® AFE1144 AFE 114 4 For most current data sheet and other product information, visit www.burr-brown.com HDSL /MDSL ANALOG FRONT END ● 64kbps TO 1168kbps OPERATION ● SCALABLE DATA RATE FEATURES ● LOWER OUT OF BAND PSD ● 250mW POWER DISSIPATION ● +5V POWER (5V or 3.3V Digital) ● SSOP-28 ● PIN COMPATIBLE WITH AFE1124 DESCRIPTION Burr-Brown’s Analog Front End chip greatly reduces the size and cost of an xDSL (Digital Subscriber Line) system by providing all of the active analog circuitry needed to connect a digital signal processor to an external compromise hybrid and line transformer. The AFE1144 is optimized for HDSL (High bit rate DSL) and for lower speed MDSL (Medium speed DSL) and RADSL (Rate Adaptive DSL) applications. Because the transmit and receive filter responses automatically change with clock frequency, the AFE1144 is particularly suitable for RADSL and multiple rate DSL systems. The device operates over a wide range of data rates from 64kbps to 1168kbps. Functionally, this unit consists of a transmit and a receive section. The transmit section generates analog signals from 2-bit digital symbol data and filters the analog signals to create 2B1Q symbols. The on board differential line driver provides a 13.5dBm signal to the telephone line. The receive section filters and digitizes the symbol data received on the telephone line. This IC operates on a single 5V supply. The digital circuitry in the unit can be connected to a supply from 3.3V to 5V. It is housed in a SSOP-28 package. txLINE Pulse Former txLINE Line Driver tx and rx Control Registers tx and rx Interface Lines Difference Amplifier Decimation Filter rxHYB rxHYB ∆Σ Modulator rxLINE Programmable Gain Amp AFE1144 rxLINE Patents Pending International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1999 Burr-Brown Corporation SBWS013 PDS-1575A 1 Printed in U.S.A. December, 1999 AFE1144 SPECIFICATIONS Specifications are at 25°C, AVDD = +5V, DVDD = +3.3V, ftx = 584kHz (E1 rate), unless otherwise noted. AFE1144E PARAMETER RECEIVE CHANNEL Number of Inputs Input Voltage Range Common-Mode Voltage Input Impedance All Inputs Input Capacitance Input Gain Matching Resolution Programmable Gain Settling Time for Gain Change Gain + Offset Error Output Data Coding Output Symbol Rate, rxSYNC(3) Output Bit Rate, rxSYNC(3) TRANSMIT CHANNEL Transmit Clock Rate, ftx T1 Transmit –3dB Point T1 Rate Power(4, 5) E1 Transmit –3dB Point E1 Transmit Power(4, 5) Common-Mode Voltage, VCM Output Resistance(6) TRANSCEIVER PERFORMANCE Uncancelled Echo(5) DIGITAL INTERFACE Logic Levels VIH VIL VOH VOL trx1 Interface POWER Analog Power Supply Voltage Analog Power Supply Voltage Digital Power Supply Voltage Digital Power Supply Voltage Power Dissipation(4, 5) Power Dissipation(4, 5) PSRR COMMENTS MIN Differential Balanced Differential(1) 2 Line Input vs Hybrid Input 0dB, 3dB, 6dB, 9dB and 12dB Tested at Each Gain Range Two’s Complement TYP ±3.0 AVDD/2 See Typical Performance Curves 10 ±2 14 0 +12 6 5 32 64 Symbol Rate T1E1 4/99 - 002R4 Draft Compliant txBoost = 0 ETSI Compliant txBoost = 0 32 13 –71 –71 –74 –76 –78 –80 DVDD –1 –0.3 DVDD –0.5 TEMPERATURE RANGE Operating(6) –68.5 –68.5 –71 –73.5 –75.5 –77.5 dB dB dB dB dB dB DVDD +0.3 +0.8 V V V V ns +0.4 14 9 Specification Operating Range Specification Operating Range AVDD = 5V, DVDD = 3.3V, AVDD = DVDD = 5V kHz kHz dBm kHz dBm V Ω 14 rxGAIN = 0dB, Loopback Enabled rxGAIN = 0dB, Loopback Disabled rxGAIN = 3dB, Loopback Disabled rxGAIN = 6dB, Loopback Disabled rxGAIN = 9dB, Loopback Disabled rxGAIN = 12dB, Loopback Disabled 5 4.75 5.25 V V V V mW mW dB +85 °C 5.25 3.3 3.15 250 300 55 –40 pF % Bits dB Symbol Periods %FSR(2) 584 14 DC to 1MHz V V kHz kbits/sec 292 13 UNITS 584 1168 196 AVDD /2 1 |IIH| < 10µA |IIL| < 10µA IOH = –20µA IOL = 20µA MAX NOTES: (1) With a balanced differential signal, the positive input is 180° out of phase with the negative input, therefore the actual voltage swing about the commonmode voltage on each pin is ±1.5V to achieve a total input range of ±3.0V or 6Vp-p. (2) FSR is Full-Scale Range. (3) The output data is available at twice the symbol rate with interpolated values. (4) With a pseudorandom equiprobable sequence of HDSL pulses; 13.5dBm applied to the transformer (16.5dBm output from txLINEP and