[15:0]
I/O
CONVST_D
ASLEEP
PAR/SER
REFDP
SCLK
CH_D1
SAR
ADC
AGND
String
DAC
REFIO
AGND
18
2.5
VREF
DGND
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
INL vs CODE
(ADS8528)
DNL vs CODE
(ADS8528)
0.75
0.5
0.4
0.5
0.3
0.2
DNL (LSB)
INL (LSB)
0.25
0
−0.25
0.1
0
−0.1
−0.2
−0.3
−0.5
−0.4
500
1000
1500
2000
Code
2500
3000
3500
−0.5
4000
0.4
INL (LSB)
0.6
0.4
0.2
0
−0.2
2500
3000
−0.6
−0.8
−0.8
−1
8000 10000 12000 14000 16000
Code
G003
0
2000
4000
6000
8000 10000 12000 14000 16000
Code
G004
Figure 7.
Figure 8.
DNL vs CODE
(ADS8548 ±10VIN Range)
DNL vs CODE
(ADS8548 ±5VIN Range)
1
1
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0
−0.2
0.2
0
−0.2
−0.4
−0.4
−0.6
−0.6
−0.8
−0.8
4000
6000
8000 10000 12000 14000 16000
Code
G005
G002
0
−0.4
6000
4000
−0.2
−0.6
4000
3500
0.2
−0.4
2000
2000
Code
INL vs CODE
(ADS8548 ±5VIN Range)
0.6
0
1500
INL vs CODE
(ADS8548 ±10VIN Range)
1
−1
1000
Figure 6.
0.8
2000
500
Figure 5.
1
0
0
G001
0.8
−1
DNL (LSB)
0
DNL (LSB)
INL (LSB)
−0.75
−1
0
2000
4000
Figure 9.
6000
8000 10000 12000 14000 16000
Code
G006
Figure 10.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
19
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
3
2
2
1
1
INL (LSB)
3
0
0
−1
−1
−2
−2
−3
DNL (LSB)
INL vs CODE
(ADS8568 ±5VIN Range)
0
−3
8190 16380 24570 32760 40950 49140 57330 65520
Code
G007
DNL vs CODE
(ADS8568 ±10VIN Range)
DNL vs CODE
(ADS8568 ±5VIN Range)
3
2
2
1
1
0
0
−1
−1
−2
−2
0
8190 16380 24570 32760 40950 49140 57330 65520
Code
G008
Figure 12.
3
−3
0
Figure 11.
DNL (LSB)
INL (LSB)
INL vs CODE
(ADS8568 ±10VIN Range)
−3
8190 16380 24570 32760 40950 49140 57330 65520
Code
G009
0
8190 16380 24570 32760 40950 49140 57330 65520
Code
G010
Figure 13.
Figure 14.
OFFSET ERROR vs TEMPERATURE
GAIN ERROR vs TEMPERATURE
1.5
1
0.8
0.6
0.5
Gain Error (%)
Offset Error (mV)
1
0
−0.5
0.4
0.2
0
−0.2
−0.4
−0.6
−1
−0.8
−1.5
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
−1
−40 −25 −10
5
G011
Figure 15.
20
20 35 50 65
Temperature (°C)
80
95
110 125
G012
Figure 16.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
PSRR vs SUPPLY NOISE FREQUENCY
CONVERSION TIME vs TEMPERATURE
Power-Supply Rejection Ratio (dB)
−40
1.8
CSUPPLY = 100nF on AVDD
CSUPPLY = 1µF on HVDD
CSUPPLY = 1µF on HVSS
1.7
Conversion Time (µs)
−50
−60
−70
−80
AVDD
HVDD
HVSS
−90
−100
0
20
40
1.6
1.5
1.4
1.3
1.2
ADS8568
ADS8548
ADS8528
1.1
1
−40 −25 −10
60
80 100 120 140 160 180 200
Supply Noise Frequency (kHz)
G013
5
Figure 17.
Signal-to-Noise Ratio (dB)
7389
110 125
G014
46
8
0
94
92
90
88
86
84
82
80
78
76
74
ADS8568
ADS8548
ADS8528
72
70
−40 −25 −10
0
5
Figure 19.
20 35 50 65
Temperature (°C)
80
95
110 125
G016
Figure 20.
SINAD vs TEMPERATURE
THD vs TEMPERATURE
94
−82
Total Harmonic Distortion (dB)
Signal-to-Noise Ratio and Distortion (dB)
95
SNR vs TEMPERATURE
8947
92
90
88
86
84
82
80
78
76
74
72
70
−40 −25 −10
80
Figure 18.
CODE HISTOGRAM
(ADS8568, 16390 Hits)
0
20 35 50 65
Temperature (°C)
ADS8568
ADS8548
ADS8528
5
20 35 50 65
Temperature (°C)
80
95
110 125
−84
ADS8568
ADS8548
ADS8528
−86
−88
−90
−92
−94
−96
−40 −25 −10
G017
Figure 21.
5
20 35 50 65
Temperature (°C)
80
95
110 125
G018
Figure 22.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
21
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
FREQUENCY SPECTRUM
(ADS8568, 2048-Point FFT, fIN = 10kHz, ±10VIN Range)
SFDR vs TEMPERATURE
0
ADS8568
ADS8548
ADS8528
98
−40
96
94
92
−60
−80
−100
−120
−140
90
−160
88
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
−180
110 125
0
25
50
75
G019
100 125 150 175 200 225 250
Frequency (kHz)
G020
Figure 23.
Figure 24.
FREQUENCY SPECTRUM
(ADS8568, 2048-Point FFT, fIN = 10kHz, ±5VIN Range)
CHANNEL-TO-CHANNEL ISOLATION vs
INPUT NOISE FREQUENCY
0
140
−20
135
−40
130
−60
Isolation (dB)
Amplitude (dB)
−20
Amplitude (dB)
Spurious−Free Dynamic Range (dB)
100
−80
−100
−120
125
120
115
−140
110
−160
105
−180
0
25
50
75
100
100 125 150 175 200 225 250
Frequency (kHz)
G021
0
25
50
75 100 125 150 175 200 225 250
Noise Frequency (kHz)
G022
Figure 25.
