ASW208 5-6000 MHz MMIC Amplifier Features Description ·19 dB Gain at 2 GHz The ASW208, a gain block amplifier MMIC, has a low noise, high gain, and high linearity over a wide range of frequency, being suitable for use in both receiver and transmitter of telecommunication systems up to 6 GHz. The amplifier is available in an SOT-89 package and passes through the stringent DC, RF, and reliability tests. ·22 dBm P1dB at 2 GHz ·35 dBm Output IP3 at 2 GHz ·1.7 dB NF at 2 GHz ·MTTF > 100 Years ·Single Supply ASW208 Package Style: SOT-89 Typical Parameters PerFrequency Application Circuit Typical Units MHz 50 900 2000 2700 3000 Gain dB 21 21 19 17 16.2 S11 dB -9 -14 -12 -11 -13 S22 dB -18 -12 -12 -12 -11 Output IP31) dBm 321) 372) 352) 332) 293) ·IF / 50 ~ 450 MHz (5 V) Noise Figure dB 5.2 1.6 1.7 1.9 2.4 ·3000 ~ 4500 MHz (5 V) Output P1dB dBm 23 22 22 21 20 ·SMATV / 950 ~ 2150 MHz (5.5 V) Current mA 80 80 80 80 80 V 5.5 5.5 5.5 5.5 5 Device Voltage ·500 ~ 3500 MHz (5.5 V) ·500 ~ 3500 MHz (5 V) ·IF / 50 ~ 450 MHz (5.5 V) ·SMATV / 950 ~ 2150 MHz (5 V) ·50 ~ 2600 MHz (5 V, 75ohm) 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1 MHz. 3) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. ·1000 ~ 2600 MHz (5 V, 45mA , 75ohm) Product Specifications Parameters Testing Frequency Units Min MHz Typ 2000 Gain dB 18 19 S11 dB -9 -12 S22 dB -9 -12 dBm 32 Output IP3 35 Noise Figure dB Output P1dB dBm 20.5 22 Current mA 60 80 Device Voltage V Max 1.7 2.0 100 Pin Configuration 5.5 Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to +85°C Storage Temperature -40 to +150°C Device Voltage +6 V Operating Junction Temperature +150°C Input RF Power (Continuous) 22 dBm Pin No. Function 1 RF IN 2 GND 3 RF OUT / Bias * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/11 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASW208 Pxxxx Dimensions (In mm) MIN NOM MAX 1.40 1.50 1.60 0.89 1.04 1.20 0.36 0.42 0.48 0.41 0.47 0.53 0.38 0.40 0.43 4.40 4.50 4.60 1.40 1.60 1.75 3.64 --4.25 2.40 2.50 2.60 2.90 3.00 3.10 0.35 0.40 0.45 0.65 0.75 0.85 1.40 1.50 1.60 Pin No. Function 1 RF IN 2 GND 3 RF OUT / Bias Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260°C reflow 2/11 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 900 2000 2700 Magnitude S21 (dB) 21 19 17 Magnitude S11 (dB) -14 -12 -11 Magnitude S22 (dB) -12 -12 -12 21 Output P1dB (dBm) 22 22 500 ~ 3500 MHz Output IP31) (dBm) 37 35 33 +5.5 V Noise Figure (dB) 1.6 1.7 1.9 Device Voltage (V) 5.5 5.5 5.5 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5.5 V C4=1 mF C3=100 pF L1=27 nH C1=33 pF RF IN C2=33 pF RF OUT ASW208 L2=27 nH S-parameters & K-factor 25 0 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 500 1000 1500 2000 2500 3000 3500 -20 0 500 1000 Frequency (MHz) 0 2000 2500 3000 3500 2500 3000 3500 5 4 Stability Factor -5 S22 (dB) 1500 Frequency (MHz) -10 3 2 -15 1 -20 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 3/11 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 900 2000 2700 Magnitude S21 (dB) 21 19 17 Magnitude S11 (dB) -14 -11 -11 Magnitude S22 (dB) -12 -11 -10 21 Output P1dB (dBm) 22 22 500 ~ 3500 MHz Output IP31) (dBm) 37 35 33 +5 V Noise Figure (dB) 1.6 1.7 1.9 Device Voltage (V) 5 5 5 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5 V C4=1 mF C3=100 pF R1= 56 kW L1=27 nH C1=33 pF RF IN C2=33 pF RF OUT ASW208 L2=27 nH S-parameters & K-factor 25 0 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 500 1000 1500 2000 2500 3000 3500 -20 0 500 1000 Frequency (MHz) 0 2000 2500 3000 3500 2500 3000 3500 5 4 Stability Factor -5 S22 (dB) 1500 Frequency (MHz) -10 3 2 -15 1 -20 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 4/11 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier Frequency (MHz) 50 150 300 450 Magnitude S21 (dB) 21 20 20 19.5 Magnitude S11 (dB) -9 -14 -15 -15 Magnitude S22 (dB) -18 -18 -15 -15 IF Output P1dB (dBm) 23 23.5 23.5 23.5 50 ~ 450 MHz Output IP31) (dBm) 32 33 34 34 Noise Figure (dB) 5.2 3.4 3.2 3.2 Device Voltage (V) 5.5 5.5 5.5 5.5 Current (mA) 80 80 80 80 APPLICATION CIRCUIT +5.5 V 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5.5 V C4=1 mF C3=100 pF L1=1.2 mH C1=1 nF RF IN C2=1 nF RF OUT ASW208 R1=150 W 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 -15 -20 0 100 200 300 400 500 -25 0 100 200 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 -25 400 500 3 2 1 0 100 200 300 400 500 0 0 500 Frequency (MHz) 5/11 300 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier Frequency (MHz) 50 150 300 450 Magnitude S21 (dB) 21 20 19.5 19.5 Magnitude S11 (dB) -10 -14 -15 -15 Magnitude S22 (dB) -18 -18 -15 -15 IF Output P1dB (dBm) 22 22 22 22 50 ~ 450 MHz Output IP31) (dBm) 31 32 33 33 Noise Figure (dB) 4.0 3.2 3.2 3.2 APPLICATION CIRCUIT +5 V Device Voltage (V) 5 5 5 5 Current (mA) 80 80 80 80 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5 V C4=1 mF C3=100 pF R1=56 kW L1=1.2 mH C1=1 nF RF IN C2=1 nF RF OUT ASW208 R2=150 W 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 -15 -20 0 100 200 300 400 500 -25 0 100 200 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 400 500 3 2 1 0 100 200 300 400 500 0 0 500 Frequency (MHz) 6/11 300 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 3000 4500 Magnitude S21 (dB) 16.2 16.4 Magnitude S11 (dB) -13 -12 Magnitude S22 (dB) -11 -13 Output P1dB (dBm) 20 16.5 3000 ~ 4500 MHz Output IP31) (dBm) 29 27.5 +5 V Noise Figure (dB) 2.4 2.7 Device Voltage (V) 5 5 Current (mA) 80 80 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5 V D1=5.6V Zener Diode C5=1 mF C4=100 pF L1=6.8 nH R2=56 kW C1=3 pF RF IN C2=3 pF RF OUT ASW208 R1=390 W C3=0.5 pF 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 2000 -15 -20 2500 3000 3500 4000 4500 5000 5500 -25 2000 2500 Frequency (MHz) -5 4 Stability Factor 5 S22 (dB) -10 -15 -20 4000 4500 5000 5500 3 2 1 2500 3000 3500 4000 4500 5000 5500 0 0 1000 Frequency (MHz) 7/11 3500 Frequency (MHz) 0 -25 2000 3000 2000 3000 4000 5000 6000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT SMATV 950 ~ 2150 MHz +5.5 V Frequency (MHz) 950 1500 2150 Magnitude S21 (dB) 21 20 17.5 Magnitude