ROHM BD6886GUL

System Lens Driver Series for Mobile Phone Cameras
Parallel Interface Type
Lens Drivers for Voice Coil Motor
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
No.12015EAT02
●Description
The BD6883GUL, and the BH6453GUL motor driver provide 1 Constant-Current Driver Half-bridge, and 1 Constant-Voltage
Driver Half-bridge channel. The BD6886GUL, and the BD6369GUL motor driver provide 1 Constant-Voltage Driver H-bridge
channel. These lens drivers are offered in an ultra-small functional lens system for use in an auto focus system using a
Voice Coil motor.
●Features
1) BD6883GUL Characteristics
1) Ultra-small chip size package; 1.1mm×1.6mm×0.55mm
2) Low ON-Resistance Power CMOS output; on high side PMOS typ.0.65Ω, on low side NMOS typ.0.40Ω
3) ESD resistance (Human Body Model); 8kV
4) Built-in ±5% high-precision Constant-Voltage Driver (phase compensation capacitor-free design)
5) Built-in UVLO (Under Voltage Locked Out: UVLO)
6) Built-in TSD (Thermal Shut Down) circuit
7) Standby current consumption: 0μA Typ.
2) BH6453GUL Characteristics
1) Ultra-small chip size package; 1.5mm×0.9mm×0.55mm
2) Low ON-Resistance Power CMOS output; on high side PMOS typ.1.2Ω, on low side NMOS typ.0.4Ω
3) ESD resistance (Human Body Model); 8kV
4) Built in resistor for output current detect (phase compensation capacitor-free design)
5) 1.8V can be put into each control input terminal
6) Built-in UVLO (Under Voltage Locked Out: UVLO)
7) Built-in TSD (Thermal Shut Down) circuit
8) Standby current consumption: 0μA Typ.
3) BD6886GUL, BD6369GUL Characteristics
1) Ultra-small chip size package; 2.1mm×2.1mm×0.55mm
2) Low ON-Resistance Power CMOS output; on high and low sides in total typ.0.80Ω
3) ESD resistance (Human Body Model); 8kV
4) Built-in ±5% high-precision Constant-Voltage Driver (phase compensation capacitor-free design)
5) Control Input mode selection function
6) Built-in UVLO (Under Voltage Locked Out: UVLO)
7) Built-in TSD (Thermal Shut Down) circuit
8) Standby current consumption: 0μA Typ.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
1/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●Absolute Maximum Ratings (Ta=+25°C)
Symb
Parameter
ol
BD6883GUL
Power supply voltage
VCC
-0.5 to +6.5
Motor power supply voltage
VM
Control input voltage
VIN
-0.5 to VCC+0.5
Input voltage for
VLIM -0.5 to VCC+0.5
Constant-Voltage setting
Input voltage for
CLIM
Constant-Current setting
Power dissipation
Pd
510※1
Operating
Topr
-25 to +85
temperature range
Junction temperature
Tjmax
+150
Storage temperature range
Tstg
-55 to +150
H-bridge output current
Iout
-200 to +200※4
Limit
Unit
BH6453GUL
-0.5 to +4.5
-0.5 to VCC+0.5
BD6886GUL
-0.5 to +6.5
-0.5 to +6.5
-0.5 to VCC+0.5
BD6369GUL
-0.5 to +6.5
-0.5 to +6.5
-0.5 to VCC+0.5
-
-0.5 to VM+0.5
-0.5 to VM+0.5
V
-0.5 to VCC+0.5
-
-
V
430※2
730※3
730※3
mW
-25 to +85
-25 to +85
-25 to +85
°C
+125
-55 to +125
-300 to +300※5
+150
-55 to +150
-200 to +200※4
+150
-55 to +150
-500 to +500※4
°C
°C
mA
V
V
V
※1
Reduced by 4.08mW/°C over 25°C, when mounted on a glass epoxy board (50mm  58mm  1.75mm; 8 layers).
Reduced by 4.30mW/°C over 25°C, when mounted on a glass epoxy board (50mm  58mm  1.75mm; 8 layers).
※3
Reduced by 5.84mW/°C over 25°C, when mounted on a glass epoxy board (50mm  58mm  1.75mm; 8 layers).
※4
Must not exceed Pd, ASO, or Tjmax of 150°C.
※5
Must not exceed Pd, ASO, or Tjmax of 125°C.
