Battrax® Single Port Negative SLIC Protector RoHS This programmable Battrax device is referenced to a negative voltage source. This dual-chip package includes internal diodes for transient protection from positive surge events. (G) 5 2 3 (-VREF) (R) SIDACtor Devices 1 (T) For a diagram of a Battrax application, see Figure 6.47 in Section 6, “Reference Designs” of this Telecom Design Guide. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts VF Volts IDRM µAmps IGT mAmps IT Amps IH mAmps 100 B1101U_L |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 2.2 B1161U_L |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 2.2 160 B1201U_L |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 2.2 200 * “L” in part number indicates RoHS compliance. For non-RoHS compliant device, delete “L” from part number. For individual “UA” and “UC” surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • IPP ratings assume a VREF = -48 V. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • VREF maximum value for the B1101, B1161, and/or B1201 is -200 V. Surge Ratings in Amps Series IPP 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 * 10x160 ** 10x560 * 10x560 ** 5x320 * 9x720 ** Amps Amps Amps 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz Amps Amps Amps Amps A 20 150 150 90 50 75 75 C 50 500 400 200 150 200 175 Amps di/dt Amps Amps Amps/µs 45 75 20 500 100 200 50 500 * Current waveform in µs ** Voltage waveform in µs Telecom Design Guide • © 2006 Littelfuse 3 - 77 www.littelfuse.com Battrax® Single Port Negative SLIC Protector Thermal Considerations Package Symbol Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C 60 °C/W 6 5 4 Parameter Value Thermal Resistance: Junction to Ambient RθJA Unit 1 2 3 Capacitance Values pF Part Number B1101UAL B1101UCL B1161UAL B1161UCL B1201UAL B1201UCL MIN 50 50 50 50 50 50 MAX 200 200 200 200 200 200 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. IPP – Peak Pulse Current – %IPP +I VF VS VDRM VT -V IDRM +V IH IGT IT 100 50 0 tr td t – Time (µs) 10 IH 8 6 25 ˚C 4 2 IH (TC = 25 ˚C) tr x td Pulse Waveform Ratio of Percent of VS Change – % Half Value 0 14 12 0 -4 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Normalized VS Change versus Junction Temperature 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C www.littelfuse.com tr = rise time to peak value td = decay time to half value Waveform = tr x td -I V-I Characteristics Peak Value Normalized DC Holding Current versus Case Temperature 3 - 78 © 2006 Littelfuse • Telecom Design Guide