64Mb Synchronous DRAM based on 1M x 4Bank x16 I/O Document Title 4Bank x 1M x 16bits Synchronous DRAM Revision History Revision No. History Draft Date Remark First Version Release 1.0 1. Changed tOH: 2.0 --> 2.5 [tCK = 7 & 7.5 (CL3) Product] Nov. 2004 1.1 1. Changed Input High/Low Voltage (Page 08) 2. Changed DC characteristics (Page 09) - IDD2NS: 18mA -> 15mA - IDD5:210 / 195 / 180mA -> 170 / 160 / 150mA [Speed 200 / 166 / 143 / 133MHz] 3. Changed Clock High / Low pulse width Time (Page 11) 4. Changed tAC Time (Page11) 5. Changed tRRD Time (Page12) 1.2 1. Corrected Revision No.: 2.0 -> 1.1 2. Deleted Remark at Revision History 3. Corrected AC OPERATING CONDITION - CL 50pF -> 30pF 4. Changed DC OPERATING CONDITION - VIH MAX VDDQ+2.0 -> VDDQ+0.3 and Typ 3.3 -> 3.0 - VIL MIN VSSQ-2.0 -> -0.3 1.3 1. Modified note for Super Low Power in ORDERING INFORMATION Jan. 2005 1.4 1. Corrected PIN ASSIGNMENT A12 to NC Jan. 2005 1.5 1. Corrected comments for overshoot and undershoot Feb. 2005 Dec. 2004 Dec. 2004 This document is a general product description and is subject to change without notice. Hynix does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 1.5 / Feb. 2005 1 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series DESCRIPTION The Hynix HY57V641620E(L/S)T(P) series is a 67,108,864bit CMOS Synchronous DRAM, ideally suited for the memory applications which require wide data I/O and high bandwidth. HY57V641620E(L/S)T(P) is organized as 4banks of 1,048,576x16. HY57V641620E(L/S)T(P) is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL. Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipelined design is not restricted by a '2N' rule) FEATURES • Voltage: VDD, VDDQ 3.3V supply voltage • Auto refresh and self refresh • All device pins are compatible with LVTTL interface • 4096 Refresh cycles / 64ms • 54 Pin TSOPII (Lead or Lead Free Package) • Programmable Burst Length and Burst Type • All inputs and outputs referenced to positive edge of system clock • Data mask function by UDQM, LDQM • Internal four banks operation - 1, 2, 4, 8 or full page for Sequential Burst - 1, 2, 4 or 8 for Interleave Burst • Programmable CAS Latency; 2, 3 Clocks • Burst Read Single Write operation ORDERING INFORMATION Part No. Clock Frequency HY57V641620E(L/S)T(P)-5 200MHz HY57V641620E(L/S)T(P)-6 166MHz HY57V641620E(L/S)T(P)-7 143MHz HY57V641620E(L/S)T(P)-H 133MHz Organization Interface Package 4Banks x 1Mbits x16 LVTTL 54 Pin TSOPII Note: 1. HY57V641620ET Series: Normal power, Leaded. 2. HY57V641620ELT Series: Low power, Leaded. 3. HY57V641620EST Series: Super Low power, Leaded. 4. HY57V641620ETP Series: Normal power, Lead Free. 5. HY57V641620ELTP Series: Low power, Lead Free. 6. HY57V641620ESTP Series: Super Low Power, Lead Free Rev. 1.5 / Feb. 2005 2 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series PIN ASSIGNMENTS VDD 1 54 VSS DQ0 2 53 DQ15 VDDQ 3 52 VSSQ DQ1 4 51 DQ14 DQ2 5 50 DQ13 VSSQ 6 49 VDDQ DQ3 7 48 DQ12 DQ4 8 47 DQ11 VDDQ 9 46 VSSQ DQ5 10 45 DQ10 DQ6 11 44 DQ9 VSSQ 12 43 VDDQ DQ7 13 42 DQ8 VDD 14 41 VSS LDQM 15 40 NC /WE 16 39 UDQM /CAS 17 38 CLK /RAS 18 37 CKE /CS 19 36 NC BA0 20 35 A11 BA1 21 34 A9 A10/AP 22 33 A8 A0 23 32 A7 