※2
●Operating Conditions
Parameter
Symbol
Power supply voltage
Motor power supply voltage
Control input voltage
Input voltage for
Constant-Voltage setting
Input voltage for
Constant-Current setting
H-bridge output current
※6
Limit
Unit
VCC
VM
VIN
BD6883GUL
+2.5 to +5.5
0 to VCC
BH6453GUL
+2.3 to +3.6
0 to VCC
BD6886GUL
+2.5 to +5.5
+2.5 to +5.5
0 to VCC
BD6369GUL
+2.5 to +5.5
+2.5 to +5.5
0 to VCC
V
V
V
VLIM
0 to VCC
-
0 to VM
0 to VM
V
CLIM
-
0 to VCC
-
-
V
Iout
-150 to +150※6
-200 to +200※6
-150 to +150※6
-400 +400※6
mA
Must not exceed Pd or ASO.
Power Dissipation：Pd[mW]
Power Dissipation：Pd[mW]
●Power Dissipation Reduction
510
265
0
25
85
150
430
172
0
Ambient Temperature：Ta[°C]
Fig.1 BD6883GUL Power Dissipation Reduction
125
730
Power Dissipation：Pd[mW]
Power Dissipation：Pd[mW]
85
Fig.2 BH6453GUL Power Dissipation Reduction
730
380
0
25
Ambient Temperature：Ta[°C]
25
85
150
0
Ambient Temperature：Ta[°C]
25
85
150
Ambient Temperature：Ta[°C]
Fig.3 BD6886GUL Power Dissipation Reduction
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
380
Fig.4 BD6369GUL Power Dissipation Reduction
2/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●Electrical Characteristics
1) BD6883GUL Electrical Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V)
Parameter
Limit
Symbol
Unit
Conditions
Min
Typ
Max
ICCST
-
0
10
μA
ICC
-
0.9
1.4
mA
High level input voltage
VINH
2.0
-
VCC
V
Low level input voltage
VINL
0
-
0.7
V
High level input current
IINH
15
30
60
μA
Low level input current
IINL
-1
0
-
μA
VINL=0V
IVLIM
-1.5
-0.5
-
μA
VLIM=0V
VUVLO
1.6
-
2.4
V
RONP
-
0.65
0.80
Ω
Io=-150mA
RONN
-
0.40
0.60
Ω
Io=+150mA
VOH
1.9×VLIM
2.0×VLIM
2.1×VLIM
V
VLIM=1V with 10Ω load
Turn-on time
ton
-
1.5
5
μs
Io=-150mA, 10Ω load
Turn-off time
toff
-
0.1
2
μs
Io=-150mA, 10Ω load
Rise time
tr
-
1.5
8
μs
Io=-150mA, 10Ω load
Fall time
tf
-
0.05
1
μs
Io=-150mA, 10Ω load
Overall
Circuit current
during standby operation
Circuit current
PS=0V
PS=3V, VLIM=3V
with no signal and load
Control input (VIN=IN, PS)
VINH=3V,
pull-down resistor typ.100kΩ
Input for Constant-Voltage setting
Input current
UVLO
UVLO voltage
Constant-Voltage Drive block
PMOS Output
ON-Resistance
NMOS Output
ON-Resistance
Output high-level voltage
Output AC characteristic
100%
VIN
50%
50%
ton
0%
toff
-10%
0%
-10%
-50%
Motor current
-90%
tr
-50%
-90%
-100%
tf
Fig.5 BD6883GUL I/O Switching Waveform
(The direction flowing into IC is plus)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
3/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
2) BH6453GUL Electrical Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V)
Parameter
Symbol
Limit
Unit
Conditions
Min
Typ
Max
ICCST
-
0
5
μA
PS=0V
ICC
-
0.9
1.3
mA
PS=3V, IN=3V, no load
High-level input voltage
VINH
1.5
-
VCC
V
Low-level input voltage
VINL
0
-
0.5
V
High-level input current
IINH
15
30
60
μA
IINL
-1
0
-
μA
VUVLO
1.6
-
2.2
V
RONP
-
1.2
1.5
Ω
Io=-200mA
RONN
-
0.35
0.50
Ω
Io=+200mA
Overall
Circuit current
during standby operation
Circuit current
Control input (VIN=IN, PS)
Low-level input current
VINH=3V,
pull down resistance typ.100kΩ
VINL=0V
UVLO
UVLO voltage
