0 CHIP TYPE ALUMINUM ELECTROLYTIC CAPACITORS Cautions for Using Aluminum Electrolytic Capacitors Please read product specifications before using the products. The following cautions should be observed when using our aluminum electrolytic capacitors to assure their maximum stability and performance. When your application design conditions or operating conditions exceed the limit of the product specification, please contact us. If used under conditions beyond the limit of our specifications, it may cause defects such as short circuit, open circuit, leakage, explosion or combustion. Cautions for usage 1. DC electrolytic capacitors are polarized. If used with a wrong polarity, it creates an abnormal current resulting in a short circuit or damage to itself. Use DC bipolar electrolytic capacitors for use with uncertain or unknown polarity. DC capacitors cannot be used in AC circuits. change with a change in the temperature. Such changes are temporary and the original characteristics will be restored at the original temperature (if the characteristics are not deteriorated by remaining at a high temperature for a long time). If used at a temperature exceeding the guaranteed temperature range, the capacitor may be 2. Use within the rated voltage. damaged due to the increased leakage current. Pay If a voltage exceeding the rated voltage is applied, it attention to the capacitor temperature being affected may cause characteristic deterioration or damage by the ambient temperature of the unit, the due to the increased leakage current. temperature inside the appliance, the heat radiated When ripple current is loaded, make sure that the by another hot component in the unit and the heat peak value of the ripple voltage does not exceed the inside the capacitor itself due to the ripple current. 0000000000000000000000000000000000000000000000000000000 rated voltage. (1) The electrostatic capacitance is normally shown as the value at 20C-120Hz. It increases as the 3. Using for power supply circuit. temperature raises and decreases as it lowers. (2) The tangent of loss angle (tan) is normally While aluminum electrolytic capacitors are operated electrolyte liquid inside dries up and E.S.R. shown as the value at 20C-120Hz. it decreases (Equivalent Series Resistance) of the capacitor as the ambient temperature gets high and increases. In case operated longer than rated life increases as it gets low. time, the capacitance much decreases, tangent of (3) The leakage current increases as the temperature loss angle and E.S.R. much increases. Therefore for gets high and decreases as it gets low. some case the sum of bias direct voltage and the peak of ripple voltage is over the rated voltage of the 7. Changes in the characteristics due to frequency. capacitor. The characteristics of an electrolytic capacitor will For any type of circuit, in case the sum of bias direct change according to the change in the operating voltage and the peak of ripple voltage is over the frequency. rated voltage of the capacitors or in case the (1) The electrostatic capacity is normally shown as 00000000000000 minimum voltage is lower than 0 (zero) volt, the the value at 20C-120Hz. It decreases as the voltage control for the capacitors shall be provided. frequency increases. 0 (2) The tangent of loss angle (tan) is normally 0 4. Do not use in a circuit which requires rapid shown as the value at 20C-120Hz. It increases charging or discharging. as the frequency gets high. 0 If used in a circuit requiring rapid charging or (3) The impedance is normally shown as the value at discharging, it may cause characteristic deterioration 100kHz 20C. It increases as the frequency or damage to itself due to the heat generated inside lowers. the capacitor. In such cases, contact us for our rapid charging/discharging capacitors. 8. Aluminum electrolytic capacitor life. The life of an aluminum electrolytic capacitor 5. Use within the rated ripple current. terminates when it fails due to the deterioration in its If applied ripple current exceeds rated ripple current, electronic characteristics. Temperature and the ripple the life of the capacitor may be shortened, or in an current since they especially affect the life. See chart extreme case it gets destroyed due to its internal heat. on page. Use high-ripple type capacitors for such circuits. 9. Changes in aluminum electrolytic capacitors 6. Changes in characteristics due to operating during storage. 0 temperature. After storage for a long period, whether unused of The characteristics of an electrolytic capacitor will mounted on the appliance, the leakage current of an 0 7 NOTE Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. 0 CHIP TYPE ALUMINUM ELECTROLYTIC CAPACITORS aluminum electrolytic capacitor will increase. This tendency is more prominent when the ambient temperature is high. If a capacitor has been stored for more than 2 years under normal temperature (shorter if high temperature) and it shows increased leakage current, a treatment by voltage application is recommended. Addition of a protective circuit in the design of the appliance is also recommended, considering the effect of the initial increased current. given to the lead wire terminals due to the difference between the hole pitch and the lead pitch. 