A1 24 31 A6 A2 25 30 A5 A3 26 29 A4 VDD 27 28 VSS Rev. 1.5 / Feb. 2005 54 Pin TSOPII 400mil x 875mil 0.8mm pin pitch 3 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series PIN DESCRIPTION SYMBOL TYPE CLK Clock CKE Clock Enable CS Chip Select BA0, BA1 Bank Address A0 ~ A11 Address RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable RAS, CAS and WE define the operation Refer function truth table for details UDQM, LDQM Data Input/Output Mask Controls output buffers in read mode and masks input data in write mode DQ0 ~ DQ15 Data Input / Output VDD / VSS Power Supply / Ground VDDQ / VSSQ Data Output Power / Ground NC No Connection Rev. 1.5 / Feb. 2005 DESCRIPTION The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh Enables or disables all inputs except CLK, CKE, UDQM and LDQM Selects bank to be activated during RAS activity Selects bank to be read/written during CAS activity Row Address: RA0 ~ RA11, Column Address: CA0 ~ CA7 Auto-precharge flag: A10 Multiplexed data input / output pin Power supply for internal circuits and input buffers Power supply for output buffers No connection 4 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series FUNCTIONAL BLOCK DIAGRAM 1Mbit x 4banks x 16 I/O Synchronous DRAM Internal Row Counter Self refresh logic & timer 1Mx16 BANK 3 CLK CAS Column Active U/LDQM A0 Address Buffers BA1 DQ0 DQ15 Y-Decoder Column Add Counter Bank Select A11 Memory Cell Array Column Pre Decoder WE A1 1Mx16 BANK 0 I/O Buffer & Logic Refresh 1Mx16 BANK 1 Sense AMP & I/O Gate State Machine RAS 1Mx16 BANK 2 X-Decoder X-Decoder X-Decoder X-Decoder CKE CS Row Pre Decoder Row Active Address Register Mode Register Burst Counter CAS Latency Data Out Control Pipe Line Control BA0 Rev. 1.5 / Feb. 2005 5 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series BASIC FUNCTIONAL DESCRIPTION Mode Register BA1 BA0 A11 A10 A9 A8 A7 0 0 0 0 OP Code 0 0 A6 A5 A4 A3 CAS Latency A2 BT A1 A0 Burst Length OP Code A9 Write Mode 0 Burst Read and Burst Write 1 Burst Read and Single Write CAS Latency Burst Type A3 Burst Type 0 Sequential 1 Interleave Burst Length A6 A5 A4 CAS Latency 0 0 0 Reserved 0 0 1 0 1 0 1 1 0 1 0 Burst Length A2 A1 A0 A3 = 0 A3=1 1 0 0 0 1 1 0 2 0 0 1 2 2 1 3 0 1 0 4 4 0 Reserved 0 1 1 8 8 1 Reserved 1 0 0 Reserved Reserved 1 1 0 Reserved 1 0 1 Reserved Reserved 1 1 1 Reserved 1 1 0 Reserved Reserved 1 1 1 Full Page Reserved Rev. 1.5 / Feb. 2005 6 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series ABSOLUTE MAXIMUM RATING Parameter Symbol Rating Unit Ambient Temperature TA 0 ~ 70 oC Storage Temperature TSTG -55 ~ 125 Voltage on Any Pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VDD relative to VSS VDD, VDDQ -1.0 ~ 4.6 V Short Circuit Output Current IOS 50 mA Power Dissipation PD 1 W TSOLDER 260 / 10 Soldering Temperature / Time o oC C / Sec DC OPERATING CONDITION (TA= 0 to 70oC) Parameter Symbol Min Typ Max Unit Note VDD, VDDQ 3.0 3.3 3.6 V 1 Input High Voltage VIH 2.0 3.0 V 1, 2 Input Low Voltage VIL -0.3 - V 1, 3 Power Supply Voltage VDDQ + 0.3 0.8 Note: 1. All voltages are referenced to VSS = 0V 2. VIH(max) is acceptable 5.6V AC pulse width with <=3ns of duration. 