Constant-Current Drive block
PMOS Output
ON-Resistance
NMOS Output
ON-Resistance
Offset current
Iofs
0
1
5
mA
CLIM=0V
Output current
Iout
180
200
220
mA
CLIM=0.8V, RL=10Ω
Drive system of Constant-Current
ISINK[A]=
CLIM[V]
2×2.0(Typ.)[Ω]
ISINK: VCC-OUT current
CLIM: VCC-OUT current setting voltage
RRNF: VCC-OUT current detection resistance
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
4/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
3) BD6886GUL, BD6369GUL Electrical Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V, VM=5.0V)
Parameter
Limit
Symbol
Unit
Conditions
Min
Typ
Max
ICCST
-
0
10
μA
PS=0V
Circuit current 1
ICC
-
0.9
1.4
mA
PS=3V, with no signal
Circuit current 2
IM
-
0.4
0.65
mA
PS=3V, VLIM=5V, no load
V
Overall
Circuit current
during standby operation
Control input (VIN=INA, INB, SEL, PS)
High-level input voltage
VINH
2.0
-
VCC
Low-level input voltage
VINL
0
-
0.7
V
High-level input current
IINH
15
30
60
μA
VINH=3V
Low-level input current
IINL
-1
0
-
μA
VINL=0V
Pull-down resistor
RIN
50
100
200
kΩ
IVLIM
-1.5
-0.5
-
μA
VUVLO
1.6
-
2.4
V
Output ON-Resistance
RON
-
0.80
1.20
Ω
Output high-level voltage
VOH
1.9×VLIM
2.0×VLIM
2.1×VLIM
V
VLIM=1V with 10Ω load
Turn-on time
ton
-
1.5
5
μs
Io=±150mA with 10Ω load
Turn-off time
toff
-
0.1
2
μs
Io=±150mA with 10Ω load
Rise time
tr
-
2
8
μs
Io=±150mA with 10Ω load
Fall time
tf
-
0.05
1
μs
Io=±150mA with 10Ω load
Input for Constant-Voltage setting
Input current
VLIM=0V
UVLO
UVLO voltage
Constant-Voltage Drive block
Io= ± 150mA on high and low
sides
in total
Output AC characteristic
100%
VIN
50%
50%
0%
ton
ton
toff
toff
90%
90%
50%
10%
-10%
Motor current
10%
0%
-10%
-50%
-50%
-90%
tf
100%
50%
tr
-90%
-100%
tf
tr
Fig.6 BD6886GUL, BD6369GUL I/O Switching Waveform
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
5/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●Electrical Characteristic Diagrams
All series
3.5
Top 85℃
Middle 25℃
Lower -2
4.0
Op. range (2.3V～3.6 V)
(BH6453GUL)
2.0
3.0
2.5
2.5
2.0
1.5
1.0
0.0
Top 85℃
Middle 25℃
Lower -2
0.5
-2.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0.0
Top 85℃
Middle 25℃
Lower -2
5℃
VM=5V
Output voltage, VOUTL [V]
0.4
Op. range (0～150mA)
0.2
0.3
Op. range (0~150mA)
(BD6886GUL)
0.2
0
0.5
Op. range (0～200mA)
3.0
2.0
0.1
0.2
0.3
0.4
0.0
0.5
0
Fig.11 NMOS Output Voltage
(BD6886GUL / BD6369GUL)
-0.1
-0.1
-0.2
-0.2
Top -25℃
Middle 25℃
Lower 85℃
VM=VCC=3
-0.9
-0.3
-0.4
-0.5
Op. range
(0~400mA)
(BD6369GUL)
-0.6
Top 85℃
Middle 25℃
Lower -2
5℃
VM=5V
-0.7
-0.8
-0.9
-1.0
0.1
0.2
0.3
0.4
0.5
-0.3
-0.4
-0.5
Op. range (0～200mA)
-0.6
-0.7
Top -25℃
Middle 25℃
Lower 85℃
VM=VCC=3
-0.8
-0.9
-1.0
-1.0
0
0
0.1
0.2
Output current, Io [A]
0.3
0.4
0
0.5
0.1
0.2
7.0
6.0
6.0
0.5
BH6453GUL
BD6886GUL / BD6369GUL
7.0
0.4
Fig.15 PMOS Output Voltage
(BH6453GUL)
Fig.14 PMOS Output Voltage
(BD6886GUL / BD6369GUL)
BD6883GUL
0.3
Output current, Io [A]
Output current, Io [A]
Fig.13 PMOS Output Voltage
(BD6883GUL)
0.5
-0.2
Op. range
(0~150mA)
(BD6886GUL)
Output voltage, VOUTH [V]
Output voltage, VOUTH [V]
-0.1
-0.6
0.4
BH6453GUL
0.0
-0.5
0.3