txLINEN). (5) See the Discussion of Specifications section of this data sheet for more information. (6) Funtionality is guaranteed over temperature range. ® AFE1144 2 PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS NC 1 28 NC NC 2 27 AGND DVDD 3 26 txLINE+ DGND 4 25 AVDD txbaudCLK 5 24 txLINE– tx48xCLK 6 23 AGND Data In 7 22 AVDD AFE1144 rxbaudCLK 8 21 vrREFN rx48xCLK 9 20 VCM Data Out 10 19 vrREFP DVDD 11 18 AGND DGND 12 17 rxLINE+ AVDD 13 16 rxLINE– rxHYB– 14 15 rxHYB+ Analog Inputs: Current .............................................. ±100mA, Momentary ±10mA, Continuous Voltage .................................. AGND –0.3V to AVDD +0.3V Analog Outputs Short Circuit to Ground (+25°C) ..................... Continuous AVDD to AGND ......................................................................... –0.3V to 6V DVDD to DGND ......................................................................... –0.3V to 6V Digital Input Voltage to DGND .................................. –0.3V to DVDD +0.3V Digital Output Voltage to DGND ............................... –0.3V to DVDD +0.3V AGND, DGND, Differential Voltage .................................................... 0.3V Junction Temperature (TJ) ............................................................. +150°C Storage Temperature Range .......................................... –40°C to +125°C Lead Temperature (soldering, 3s) .................................................. +260°C Power Dissipation .......................................................................... 700mW ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT AFE1144 " PACKAGE PACKAGE DRAWING NUMBER SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA SSOP-28 " 324 " –40°C to +85°C " AFE1144E " AFE1144E AFE1144E/1K Rails Tape and Reel NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of “AFE1144E/1K” will get a single 1000-piece Tape and Reel. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 AFE1144 PIN DESCRIPTIONS PIN # TYPE NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 No Connection No Connection Power Ground Input Input Input Input Input Output Power Ground Power Input Input Input Input Ground Output Output Output Power Ground Output Power Output Ground No Connection NC NC DVDD DGND txbaudCLK tx48xCLK Data In rxbaudCLK rx48xCLK Data Out DVDD DGND AVDD rxHYB– rxHYB+ rxLINE– rxLINE+ AGND vrREFP VCM vrREFN AVDD AGND txLINE– AVDD txLINE+ AGND NC DESCRIPTION Digital Supply (+3.3 to +5V) Digital Ground Transmit Baud Clock (584kHz for E1) Transmit Clock at 48x baud clock (28.032MHz for E1) Input Data Word Receive baud clock (584kHz for E1) Receive clock at 48x baud clock (28.032MHz for E1) Output Data Word Digital Supply (+3.3 to +5V) Digital Ground Analog Supply (+5V) Negative input from hybrid network Positive input from hybrid network Negative line input Positive line input Analog Ground Positive reference output Common-mode voltage (buffered) Negative reference output Analog Supply (+5V) Analog Ground Negative line output Output buffer supply (+5V) Positive line output Output buffer ground BLOCK DIAGRAM Pulse Former Filter Output Buffer txLINE– REFP txbaudCLK tx48xCLK txLINE+ Voltage Reference Transmit Control VCM REFN Data In rxbaudCLK rx48xCLK Receive Control rxLINE+ Data Out ∆Σ Modulator rxHYB+ rxHYB– Decimation Filter ® AFE1144 rxLINE– 4 TYPICAL PERFORMANCE CURVES At Output of HDSL Pulse Transformer The curves shown below are measured at the line output of the HDSL transformer. Typical at 25°C, AVDD+ = +5V, DVDD+ = +3.3V, fTX = 1168kHz, unless otherwise specified. POWER SPECTRAL DENSITY LIMIT - T1 RATE Power Spectral Density (dBm/Hz) 0 –20 –40 –60 –80 –100 –120 0 500 1000 1500 2000 2500 Frequency (kHz) CURVE 1. Upper Bound of Power Spectral Density Measured at Output of HDSL Transformer. INPUT IMPEDANCE vs BIT RATE Input Impedance (kΩ) 200 150 100 T1 = 784kbps, 32kΩ 50 E1 = 1168kbps, 21kΩ 0 100 300 500 700 900 1100 1300 Bit Rate (kbps) CURVE 2. Input Impedance of rxLINE and rxHYB. ® 5 AFE1144 THEORY OF OPERATION compromise hybrid (rxHYB). The connection of these two inputs so that the hybrid signal is subtracted from the line signal is described in the paragraph titled “Echo Cancellation in the AFE”. The equivalent gain for each input in the difference amp is