Features • Fast Read Access Time - 45 ns • Low-Power CMOS Operation • • • • • • • – 100 µA max. Standby – 25 mA max. Active at 5 MHz (AT27C010L) – 35 mA max. Active at 5 MHz (AT27C010) JEDEC Standard Packages – 32-Lead 600-mil PDIP – 32-Lead PLCC – 32-Lead TSOP 5V ± 10% Supply High Reliability CMOS Technology – 2000V ESD Protection – 200 mA Latchup Immunity Rapid™ Programming Algorithm - 100 µs/byte (typical) CMOS and TTL Compatible Inputs and Outputs Integrated Product Identification Code Commercial, Industrial and Automotive Temperature Ranges 1-Megabit (128K x 8) OTP EPROM AT27C010(L) Description The AT27C010(L) is a low-power, high-performance 1,048,576-bit one-time programmable read only memory (OTP EPROM) organized as 128K by 8 bits. They require only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 45 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems. Two power versions are offered. In read mode, the AT27C010 typically consumes 25 mA while the AT27C010L requires only 8 mA. Standby mode supply current for both parts is typically less than 10 µA. (continued) PLCC Top View Addresses O0 - O7 Outputs CE Chip Enable OE Output Enable PGM Program Strobe NC No Connect A7 A6 A5 A4 A3 A2 A1 A0 O0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC PGM NC A14 A13 A8 A9 A11 OE A10 CE O7 O6 O5 O4 O3 5 6 7 8 9 10 11 12 13 29 28 27 26 25 24 23 22 21 A14 A13 A8 A9 A11 OE A10 CE O7 1M bit EPROM TSOP Top View Type 1 PDIP Top View VPP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 GND 4 3 2 1 32 31 30 A0 - A16 14 15 16 17 18 19 20 Function O1 O2 GND O3 O4 O5 O6 Pin Name A12 A15 A16 VPP VCC PGM NC Pin Configurations A11 A9 A8 A13 A14 NC PGM VCC VPP A16 A15 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE O7 O6 O5 O4 O3 GND O2 O1 O0 A0 A1 A2 A3 Rev. 0321J–07/98 1 The AT27C010(L) in available in a choice of industry standard JEDEC-approved one-time programmable (OTP) plastic PDIP, PLCC, and TSOP packages. All devices feature two line control (CE, OE) to give designers the flexibility to prevent bus contention. With 128K byte storage capability, the AT27C010(L) allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. Atmel’s 27C010(L) have additional features to ensure high quality and efficient production use. The Rapid™ Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. Block Diagram 2 AT27C010(L) System Considerations Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the V CC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. AT27C010(L) Absolute Maximum Ratings* Temperature Under Bias ................................ -55°C to +125°C *NOTICE: Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .........................................-2.0V to +7.0V(1) Voltage on A9 with Respect to Ground ......................................-2.0V to +14.0V(1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. VPP Supply Voltage with Respect to Ground .......................................-2.0V to +14.0V(1) Note: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V dc which may overshoot to +7.0 volts for pulses of less than 20 ns. Operating Modes Mode\Pin CE OE PGM Ai VPP (1) Outputs Read VIL VIL X Ai X DOUT Output Disable X VIH X X X High Z VIH X X X X High Z VIL VIH VIL Ai VPP DIN PGM Verify VIL VIL VIH Ai VPP DOUT PGM Inhibit VIH X X X VPP High Z Standby Rapid Program (2) (3) Product Identification(4) Notes: VIL VIL X A9 = VH A0 = VIH or VIL A1 - A16 = VIL X Identification Code 1. X can be VIL or VIH. 2. Refer to Programming Characteristics. 3. VH = 12.0 ± 0.5V. 4. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte. 3 DC and AC Operating Conditions for Read Operation AT27C010/AT27C010L -45 -55 -70 -90 -12 -15 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 125°C -40°C - 125°C -40°C - 125°C 5V ± 10% 5V ± 10% 5V ± 10% Com. Operating Temp. (Case) Ind. Auto. 5V ± 10% VCC Power Supply 5V ± 10% 5V ± 10% DC and Operating Characteristics for Read Operation Symbol Parameter Condition ILI Input Load Current VIN = 0V to VCC ILO Output Leakage Current IPP1 (2) VPP (1)) Min Max Units Com., Ind. ±1 µA Auto. ±5 µA Com., Ind. ±5 µA Auto. ±10 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 100 µA 1 mA AT27C010(L) 25 mA AT27C010 35 mA VOUT = 0V to VCC Read/Standby Current ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage -0.6 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage IOL = 2.1 mA 0.4 V VOH Output High Voltage IOH = -400 µA Notes: ISB2 (TTL), CE = 2.0 to VCC + 0.5V f = 5 MHz, IOUT = 0 mA, CE = VIL 2.4 V 1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP.. 2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP.. AC Characteristics for Read Operation AT27C010/AT27C010L -45 Symbol Parameter Condition tACC(3) tCE Max Min -70 Max Min -90 Max Min -12 Max Min -15 Max Min Max Units Address to Output Delay CE = OE = VIL 45 55 70 90 120 150 ns (2) CE to Output Delay OE = VIL 45 55 70 90 120 150 ns (2)(3) OE to Output Delay CE = VIL 20 25 30 35 35 40 ns 20 20 25 25 30 35 ns tOE tDF(4)(5) OE or CE High to Output Float, whichever occurred first tOH Output Hold from Address, CE or OE, whichever occurred first Notes: 4 Min -55 7 2,3,4,5. - see AC Waveforms for Read Operation. AT27C010(L) 7 7 0 0 0 ns AT27C010(L) AC Waveforms for Read Operation(1) Notes: 1. Timing measurement reference level is 1.5V for -45 and -55 devices. Input AC drive levels are VIL = 0.0V and VIH = 3.0V. Timing measurement reference levels for all other speed grades are V OL = 0.8V and VOH = 2.0V. Input AC drive levels are VIL = 0.45V and VIH = 2.4V. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. Input Test Waveforms and Measurement Levels Output Test Load For -45 and -55 devices only: tR, tF < 5 ns (10% to 90%) Note: For -70, -90, -12, -15, and -20 devices: CL = 100 pF including jig capacitance, except for the -45 and -55 devices, where CL = 30 pF. tR, tF < 20 ns (10% to 90%) Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 8 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 5 Programming Waveforms(1) Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 3. When programming the AT27C010(L) at 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage transients. DC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL, VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 µA ICC2 VCC Supply Current (Program and Verify) IPP2 VPP Supply Current VID A9 Product Identification Voltage 6 AT27C010(L) Min Max Units ±10 µA -0.6 0.8 V 2.0 VCC + 1 V 0.4 V 2.4 CE = PGM = VIL 11.5 V 40 mA 20 mA 12.5 V AT27C010(L) AC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25 V, VPP = 13.0 ± 0.25V Limits Symbol Parameter tAS Address Setup Time 2 µs tCES CE Setup Time 2 µs tOES OE Setup Time 2 µs tDS Data Setup Time 2 µs tAH Address Hold Time 0 µs tDH Data Hold Time 2 µs tDFP OE High to Output Float Delay(2) tVPS VPP Setup Time tVCS VCC Setup Time tPW PGM Program Pulse Width(3) tOE Data Valid from OE tPRT VPP Pulse Rise TIme During Programming Notes: Test Conditions (1) Min Input Rise and Fall Times (10% to 90%) 20ns Input Pulse Levels 0.45V to 2.4V Max 0 Input Timing Reference Level 0.8V to 2.0V Output Timing Reference Level 0.8V to 2.0V Units 130 ns 2 µs 2 µs 95 105 µs 150 ns 50 ns 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP.. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven— see timing diagram. 3. Program Pulse width tolerance is 100 µsec ± 5%. Atmel’s 27C010(L) Integrated Product Identification Code Pins A0 O7 O6 O5 O4 O3 O2 O1 O0 Hex Data Manufacturer 0 0 0 0 1 1 1 1 0 1E Device Type 1 0 0 0 0 0 1 0 1 05 Codes 7 Rapid Programming Algorithm A 100 µs PGM pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 µs PGM pulse without verification. Then a verification / reprogramming loop is executed for each address. In the event a byte fails to pass verification, up to 10 successive 100 µs pulses are applied with a verification 8 AT27C010(L) after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is considered failed. After the byte verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared with the original data to determine if the device passes or fails. AT27C010(L) AT27C010 Ordering Information ICC (mA) tACC (ns) Active Standby Ordering Code Package 45 35 0.1 AT27C010-45JC AT27C010-45PC AT27C010-45TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-45JI AT27C010-45PI AT27C010-45TI 32J 32P6 32T Industrial (-40°C to 85°C) 35 0.1 AT27C010-55JC AT27C010-55PC AT27C010-55TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-55JI AT27C010-55PI AT27C010-55TI 32J 32P6 32T Industrial (-40°C to 85°C) 35 0.1 AT27C010-70JC AT27C010-70PC AT27C010-70TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-70JI AT27C010-70PI AT27C010-70TI 32J 32P6 32T Industrial (-40°C to 85°C) 55 70 Operation Range (continued) Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 32P6 32-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 32T 32-Lead, Plastic Thin Small Outline Package (TSOP) 9 AT27C010 Ordering Information (Continued) ICC (mA) tACC (ns) Active Standby Ordering Code Package 90 35 0.1 AT27C010-90JC AT27C010-90PC AT27C010-90TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-90JI AT27C010-90PI AT27C010-90TI 32J 32P6 32T Industrial (-40°C to 85°C) 35 0.1 AT27C010-90JA AT27C010-90PA 32J 32P6 Automotive (-40°C to 125°C) 35 0.1 AT27C010-12JC AT27C010-12PC AT27C010-12TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-12JI AT27C010-12PI AT27C010-12TI 32J 32P6 32T Industrial (-40°C to 85°C) 35 0.1 AT27C010-12JA AT27C010-12PA 32J 32P6 Automotive (-40°C to 125°C) 35 0.1 AT27C010-15JC AT27C010-15PC AT27C010-15TC 32J 32P6 32T Commercial (0°C to 70°C) 35 0.1 AT27C010-15JI AT27C010-15PI AT27C010-15TI 32J 32P6 32T Industrial (-40°C to 85°C) 35 0.1 AT27C010-15JA AT27C010-15PA 32J 32P6 Automotive (-40°C to 125°C) 120 150 Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 32P6 32-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 32T 32-Lead, Plastic Thin Small Outline Package (TSOP) 10 AT27C010(L) Operation Range AT27C010(L) AT27C010L Ordering Information ICC (mA) tACC (ns) Active Standby Ordering Code Package 45 25 0.1 AT27C010L-45JC AT27C010L-45PC AT27C010L-45TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-45JI AT27C010L-45PI AT27C010L-45TI 32J 32P6 32T Industrial (-40°C to 85°C) 25 0.1 AT27C010L-55JC AT27C010L-55PC AT27C010L-55TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-55JI AT27C010L-55PI AT27C010L-55TI 32J 32P6 32T Industrial (-40°C to 85°C) 25 0.1 AT27C010L-70JC AT27C010L-70PC AT27C010L-70TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-70JI AT27C010L-70PI AT27C010L-70TI 32J 32P6 32T Industrial (-40°C to 85°C) 25 0.1 AT27C010L-90JC AT27C010L-90PC AT27C010L-90TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-90JI AT27C010L-90PI AT27C010L-90TI 32J 32P6 32T Industrial (-40°C to 85°C) 25 0.1 AT27C010L-12JC AT27C010L-12PC AT27C010L-12TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-12JI AT27C010L-12PI AT27C010L-12TI 32J 32P6 32T Industrial (-40°C to 85°C) 25 0.1 AT27C010L-15JC AT27C010L-15PC AT27C010L-15TC 32J 32P6 32T Commercial (0°C to 70°C) 25 0.1 AT27C010L-15JI AT27C010L-15PI AT27C010L-15TI 32J 32P6 32T Industrial (-40°C to 85°C) 55 70 90 120 150 Operation Range Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 32P6 32-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 32T 32-Lead, Plastic Thin Small Outline Package (TSOP) 11 Packaging Information 32J, 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-016 AE .045(1.14) X 45˚ PIN NO. 1 IDENTIFY 1.67(42.4) 1.64(41.7) .025(.635) X 30˚ - 45˚ .012(.305) .008(.203) .553(14.0) .547(13.9) .595(15.1) .585(14.9) .032(.813) .026(.660) 32P6, 32-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) PIN 1 .566(14.4) .530(13.5) .530(13.5) .490(12.4) .021(.533) .013(.330) .090(2.29) MAX 1.500(38.10) REF .050(1.27) TYP .300(7.62) REF .430(10.9) .390(9.90) AT CONTACT POINTS .030(.762) .015(.381) .095(2.41) .060(1.52) .140(3.56) .120(3.05) .022(.559) X 45˚ MAX (3X) .453(11.5) .447(11.4) .495(12.6) .485(12.3) JEDEC OUTLINE MO-142 BD INDEX MARK 18.5(.728) 18.3(.720) 7.50(.295) REF 20.2(.795) 19.8(.780) 0.25(.010) 0.15(.006) 8.20(.323) 7.80(.307) 1.20(.047) MAX 0.15(.006) 0.05(.002) 0 5 REF 0.20(.008) 0.10(.004) 0.70(.028) 0.50(.020) *Controlling dimension: millimeters 12 AT27C010(L) .005(.127) MIN SEATING PLANE .065(1.65) .015(.381) .022(.559) .014(.356) .161(4.09) .125(3.18) .110(2.79) .090(2.29) .012(.305) .008(.203) 32T, 32-Lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches)* 0.50(.020) BSC .220(5.59) MAX .065(1.65) .041(1.04) .630(16.0) .590(15.0) 0 REF 15 .690(17.5) .610(15.5) AT27C010(L) 13 14 AT27C010(L) AT27C010(L) 15 Atmel Headquarters Atmel Operations Corporate Headquarters Atmel Colorado Springs 2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600 Europe 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759 Atmel Rousset Atmel U.K., Ltd. Coliseum Business Centre Riverside Way Camberley, Surrey GU15 3YL England TEL (44) 1276-686677 FAX (44) 1276-686697 Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4 42 53 60 00 FAX (33) 4 42 53 60 01 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon, Hong Kong TEL (852) 27219778 FAX (852) 27221369 Japan Atmel Japan K.K. Tonetsu Shinkawa Bldg., 9F 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Fax-on-Demand North America: 1-(800) 292-8635 International: 1-(408) 441-0732 e-mail [email protected] Web Site http://www.atmel.com BBS 1-(408) 436-4309 © Atmel Corporation 1998. Atmel Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s website. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual proper ty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. Marks bearing ® and/or ™ are registered trademarks and trademarks of Atmel Corporation. Terms and product names in this document may be trademarks of others. Printed on recycled paper. 0321J–07/98/xM