Fig.12 NMOS Output Voltage
(BH6453GUL)
0.0
-0.8
0.2
BD6886GUL / BD6369GUL
BD6883GUL
-0.7
0.1
Output current, Io [A]
0.0
Op. range (0～150mA)
7.0
Top 85℃
Middle 25℃
Lower -2
5℃VM=VC
Output current, Io [A]
Fig.10 NMOS Output Voltage
(BD6883GUL)
6.0
1.0
Output current, Io [A]
-0.4
5.0
Fig.9 Circuit Current
(BH6453GUL)
4.0
0.0
0.0
-0.3
4.0
BH6453GUL
Op. range (0~400mA)
(BD6369GUL)
0.1
0.1
0.4
3.0
5.0
Output voltage, VOUTL [V]
Top 85℃
Middle 25℃
Lower -2
5℃VM=VC
0.3
2.0
Supply voltage, Vcc [V]
0.5
0.2
1.0
BD6886GUL / BD6369GUL
BD6883GUL
0.1
1.0
Fig.8 Circuit Current
(BD6883GUL/BD6886GUL/BD6369GUL)
0.5
0
1.5
Supply voltage, Vcc [V]
Fig.7 Standby Current
（All series）
0.3
2.0
0.0
0.0
Supply voltage, Vcc [V]
0.4
Top 85℃
Middle 2
5℃Lower -
0.5
0.0
0.0
Output voltage, VOUTL [V]
Op. range (2.3V～3.6V)
3.0
Circuit current, Icc [mA]
Op. range (2.5V～5.5V)
(BD6883GUL, BD6886GUL,
BD6369GUL)
6.0
3.5
Op. range (2.5V～5.5V)
Circuit current, Icc [mA]
Standby current, Icc [ μA]
8.0
Output voltage, VOUTH [V]
BH6453GUL
BD6883GUL / BD6886GUL / BD6369GUL
10.0
500
Op. range (0～VM)
400
4.0
3.0
2.0
Top -25℃
Middle 25℃
Lower 85℃
VM=VCC=3
1.0
5.0
4.0
3.0
Top -25℃
Middle 25℃
Lower 85℃
VM=5V
VCC=3V
2.0
1.0
0.0
OUT current, IOUT [mA]
OUT voltage, VOH [V]
OUT voltage, VOH [V]
Op. range (0～VCC)
5.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
VLIM voltage [V]
Fig.16 Output High-Level Voltage
(BD6883GUL)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
300
200
Top -25℃
Middle 25℃
Lower 85℃
VM=VCC=3
100
0
0.0
0.0
Op. range (0～VCC)
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
VLIM voltage [V]
Fig.17 Output High-Level Voltage
(BD6886GUL / BD6369GUL)
6/16
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
CLIM voltage, VCLIM [V]
Fig.18 Current Limit Output Voltage
(BH6453GUL)
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
● Block Diagram, Application Circuit Diagram, Pin Arrangement, Pin Function Table
1) BD6883GUL Block Diagram, Application Circuit Diagram, Pin Arrangement, Pin Function Table
Bypass filter Capacitor for power
supply input. See. P.14/16.
Power-Saving
H: Active
L: Standby
0.1～10uF
VCC
0.5ch Constant-Voltage output pins.
Output H voltage.
OUT[V]=2×VLIM[V]
1B
PS 1A
Power Save
TSD & UVLO
BandGap
VCC
Motor control input
ISOURCE
IN 2A
Pre Driver
Logic
1C
OUT
×2
2C
VLIM
GND
2B
Setting for Constant-Voltage input terminal
In addition to the DC input, PWM signal drive
is also possible using filter components.
See. P.11/16
Fig.19 BD6883GUL Block Diagram, Application Circuit Diagram
1
2
A
PS
IN
B
VCC
VLIM
C
OUT
GND
Fig.20 BD6883GUL Pin Arrangement (Top View)
BD6883GUL Pin Function Table
Pin
Function
No.
Name
1A
PS
Power-saving pin
2A
IN
Control input pin
1B
VCC
Power supply pin
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
No.
2B
1C
2C
7/16
Pin
Name
VLIM
OUT
GND
Function
Output high-level voltage setting pin
Half-bridge output pin
Ground pin
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
2) BH6453GUL Block Diagram, Application Circuit Diagram, Pin Arrangement, Pin Function Table
Bypass filter Capacitor for power
supply input. See. P.14/16.