one. The resulting signal then passes to a programmable gain amplifier which can be set for gains of 0dB through +12dB. Following the PGA, the ADC converts the signal to a 14-bit digital word. The AFE1144 consists of a transmit and a receive channel. It interfaces to the HDSL DSP through a six wire serial interface, three wires for the transmit channel and three wires for the receive channel. It interfaces to the HDSL telephone line transformer and external compromise hybrid through transmit and receive analog connections. The transmit channel consists of a switched-capacitor pulse forming network followed by a differential line driver. The pulse forming network receives 2-bit digital symbol data and generates a filtered 2B1Q analog output waveform. The differential line driver uses a composite output stage combining class B operation (for high efficiency driving large signals) with class AB operation (to minimize crossover distortion). The receive channel is designed around a fourth-order delta sigma A/D converter. It includes a difference amplifier designed to be used with an external compromise hybrid for first order analog echo cancellation. A programmable gain amplifier with gains of 0dB to +12dB is also included. The delta sigma modulator operating at a 24X oversampling ratio produces a 14-bit output at rates up to 584kHz (1.168Mbps). The serial interface consists of three wires for transmit and three wires for receive. The three wire transmit interface is transmit baud rate clock, transmit 48x oversampling clock and Data Out. The three wire receive interface is receive baud rate clock, receive 48x oversampling clock and Data In. The transmit and receive clocks are supplied to the AFE1144 from the DSP and are completely independent. DIGITAL DATA INTERFACE Data is received by the AFE1144 from the DSP on the Data In line. Data is transmitted from the AFE1144 to the DSP on the Data Out line. The paragraphs below describe the timing of these signals and data structure. Data is transmitted and received in synchronization with the 48x transmit and receive clocks (tx48xCLK and rx48xCLK). There are 48-bit times in each baud period. Data In is The receive channel operates by summing the two differential inputs, one from the line (rxLINE) and the other from the rxbaudCLK rx48xCLK Data Out HDSL DSP AFE1144 txbaudCLK tx48xCLK Data In FIGURE 1. DSP Interface. 4ns 4ns txbaudCLK from DSP A B 4ns tx48xCLK from DSP 4ns 48 Data In from DSP 1 2 3 4 MSB Bit 15 15 16 LSB Bit 0 47 48 1 MSB Bit 15 Transmit Timing Notes: (1) A baud period consists of 48 periods of the tx48xCLK. (2) The falling edge of the txbaudCLK can occur anywhere in area A. The rising edge can occur anywhere in area B. However, neither edge of the txbaudCLK can occur within 4ns (on either side) of any rising edge of tx48xCLK. (3) The AFE1144 reads Data In on the rising edge of the tx48xCLK. Data In must be stable at least 4ns before the rising edge of tx48xCLK and it must remain stable at least 4ns after the rising edge of tx48CLK. (4) Symbol data is transferred to the transmit pulse former after the LSB is read. The output analog symbol data reaches the peak of the symbol approximately 24 tx48xCLK periods later. FIGURE 2. Transmit Timing Diagram. ® AFE1144 6 received in the first 16 bits of each baud period. The remaining 32-bit periods are not used for Data In. Data Out is transmitted during the first 16 bits of the baud period. A second interpolated value is transmitted in subsequent bits of the baud period. be valid on the rising edge of the tx48xCLK. The AFE1144 reads Data In on the rising edge of the tx48xCLK. The bits are defined in Table I. Data In is read by the AFE1144 during the first 16 bits periods of each baud period. Only the first 8 bits are used in the AFE1144. The second 8 bits are reserved for use in the future products. The remaining 32 bits periods of the baud period are not used for Data In. txbaudCLK: The transmit data baud rate, generated by the DSP. It is 392kHz for T1 or 584kHz for E1. It may vary from 32kHz (64kbps) to 584kHz (1.168Mbps). Data In Bits: tx48xCLK: The transmit pulse former oversampling sampling clock, generated by the DSP. It is 48x the transmit symbol rate or 28.032MHz for 584kHz symbol rate. This clock should run continuously. tx