S11 (dB) -14 -12 -11 Magnitude S22 (dB) -12 -12 -12 Output P1dB (dBm) 22 22 21 Output IP31) (dBm) 37 35 34 Noise Figure (dB) 1.6 1.7 1.8 Device Voltage (V) 5.5 5.5 5.5 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5.5 V C4=1 mF C3=100 pF L1=27 nH C1=33 pF RF IN C2=33 pF RF OUT ASW208 L2=27 nH S-parameters & K-factor 25 0 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 500 1000 1500 2000 2500 3000 3500 -20 0 500 1000 Frequency (MHz) 0 2000 2500 3000 3500 2500 3000 3500 5 4 Stability Factor -5 S22 (dB) 1500 Frequency (MHz) -10 3 2 -15 1 -20 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 8/11 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT SMATV 950 ~ 2150 MHz +5 V Frequency (MHz) 950 1500 2150 Magnitude S21 (dB) 21 20 18 Magnitude S11 (dB) -14 -11 -11 Magnitude S22 (dB) -12 -11 -10 Output P1dB (dBm) 22 22 21 Output IP31) (dBm) 37 35 34 Noise Figure (dB) 1.6 1.7 1.8 Device Voltage (V) 5 5 5 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=5 V C4=1 mF C3=100 pF R1= 56 kW L1=27 nH C1=33 pF RF IN C2=33 pF RF OUT ASW208 L2=27 nH S-parameters & K-factor 25 0 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 500 1000 1500 2000 2500 3000 3500 -20 0 500 1000 Frequency (MHz) 0 2000 2500 3000 3500 2500 3000 3500 5 4 Stability Factor -5 S22 (dB) 1500 Frequency (MHz) -10 3 2 -15 1 -20 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 9/11 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT 75 Ohm 50 ~ 2600 MHz +5 V 50 1300 2600 Magnitude S21 (dB) 21.8 20.0 17.0 Magnitude S11 (dB) -7 -8 -10 Magnitude S22 (dB) -7 -9 -15 Output P1dB (dBm) 21 21 20 Output IP31) (dBm) 28.0 31.0 33.5 Output IP21) (dBm) 29 46 49 Noise Figure (dB) 3.5 2.1 1.6 Device Voltage (V) 5 5 5 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. 2 Vs=5 V Board Layout (FR4, 40x40 mm , 0.8T) Schematic C4=1 mF C3=100 pF R1=5.6 kW L1=150 nH RF OUT RF IN ASW208 C1=1 nF C2=1 nF L2=270 nH R2=200 W S-parameters & K-factor 0 25 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 400 800 1200 1600 2000 2400 2800 -20 0 400 Frequency (MHz) 800 1200 1600 2000 2400 2800 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 400 800 1200 1600 2000 2400 2800 Frequency (MHz) 10/11 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012 ASW208 5-6000 MHz MMIC Amplifier APPLICATION CIRCUIT 75 Ohm 1000 ~ 2600 MHz +5 V Frequency (MHz) 1000 1800 2600 Magnitude S21 (dB) 19.7 18.4 16.9 Magnitude S11 (dB) -11 -8 -12 Magnitude S22 (dB) -8 -15 -14 Output P1dB (dBm) 21 23 20 Output IP31) (dBm) 30 24 31 Noise Figure (dB) 1.8 2.5 2.5 Device Voltage (V) 5 5 5 Current (mA) 45 45 45 1) OIP3 is measured with two tones at an output power of +7 dBm/tone separated by 1MHz. Vs=5 V Schematic 2 Board Layout (FR4, 40x40 mm , 0.8T) C7=1 mF C6=100 pF L1=68 nH RF IN C1=100 pF C2=100 pF C3=100 pF RF OUT ASW208 L2=33 nH C4=0.5 pF S-parameters & K-factor 0 25 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 -20 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 Frequency (MHz) 11/11 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2012