Power-Saving
H: Active
L: Standby
0.1～10uF
VCC
0.5ch Constant-Current output pins.
IOUT[mA] = CLIM[V] / (2×2(Typ)[Ω])
PS B1
Power Save
TSD & UVLO
BandGap
VCC
Motor control input
ISINK
IN A1
CLIM
VCC
Pre Driver
Logic
OUT
A2
V/I converter
RNF=2.0Ω
GND
Setting for Constant-Current input terminal
In addition to the DC input, PWM signal drive
is also possible using filter components.
See. P.11/16
Fig.21 BH6453GUL Block Diagram, Application Circuit Diagram
1
2
3
A
IN
CLIM
GND
B
PS
VCC
OUT
Fig.22 BH6453GUL Pin Arrangement (Top View)
BH6453GUL Pin Function Table
Pin
Function
No.
Name
1A
IN
Control input pin
2A
CLIM
Output current setting pin
3A
GND
Ground pin
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
No.
1B
2B
3B
8/16
Pin
Name
PS
VCC
OUT
Function
Power-saving pin
Power supply pin
Half-bridge output pin
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
3) BD6886GUL, BD6369GUL Block Diagram, Application Circuit Diagram, Pin Arrangement, Pin Function Table
Bypass filter Capacitor for power
supply input. See. P.14/16.
Power-Saving
H: Active
L: Standby
Bypass filter Capacitor for power
supply input. See. P.14/16.
0.1～10uF
VCC
4C
PS 3A
Power Save
TSD & UVLO
BandGap
0.1～10uF
1B
Motor control input
VM
INA 4B
Control Input mode selection
INB 3B
SEL
VLIM
Logic
2A OUTA
H bridge
Pre Driver
2D
×2
1C
3C
OUTB
IOUT
PGND
2C
1ch Constant-Voltage output pins.
Output H voltage.
OUT[V]=2×VLIM[V]
3D
GND
Setting for Constant-Voltage input terminal
In addition to the DC input, PWM signal drive
is also possible using filter components.
See. P.11/16
Fig.23 BD6886GUL, BD6369GUL Block Diagram, Application Circuit Diagram
1
2
3
4
A
N.C.
OUTA
PS
N.C.
B
VM
INDEX
POST
INB
INA
C
PGND
VLIM
SEL
VCC
D
N.C.
OUTB
GND
N.C.
Fig.24 BD6886GUL, BD6369GUL Pin Arrangement (Top View)
BD6886GUL, BD6369GUL Pin Function Table
Pin
Function
No.
Name
1A
N.C.
N.C.
2A
OUTA
H-bridge output pin A
3A
PS
Power-saving pin
4A
N.C.
N.C.
1B
VM
Motor power supply pin
2B
3B
INB
Control input pin B
4B
INA
Control input pin A
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
No.
1C
2C
3C
4C
1D
2D
3D
4D
9/16
Pin
Name
PGND
VLIM
SEL
VCC
N.C.
OUTB
GND
N.C.
Function
Motor ground pin
Output high-level voltage setting pin
Control input mode selection pin
Power supply pin
N.C.
H-bridge output pin B
Ground pin
N.C.
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●Function Explanation
1) Power-saving function (all series)
When the L voltage is applied the PS pin, the IC’s inside circuit stop, and when 0V applied, the circuit current became
0μA(Typ.), especially.
When the IC drive, serial input while the PS pin applied H voltage. (See the electrical characteristics; P.3, 4, 5/16)
2) Control Input Pin
（Ⅰ）IN pin (BD6883GUL, BH6453GUL)
The IN pin is used to program and control the motor drive modes.
(See the electrical characteristics; P3, 4/16, and the I/O Truth Table; P12/16)
（Ⅱ）INA, INB, SEL pins (BD6886GUL, BD6369GUL)
The INA and INB are used to program and control the motor drive modes.
When the L voltage is applied to the SEL pin, the I/O logic can be set to EN (Enable)/IN mode, and when the H voltage is applied
to the one, the I/O logic can be set to IN/IN mode. (See the electrical characteristics; P5/16, and the I/O Truth Table; P12/16)
3) H-bridge and Half-bridge on the output stage (ALL series)
Specify maximum current applied to the H-bridge and Half-bridge within the operating range, in consideration of power dissipation.
