Teccor® brand Thyristors 40 Amp Standard SCRs Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits • RoHS compliant • Glass – passivated junctions Main Features • Surge capability up to 520 A Applications Symbol Value Unit 40 A 400 to 1000 V 40 mA IT(RMS) VDRM /VRRM • Voltage capability up to 1000 V IGT Typical applications are AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Schematic Symbol Additional Information A Datasheet Resources K Samples G Absolute Maximum Ratings Parameter Test Conditions Value Unit IT(RMS) Symbol RMS on-state current TC = 100°C 40 A IT(AV) Average on-state current A ITSM I 2t di/dt IGM PG(AV) Tstg TJ TC = 100°C 25.0 single half cycle; f = 50Hz; TJ (initial) = 25°C 430 single half cycle; f = 60Hz; TJ (initial) = 25°C 520 I2t Value for fusing tp = 8.3 ms 1122 A2s Critical rate of rise of on-state current f = 60Hz ; TJ = 125°C 175 A/μs Peak gate current TJ = 125°C 3.5 A Average gate power dissipation TJ = 125°C Peak non-repetitive surge current A 0.8 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 125 °C © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 40 Amp Standard SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol IGT Test Conditions Value VD = 12V; RL = 30 Ω VGT VD = VDRM; gate open; TJ = 100°C MAX. 40 MIN. 5 MAX. 1.5 400V 650 600V 600 800V 1000V dv/dt VD = VDRM; gate open; TJ = 125°C Unit mA V 500 MIN. 250 400V 550 600V 500 800V V/μs 475 VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V IH IT = 400mA (initial) MAX. 60 mA tq (1) MAX. 35 μs tgt IG = 2 x IGT; PW = 15µs; IT = 80A TYP. 2.5 μs Note : (1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Static Characteristics Symbol Test Conditions VTM IT = 80A; tp = 380μs TJ = 25°C IDRM / IRRM VDRM / VRRM TJ = 125°C Unit 1.8 V MAX. 400 – 600V 10 800 V 20 1000 V 30 400 – 600V TJ = 100°C Value 800V 1000 MAX. 1500 1000V 5000 400 – 600V 2000 800V 3000 μA Thermal Resistances Symbol Parameter Rθ(J-C) Junction to case (AC) Sxx40R / Sxx40N Rθ(J-A) Junction to ambient Sxx40R Value Unit 0.6 °C/W 40 °C/W Note: xx = voltage © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 40 Amp Standard SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25°C) Ratio of IGT / IGT (TJ = 25°C) 2.0 1.5 1.0 0.5 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 85 110 -40 125 -15 10 35 60 85 110 125 Junction Temperature (TJ ) --(°C) Junction Temperature (TJ)-- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: O n-State Current vs. On-State Voltage (Typical) 120 2.0 TJ = 25°C 1.5 Instantaneous On-state Current (iT) – Amps Ratio of IH / IH (TJ = 25°C) 100 1.0 0.5 80 60 40 20 0.0 -40 -15 10 35 60 85 110 0 125 0.7 0.8 Junction Temperature (T J) -- (°C) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Figure 6: M aximum Allowable Case Temperature vs. RMS On-State Current 40 130 125 35 120 Maximum Allowable Case Temperature (TC )- °C Average On-State Power Dissipation [PD(AV)] - (Watts) 0.9 Instantaneous On-state Voltage (vT) – Volts 30 25 20 15 10 115 110 105 100 95 90 85 80 5 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 75 0 0 5 10 15 20 25 30 RMS On-State Current [IT(RMS)] - (Amps) © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 35 40 70 0 5 10 15 20 25 30 35 RMS On-State Current [IT(RMS)] - Amps 40 45 50 Teccor® brand Thyristors 40 Amp Standard SCRs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 130 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Maximum Allowable Ambient Temperature (TA) - °C Maximum Allowable Case Temperature (TC) - °C 125 120 115 110 105 100 95 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 85 100 80 60 40 20 0 80 0 5 10 15 20 25 0.0 0.5 1.0 1.5 2.0 2.5 RMS On-State Current [IT(RMS)] - Amps Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current Maximum Allowable Ambient Temperature (Tc) - °C 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 80 60 40 20 0 0.0 0.5 1.0 1.5 Average On-State Current [IT(AVE)] - Amps Figure 10: Peak Capacitor Discharge Current Figure 11: Peak Capacitor Discharge Current Derating 1.2 1.0 Normalized Peak Current Peak Discharge Current (ITM) - Amps 10000 1000 ITRM 0.8 0.6 0.4 0.2 tW 100 0.0 0.5 1.0 10.0 Pulse Current Duration (tw) - ms 50.0 0 25 50 75 100 125 150 Case Temperature (TC) - °C © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 40 Amp Standard SCRs Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G ate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 +0/-5 °C tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time Teccor® brand Thyristors 40 Amp Standard SCRs Physical Specifications Environmental Specifications Test Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Lead Material Copper Alloy Specifications and Conditions AC Blocking Temperature Cycling Temperature/ Humidity Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Thermal Shock Autoclave Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 O A E Dimension 8.13 .320 P ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K J N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 40 Amp Standard SCRs Dimensions – TO- 263 (N-package) — D2-Pak Surface Mount TC MEASURING POINT B Dimension E ANODE 8.41 .331 7.01 .276 A S W K GATE CATHODE G Max A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 0.025 0.035 0.63 0.89 E 0.048 0.055 1.22 1.40 F 0.060 0.075 1.52 1.91 7.01 .276 16.89 .665 8.89 .350 Min D 2.16 .085 7.01 .276 Max J F 11.68 .460 Millimeters Min U 8.13 .320 H D Inches AREA: 0.11 in 2 C V 1.40 .055 3.81 .150 G 0.095 0.105 2.41 2.67 H 0.083 0.093 2.11 2.36 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.87 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 2.03 .080 6.60 .260 Part Numbering System S 60 40 R DEVICE TYPE S: SCR VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 1000V CURRENT RATING 40: 40A Part Marking System 56 TO-220 AB - (R Package) TO-263 AB - (N Package) Lead Form Dimensions xx: Lead Form Option SENSITIVITY & TYPE [blank]: 40mA S6040R YM ® PACKAGE TYPE R: TO-220 (Non-isolated) N: TO-263 (D 2 - Pak) Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 55 Amp Standard SCRs Product Selector Part Number Voltage Gate Sensitivity Type Package X 40mA Standard SCR TO-220R X 40mA Standard SCR TO-263 400V 600V 800V 1000V Sxx40R X X X Sxx40N X X X Note: xx = Voltage Packing Options Marking Weight Packing Mode Base Quantity Sxx40R Part Number Sxx40R 2.2g Bulk 500 Sxx40RTP Sxx40R 2.2g Tube 500 (50 per tube) Sxx40NTP Sxx40N 1.6g Tube 500 (50 per tube) Sxx40NRP Sxx40N 1.6g Embossed Carrier 500 Note: xx = Voltage Reel Pack (RP) for TO-263 Embossed Carrier Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DIA (1.5) 0.945 (24.0) 0.827 (21.0) Cathode * * Cover tape Anode 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14