Figure 26.
INTERNAL REFERENCE VOLTAGE vs
ANALOG SUPPLY VOLTAGE (2.5V Mode)
INTERNAL REFERENCE VOLTAGE vs TEMPERATURE
(2.5V Mode)
2.504
2.515
2.503
2.51
2.505
2.501
VREF (V)
VREF (V)
2.502
2.5
2.499
2.5
2.495
2.498
2.49
2.497
2.496
4.5
4.6
4.7
4.8
4.9
5
5.1
AVDD (V)
5.2
5.3
5.4
5.5
2.485
−40 −25 −10
5
G023
Figure 27.
22
20 35 50 65
Temperature (°C)
80
95
110 125
G024
Figure 28.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
INTERNAL REFERENCE VOLTAGE vs TEMPERATURE
(3.0V Mode)
ADS8568 ANALOG SUPPLY CURRENT vs TEMPERATURE
3.015
50
fDATA = MAX
fDATA = 250kSPS (Auto-Sleep)
46
3.01
42
IAVDD (mA)
VREF (V)
3.005
3
2.995
38
34
30
26
22
2.99
18
2.985
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
14
−40 −25 −10
110 125
20 35 50 65
Temperature (°C)
80
95
110 125
G026
Figure 29.
Figure 30.
ADS8568 ANALOG SUPPLY CURRENT vs DATA RATE
BUFFER I/O SUPPLY CURRENT vs TEMPERATURE
50
2
Normal Operation
Auto-Sleep Mode
45
40
1.6
35
1.4
30
25
20
1.2
1
0.8
15
0.6
10
0.4
5
0.2
0
0
51
fDATA = MAX
fDATA = 250kSPS (Auto-Sleep)
1.8
IDVDD (mA)
IAVDD (mA)
5
G025
0
−40 −25 −10
102 153 204 255 306 357 408 459 510
Sample Rate (kSPS)
G027
5
20 35 50 65
Temperature (°C)
80
95
110 125
G028
Figure 31.
Figure 32.
ADS8568 INPUT SUPPLY CURRENT vs TEMPERATURE
ADS8568 INPUT SUPPLY CURRENT vs INPUT SUPPLY
VOLTAGE
4.5
IHVxx (mA)
3.5
IHVDD (fDATA = MAX)
IHVSS (fDATA = MAX)
IHVDD (fDATA = 250kSPS, Auto-Sleep)
IHVSS (fDATA = 250kSPS, Auto-Sleep)
4
3.5
IHVxx (mA)
4
4.5
IHVDD (fDATA = MAX)
IHVSS (fDATA = MAX)
IHVDD (fDATA = 250kSPS, Auto-Sleep)
IHVSS (fDATA = 250kSPS, Auto-Sleep)
3
2.5
3
2.5
2
1.5
2
1
1.5
1
−40 −25 −10
0.5
5
20 35 50 65
Temperature (°C)
80
95
110 125
0
5
6
7
G029
Figure 33.
8
9
10
11
12
HVDD, HVSS (V)
13
14
15
G030
Figure 34.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
23
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Graphs are valid for all devices of the family, at TA = +25°C, HVDD = 15V, HVSS = –15V, AVDD = 5V, and DVDD = 3.3V,
VREF = 2.5V (internal), VIN = ±10V, and fDATA = maximum, unless otherwise noted.
IHVxx (mA)
ADS8568 INPUT SUPPLY CURRENT vs DATA RATE
4.5
4.25
4
3.75
3.5
3.25
3
2.75
2.5
2.25
2
1.75
1.5
1.25
1
0.75
0.5
0.25
0
IHVDD
IHVSS
IHVDD (Auto-Sleep)
IHVSS (Auto-Sleep)
0
51
102 153 204 255 306 357 408 459 510
Sample Rate (kSPS)
G031
Figure 35.
24
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
GENERAL DESCRIPTION
The ADS8528/48/68 series includes eight 12-, 14-, and 16-bit analog-to-digital converters (ADCs), respectively,
that operate based on the successive approximation register (SAR) architecture. This architecture is designed on
the charge redistribution principle, which inherently includes a sample-and-hold function. The eight analog inputs
are grouped into four channel pairs. These channel pairs can be sampled and converted simultaneously,
preserving the relative phase information of the signals of each pair. Separate conversion start signals allow
simultaneous sampling on each channel pair of four, six, or eight channels. These devices accept single-ended,
bipolar analog input signals in the selectable ranges of ±4VREF or ±2VREF with an absolute value of up to
±12V; see the Analog Inputs section.
The devices offer an internal 2.5V or 3V reference source followed by a 10-bit digital-to-analog converter (DAC)
that allows the reference voltage VREF to be adjusted in 2.44mV or 2.93mV steps, respectively.
The ADS8528/48/68 also offer a selectable parallel or serial interface that can be used in hardware or software
mode; see the Device Configuration section for details. The Analog and Digital sections describe the functionality
and control of the device in detail.
ANALOG
This section addresses the analog input circuit, the ADCs and control signals, and the reference design of the
device.
Analog Inputs
The inputs and the converters are of single-ended bipolar type. The absolute voltage range can be selected
using the RANGE pin (in hardware mode) or RANGE_x bits (in software mode) in the Configuration (CONFIG)
Register to either ±4VREF or ±2VREF. With the internal reference set to 2.5V (VREF bit C13 = 0 in the CONFIG
Register), the input voltage range can be ±10V or ±5V. With the internal reference source set to 3V (CONFIG bit
C13 = 1), an input voltage range of ±12V or ±6V can be configured. The logic state of the RANGE pin is latched
with the falling edge of BUSY (if CONFIG bit C26 = 0).