(See the Operating Conditions; P.2/16)
4) Drive system of Linear Constant-Voltage H-bridge (BD6883GUL, BD6886GUL, and BD6369GUL)
To set up the output H voltage, when the voltage input to the VLIM pin, the output H voltage is two times as high as the voltage.
（Ⅰ）BD6883GUL
The output H voltage VOH [V] = 2.0×VLIM [V]
（Ⅱ）BD6886GUL, BD6369GUL
The output H voltage VOH [V] = 2.0×VLIM [V]
(When VLIM [V] ＞ VCC [V] , Output H voltage is about VCC voltage)
･････①
2
(When VLIM [V] ＞
VM [V] , Output H voltage is about VM voltage)
2
･････②
For example, the output voltage is 2.0V±5%, if 1.0V is applied to the VLIM pin.
If the VLIM pin is shorted to the VM pin (or the same voltage level as the VM is applied), you can be used as a Full-ON Drive
H-bridge.
5) Drive system of Linear Constant-Current H-bridge (BH6453GUL)
To detect the output current and the output current settings
The BH6453GUL built in resistor for output current detect. The output current is kept constant by comparing it with the CLIM
voltage. In addition, impress a highly accurate voltage form the outside of IC to the CLIM terminal, when you do the output current
setting accuracy or more good.
Output current ISINK [A] =
CLIM [V]
･････③
2×2(Typ) [Ω]
If the CLIM pin applied 0.8V, Output current is 200mA±10%.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
10/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
7) Setting of PWM signal input VLIM and CLIM terminals (all series)
It is also possible to compose filters outside the IC, change an input voltage for output voltage and output current setting terminals
such as VLIM and CLIM terminals by the DUTY control using an PWM signal, etc., and use them as set values for control.
In this case, however, ensure the smoothing of the signals, heeding the constant number of the low-pass filter as stated below.
A cutoff frequency FC (-3dB attenuation frequency) of the low-pass filter in Fig25 is calculated by the formula mentioned below.
1
Cutoff frequency FC [Hz] =
[Hz]
･････④
2πCIN (RINA//RINB)
Set the cutoff frequency FC at 1/100 or below of the PWM frequency FPWM.
For example, if the cutoff frequency FC is set at 1/100 of FPWM when the PWM frequency FPWM=50[kHz], according to the formula
above:
1
Cutoff frequency FC [Hz] =
=
2πCIN (RINA//RINB)
1
×FPWM=
100
50×10
100
3
[Hz]
･････⑤
When CIN=0.1[μF], according to the formula above:
RINA//RINB=3.2[kΩ]
･････⑥
ON time
Where, an effective value of PWM signal as a DC current, according to crest values VMAX and ON DUTY [%]= ON time+ OFF time
is as follows:
VPWM[V]= VMAX[V]× ON DUTY[%]
･････⑦
An actual voltage VLIM input to terminals that specify output current and voltages, such as VLIM and CLIM terminals
is as follows according to resistance potential division of RINA and RINB:
VLIM[V]=
RINB
RINA+RINB
×VPWM[V]
･････⑧
For example, when an PWM signal with crest values VMAX=3[V] and DUTY [%]=5[%] is input, a VLIM value according to the formula
above is:
VLIM[V]=
RINB
× 3[V]× 50[%]
･････⑨
RINA+RINB
（Ⅰ）BD6883GUL, BD6886GUL, and BD6369GUL
Where, to specify an output voltage VOH=2[V], a value VLIM=1.0[V] according to the formula in the previous page. And then,
according to the formula above, VLIM=1.0[V].
VLIM=1.0[V]=VLIM=
RINB
×3[V]×50[%]
RINA+RINB
Therefore, RINA=0.5RINB
⑩
According to ⑥ and ⑩, RINA=4.8kΩ, RINB=9.6kΩ.
･････
（Ⅱ）BH6453GUL
Where, to specify an output current ISINK=100[mA], the following formula is derived according to the formula in the previous page
③, CLIM=0.4[V], and according to the formula above ⑨:
CLIM=0.4[V]=VLIM=
RINA=2.75RINB
According to ⑥ and ⑪:
RINB
×3[V]×50[%]
RINA+RINB
･････⑪
RINA=11.9kΩ, RINB=4.3kΩ
FPWM
VMAX
VPWM
RINA
VLIM
Output voltage / Constant current voltage terminals
VLIM / CLIM
RINB
CIN
Fig.25 Example PWM signal input
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
11/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●I/O Truth Table
BD6883GUL I/O Truth Table
INPUT
MODE
PS
IN
L
H
H
L
X
OUTPUT
OUT
L
H
Z※ 7
OUTPUT MODE
Sink
Source
Standby
L: Low, H: High, X: Don’t care, Z: Hi impedance
Sink is a direction of current flowing into the driver, and Source is a direction of current flowing out the driver.
