Bluetooth V2.0 Embedded PAN1455-EMB-2.0 Cut the

P

Cut the Cable
TM
Bluetooth V2.0 Embedded
PAN1455-EMB-2.0
OUTLINES - ENW89815C3KF
M
ODULES
Panasonic
Electronic Devices Europe GmbH
IRELESS
W
Now you can integrate Bluetooth very easy in your final
product, without qualification – with the PAN1455.
This solution follows the national and international
regulations, e.g. CE (Radio, EMC, Safety), FCC and IC.
The PAN1455 is manufactured in a 13.50 x 18.75 x 2.85 mm³
SMD package without an integrated ceramic antenna (refer to
PAN1555) and will be qualified as a Bluetooth 2.0 product.
Re-qualification of your product is usually not required.
This is why the PAN1455 is particularly suited for units
produced in smaller or medium quantities.
This module is a one to one replacement for the well known
PAN1450.
Any customizations for the software can be handled with
our recommended partners.
FEATURES
General
- Complete Bluetooth 2.0 + EDR solution
- Full product qualification (Bluetooth, CE, FCC, IC)
- Profiles: GAP, SDAP, SPP, HID and HDP available, other could
be supported on request.
- CSR BlueCore6-ROM inside
- Cortex-M3 ST32F103 core for embedded profiles or
application software
- Temperature Range from -40°C to +85°C
- Supply Voltage Range from 2.7V to 3.6V, typ. 3.3V
- Fast Connection Setup
- Support for 802.11 Coexistence
Interfaces
- UART (programmable baud rate), USB, I²C, SPI and ADC
- 18 GPIOs for individual usage for your embedded software
- All bluetooth data rate up to 2178kbps asymmetric
- PCM Interface Master / Slave supporting 13 or 16 bit linear,
8 bit µ-law or A-law Codecs and CVSD transcoders on up to
3 SCO channels.
Bluetooth
- High Sensitivity Design (typ. -86 dBm)
- Full 8- to 128-bit encryption
- Power control and RSSI, Hold-, Park- and Sniffmode
- Support for very low power modes - sleep and deep sleep
Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt
regarding the safety of this product, kindly inform us immediately for technical consultation.
PAN1455 Rev. B1
www.pedeu.panasonic.de
wireless@eu.panasonic.com
Hardware Status:
Pre Production
P
CONTACT
Carsten Pfaff
BlueTooth Product Manager
Radiometrix Ltd
Hartcran House
231 Kenton lane, Harrow, Middlesex
HA3 8RP, England.
Tel: +44 (0)20 8907 5077
Fax: +44 (0)20 8909 2233
email: carsten@radiometrix.co.uk
APPLICATIONS
All Embedded Wireless Applications
- Printer Adapters
- Printers
- Access Points
- Wireless Sensors
- Industrial Applications
-
Cable Replacement
Personal Digital Assistants (PDAs)
Personal Navigation Devices
Automotive Applications
Medical Applications
BLOCK-DIAGRAM








































TECHNICAL CHARACTERISTICS
Parameter
-3
Receiver Sensitivity (BER=10 )
Output Power
Value
Condition / Note
-86 dBm typ.
ideal wanted signal
+4 dBm typ.
Power Supply
2,7 - 3,6 V
Single operation voltage
Ultra Low Power Mode
<100 µA
T = 25°C
ACL (connected DH5)
50.5mA to 49.5mA
max. power to min. power
(1)
ACL (connected DH1)
48.0mA to 46.0mA
max. power to min. power
(1)
Operating Temperature Range
-40°C to +85°C
Storage until +125°C
(1) Figure indicates to the shortest poll period and to the slave mode
www.pedeu.panasonic.de
wireless@eu.panasonic.com
Hardware Status:
Pre Production