The input current on the analog inputs depends on the actual sample rate, input voltage, and signal source
impedance. Essentially, the current into the analog inputs charges the internal capacitor array only during the
sampling period (tACQ). The source of the analog input voltage must be able to charge the input capacitance of
10pF in ±4VREF mode or of 20pF in ±2VREF mode to a 12-, 14-, or 16-bit accuracy level within the acquisition
time; see Figure 4. During the conversion period, there is no further input current flow and the input impedance is
greater than 1MΩ. To ensure a defined start condition, the sampling capacitors of the ADS8528/48/68 are
pre-charged to a fixed internal voltage before switching into sampling mode.
To maintain the linearity of the converter, the inputs should always remain within the specified range shown in
the Electrical Characteristics table. The minimum –3dB bandwidth of the driving operational amplifier can be
calculated using Equation 1:
ln(2)(n + 1)
f3dB =
2ptACQ
(1)
where:
n = 12, 14, or 16; n is the resolution of the ADS8528/48/68
With a minimum acquisition time of tACQ = 280ns, the required minimum bandwidth of the driving amplifier is
5.2MHz for the ADS8528, 6.0MHz for the ADS8548, or 6.7MHz for the ADS8568. The required bandwidth can be
lower if the application allows a longer acquisition time. A gain error occurs if a given application does not fulfill
the bandwidth requirement shown in Equation 1.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
25
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
A driving operational amplifier may not be required, if the impedance of the signal source (RSOURCE) fulfills the
requirement of Equation 2:
tACQ
RSOURCE <
- (RSER + RSW)
CS ln(2)(n + 1)
(2)
where:
n = 12, 14, or 16; n is the resolution of the ADC,
CS = 10pF is the sample capacitor value in VIN = ±4VREF mode,
RSER = 200Ω is the input resistor value,
and RSW = 130Ω is the switch resistance value.
With a minimum acquisition time of tACQ = 280ns, the maximum source impedance should be less than 2.7kΩ for
the ADS8528, 2.3kΩ for the ADS8548, and 2.0kΩ for the ADS8568 in ±4VREF mode, or less than 1.2kΩ for the
ADS8528, 1.0kΩ for the ADS8548, and 0.8kΩ for the ADS8568 in ±2VREF mode. The source impedance can be
higher if the application allows longer acquisition time.
Analog-to-Digital Converter (ADC)
The device includes eight ADCs that operate with either an internal or an external conversion clock.
Conversion Clock
The device uses either an internally-generated (CCLK) or an external (XCLK) conversion clock signal (in
software mode only). In default mode, the device generates an internal clock. In this case, a complete conversion
including the pre-charging of the sample capacitors takes 19 to 20 clock cycles, depending on the setup time of
the incoming CONVST_x signal with relation to the rising edge of the CCLK.
When CLKSEL bit is set high (CONFIG bit C29), an external conversion clock can be applied on pin 34. A
complete conversion process requires 19 clock cycles in this case if the tSCVX timing requirement is fulfilled. The
external clock can remain low between conversions.
If the application requires lowest power dissipation at low data rates, it is recommended to use the auto-sleep
mode, activated using pin 36 (ASLEEP). In this case, a conversion cycle takes up to 26 clock cycles (see the
Reset and Power-Down Modes section for more details).
26
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
CONVST_x
The analog inputs of each channel pair (CH_x0/1) are held with the rising edge of the corresponding CONVST_x
signal. The conversion automatically starts with the next rising edge of the conversion clock. CONVST_A is a
master conversion start that resets the internal state machine and causes the data output to start with the result
of channel A0. In cases where channel pairs of the device are used at different data rates, CONVST_A should
always be the one used at the highest frequency.
A conversion start must not be issued during an ongoing conversion on the corresponding channel pair. It is
allowed to initiate conversions on the other input pairs, however.
If a parallel interface is used, the content of the output port depends on which CONVST_x signals have been
issued. Figure 36 shows examples of different scenarios with all channel pairs active.
BUSY
(C27 = C26 = 0)
CS
CONVST_A, C
CONVST_B, D
RD
CH
A0
DB[15:0]
CH
A1
CH
B0
CH
B1
CH
C0
CH
C1
CH
D0
Old Data
CH
D1
Old Data
CONVST_B
CONVST_A, C, D
RD
CH
A0
DB[15:0]
CH
A1
Old Data
CH
B0
CH
B1
CH
C0
CH
C1
CH
D0
CH
D1
Old Data
Figure 36. Data Output versus CONVST_x (All Channels Active)
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
27
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
BUSY/INT
The BUSY signal indicates if a conversion is in progress. It goes high with a rising edge of any CONVST_x
signal and goes low when the output data of the last channel pair are available in the respective output register.
The readout of the data can be initiated immediately after the falling edge of BUSY.
In contrary, the INT signal goes high when a new conversion result has been loaded in the output register (this is
when the conversion has been completed) and remains high until the next read access, as shown in Figure 37.
The polarity of the BUSY/INT signal can be changed using CONFIG bit C26. The mode of pin 35 can be
controlled using CONFIG bit C27.
CONVST_x
tCONV
BUSY
(C27 = C26 = 0)
PAR = RD
SER = FS
INT
(C27 = 1, C26 = 0)
Figure 37. BUSY versus INT Behavior of Pin 35
Reference
The ADS8528/48/68 provides an internal, low-drift, 2.5V reference source. To increase the input voltage range,
the reference voltage can be switched to 3V mode using the VREF bit (CONFIG bit C13). The reference feeds a
10-bit string-DAC controlled by bits REFDAC[9:0] in the Configuration (CONFIG) Register. The buffered DAC
output is connected to the REFIO pin. In this way, the voltage at this pin is programmable in 2.44mV (2.92mV in
3V mode) steps and adjustable to the applications needs without additional external components. The actual
output voltage can be calculated using Equation 3:
Range ´ (Code + 1)
VREF =
1024
(3)
where:
Range = the chosen maximum reference voltage output range (2.5V or 3V),
Code = the decimal value of the DAC register content.
Table 4 lists some examples of internal reference DAC settings with a reference range set to 2.5V. However, to
ensure proper performance, the DAC output voltage should not be programmed below 0.5V.