16. Capacitors with pressure valves. A part of the capacitor case is made thin to have the function as the pressure valve in order to prevent explosion due to the rise of inside pressure when a reverse or excessive voltage is applied to the capacitor. Once it has worked as a valve, the whole capacitor needs to be replaced since the valve will not restore. When you use a capacitor with pressure valve, provide certain space above the pressure valve as below to prevent an interference when it works as a valve. 10. Insulation between the capacitor case and the cathode terminal. The capacitor case and the cathode terminal are connected through the electrolyte which has uncertain resistance. If a complete insulation of the case is necessary, add an insulator at assembly. Diameter of the capacitor 18 to less (mm) 11. External sleeve. During a preheating or a hardening of mounting Required space 2.0 adhensive may cause a sleeve cracked. above the valve(mm) The capacitors are usually sleeved with poly vinylchroraide or poly ethylene terephtharate for the 17. Double-sided PCB’s indication purpose only. Please do not consider it as When you use electrolytic capacitors on a an insulation. 0000000000000000000000000000000000000000000000000000000 double-sided PCB, be careful not to have the circuit pattern run under where the capacitor is mounted. 12. Fumigation Process Otherwise it may cause a short circuit on the PCB When exporting electronic equipment abroad, depending on the condition of mounting. fumigation process may be performed on wooden packaging material with a halogen (compound) gas such as methyl bromide. Exercise care as this halogen gas may corrode capacitors. Also, use caution to epidemic preventive agent as corrosive component such as halogen may be contained. 18. Regarding to connection of capacitors Aluminum electrolytic capacitor has electrolyte liquid so that the most portion of electric loss characteristics came from E.S.R (Equivalent Series Resistance) of electrolyte liquid. Therefore the capacitor is an electronic devise which can flow high ripple current in case the temperature increases and it decreases E.S.R. In case connecting two capacitors or more, E.S.R. of the capacitors is close to the resistance of the circuit. Therefore in case current is unbalanced and some capacitors has high ripple current, temperature increase, it makes more high current and finally it is over the rated ripple current. For parallel connection of capacitors the proper design of electric circuit such as b alancing of each capacitors resistance or control of total ripple current shall be provided to avoid excess ripple current and voltage. When two or more capacitors are arranged in series, the voltage given to each capacitors shall be kept below the rated voltage level, by also giving consideration to the balance of the voltage impressed on the capacitors. Further, partial pressure resistor which considers leakage current shall be provided parallel to each condenser not to have over-voltage impressed on. 13. Specific Operating Environments Capacitors may corrode when stored or used in a place filled with acidic toxic gases (such as hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, bromine, methyl bromide, etc.) 00000000000000 If capacitors are used or stored in such environments, 0 please let us know. 0 0 0 14. Use at a high altitude The use of capacitors at high altitudes such as on an airplane causes a large difference between the internal pressure of the capacitors and the atmospheric pressure. However, there is no problem in use under atmospheric pressure up to about an altitude of 10,000 meters. Please check the operation of electronic equipment at the operating environmental temperature because the temperature lowers with increased altitude. 15. Hole pitch adjustment of the PCB to the capacitors. Set the hole pitch of the PCB to the lead pitch (the “F” distance in the catalog) of the capacitor. Be careful since a short circuit, a cut or an increase in the leakage current etc. may be caused by the stress NOTE Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. 0 8 0 CHIP TYPE ALUMINUM ELECTROLYTIC CAPACITORS 5. Cleaning after Soidering Recommended cleaning method (1) cleaning solutions: (a) CLEANTHROUGH 710M, 750H, 750L (b) PINEALPHA ST-100S (c) Techno Care FRW-4~17 (d) Isopropyl alcohol (2-propanol) (2) Cleaning conditions: (a) The temperature of cleaning solution shall be less than 60ºC. (b) Use immersion or ultrasonic waves within two minutes. (c) After cleaning, capacitors and PCB’s shall thoroughly be rinsed and dried with hot blast for more than 10 minutes. The temperature of such breeze should be less than the upper category temperature. (d) After cleaning, do not keep capacitors in cleaning solution atmosphere or airtight containers. During cleaning, control the cleaning solution against contamination. Cautions for Mounting 1. Cautions for mounting. Check the ratings (electrostatic capacitance and rated voltage) of the capacitor before mounting. Check the polarity of the capacitor to the chassis. Do not drop the capacitor to the floor. Do not use the dropped capacitor. Do not deform the capacitor for mounting. 2. Do not apply excessive pressure to the capacitor, its terminals or lead wires. Make sure that the contact path of the capacitor meets the hole pitch of the PCB before mounting. Transient recovery voltage may be generated in the capacitor due to dielectric absorption. If required, this voltage can be discharged with a resistor with a value of about 1 k. A PCB self-standing (snap-in) type capacitor should be pushed to the end (till there is no space) to the PCB for mounting. Do not set the automatic insertion machine to clinch the capacitor lead wires too strong. 