enable signal—This bit controls the tx Symbol definition bits. If this bit is 0, only a 0 symbol is transmitted regardless of the state of the tx Symbol definition bits. If this bit is 1, the tx Symbol definition bits determine the output symbol. Data In: This is a 16-bit output data word sent from the DSP to the AFE. The sixteen bits include tx symbol information and other control bits, as described below. The data should be clocked out of the DSP on the falling edge and it should tx Symbol Definition—These two bits determine the output 2B1Q symbol transmitted. Rx Gain Settings—These bits set the gain of the receive channel programmable gain amplifier. MSB 1 LSB 2 3 1 1 8 Reserved tx Boost Loopback rx Gain tx Symbol tx Enable FIGURE 3. Data In Word. 4ns rxbaudCLK from DSP 4ns A B 4ns rx48xCLK from DSP Data Out from AFE1124 4ns 48 1 14 MSB Bit 15 15 16 17 23 24 LSB Bit 0 25 26 MSB Bit 15 39 40 47 48 1 MSB Bit 15 LSB Bit 0 trx1 Data 1 Interdata 8 Bits Data 1a Interdata 8 Bits Data 2 Receive Timing Notes: (1) A baud period consists of 48 periods of the tx48xCLK. (2) The falling edge of the rxbaudCLK can occur anywhere in area A. The rising edge can occur anywhere in area B. However, neither edge of the rxbaudCLK can occur within 4ns (on either side) of any rising edge of rx48xCLK. (3) For all data bits after the MSB of Data 1, the AFE1144 transfers Data Out on the falling edge of the rx48xCLK. The time from the falling edge of rx48xCLK until Data Out is stable is trx1. trx1 MIN MAX 9ns 14ns (4) The AFE1144 transfers the MSB of Data 1 on the falling edge of rxbaudCLK. If the falling edge of rxbaudCLK is synchronized with the falling edge of rx48xCLK, all of the Data Out bits will be the same width. In any case, the time from the falling edge of rxbaud CLK until the MSB of Data 1 is stable is trx1. FIGURE 4. Receive Timing Diagram. ® 7 AFE1144 DATA OUT PER SYMBOL PERIOD Loopback Control—This bit controls the operation of loopback. When enabled (logic 1), the rxLINE+ and rxline– inputs are disconnected from the AFE. The rxHYB+ and rxHYB– inputs remain connected. When disabled, the rxLINE+ and rxLINE– inputs are connected. txBoost—This bit controls the addition of 0.5dB additional power to the output line driver. BIT DESCRIPTION BIT STATE OUTPUT STATE 15 (MSB) tx Enable Signal 0 1 AFE Transmits a 0 Symbol AFE Transmits HDSL Symbol as defined by bits 14 and 13 14 and 13 tx Symbol Definition 00 –3 Transmit Symbol 01 11 10 –1 Transmit Symbol +1 Transmit Symbol +3 Transmit Symbol 000 001 010 011 100 101 110 111 rx gain in AFE 0dB rx gain in AFE 3dB rx gain in AFE 6dB rx gain in AFE 9dB rx gain in AFE 12dB rx gain in AFE Reserved rx gain in AFE Reserved rx gain in AFE Reserved 12 - 10 rx Gain Settings 9 Loopback Control 1 0 Loopback Mode Normal Operation 8 tx Boost 0 1 Normal Transmit Power +0.5dB Transmit Power Boost 7-0 SPARE BITS 16 Interdata Bits 8 Data 1a 16 Interdata bits 8 Total Bits/Symbol Period 48 MSB LSB 14 2 Reserved A/D Converter Data FIGURE 5. Data Out Word. ANALOG-TO-DIGITAL CONVERTER DATA The A/D converter data from the receive channel is coded in twos complement. ANALOG INPUT A/D CONVERTER DATA MSB NA TABLE I. Data In. rxbaudCLK: This is the receive data baud rate (symbol clock), generated by the DSP. It is 392kHz for T1 or 584kHz for E1. It can vary from 32kHz (64kbps) to 584kHz (1.168Mbps). LSB Positive Full Scale 01111111111111 Mid Scale 00000000000000 Negative Full Scale 10000000000000 ECHO CANCELLATION IN THE AFE The rxHYB input is subtracted from the rxLINE input for first order echo cancellation. For correct operation, be certain that the rxLINE input is connected to the same polarity signal at the transformer (+ to + and – to –) while the rxHYB input is connected to opposite polarity through the compromise hybrid (– to + and + to –) as shown in the Basic Connection Diagram. rx48xCLK: This is the A/D converter over-sampling clock, generated by the DSP. It is 48x the receive symbol rate or 28.032MHz for 584kHz symbol rate. This clock should run continuously. Data Out: This is the 14-bit A/D converter output data (+2 spare bits) sent from the AFE to the DSP. The 14 bits from the A/D Converter will be the upper bits of the 16-bit word (bits 15-2). The spare bits (1 and 0) will be always be low. Eight