3. VIL(min) is acceptable -2.0V AC pulse width with <=3ns of duration. AC OPERATING TEST CONDITION (TA= 0 to 70 oC, VDD=3.3±0.3V, VSS=0V) Parameter Symbol Value Unit VIH / VIL 2.4 / 0.4 V Vtrip 1.4 V Input Rise/Fall Time tR / tF 1 ns Output Timing Measurement Reference Level Voltage Voutref 1.4 V CL 30 pF AC Input High/Low Level Voltage Input Timing Measurement Reference Level Voltage Output Load Capacitance for Access Time Measurement Note: 1. Vtt=1.4V RT=50 Ω Output Z0 = 50Ω 30pF DC Output Load Circuit Rev. 1.5 / Feb. 2005 1 Vtt=1.4V RT=500 Ω Output Note 30pF AC Output Load Circuit 7 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series CAPACITANCE (TA= 0 to 70 oC, f=1MHz, VDD=3.3V) Parameter Input capacitance Data input / output capacitance Pin Symbol Min Max Unit CLK CI1 2.0 4.0 pF A0 ~ A11, BA0, BA1, CKE, CS, RAS, CAS, WE, LDQM, UDQM CI2 2.5 5.0 pF DQ0 ~ DQ15 CI/O 3.0 5.5 pF DC CHARACTERRISTICS I (TA= 0 to 70oC) Parameter Symbol Min Max Unit Note Input Leakage Current ILI -1 1 uA 1 Output Leakage Current ILO -1 1 uA 2 Output High Voltage VOH 2.4 - V IOH = -4mA Output Low Voltage VOL - 0.4 V IOL = +4mA Note: 1. VIN = 0 to 3.3V, All other balls are not tested under VIN =0V 2. DOUT is disabled, VOUT=0 to 3.6 Rev. 1.5 / Feb. 2005 8 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series DC CHARACTERISTICS II (TA= 0 to 70oC) Parameter Operating Current Symbol IDD1 Speed Test Condition 5 Burst length=1, One bank active tRC ≥ tRC(min), IOL=0mA 6 7 H Unit Note 120 110 100 100 mA CKE ≤ VIL(max), tCK = 15ns 2 mA CKE ≤ VIL(max), tCK = ∞ 2 mA CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 18 CKE ≥ VIH(min), tCK = ∞ Input signals are stable. 15 IDD3P CKE ≤ VIL(max), tCK = 15ns 3 IDD3PS CKE ≤ VIL(max), tCK = ∞ 3 IDD3N CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 40 IDD3NS CKE ≥ VIH(min), tCK = ∞ Input signals are stable. 35 Burst Mode Operating Current IDD4 tCK ≥ tCK(min), IOL=0mA All banks active 120 110 100 100 mA 1 Auto Refresh Current IDD5 tRC ≥ tRC(min), All banks active 170 160 150 150 mA 2 Normal 1 mA Low power 400 uA Super Low power 300 uA Precharge Standby Cur- IDD2P rent IDD2PS in Power Down Mode Precharge Standby Cur- IDD2N rent in Non Power Down Mode IDD2NS Active Standby Current in Power Down Mode Active Standby Current in Non Power Down Mode 1 mA mA mA 3 Self Refresh Current IDD6 CKE ≤ 0.2V 3, 4 Note: 1. IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open 2. Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS II 3. HY57V641620ET(P) Series: Normal Power HY57V641620ELT(P) Series: Low Power HY57V641620EST(P) Series: Super Low Power Rev. 1.5 / Feb. 2005 9 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series AC CHARACTERISTICS I (AC operating conditions unless otherwise noted) Parameter Symbol 5 Min 6 Max Min Max Min Max Min Unit Note 5.0 CL = 2 tCK2 10 Clock High Pulse Width tCHW 1.75 - 2.0 - 2.0 - 2.5 - ns 1 Clock Low Pulse Width tCLW 1.75 - 2.0 - 2.0 - 2.5 - ns 1 CL = 3 tAC3 - 4.5 - 5.4 - 5.4 - 5.4 ns CL = 2 tAC2 - 6.0 - 6.0 - 6.0 - 6.0 ns Data-out Hold Time tOH 2.0 - 2.0 - 2.5 - 2.5 - ns Data-Input Setup Time tDS 1.5 - 1.5 - 1.5 - 1.5 - ns 1 Data-Input Hold Time tDH 0.8 - 0.8 - 0.8 - 0.8 - ns 1 Address Setup