The buffered output of the DAC should be decoupled with a 100nF capacitor (minimum); for best performance, a
470nF capacitor is recommended. If the internal reference is placed into power-down (default), an external
reference voltage can drive the REFIO pin.
Table 4. DAC Settings Examples (2.5V Operation)
28
VREFOUT
DECIMAL CODE
BINARY CODE
HEXADECIMAL CODE
0.5 V
204
00 1100 1100
CCh
1.25 V
511
01 1111 1111
1FFh
2.5 V
1023
11 1111 1111
3FFh
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
The voltage at the REFIO pin is buffered with four internal amplifiers, one for each ADC pair. The output of each
buffer must be decoupled with a 10µF capacitor between the pin pairs 3 and 6, 43 and 46, 50 and 53, and 60
and 63. The 10µF capacitors are available as ceramic 0805-SMD components and in X5R quality.
The internal reference buffers can be powered down to decrease the power dissipation of the device. In this
case, external reference drivers can be connected to the REFAP, REFBP, REFCP, and REFDP pins. With 10µF
decoupling capacitors, the minimum required bandwidth can be calculated using Equation 4:
ln(2)
f3dB =
2ptCONV
(4)
With the minimum tCONV of 1.33µs, the external reference buffers require a minimum bandwidth of 83kHz.
DIGITAL
This section describes the digital control and the timing of the device in detail.
Device Configuration
Depending on the desired mode of operation, the ADS8528/48/68 can be configured using the external pins
and/or the Configuration Register (CONFIG), as shown in Table 5.
Table 5. ADS8528/48/68 Configuration Settings
INTERFACE MODE
HARDWARE MODE (HW/SW = 0)
SOFTWARE MODE (HW/SW = 1)
Parallel (PAR/SER = 0)
Configuration using pins and (optionally) Configuration Configuration using Configuration Register bits C[31:0]
Register bits C30, C29, C[27:26], C22, C20, C18, C14, only; status of pins 9, 11, 20, and 34 are disregarded
C13, and C[9:0]
(if C29 = C28 = 0)
Serial (PAR/SER = 1)
Configuration using pins and (optionally) Configuration Configuration using Configuration Register bits C[31:0]
Register bits C30, C29, C[27:26], C22, C20, C18, C13, only; status of pins 9, 11, 20, and 34 are disregarded
and C[9:0]
(if C29 = C28 = 0)
Hardware Mode
With the HW/SW input (pin 41) set low, the device functions are controlled via the pins and, optionally,
Configuration Register bits C30, C29, C[27:26], C22, C20, C18, C14 (in parallel interface mode only), C13, and
C[9:0].
It is possible to generally use the part in hardware mode but to switch it into software mode to initialize or adjust
the Configuration Register settings (for example, the internal reference DAC) and back to hardware mode
thereafter.
Software Mode
When the HW/SW input is set high, the device operates in software mode with functionality set only by the
Configuration Register bits (corresponding pin settings are ignored).
If parallel interface is used, an update of all Configuration Register settings is performed by issuing two 16-bit
write accesses on pins DB[15:0] (to avoid loosing data, the entire sequence must be finished before starting a
new conversion). CS should be held low during these two accesses. To enable the actual update of the register
settings, the first bit (C31) must be set to '1' during the access.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
29
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
If the serial interface is used, the update of the register contents can be performed continuously (combined
read/write access). Optionally, to reduce the data transfer on the SDI line and the electromagnetic interference
(EMI) of the system, the SDI input can be pulled low when a register update is not required. Figure 38 illustrates
the different Configuration Register update options.
RESET
(or Power Up)
BUSY
(C20 = C21 = 0)
PAR/SER = 1
FS
Content Update
C[31:0]
Initialization Data
SDI
No Content Update
C[31:0]
PAR/SER = 0
CS
WR
Update
Initialization Data
DB[15:0]
C
[31:16]
C
[15:0]
C
[31:16]
C
[15:0]
Figure 38. Configuration Register Update Options
30
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
Configuration (CONFIG) Register
The Configuration Register settings can only be changed in software mode and are not affected when switching
to hardware mode thereafter. The register values are independent from input pin settings. Changes are active
with the second rising edge of WR in parallel interface mode or with the 32nd SCLK falling edge of the access in
which the register content has been updated in serial mode. The CONFIG content is defined in Table 6.
Table 6. CONFIG: Configuration Register (Default: 000003FFh)
31
30
29
28
27
26
25
24
WRITE_EN
READ_EN
CLKSEL
CLKOUT
BUSY/INT
BUSY POL
STBY
RANGE_A
23
22
21
20
19
18
17
16
RANGE_B
PD_B
RANGE_C
PD_C
RANGE_D
PD_D
Don't care
Don't care
15
14
13
12
11
10
9
8
REFEN
REFBUF
VREF
Don't care
Don't care
Don't care
D9
D8
7
6
5
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
Bit 31
WRITE_EN: Register update enable
This bit is not active in hardware mode.
0 = Register content update disabled (default)
1 = Register content update enabled
Bit 30
READ_EN: Register read-out access enable
This bit is not active in hardware mode.
0 = Normal operation (conversion results available on SDO_A)
1 = Configuration Register contents output on SDO_A with next two accesses
(READ_EN automatically resets to '0' thereafter)
Bit 29
CLKSEL: Conversion clock selector
This bit is active in hardware mode.
0 = Normal operation with internal conversion clock; mandatory in hardware mode (default)
1 = External conversion clock applied through pin 34 (XCLK) is used (conversion takes 19
clock cycles)
Bit 28
CLKOUT: Internal conversion clock output enable
This bit is not active in hardware mode.
0 = Normal operation (default)
1 = Internal conversion clock is available at pin 34
Bit 27
BUSY/INT: Busy/interrupt selector
This bit is active in hardware mode.
0 = BUSY/INT pin in BUSY mode (default)
1 = BUSY/INT pin in interrupt mode (INT); can only be used if all eight channels are
sampled simultaneously (all CONVST_x tied together)
Bit 26
BUSY POL: BUSY/INT polarity selector
This bit is active in hardware mode.