When it is sink, which drive FULL ON.
※7
Z at the Constant-Voltage driver output L voltage for connect feedback resistance (20kΩ Typ.) for output H voltage setting between OUT pin and GND.
But output Power MOS is OFF condition.
BH6453GUL I/O Truth Table
INPUT
MODE
PS
IN
H
H
L
L
X
OUTPUT
OUT
L
H
Z
OUTPUT MODE
Sink
Source
Standby
L: Low, H: High, X: Don’t care, Z: Hi impedance
Sink is a direction of current flowing into the driver, and Source is a direction of current flowing out the driver.
When it is source, which drive FULL ON.
BD6886GUL, BD6369GUL I/O Truth Table
INPUT
MODE
PS
SEL
INA
L
EN/IN
L
H
H
L
H
L
IN/IN
H
H
H
L
X
X
INB
X
L
H
L
H
L
H
X
OUTPUT
OUTA
OUTB
Z※ 7
Z※ 7
H
L
L
H
L
L
L
H
H
L
Z※ 8
Z※ 8
Z※ 8
Z※ 8
OUTPUT MODE
Standby
Forward rotation
Reverse
rotation
Brake
Reverse rotation
Forward rotation
Standby
Standby
L: Low, H: High, X: Don’t care, Z: Hi impedance
At forward rotation, current flows from OUTA to OUTB. At reverse rotation, current flows from OUTB to OUTA.
※8
Z at the Constant-Voltage driver output L voltage for connect feedback resistance (20kΩ Typ.) for output H voltage setting between OUT pin and GND.
But output Power MOS is OFF condition.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
12/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●I/O Circuit Diagram
PS, IN
OUT, GND
VLIM
VCC
VCC
VCC
10k
PS
IN
1k
VLIM
OUT
100k
10k
GND
Fig.26 BD6883GUL I/O Circuit Diagram (Resistance values are typical ones.）
PS
IN
OUT, GND
VCC
140k
25k
PS
VCC
VCC
140k
10k
IN
OUT
100k
75k
60k
GND
CLIM
VCC
1k
CLIM
Fig.27 BH6453GUL I/O Circuit Diagram (Resistance values are typical ones.）
PS, INA, INB, SEL
VM, OUTA, OUTB, PGND
VCC
PS
INA
INB
SEL
VLIM
10k
100k
VCC
VM
VLIM
OUTA
1k
OUTB
10k
PGND
Fig.28 BD6886GUL, BD6369GUL I/O Circuit Diagram (Resistance values are typical ones.)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
13/16
2012.03 - Rev.A
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
Technical Note
●Operation Notes
1)
Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings, such as the applied voltage (VCC, VM) or operating temperature
range (Topr), may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or
open mode) when such damage is suffered. A physical safety measure, such as a fuse, should be implemented when
using the IC at times where the absolute maximum ratings may be exceeded.
2)
Storage temperature range (Tstg)
As long as the IC is kept within this range, there should be no problems in the IC’s performance. Conversely, extreme
temperature changes may result in poor IC performance, even if the changes are within the above range.
3)
Power supply and wiring
Be sure to connect the power terminals outside the IC. Do not leave them open. Because a return current is
generated by a counter electromotive force of the motor, take necessary measures such as putting a Capacitor
between the power source and the ground as a passageway for the regenerative current. Be sure to connect a
Capacitor of proper capacitance (0.1μF to 10μF) between the power source and the ground at the foot of the IC, and
ensure that there is no problem in properties of electrolytic Capacitors such as decrease in capacitance at low
temperatures. When the connected power source does not have enough current absorbing capability, there is a
possibility that the voltage of the power source line increases by the regenerative current an exceeds the absolute
maximum rating of this product and the peripheral circuits.
Therefore, be sure to take physical safety measures such as putting a zener diode for a voltage clamp between the
power source an the ground.