additional (interdata) bits follow which are always high. The data is clocked out on the falling edge of rx48xCLK. The bandwidth of the A/D converter decimation filter is equal to one half of the symbol rate. The nominal output rate of the A/D converter is one conversion per symbol period. For more flexible post processing, there is a second interpolated A/D conversion available in each symbol period. In Figure 4, the first conversion is shown as Data 1 and the second conversion is shown as Data 1a. It is suggested that rxbaudCLK is used with the rx48xCLK to read Data 1 while Data 1a is ignored. However, either or both outputs may be used for more flexible post-processing. SCALABLE TIMING The AFE1144 scales operation with the clock frequency. All internal filters and the pulse former change frequency with the clock speed so that the unit can be used at different frequencies just by changing the clock speed. For the receive channel, the digital filtering of the delta sigma converter scales directly with the clock speed. The bandwidth of the converter’s decimation filter is always onehalf of the symbol rate. The only receive channel issue in changing baud rate is the passive single pole anti-alias filter (see the following section). For systems implementing a broad range of speeds, selectable cutoff frequencies for the passive anti-alias filter should be used. ® AFE1144 DATA Data 1 8 0.1µF REFP VCM 0.1µF 0.1µF REFN 1:2 Transformer 13Ω Tip txLINE+ 0.01µF 13Ω txLINE– Ring – Input Antialias Filter fc ≅ 2 x Symbol Rate 750Ω rxbaudCLK + 0.01µF Compromise Hybrid – + rxHYB+ rx48xCLK Data Out HDSL DSP AFE1144 100pF txbaudCLK tx48xCLK 750Ω Data In rxHYB– 750Ω rxLINE– 100pF GNDA 750Ω GNDA rxLINE+ GNDA DVDD DVDD AVDD AVDD AVDD 5V to 3.3V Digital 5V Analog 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 1 - 10µF FIGURE 6. Basic Connection Diagram. For the transmit channel, the pulse shape and the power spectral density scale directly with the clock rate. The power spectral density shown in Curve 1 and the pulse template shown in Curve 2 are measured at the output of the transformer. The transformer and the RC circuit on the output provide some smoothing for the output transmission. At lower bit rates, the amount of smoothing will be less. for the rxLINE and rxHYB differential inputs should be approximately 1MHz for T1 and E1 symbol rates. Suggested values for the filter are 750Ω for each of the two input resistors and 100pF for the capacitor. Together the two 750Ω resistors and the 100pF capacitor result in a 3dB frequency of just over 1MHz. The 750Ω input resistors will result in minimal voltage divider loss with the input impedance of the AFE1144. RXHYB AND RXLINE INPUT ANTI-ALIASING FILTERS An external input anti-aliasing filter is needed on the hybrid and line inputs as shown in the Basic Connection Diagram above. The –3dB frequency of the input anti-aliasing filter The antialiasing filters will give best performance with 3dB frequency approximately equal to the bit rate. For instance, a 3dB frequency of 320kHz may be used for a single line bit rate of 320k bits per second. ® 9 AFE1144 DISCUSSION OF SPECIFICATIONS UNCANCELLED ECHO A key measure of transceiver performance is uncancelled echo. Uncancelled echo is the summation of all of the errors in the transmit and receive paths of the AFE1144. It includes effects of linearity, distortion and noise. Uncancelled echo is tested in production by Burr-Brown with a circuit that is similar to the one shown in Figure 7, Uncancelled Echo Test Diagram. DVDD (V) TYPICAL POWER DISSIPATION IN THE AFE1144 (mW) 584 (E1) 584 (E1) 392 (T1) 392 (T1) 146 (E1/4) 146 (E1/4) 3.3 5 3.3 5 3.3 5 250 300 240 270 230 245 TABLE II. Typical Power Dissipation. circuit uses a 1:2 transformer. The power measurements shown in Table II use an equivalent resistive load instead of the transformer to eliminate frequency dependent impedances of the transformer. The measurement of uncancelled echo is made as follows. The AFE is connected to an output circuit including a typical 1:2 line transformer. The line is simulated by a 135Ω resistor. Symbol sequences are generated by the tester and applied both to the AFE and to the input of an adaptive filter. The output of the adaptive filter is subtracted from