0 = BUSY/INT active high (default)
1 = BUSY/INT active low
Bit 25
STBY: Power-down enable
This bit is not active in hardware mode.
0 = Normal operation (default)
1 = Entire device is powered down (including the internal clock and reference)
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
31
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
Bit 24
www.ti.com
RANGE_A: Input voltage range selector for channel pair A
This bit is not active in hardware mode.
0 = Input voltage range: 4VREF (default)
1 = Input voltage range: 2VREF
Bit 23
RANGE_B: Input voltage range selector for channel pair B
This bit is not active in hardware mode.
0 = Input voltage range: 4VREF (default)
1 = Input voltage range: 2VREF
Bit 22
PD_B: Power-down enable for channel pair B
This bit is active in hardware mode.
0 = Normal operation (default)
1 = Channel pair B is powered down
Bit 21
RANGE_C: Input voltage range selector for channel pair C
This bit is not active in hardware mode.
0 = Input voltage range: 4VREF (default)
1 = Input voltage range: 2VREF
Bit 20
PD_C: Power-down enable for channel pair C
This bit is active in hardware mode.
0 = Normal operation (default)
1 = Channel pair C is powered down
Bit 19
RANGE_D: Input voltage range selector for channel pair D
This bit is not active in hardware mode.
0 = Input voltage range: 4VREF (default)
1 = Input voltage range: 2VREF
Bit 18
PD_D: Power-down enable for channel pair D
This bit is active in hardware mode.
0 = Normal operation (default)
1 = Channel pair D is powered down
Bits[17:16]
Not used (default = 0)
Bit 15
REF_EN: Internal reference enable
This bit is not active in hardware mode.
0 = Internal reference source disabled (default)
1 = Internal reference source enabled
Bit 14
REFBUF: Internal reference buffers disable
This bit is active in hardware mode if the parallel interface is used.
0 = Internal reference buffers enabled (default)
1 = Internal reference buffers disabled
Bit 13
VREF: Internal reference voltage selector
This bit is active in hardware mode.
0 = Internal reference voltage set to 2.5V (default)
1 = Internal reference voltage set to 3.0V
Bits[12:10]
Not used (default = 0)
Bits[9:0]
D[9:0]: REFDAC setting bits
These bits are active in hardware mode.
These bits correspond to the settings of the internal reference DACs (compare to the
Reference section). Bit D9 is the MSB of the DAC. Default value is 3FFh (2.5V, nom).
32
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
Parallel Interface
To use the device with the parallel interface, the PAR/SER pin should be held low. The maximum achievable
data throughput rate is 650kSPS for the ADS8528, 600kSPS for the ADS8548, and 510kSPS for the ADS8568 in
this case.
Access to the ADS8528/48/68 is controlled as illustrated in Figure 2 and Figure 3.
Serial Interface
The serial interface mode is selected by setting the PAR/SER pin high. In this case, each data transfer starts with
the falling edge of the frame synchronization input (FS). The conversion results are presented on the serial data
output pins SDO_A (always active), SDO_B, SDO_C, and SDO_D, depending on the selections made using the
SEL_xx pins. Starting with the most significant bit (MSB), the output data are changed with the falling edge of
SCLK. Output data of the ADS8528 and ADS8548 maintain the LSB-aligned 16-bit format with leading bits
containing the extended sign (see also Table 7). Serial data input SDI are latched with the falling edge of SCLK.
The serial interface can be used with one, two, or four output ports. Port SDO_B can be enabled using pin 27
(SEL_B) while ports SDO_C and SDO_D are enabled using pin 28 (SEL_CD). If all four serial data output ports
are selected, the data can be read with either two 16-bit data transfers or with a single 32-bit data transfer. The
data of channels CH_x0 are available first, followed by data from channels CH_x1. The maximum achievable
data throughput rate is 480kSPS for the ADS8528, 450kSPS for the ADS8548, and 400kSPS for the ADS8568 in
this case.
If the application allows a data transfer using two ports only, the SDO_A and SDO_B outputs are used. The
device outputs data from channel CH_A0 followed by CH_A1, CH_C0, and CH_C1 on SDO_A, while data from
channel CH_B0 followed by CH_B1, CH_D0, and CH_D1 occur on SDO_B. In this case, a data transfer of four
16-bit words, two 32-bit words, or one continuous 64-bit word is supported. The maximum achievable data
throughput rate is 360kSPS for the ADS8528, 345kSPS for the ADS8548, and 315kSPS for the ADS8568 in this
case.
The output SDO_A is always active and exclusively used if only one serial data port is used in the application.
The data are available in the following order: CH_A0, CH_A1, CH_B0, CH_B1, CH_C0, CH_C1, CH_D0, and
CH_D1. Data can be read using eight 16-bit transfers, four 32-bit transfers, two 64-bit transfers, or a single
128-bit transfer. The maximum achievable data throughput rate is 235kSPS for the ADS8528, 230kSPS for the
ADS8548 and 215kSPS for the ADS8568 in this case. Figure 1 and Figure 39 show all possible scenarios in
more detail.
BUSY
(C20 = C21 = 0)
SEL_B = 1, SEL_C/D = 0
64 SCLKs
FS
SDO_A
CHA0 CHA1 CHC0 CHC1
SDO_B
CHB0 CHB1 CHD0 CHD1
SEL_B = SEL_C/D = 0
128 SCLKs
FS
SDO_A
CHA0 CHA1 CHB0 CHB1 CHC0 CHC1 CHD0 CHD1
Figure 39. Data Output with One or Two Active SDOs (All Input Channels Active and Converted)
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
33
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
Daisy-Chain Mode
The serial interface of the ADS8528/48/68 supports a daisy-chain feature that allows cascading of multiple
devices to minimize the board space requirements and simplify routing of the data and control lines. In this case,
pins DB3/DCIN_A, DB2/DCIN_B, DB1/DCIN_C, and DB0/DCIN_D are used as serial data inputs for channels A,
B, C, and D, respectively. Figure 40 shows an example of a daisy-chain connection of three devices sharing a
common CONVST line to allow simultaneous sampling of 24 analog channels along with the corresponding
timing diagram.
To activate the daisy-chain mode, the DCEN pin must be pulled high. However, the DCEN of the first device in
the chain must remain low.
In applications in which not all channel pairs are used, it is recommended to declare the part with disabled
channel pair(s) to be the first in the daisy-chain.
CONVST
FS
SCLK
ADS85x8
#1
ADS85x8
#2
ADS85x8
#3
CONVST_A/B/C/D
CONVST_A/B/C/D
CONVST_A/B/C/D
FS
FS
FS
SCLK
SCLK
SCLK
SDO_A
SDO_A
DCIN_A
SDO_A
DCIN_A
SDO_B
DCIN_B
SDO_B
DCIN_B
SDO_B
SDO_C
DCIN_C
SDO_C
DCIN_C
SDO_C
DCIN_D
SDO_D
DCIN_D
SDO_D
SDO_D
DVDD
DCEN
To
Processing
Unit
DVDD
DCEN
DCEN
DGND
CONVST
BUSY
(C27 = C26 = 0)
FS
SDO_x #3
Don’t Care
16-Bit Data CHx0
ADS85x8 #3
16-Bit Data CHx1
ADS85x8 #3
16-Bit Data CHx0
ADS85x8 #2
16-Bit Data CHx1
ADS85x8 #2
16-Bit Data CHx0
ADS85x8 #1
16-Bit Data CHx1
ADS85x8 #1
Figure 40. Example of Daisy-Chaining Three Devices
34
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
Output Data Format
The data output format of the ADS8528/48/68 is binary twos complement, as shown in Table 7. For the
ADS8528/48 (which deliver 12-bit or 14-bit conversion results, respectively), the leading bits of either the 16-bit
frame (serial interface) or the output pins (DB[15:12] for the ADS8528 or DB[15:14] for the ADS8548 in parallel
mode) deliver a sign extension.
Table 7. Output Data Format
BINARY CODE HEXADECIMAL CODE
DESCRIPTION
INPUT VOLTAGE VALUE
ADS8528
ADSS8548
ADS8568
Positive full-scale
+4VREF or +2VREF
0000 0111 1111 1111
07FFh
0001 1111 1111 1111
1FFFh
0111 1111 1111 1111
7FFFh
Midscale +0.5LSB
VREF/(2 × resolution)
0000 0000 0000 0000
0000h
0000 0000 0000 0000
0000h
0000 0000 0000 0000
0000h
Midscale –0.5LSB
–VREF/(2 × resolution)
1111 1111 1111 1111
FFFFh
1111 1111 1111 1111
FFFFh
1111 1111 1111 1111
FFFFh
Negative full-scale
–4VREF or –2VREF
1111 1000 0000 0000
F800h
1110 0000 0000 0000
E000h
1000 0000 0000 0000
8000h
Reset and Power-Down Modes
The device supports two reset mechanisms: a power-on reset (POR) and a pin-controlled reset (RESET) that
can be issued using pin 10. Both, the POR and RESET act as a master reset that causes any ongoing
conversion to be interrupted, the Configuration Register content to be set to the default value, and all channels to
be switched into the sample mode.
When the device is powered up, the POR sets the device in default mode when AVDD reaches 1.2V. In normal
operation, glitches on the AVDD supply below this threshold trigger a device reset.
The entire device, except for the digital interface, can be powered down by pulling the STBY pin low (pin 9). As
the digital interface section remains active, data can be retrieved while in stand-by mode. To power the part on
again, the STBY pin must be brought high. The device is ready to start a new conversion after the 10ms required
to activate and settle the internal circuitry. This user-controlled approach can be used in applications that require
lower data throughput rates at lowest power dissipation. The content of CONFIG is not changed during stand-by
mode and it is not required to perform a reset after returning to normal operation.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
35
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
While the standby mode impacts the entire device, each device channel pair (except channel pair A, which as
the master channel pair, is always active) can also be individually switched off by setting the Configuration
Register bits C22, C20, and C18 (PD_x). If a certain channel pair is powered-down in this manner, the output
register is disabled as shown in Figure 41. When reactivated, the relevant channel pair requires 10ms to fully
settle before starting a new conversion.
BUSY
(C27 = C26 = 0)
CONVST_A/B/D
RD
CH
A0
DB[15:0]
CH
A1
CH
B0
CH
B1
CH
D0
CH
A0
CH
D1
CH
A1
Same Data (Reread)
CONVST_B
CONVST_A/D
RD
CH
A0
DB[15:0]
CH
A1
Old Data
CH
B0
CH
B1
CH
D0
CH
A0
CH
D1
Old Data
CH
A1
Old Data (Reread)
(1) Channel pair C disabled (PD_C = 1), CS = 0.
NOTE: Boxed areas indicate the minimum required frame to acquire all new conversion results. The read access might be interrupted,
thereafter.
Figure 41. Example of Data Output Order with Channel Pair C Powered Down(1)
36
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
The auto-sleep mode is enabled by pulling pin 36 (ASLEEP) high. If the auto-sleep mode is enabled, the
ADS8528/48/68 automatically reduce the current requirement to 7mA (IAVDD) after finishing a conversion; thus,
the end of conversion actually activates this power-down mode. Triggering a new conversion by applying a
positive CONVST_x edge puts the device back into normal operation, starts the acquisition of the analog input,
and automatically starts a new conversion 6 to 7 conversion clock cycles later, as shown in Figure 42. Therefore,
a complete conversion process takes 25 to 26 conversion clock cycles; thus, the maximum throughput rate in
auto-sleep mode is reduced to a maximum of 400kSPS for the ADS8528, 375kSPS for the ADS8548, and
330kSPS for the ADS8568 in serial interface mode. In parallel mode, the maximum data rates are 510kSPS for
the ADS8528, 470kSPS for the ADS8548 and 400kSPS for the ADS8568. If enabled, the internal reference
remains active during auto-sleep mode. Table 8 compares the analog current requirements of the device in
different modes.