6. Fixing adhesives and coating materials. 0000000000000000000000000000000000000000000000000000000 Pay attention to the impact given by the component Do not use fixing adhesive or coating material receptacles of the automatic insertion/mounting containing halogen-based solvent. machines and the product checker, and from the Before applying the fixing adhesive or the coating centering operation. material, make sure that there is no remaining flux or stains between the PCB and the sealed part of the 3. Soldering. capacitor. Do not dip the capacitor into melted solder. Before applying the fixing adhesive or the coating The soldering conditions material, make sure that the detergent etc. has dried Chip type: Please refer 5 page. up. small and large type: 260ºC, 10 s (max.) Do not cover the whole surface of the sealed part The preliminary heating and other conditions (terminal side) of the capacitor with the fixing described in the catalog or product specifications. adhesive or the coating material. Do not flux other part than the terminals. Observe the description in the catalog or the product If there is a direct contact between the sleeve of the specifications concerning the thermal stiffening capacitor and the printed circuit pattern or a metal conditions of the fixing adhesive or the coating part of another component such as a lead wire, it may 00000000000000 material. (If there is no such description, contact us.) shrinkage of crack. 0 cause When both discrete and SMT components are on the When you use the capacitor with its sleeve touching same PCB, the fixing material for the SMT directly to the PCB, excessive solder temperature or 0 components may cause crack, tear or shrinkage on excessive soldering time may cause the sleeve to 0 the external sleeve depending on the thermal shrink or crack during the heat. stiffening condition. If the application is for extended use, understand and manage the soldering characteristics to avoid abnormal current caused by a contact failure Other Cautions between the capacitor and the PCB. 1. Do not touch capacitor terminals with bare hands. 4. Handling after soldering. You may get electric shock or your hand may be burnt. After soldering, do not tilt, push down or twist the Discharge it with a 1 K resistance before use if capacitor. necessary. After soldering, do not hold the capacitor as a handle 0 to carry the PCB. After soldering, do not hit the capacitor with any obstacle. If PCB’s are piled up for storage, the capacitor should not touch another PCB or component. 2. Do not short the capacitor terminals with a conductor. Do not spill conductive solution including 0 acid or alkaline solution on the capacitor. 9 NOTE Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. 0 CHIP TYPE ALUMINUM ELECTROLYTIC CAPACITORS 3. Periodical inspections should be established for the capacitors used in industrial appliances. The following items should be checked: (1) Appearance: Check if there is any open valve or leakage. (2) Electronic performance: Check the leakage current, the electrostatic capacitance, the tangent of loss angle and other items described in the catalog or the product specifications. 4. Take the following measures in case of emergency. If you see gas coming out of the capacitor valve when the set is in operation, turn off the power switch of the unit or unplug the power cord from the outlet. Keep your face away from the capacitor pressure valve, since the high temperature gas at over 100ºC bursts out when the valve works. If the gas gets into your eyes or your mouth, wash your eyes or your mouth. Do not ingest the capacitor electrolyte. If the electrolyte gets on your skin, wash it out with soap. capacitor tends to increase when stored for a long time. This tendency becomes more prominent if the ambient temperature is high. The leakage current will be decreased by voltage application. If necessary, treatment by voltage application should be made on the capacitors which have been stored for a long period (more than 2 years after production). Do not store capacitors at a place where there is a possibility that they may get water, salt or oil spill. Do not store capacitors at a place where the air contains dense hazardous gas (hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.). Fumigation treatment with toxic gas covering the whole wooden container frames as moth proofing during shipment may leave residual toxic gas. Do not store capacitors at a place where it gets ultraviolet or radioactive rays. 6. Disposing of capacitors. Punch a hole or crush the capacitors (to prevent explosion) before incineration at approved facility. If they are not to be incinerated, bring them to a professional industrial waste disposal company. 5. Storing conditions. Avoid high temperature or high humidity when storing 0000000000000000000000000000000000000000000000000000000 7. Other notes. Please refer to the following literature for anything not described in the product specifications or the catalog. capacitors. Keep the storing temperature at 5ºC to 35ºC and the relative humidity not more than 75%. The leakage current of an aluminum electrolytic 00000000000000 0 0 0 0 0 NOTE Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. 10