the AFE output to form the uncanceled echo signal. Once the filter taps have converged, the RMS value of the uncancelled echo is calculated. Since there is no far-end signal source or additive line noise, the uncanceled echo contains only noise and linearity errors generated in the transmit and receive sections of the AFE1144. LAYOUT The analog front end of an HDSL system has two conflicting requirements. It must accept and deliver moderately high rate digital signals and it must generate, drive, and convert precision analog signals. To achieve optimal system performance with the AFE1144, both the digital and the analog sections must be treated carefully in board layout design. The data sheet value for uncancelled echo is the ratio of the RMS uncanceled echo (referred to the receiver input through the receiver gain) to the nominal transmitted signal (13.5dBm into 135Ω, or 1.74Vrms). This echo value is measured under a variety of conditions: with loopback enabled (line input disconnected); with loopback disabled under all receiver gain ranges; and with the line shorted (S1 closed in Figure 7). The power supply for the digital section of the AFE1144 can range from 3.3V to 5V. This supply should be decoupled to digital ground with ceramic 0.1µF capacitors placed as close to DGND and DVDD as possible. One capacitor should be placed between pins 3 and 4 and the second capacitor between pins 11 and 12. Ideally, both a digital power supply plane and a digital ground plane should run up to and underneath the digital pins of the AFE1144 (pins 5 through 10). However, DVDD may be supplied by a wide printed circuit board (PCB) trace. A digital ground plane underneath all digital pins is strongly recommended. POWER DISSIPATION Approximately 80% of the power dissipation in the AFE1144 is in the analog circuitry, and this component does not change with clock frequency. However, the power dissipation in the digital circuitry does decrease with lower clock frequency. In addition, the power dissipation in the digital section is decreased when operating from a smaller supply voltage, such as 3.3V. (The analog supply, AVDD, must remain in the range 4.75V to 5.25V). The remaining portion of the AFE1144 should be considered analog. All AGND pins should be connected directly to a common analog ground plane and all AVDD pins should be connected to an analog 5V power plane. Both of these planes should have a low impedance path to the power supply. The analog power supply pins should be decoupled to analog ground with ceramic 0.1µF capacitors placed as close to the AFE1144 as possible. One 10µF tantalum capacitor should also be used with each AFE1144 between the analog supply and analog ground. The power dissipation listed in the specifications section applies under these normal operating conditions: 5V Analog Power Supply; 3.3V Digital Power Supply; standard 13.5dBm delivered to the line; and a pseudorandom equiprobable sequence of HDSL output pulses. The power dissipation specifications includes all power dissipated in the AFE1144, it does not include power dissipated in the external load. The external power is 16.5dBm: 13.5dBm to the line and 13.5dBm to the impedance matching resistors. The external load power of 16.5dBm is 45mW. The typical power dissipation in the AFE1144 under various conditions is shown in Table II. Ideally, all ground planes and traces and all power planes and traces should return to the power supply connector before being connected together (if necessary). Each ground and power pair should be routed over each other, should not overlap any portion of another pair, and the pairs should be separated by a distance of at least 0.25 inch (6mm). One exception is that the digital and analog ground planes should be connected together underneath the AFE1144 by a small trace. The T1 and E1 power measurements in the Specifications are made with the output circuit shown in Figure 7. This ® AFE1144 BIT RATE PER AFE1144 (Symbols/sec) 10 13Ω Transmit Data txDATP 1:2 5.6Ω txLINEP 13Ω 5.6Ω 135Ω S1 txLINEN 1.5kΩ rxHYBP 3kΩ 100pF Adaptive Filter AFE1144 rxHYBN 1.5Ω 750Ω rxLINEP 100pF rxLINEN 750Ω Uncancelled Echo rxD13 - rxD0 FIGURE 7. Uncancelled Echo Test Diagram. ® 11 AFE1144 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated