HM-65642/883 ® 8K x 8 Asynchronous CMOS Static RAM May 2002 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. • Full CMOS Design • Six Transistor Memory Cell • Low Standby Supply Current . . . . . . . . . . . . . . . . 100µA • Low Operating Supply Current. . . . . . . . . . . . . . . 20mA • Fast Address Access Time . . . . . . . . . . . . . . . . . . 150ns • Low Data Retention Supply Voltage . . . . . . . . . . . 2.0V • CMOS/TTL Compatible Inputs/Outputs • JEDEC Approved Pinout • Equal Cycle and Access Times • No Clocks or Strobes Required • Gated Inputs - No Pull-Up or Pull-Down Resistors Required • Temperature Range -55oC to +125oC • Easy Microprocessor Interfacing • Dual Chip Enable Control The HM-65642/883 is a CMOS 8192 x 8-bit Static Random Access Memory. The pinout is the JEDEC 28 pin, 8-bit wide standard, which allows easy memory board layouts which accommodate a variety of industry standard ROM, PROM, EPROM, EEPROM and RAMs. The HM-65642/883 is ideally suited for use in microprocessor based systems. In particular, interfacing with the Intersil 80C86 and 80C88 microprocessors is simplified by the convenient output enable (G) input. The HM-65642/883 is a full CMOS RAM which utilizes an array of six transistor (6T) memory cells for the most stable and lowest possible standby supply current over the full military temperature range. Ordering Information PACKAGE TEMPERATURE RANGE 150ns/75µA 150ns/150µA CERDIP -55oC to +125oC HM1-65642B/883 HM1-65642/883 CLCC -55oC to +125oC HM4-65642B/883 HM4-65642/883 200ns/250µA HM1-65642C/883 - PKG. NO. F28.6 J32.A Pinouts 25 A8 E2 A6 4 W 26 E2 VCC A7 3 NC 27 W NC 28 VCC A12 2 A12 NC 1 HM4-65642/883 (CLCC) TOP VIEW A7 HM-65642/883 (CERDIP) TOP VIEW 4 3 2 1 32 31 30 PIN A6 5 29 A8 A5 6 28 A9 A4 7 27 A11 A DESCRIPTION Address Input DQ Data Input/Output E1 Chip Enable E2 Chip Enable W Write Enable G Output Enable A5 5 24 A9 A4 6 23 A11 A3 8 26 NC A3 7 22 G A2 9 25 G A2 8 21 A10 A1 10 A1 9 20 E1 A0 11 23 E1 A0 10 19 DQ7 NC 12 22 DQ7 NC DQ0 11 18 DQ6 DQ0 13 21 DQ6 GND Ground VCC Power 15 16 17 18 19 20 16 DQ4 DQ2 NC DQ3 DQ4 DQ5 DQ1 12 DQ2 13 GND 14 15 DQ3 GND 17 DQ5 14 DQ1 24 A10 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 220 No Connections FN3004.2 HM-65642/883 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Input or Output Voltage Applied for all Grades. . . . . . . GND -0.3V to VCC +0.3V Typical Derating Factor . . . . . . . . . . . 5mA/MHz Increase in ICCOP ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance (Typical) θJA θJC CERDIP Package . . . . . . . . . . . . . . . . 45oC/W 8oC/W 10oC/W CLCC Package . . . . . . . . . . . . . . . . . . 55oC/W Maximum Storage Temperature Range . . . . . . . . .-65oC to +150oC Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . +175oC Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . +300oC Die Characteristics Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101,000 Gates CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Input Low Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.8V Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . +2.2V to VCC +0.3V Data Retention Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 2.0V Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . 40ns Max. TABLE 1. HM-65642/883 DC ELECTRICAL PERFORMANCE SPECIFICATIONS Device Guaranteed and 100% Tested (NOTE 1) CONDITIONS PARAMETER SYMBOL High Level Output Voltage VOH 1 VCC = 4.5V, IO = -1.0mA Low Level Output Voltage VOL High Impedance Output Leakage Current IIOZ Input Leakage Current Standby Supply Current II ICCSB1 GROUP A SUBGROUPS LIMITS TEMPERATURE MIN MAX UNITS 1, 2, 3 -55oC ≤ TA ≤ +125oC 2.4 - V VCC = 4.5V, IO = 4.0mA 1, 2, 3 -55oC ≤ TA ≤ +125oC - 0.4 V HM-65642B/883, HM-65642/883 VCC = 5.5V, G = 2.2V, VI/O = GND or VCC 1, 2, 3 -55oC ≤ TA ≤ +125oC -1.0 +1.0 µA HM-65642C/883 VCC = 5.5V, G = 2.2V, VI/O = GND or VCC 1, 2, 3 -55oC ≤ TA ≤ +125oC -2.0 +2.0 µA HM-65642B/883, HM-65642/883 VCC = 5.5V, VI = GND or VCC 1, 2, 3 -55oC ≤ TA ≤ +125oC -1.0 +1.0 µA HM-65642C/883 VCC = 5.5V, VI = GND or VCC 1, 2, 3 -55oC ≤ TA ≤ +125oC -2.0 +2.0 µA HM-65642B/883 VCC = 5.5V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 100 µA HM-65642/883 VCC = 5.5V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 250 µA HM-65642C/883 VCC = 5.5V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 400 µA Standby Supply Current ICCSB VCC = 5.5V, IO = 0mA, E1 = 2.2V or E2 = 0.8V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 5 mA Enable Supply Current ICCEN VCC = 5.5V, IO = 0mA, E1 =0.8V, E2 = 2.2V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 5 mA Operating Supply Current ICCOP VCC = 5.5V, G = 5.5V, (Note 2), f = 1MHz, E1 = 0.8V, E2 = 2.2V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 20 mA 221 HM-65642/883 TABLE 1. HM-65642/883 DC ELECTRICAL PERFORMANCE SPECIFICATIONS (Continued) Device Guaranteed and 100% Tested PARAMETER Data Retention Supply Current Functional Test (NOTE 1) CONDITIONS SYMBOL ICCDR FT LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS - 75 µA HM-65642B/883 VCC = 2.0V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC HM-65642/883 VCC = 2.0V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 150 µA HM-65642C/883 VCC = 2.0V, E1 = VCC -0.3V or E2 = GND +0.3V 1, 2, 3 -55oC ≤ TA ≤ +125oC - 250 µA 7, 8A, 8B -55oC ≤ TA ≤ +125oC - - - VCC = 4.5V (Note 3) NOTES: 1. All voltages referenced to device GND. 2. Typical derating 5mA/MHz increase in ICCOP. 3. Tested as follows: f = 2MHz, VIH = 2.4V, VIL = 0.4V, IOH = -4.0mA, IOL = 4.0mA, VOH ≥ 1.5V, and VOL ≤ 1.5V. TABLE 2. HM-65642/883 AC ELECTRICAL PERFORMANCE SPECIFICATIONS LIMITS PARAMETERS SYMBOL (NOTES 1, 2) CONDITIONS HM65642B/883 HM65642/883 HM65642C/883 GROUP A SUBGROUPS TEMPERATURE MIN MAX MIN MAX MIN MAX UNITS Read/Write/ Cycle Time TAVAX VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 150 - 150 - 200 - ns Address Access Time TAVQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC - 150 - 150 - 200 - Output Enable Access Time TGLQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC - 70 - 70 - 70 ns Chip Enable Access Time TE1LQV