ASLEEP
6tCCLK
CONVST_x
BUSY
ADC CH_x
ACQ
CONV
Power-Down
ACQ
CONV
Power-Down
Figure 42. Auto-Sleep Power-Down Mode
Table 8. Maximum Analog Current (IAVDD) Demand of the ADS85x8
OPERATIONA
L MODE
ANALOG
CURRENT
(IAVDD)
Normal
operation
12.5mA/ch pair
at maximum
data rate
Auto-sleep
1.75mA/ch pair
ENABLED/DIS
ABLED BY
ACTIVATED
BY
NORMAL
OPERATION
TO
POWERDOWN DELAY
RESUMED BY
POWER-UP
TO NORMAL
OPERATION
DELAY
POWER-UP
TO NEXT
CONVERSION
START TIME
CONVST_x
—
—
—
—
Each end of
conversion
At falling edge
of BUSY
CONVST_x
Immediate
7 × tCCLK max
PD_x = 1
(CONFIG bit)
Immediate
PD_x = 0
(CONFIG bit)
Immediate after
completing
CONFIG
update
10ms
STBY = 0
Immediate
STBY = 1
Immediate
10ms
Power on
Power off
ASLEEP = 1
ASLEEP = 0
HW/SW = 1
Power-down of
16µA
channel pair X (channel pair X)
Power-down
(entire device)
30µA
HW/SW = 0
Power on
Power off
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
37
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
APPLICATION INFORMATION
TYPICAL APPLICATION EXAMPLE
An example of a typical application of the ADS8528/48/68 is illustrated in Figure 43. In this case, the device is
used to simultaneously sample and convert the voltages and currents on three phases and the neutral line. In
this example, the BUSY signal is not used by the controller while the SW generates the required signals in timely
manner. TI’s OPA2211 is used as an input driver, supporting bandwidth that allows running the device at the
maximum data rate. However, because relatively low data rates are generally used in this type of applications,
the auto-sleep mode is activated in this example (ASLEEP is high) to minimize the current demand on the AVDD
and HVDD/HVSS power supplies. Further, the input drivers may not be necessary if the signal source fulfills the
requirements as defined by Equation 2. For example, at 10kSPS, the external drivers are not necessary if the
source impedance remains below 830kΩ in ±4VREF mode or 415kΩ in ±2VREF mode.
While the actual values of the resistors and capacitors depend on the bandwidth and performance requirements
of the application, for a data rate of 10kSPS, it is recommended to use a filter capacitor CF value of 1nF and a
series resistor RF of 10kΩ.
In applications supporting only single supply (for example, 5V), it is recommended to use the TPS65130 to
generate the bipolar supplies required by the ADC.
GROUNDING
All ground pins should be connected to a clean ground reference. This connection should be kept as short as
possible to minimize the inductance of these paths. It is recommended to use vias connecting the pads directly to
the corresponding ground plane. In designs without ground planes, the ground trace should be kept as wide and
as short as possible to reduce inductance. Avoid connections that are too close to the grounding point of a
microcontroller or digital signal processor.
Depending on the circuit density on the board, placement of the analog and digital components, and the related
current loops, a single solid ground plane for the entire printed circuit board (PCB) or dedicated analog and
digital ground areas may be used. In case of separated ground areas, ensure a low-impedance connection
between the analog and digital ground of the ADC by placing a bridge underneath (or next to) the ADC.
Otherwise, even short undershoots on the digital interface with a value of lower than –300mV lead to the
conduction of ESD diodes, causing current to flow through the substrate and either degrading the analog
performance or even damaging the part. It is recommended to use a common ground plane underneath the
device as a local ground reference for all xGND pins; see Figure 44. During PCB layout, care should be taken to
avoid any return currents crossing sensitive analog areas or signals.
38
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
R1
R2
AGND
HVDD
ADS85x8
RF
CH_A0
L1 Current
Signal
CF
OPA2211
L1 Voltage
Signal
AGND
CF
RF
CH_A1
REFAP
HVSS
10mF
AGND
R1
REFAN
AGND
R2
REFBN
AGND
10mF
HVDD
CONVST_A
CONVST_B
CONVST_C
REFBP
CONVST_D
RF
RESET
CH_B0
L2 Current
Signal
OPA2211
L2 Voltage
Signal
AGND
RD
CF
RF
Host
Controller
CS
CF
DB[15:0]
CH_B1
REFIO
HVSS
0.47mF
AGND
R1
AGND
R2
REFN
AGND
HVDD
DVDD
RF
CH_C0
L3 Current
Signal
STBY
CF
OPA2211
L3 Voltage
Signal
ASLEEP
AGND
CF
RF
REFEN/WR
CH_C1
HW/SW
PAR/SER
REFCP
HVSS
10mF
AGND
R1
RANGE
AGND
R2
REFCN
REFDN
AGND
DGND
10mF
HVDD
REFDP
RF
CH_D0
N Current
Signal
CF
OPA2211
N Voltage
Signal
AGND
CF
RF
DVDD
CH_D1
AVDD
6x
0.1mF
HVSS
AGND
R1
R2
AGND
10mF
AVDD
AVDD
AGND
AGND
AGND
AGND
AGND
AGND
AVDD
AVDD
AVDD
AVDD
AVDD
DVDD
1mF
DGND
DGND
HVSS
HVSS
0.1mF
10mF
0.1mF
10mF
AGND
HVDD
ADS85x8
HVDD
Figure 43. Three-Phase + N Current/Voltage Measurement Application Based on the ADS85x8
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
39
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
POWER SUPPLY
The ADS8528/48/68 require four separate supplies: an analog supply for the ADC (AVDD), the buffer I/O supply
for the digital interface (DVDD), and the high-voltage supplies driving the analog input circuitry (HVDD and
HVSS). Generally, there are no specific requirements with regard to the power sequencing of the device.
