Model B0322J5050A00 Rev D Ultra Low Profile 0805 Balun 50Ω to 50Ω Balanced Description The B0322J5050A00 is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering the GSM frequency. The B0322J5050A00 is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The B0322J5050A00 has an unbalanced port impedance of 50Ω and a 50Ω balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0322J5050A00 is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • 300 – 2200 MHz 0.7mm Height Profile 50 Ohm to 2 x 25 Ohm Low Insertion Loss Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature 300 Typ. 50 50 16 1.3 1.1 17 15 12.2 Max Unit 2200 MHz Ω Ω dB dB dB Degrees dB Watts ºC 1.6 1.2 20 2 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View Bottom View (Far-side) .026±.004 [0.65±0.10] .027±.002 [0.70±0.05] 1 2 3 6X .008 [0.20] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation Unbalanced Port GND Balanced Port Balanced Port Do not connect NC 6 5 6X .012 [0.30] 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model B0322J5050A00 Rev. D Typical Broadband Performance: 0 MHz. to 8.5 GHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 CM RR -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 -36 2000 7000 7500 8000 8500 7000 7500 8000 8500 5000 5000 4500 4000 3500 3000 2500 2000 1500 Frequency [MHz] 0 1500 1000 8500 8000 7500 7000 6500 6000 5500 5000 4500 -20 4000 -15 -2 3500 -1.5 3000 -10 2500 -1 2000 -5 1500 -0.5 0 0 500 0 500 6500 5 1000 6000 0.5 1000 6500 10 0 5500 1 500 6000 15 deg 2 1.5 0 [dB] 4500 Phase Balance 20 Frequency [MHz] [dB] 4000 Frequency [MHz] Amplitude Balance Frequency [MHz] USA/Canada: Toll Free: Europe: 5500 Frequency [MHz] 3500 0 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 -3.6 1500 -36 1000 -3.3 0 -3 -33 3000 -2.7 -30 2500 -2.4 -27 2000 -2.1 -24 1500 -1.8 -21 500 -18 1000 [dB] 0 0 500 [dB] Return Loss - Input (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model B0322J5050A00 Rev D Typical Performance: 200 MHz. to 2300 MHz. Return Loss - Input Insertion Loss 0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -30 -3 -33 -3.3 1.5 15 1 10 0.5 5 Frequency [MHz] 2300 Frequency [MHz] CM RR 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2300 2000 1700 1400 1100 800 500 -36 200 [dB] -15 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 2300 2000 1700 1400 200 2300 -20 2000 -2 1700 -15 1400 -1.5 1100 -10 800 -1 1100 0 -5 800 0 -0.5 500 deg 2 20 500 2000 Phase Balance Amplitude Balance 200 1700 Frequency [MHz] Frequency [MHz] [dB] 1400 1100 200 2300 2000 1700 1400 1100 800 500 200 800 -3.6 -36 500 [dB] 0 Model B0322J5050A00 Rev. D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical o and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/ C. An example of the PCB footprint used in the testing of these parts is shown below.In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Plated thru hole to ground 6X .014 [0.35] 6X .013 [0.33] .026 [0.66] 6X .002 [0.05] 4X .010 [0.25] 3X Transmission Line Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model B0322J5050A00 Rev D Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] 2.0 [50.8] ØC ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392