TE2HQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC - 150 - 150 - 200 ns Write Recovery Time TWHAX TE1HAX TE2LAX VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 10 - 10 - 10 - ns Chip Enable to End-of-Write TE1LE1H TE2HE2L VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 90 - 90 - 120 - ns Address Setup Time TAVWL TAVE1L TAVE2H VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 0 - 0 - 0 - ns Write Enable Pulse Width TWLWH VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 90 - 90 - 120 - ns Data Setup Time TDVWH TDVE1H TDVE2L VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 60 - 60 - 80 - ns 222 HM-65642/883 TABLE 2. HM-65642/883 AC ELECTRICAL PERFORMANCE SPECIFICATIONS (Continued) LIMITS PARAMETERS Data Hold Time (NOTES 1, 2) CONDITIONS SYMBOL HM65642B/883 HM65642/883 HM65642C/883 GROUP A SUBGROUPS TEMPERATURE MIN MAX MIN MAX MIN MAX UNITS TWHDX VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 5 - 5 - 5 - ns TE1HDX VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 10 - 10 - 10 - ns TE2LDX VCC = 4.5V and 5.5V 9, 10, 11 -55oC ≤ TA ≤ +125oC 10 - 10 - 10 - ns NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume transition time ≤ 5ns; input levels = 0.0V to 3.0V; timing reference levels = 1.5V; output load = 1TTL equivalent load and CL ≥ 50pF, for CL > 50pF, access times are derated 0.15ns/pF. TABLE 3. HM-65642/883 ELECTRICAL PERFORMANCE SPECIFICATIONS LIMITS PARAMETER Output High Voltage Input Capacitance I/O Capacitance Write Enable to Output in High Z SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS VOH2 VCC = 4.5V, IO = -100µA 1 -55oC ≤ TA ≤ +125oC VCC -0.4 - V CIN VCC = Open, f = 1MHz, All Measurements Referenced to Device Ground 1, 2 TA = +25oC - 12 pF VCC = Open, f = 1MHz, All Measurements Referenced to Device Ground 1, 3 TA = +25oC - 10 pF VCC = Open, f = 1MHz, All Measurements Referenced to Device Ground 1, 2 TA = +25oC - 14 pF VCC = 4.5V, VI/O = GND or VCC, All Measurements Referenced to Device Ground 1, 3 TA = +25oC - 12 pF 1 -55oC ≤ TA ≤ +125oC - 50 ns 5 - ns CI/O TWLQZ VCC = 4.5V and 5.5V Write Enable High to Output ON TWHQX VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC Chip Enable to Output ON TE1LQX TE2HQX VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC 10 - ns Output Enable to Output ON TGLQX VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC 5 - ns Chip Enable to Output in High Z TE1HQZ VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC - 50 ns 1 -55oC ≤ TA ≤ +125oC - 60 ns TE2LQZ Output Disable to Output in High Z TGHQZ VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC - 50 ns Output Hold from Address Change TAXQX VCC = 4.5V and 5.5V 1 -55oC ≤ TA ≤ +125oC 10 - ns NOTES: 1. The parameters listed in Table 3 are controlled via design or process parameters and are not directly tested. These parameters are characterized upon initial design release and upon design changes which would affect these characteristics. 2. Applies to DIP device types only. For design purposes CIN = 6pF typical and CI/O = 7pF typical. 3. Applies to LCC device types only. For design purposes CIN = 4pF typical and CI/O = 5pF typical. 223 HM-65642/883 TABLE 4. APPLICABLE SUBGROUPS CONFORMANCE GROUPS GROUPS METHOD SUBGROUPS Interim Test 1 100%/5004 - Interim Test 100%/5004 1, 7, 9 PDA 100%/5004 1 Final Test 1 100%/5004 2, 3, 8A, 8B, 10, 11 Group A Samples/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Groups C and D Samples/5005 1, 7, 9 224 HM-65642/883 Low Voltage Data Retention 1. The RAM must be kept disabled during data retention. This is accomplished by holding the E2 pin between -0.3V and GND. Intersil CMOS RAMs are designed with battery backup in mind. Data Retention voltage and supply current are guaranteed over the operating temperature range. The following rules ensure data retention: 2. During power-up and power-down transitions, E2 must be held between -0.3V and 10% of VCC. 3. The RAM can begin operating one TAVAX after VCC reaches the minimum operating voltage of 4.5V. DATA RETENTION MODE VCC 4.5V VIH TAVAX E2 VCCOR GND FIGURE 1. DATA RETENTION Read Cycles TAVAX A ADDRESS 1 TAVQV Q ADDRESS 2 TAXQX DATA 1 DATA 2 FIGURE 2. READ CYCLE I: W, E2 HIGH; G, E1 LOW 225 HM-65642/883 Read Cycles TAVAX A TAVQV E1 TE1LQV TE1HQZ TE1LQX E2 TE2HQV TE2LQZ TE2HQX G TGLQV TGHQZ TGLQX Q FIGURE 3. READ CYCLE II: W HIGH 226 HM-65642/883 Write Cycles TAVAX A TAVWL TWLWH TWHAX W E1 E2 TWHQX TDVWH TWHDX D TWLQZ Q FIGURE 4. WRITE CYCLE I: LATE WRITE TAVAX A TAVE1L TE1LE1H TE1HAX W E1 E2 TDVE1H TE1HDX D FIGURE 5. WRITE CYCLE II: EARLY WRITE - CONTROLLED BY E1 227 HM-65642/883 Write Cycles TAVAX A TAVE2H TE2HE2L TE2LAX W E1 E2 TDVE2L TE2LDX D FIGURE 6. WRITE CYCLE III: EARLY WRITE - CONTROLLED BY E2 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 228 Test Circuit DUT (NOTE 1) CL + - IOH 1.5V IOL EQUIVALENT CIRCUIT NOTE: 1. Test head capacitance. Burn-In Circuits HM-65642/883 CERDIP TOP VIEW HM-65642/883 CLCC TOP VIEW F16 F1 C F15 F10 VCC C GND F2 F2 F2 A0 DQ0 DQ1 DQ2 5 24 6 23 7 22 8 21 9 20 10 11 19 18 12 17 13 16 14 15 A9 A11 G A10 E1 DQ7 DQ6 DQ5 DQ4 DQ3 F9 F11 F8 F12 F7 F14 F6 A5 E2 VCC W 1 32 31 30 29 6 28 A11 7 27 8 26 NC G 25 A10 24 E1 23 DQ7 22 DQ6 21 A2 F4 F0 F3 9 A1 10 A0 11 F2 NC 12 DQ0 13 14 15 16 17 18 19 20 F2 F2 F2 NOTES: NOTES: F0 = 100kHz ±10%. F0 = 100kHz ±10%. All resistors 47kΩ ±5%. C = 0.01µF Min. C = 0.01µF Min. VCC = 5.5V ±0.5V. VCC = 5.5V ±0.5V. VIH = 4.5V ±10%. VIH = 4.5V ±10%. VIL = -0.2V to +0.4V. 229 A9 A3 F13 VIL = -0.2V to +0.4V. A8 A4 F5 F2 2 3 5 F0 F2 NC 4 NC A6 A12 A7 F16 F2 GND 25 A8 F1 F2 F3 A1 4 E2 DQ5 F4 A2 26 F2 F5 A3 3 W DQ4 F6 A4 27 F2 F7 A5 2 NC DQ3 F8 A6 28 GND F9 A7 1 F2 F10 A12 DQ2 F15 VCC DQ1 NC F11 F12 F14 F0 F13 F0 F2 F2 Die Characteristics DIE DIMENSIONS: 274.0 x 302.8 x 19 ±1mils GLASSIVATION: Type: SiO2 Thickness: 8kÅ ±1kÅ METALLIZATION: Type: Si - Al Thickness: 11kÅ ±2kÅ WORST CASE CURRENT DENSITY: 0.9 x 105 A/cm2 Metallization Mask Layout HM-65642/883 A8 A7 A12 VCC W E2 A8 A5 A4 A3 A9 A11 A2 A1 A0 A10 G E1 DQ7 DQ0 DQ1 DQ2 GND DQ3 DQ4 DQ5 DQ6 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 230