However, when HVDD is supplied before AVDD, the internal electrostatic discharge (ESD) structure conducts,
increasing the IHVDD beyond the specified value, until the AVDD is applied.
The AVDD supply provides power to the internal circuitry of the ADC. If run at maximum data rate, the IAVDD is
too high to allow use of a passive filter between the digital board supply of the application and the AVDD pins. A
linear regulator is recommended to generate the analog supply voltage. Each AVDD pin should be decoupled to
AGND with a 100nF ceramic capacitor. In addition, a single 10µF capacitor should be placed close to the device
but without compromising the placement of the smaller capacitors. Optionally, each supply pin can be decoupled
using a 1µF ceramic capacitor without the requirement for the additional 10µF capacitor.
The DVDD supply is only used to drive the digital I/O buffers and allows seamless interface with most
state-of-the-art processors and controllers. As a result of the low IDVDD value, a 10Ω series resistor can be used
on the DVDD pin to reduce the noise energy from the external digital circuitry influencing the performance of the
device. A bypass ceramic capacitor of 1µF (or alternatively, a pair of 100nF and 10µF capacitors) should be
placed between pins 24 and 25.
The high-voltage supplies (HVSS and HVDD) are connected to the analog inputs. These supplies are not
required to be of symmetrical nature with regard to AGND. Noise and glitches on these supplies directly couple
into the input signals. Place a 100nF ceramic decoupling capacitor, located as close to the device as possible,
between each of pins 1, 48, and AGND. An additional 10µF capacitor is used that should be placed close to the
device but without compromising the placement of the smaller capacitors.
Figure 44 shows a layout recommendation for the ADS8528/48/68 along with the proper decoupling and
reference capacitors placement and connections. The layout recommendation takes into account the actual size
of the components used.
40
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
Top View
RF
RF
RF
CF
CF
RF
CF
CF
10mF
RF
CF
0.1mF
To HVDD
HVSS
HVDD
CH_D1
CH_A1
REFDN
REFAN
AVDD
AVDD
AGND
AGND
REFDP
REFAP
CH_D0
CH_A0
8
41
10mF
40
39
11
38
12
37
13
36
CF
33
17
18
19
20
21
22
23
27
28
29
31
16
CF
RF
32
35
34
30
AVDD
AGND
26
LEGEND
Top Layer; Copper Pour and Traces
9
10
DVDD
RF
RF
10mF
DGND
CF
10mF
CH_B0
REFBP
AVDD
AGND
REFBN
REFN
CH_B1
REFIO
AVDD
AGND
CH_C1
AVDD
REFCN
AGND
CH_C0
Tto HVSS
REFCP
0.1mF
10mF
10mF
0.47mF
Lower Layer; AGND Area
Lower Layer; DGND Area
Via
(1) All AVDD/DVDD decoupling capacitors are placed on the bottom layer underneath the device power-supply pins and are connected by
vias. All 100nF ceramic capacitors are placed as close as possible to the device while the 10µF capacitors are also close but without
compromising the placement of the smaller capacitors.
Figure 44. Layout Recommendation
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
41
ADS8528
ADS8548
ADS8568
SBAS543A – AUGUST 2011 – REVISED OCTOBER 2011
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (August 2011) to Revision A
Page
•
Deleted INL column from Family/Ordering Information table ............................................................................................... 2
•
Changed DC Accuracy, INL parameter in ADS8568 Electical Chatacteristics table ............................................................ 5
42
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): ADS8528 ADS8548 ADS8568
PACKAGE OPTION ADDENDUM
www.ti.com
16-Nov-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
ADS8528SPM
ACTIVE
LQFP
PM
64
160
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8528SPMR
ACTIVE
LQFP
PM
64
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8528SRGCR
ACTIVE
VQFN
RGC
64
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8528SRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8548SPM
ACTIVE
LQFP
PM
64
160
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8548SPMR
ACTIVE
LQFP
PM
64
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8548SRGCR
ACTIVE
VQFN
RGC
64
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8548SRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8568SPM
ACTIVE
LQFP
PM
64
160
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8568SPMR
ACTIVE
LQFP
PM
64
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8568SRGCR
ACTIVE
VQFN
RGC
64
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ADS8568SRGCT
ACTIVE
VQFN
RGC
64
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
16-Nov-2011
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Nov-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ADS8528SPMR
LQFP
PM
64
1000
330.0
24.4
13.0
13.0
2.1
16.0
24.0
Q2
ADS8528SRGCR
VQFN
RGC
64
2000
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS8528SRGCT
VQFN
RGC
64
250
180.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS8548SPMR
LQFP
PM
64
1000
330.0
24.4
13.0
13.0
2.1
16.0
24.0
Q2
ADS8548SRGCR
VQFN
RGC
64
2000
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS8548SRGCT
VQFN
RGC
64
250
180.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS8568SPMR
LQFP
PM
64
1000
330.0
24.4
13.0
13.0
2.1
16.0
24.0
Q2
ADS8568SRGCR
VQFN
RGC
64
2000
330.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
ADS8568SRGCT
VQFN
RGC
64
250
180.0
16.4
9.3
9.3
1.5
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Nov-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS8528SPMR
LQFP
PM
64
1000
346.0
346.0
41.0
ADS8528SRGCR
VQFN
RGC
64
2000
346.0
346.0
33.0
ADS8528SRGCT
VQFN
RGC
64
250
210.0
185.0
35.0
ADS8548SPMR
LQFP
PM
64
1000
346.0
346.0
41.0
ADS8548SRGCR
VQFN
RGC
64
2000
346.0
346.0
33.0
ADS8548SRGCT
VQFN
RGC
64
250
210.0
185.0
35.0
ADS8568SPMR
LQFP
PM
64
1000
346.0
346.0
41.0
ADS8568SRGCR
VQFN
RGC
64
2000
346.0
346.0
33.0
ADS8568SRGCT
VQFN
RGC
64
250
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996
PM (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
0,08 M
33
48
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040152 / C 11/96
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Falls within JEDEC MS-026
May also be thermally enhanced plastic with leads connected to the die pads.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated