AWT6301 Cellular Dual Mode AMPS/CDMA 3.4 V/28 dBm Linear Power Amplifier Module ADVANCED PRODUCT INFORMATION - Rev 0.1 FEATURES InGaP HBT Technology High Efficiency: 53 % AMPS, 39 % CDMA Low Quiescent Current: 50 mA Low Leakage Current in Shutdown Mode: <1 mA VREF = +2.85 V (+2.7 V Min Over Temp.) Optimized for a 50 W System Low Profile Surface Mount Package: 1.1mm CDMA 1XRTT, 1xEV-DO Compliant Pinout Enables Easy Phone Board Migration From 4mm x 4mm Package APPLICATIONS Single Mode CDMA Wireless Handsets Dual Mode AMPS/CDMA Wireless Handsets PRODUCT DESCRIPTION M9 Package 8 Pin 3mm x 3mm Surface Mount Module The AWT6301 meets the increasing demands for higher efficiency and linearity in AMPS/CDMA 1X handsets, while reducing pcb area by 44%. The package pinout was chosen to enable handset manufacturers to switch from a 4mm x 4mm PA module with very few layout changes to the phone board. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the- art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. The self contained 3mm x 3mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 W system. GND at slug (pad) VREF 8 GND 7 RFOUT 3 6 GND VCC1 4 5 VCC2 1 VMODE 2 RFIN Bias Control Figure 1: Block Diagram 10/2003 AWT6301 GND VREF 1 8 GND VMODE 2 7 RFOUT RFIN 3 6 GND VCC1 4 5 VCC2 GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VREF Reference Voltage 2 VMODE Mode Control 3 RFIN RF Input 4 V CC1 Supply Voltage 5 V CC2 Supply Voltage 6 GND Ground 7 RFOUT RF Output 8 GND Ground ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 AWT6301 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PAR AME T E R MIN M AX U N IT Supply Voltage (VCC ) Wi th RF Dri ve DC Only 0 0 +5 +8 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PAR AME T E R MIN T YP M AX U N IT C OMME N T S Operati ng Frequency (f) 824 - 849 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.7 0 +2.85 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.8 - +3.1 +0.5 V Low Bi as Mode Hi gh Bi as Mode RF Output Power (POUT) 30.5(1) 27.5(1) 31.0 28.0 - dBm Case Temperature (TC) -20 - +85 °C AMPS CDMA The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +85 °C and VCC = +3.2 V, POUT is derated by 0.5 dB. ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 3 AWT6301 Table 4: Electrical Specifications - AMPS Operation (TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, VMODE = 0 V, POUT = +31 dBm, 50 W system) PAR AME T E R MIN T YP M AX U N IT Gai n 25 23.5 27 27 30 31 dB - 0.3 1.0 dB Power-Added Effi ci ency 50 53 - % Qui escent Current (Icq) - 100 120 mA VMODE = 0 V, Hi gh Bi as Reference Current - 5.0 8 mA through VREF pi n Mode Control Current - 0.35 1.0 mA through VMODE pi n Leakage Current - <1 5 mA VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noi se i n Recei ve Band - -134 -132 dBm/Hz Harmoni cs 2fo 3fo, 4fo - -35 -50 -30 -30 dBc Input Impedance - - 2:1 VSWR Gai n Vari ati on Spuri ous Output Level (all spuri ous outputs) - Load mi smatch stress wi th no permanent degradati on or fai lure 4 8:1 - - -65 - dBc VSWR C OMME N T S Over Temperature Over Temperature 869 MHz to 894 MHz POUT < +31 dBm Load VSWR < 8:1 Appli es over all voltage and temperature operati ng ranges VCC = +5.0 V PIN = +5 dBm Appli es over full operati ng temperature ranges ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 AWT6301 Table 5: Electrical Specifications - CDMA Operation (TC = +25 °C, VCC = +3.4 V, VREF = +2.85 V, 50 W system) PAR AME T E R MIN T YP M AX U N IT C OMME N T S Gai n 26 24.5 24 23 28 28 26 26 30 31 28 29 dB POUT = +28 dBm, VMODE = 0 V Over Temperature POUT = +16 dBm, VMODE = +2.85 V Over Temperature - -50 -50 - -47 -44 -46 -44 dBc POUT = +28 dBm, VMODE = 0 V Over Temperature POUT = +16 dBm, VMODE = +2.85 V Over Temperature - -60 -68 -57 -57 dBc 37 8 39 8.5 - % Qui escent Current (Icq) - 50 60 mA VMODE = 0 V, Low Bi as Reference Current - 5 8 mA through VREF pi n Mode Control Current - 0.35 1.0 mA through VMODE pi n Leakage Current - <1 5 mA VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noi se i n Recei ve Band - -135 -133 dBm/Hz Harmoni cs 2fo 3fo, 4fo - -35 -50 -30 -30 dBc Input Impedance - - 2:1 VSWR Adjacent Channel Power at 6885 kHz offset (1) Pri mary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Adjacent Channel Power at 61.98 MHz offset (1) Pri mary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Power-Added Effi ci ency (1) Spuri ous Output Level (all spuri ous outputs) Load mi smatch stress wi th no permanent degradati on or fai lure - - -65 dBc 8:1 - - VSWR POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Over Temperature POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V 869 MHz to 894 MHz POUT < +28 dBm Load VSWR < 8:1 Appli es over all voltage and temperature operati ng ranges VCC = +5.0 V PIN = +5 dBm Appli es over full operati ng temperature ranges Notes: (1) PAE and ACP limit applies at 836.5 MHz. ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 5 AWT6301 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control P OU T LEVELS B IAS MOD E V R EF V MOD E (all) High +2.85 V 0V CDMA - low power <+16 dBm Low +2.85 V +2.85 V CDMA - high power >+16 dBm High +2.85 V 0V - Shutdown 0V 0V AP P L IC AT ION AMPS Shutdown 6 ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 AWT6301 PACKAGE OUTLINE Figure 3: M9 Package Outline - 8 Pin 3mm x 3mm Surface Mount Module Figure 4: Branding Specification ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 7 AWT6301 COMPONENT PACKAGING Figure 5: Tape & Reel Packaging Table 7: Tape & Reel Dimensions 8 PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3mm X 3mm 12mm 4mm 2500 13" ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 AWT6301 NOTES ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003 9 AWT6301 ORDERING INFORMATION OR D E R N U MB E R T E MP E R AT U R E R AN GE PAC K AGE D E S C R IP T ION C OMP ON E N T PAC K AGIN G AWT6301M9P8 -30 °C to +110 °C 8 Pi n 3mm x 3mm Surface Mount Module Tape and Reel, 2500 pi eces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a products formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 10 ADVANCED PRODUCT INFORMATION - Rev 0.1 10/2003