4)
Ground terminal and wiring
The potential at GND terminals should be made the lowest under any operating conditions. Ensure that there are no
terminals where the potentials are below the potential at GND terminals, including the transient phenomena. The
motor ground terminals PGND, and the small signal ground terminal GND are not interconnected with one another
inside the IC. It is recommended that you should isolate the large-current RNF pattern and PGND pattern from the
small-signal GND pattern, and should establish a one-point grounding at a reference point of the set, to avoid
fluctuation of small-signal GND voltages caused by voltage changes due to pattern wire resistances and large
currents. Also prevent the voltage variation of the ground wiring patterns of external components. Use short and thick
power source and ground wirings to ensure low impedance.
5)
Thermal design
Use a proper thermal design that allows for a sufficient margin of the power dissipation (Pd) at actual operating
conditions.
6)
Pin short and wrong direction assembly of the device.
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if positive and ground power supply terminals are reversed. The IC may also be damaged if pins
are shorted together or are shorted to other circuit’s power lines.
7)
Avoiding strong magnetic field
Malfunction may occur if the IC is used around a strong magnetic field.
8)
ASO
Ensure that the output transistors of the motor driver are not driven under excess conditions of the absolute maximum
ratings and ASO.
9)
TSD (Thermal Shut Down) circuit
If the junction temperature (Tjmax) reaches 175°C (but the BH6453GUL is 150°C), the TSD circuit will operate, and
the coil output circuit of the motor will open. There is a temperature hysterics of approximately 25°C (but the
BH6453GUL is 20°C). The TSD circuit is designed only to shut off the IC in order to prevent runaway thermal
operation. It is not designed to protect the IC or guarantee its operation. The performance of the IC’s characteristics is
not guaranteed and it is recommended that the device is replaced after the TSD is activated.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
14/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
10)
11)
Testing an application board
When testing the IC on an application board, connecting a Capacitor to a pin with low impedance subjects the IC to
stress. Always discharge Capacitors after each process or step. Always turn the IC's power supply off before
connecting it to, or removing it from a jig or fixture, during the inspection process. Ground the IC during assembly
steps as an antistatic measure. Use similar precaution when transporting and storing the IC.
Regarding the input pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements to keep them isolated. P-N
junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic
diode or transistor. For example, the relation between each potential is as follows:
When GND > Pin A, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic diode and transistor.
Parasitic elements can occur inevitably in the structure of the IC. The operation of parasitic elements can result in
mutual interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic
elements operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should
not be used.
Resistor
Transistor (NPN)
Pin B
Pin A
C
B
Pin B
E
Pin A
N
P
+
N
P
P
N
+
N
P substrate
Parasitic element
GND
P+
B
N
P
Parasitic
element
P
N
P substrate
Parasitic elements
GND
C
+
GND
E
Parasitic
GND elements
Other adjacent elements
Fig.29 Example of Simple IC Architecture
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
15/16
2012.03 - Rev.A
Technical Note
BD6883GUL,BH6453GUL,BD6886GUL,BD6369GUL
●Selecting a Model Name when Ordering
B
X
6
X
X
X
G
U
L
E2
Rohm model name
Package
Packaging and forming specification
E2: Embossed tape and reel
6883 : Constant voltage 0.5ch
6453 : Constant current 0.5ch
6886 : Constant voltage 1ch
6369 : Constant voltage 1ch
GUL : VCSP50L1 (BD6883)
GUL : VCSP50L1 (BH6453)
GUL : VCSP50L2 (BD6886)
GUL : VCSP50L2 (BD6369)
VCSP50L1 (BD6883GUL)
< Dimension >
< Tape and Reel information >
Tape
Embossed carrier tape (with dry pack)
Quantity
3000pcs
Direction
of feed
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand.)
1234
1234
1234
1234
1234
1234
Direction of feed
1Pin
Reel
(Unit:mm)
※When you order , please order in times the amount of package quantity.
VCSP50L1 (BH6453GUL)
< Tape and Reel information >
< Dimension >
Tape
Embossed carrier tape (with dry pack)
Quantity
3000pcs
E2
Direction
of feed
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand.)
1234
1234
1234
1234
1234
1234
Direction of feed
1Pin
Reel
(Unit:mm)
※When you order , please order in times the amount of package quantity.
VCSP50L2 (BD6886GUL, BD6369GUL)
< Tape and Reel information >
< Dimension >
Tape
Embossed carrier tape (with dry pack)
Quantity
3000pcs
E2
Direction
of feed
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand.)
1234
1234
1234
1234
1234
1234
Direction of feed
(Unit:mm)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Reel
1Pin
※When you order , please order in times the amount of package quantity.
16/16
2012.03 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
R1120A