Time tAS 1.5 - 1.5 - 1.5 - 1.5 - ns 1 Address Hold Time tAH 0.8 - 0.8 - 0.8 - 0.8 - ns 1 CKE Setup Time tCKS 1.5 - 1.5 - 1.5 - 1.5 - ns 1 CKE Hold Time tCKH 0.8 - 0.8 - 0.8 - 0.8 - ns 1 Command Setup Time tCS 1.5 - 1.5 - 1.5 - 1.5 - ns 1 Command Hold Time tCH 0.8 - 0.8 - 0.8 - 0.8 - ns 1 1.0 - 1.0 - 1.5 - 1.5 - ns Access Time From Clock CLK to Data Output in Low-Z Time tOLZ CLK to Data Output in High-Z Time 10 1000 10 1000 7.5 Max tCK3 1000 7.0 H CL = 3 System Clock Cycle Time 6.0 7 10 1000 ns ns CL = 3 tOHZ3 - 4.5 - 5.4 - 5.4 - 5.4 ns CL = 2 tOHZ2 - 6.0 - 6.0 - 6.0 - 6.0 ns 2 Note: 1. Assume tR / tF (input rise and fall time) is 1ns. If tR & tF > 1ns, then [(tR+tF)/2-1]ns should be added to the parameter. 2. Access time to be measured with input signals of 1V/ns edge rate, from 0.8V to 0.2V. If tR > 1ns, then (tR/2-0.5)ns should be added to the parameter. Rev. 1.5 / Feb. 2005 10 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series AC CHARACTERISTICS II (AC operating conditions unless otherwise noted) Parameter Symbol 5 6 7 H Unit Note Min Max Min Max Min Max Min Max 55 - 60 - 63 - 63 - ns RAS Cycle Time Operation RAS Cycle Time Auto Refresh tRRC 55 - 60 - 63 - 63 - ns RAS to CAS Delay tRCD 15 - 18 - 20 - 20 - ns RAS Active Time tRAS 38.7 100K 42 100K 42 100K 42 120K ns RAS Precharge Time tRP 15 - 18 - 20 - 20 - ns RAS to RAS Bank Active Delay tRRD 10 - 12 - 14 - 15 - ns CAS to CAS Delay tCCD 1 - 1 - 1 - 1 - CLK Write Command to Data-In DetWTL lay 0 - 0 - 0 - 0 - CLK Data-in to Precharge Command tDPL 2 - 2 - 2 - 2 - CLK tRC Data-In to Active Command tDAL DQM to Data-Out Hi-Z tDQZ 2 - 2 - 2 - 2 - CLK DQM to Data-In Mask tDQM 0 - 0 - 0 - 0 - CLK MRS to New Command tMRD 2 - 2 - 2 - 2 - CLK Precharge to Data CL = 3 Output High-Z CL = 2 tPROZ3 3 - 3 - 3 - 3 - CLK tPROZ2 2 - 2 - 2 - 2 - CLK Power Down Exit Time tDPE 1 - 1 - 1 - 1 - CLK Self Refresh Exit Time tSRE 1 - 1 - 1 - 1 - CLK Refresh Time tREF - 64 - 64 - 64 - 64 ms tDPL + tRP 1 Note: 1. A new command can be given tRRC after self refresh exit. Rev. 1.5 / Feb. 2005 11 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series COMMAND TRUTH TABLE Command CKEn-1 CKEn CS RAS CAS WE DQM ADDR Mode Register Set H X L L L L X OP code No Operation H X H X X X L H H H X X Bank Active H X L L H H X RA Read Read with charge BA Autopre- H X L H L H X CA V H V L Autopre- H X L H L L X CA Precharge All Banks V H X L V X L L H L X Burst Stop H X L H H L X X DQM H V X Auto Refresh H H L L L H X X Burst-Read-SingleWRITE H X L L L L X A9 ball High (Other balls OP code) Entry H L L L L H X Exit L H H X X X L H H H Entry H L H X X X L H H H H X X X L H H H H X X X L V V V Self Refresh1 selected X Precharge power down Clock Suspend Exit L H Entry H L Exit L H Rev. 1.5 / Feb. 2005 X X X H H Precharge Bank Note L Write Write with charge A10/AP MRS Mode X X X X X X X 12 Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620E(L/S)T(P) Series PACKAGE INFORMATION 400mil 54pin Thin Small Outline Package UNIT : mm(inch) 11.938(0.4700) 11.735(0.4620) 22.327(0.8790) 22.149(0.8720) 10.262(0.4040) 10.058(0.3960) 0.150(0.0059) 0.050(0.0020) 0.80(0.0315)BSC Rev. 1.5 / Feb. 2005 0.400(0.016) 0.300(0.012) 1.194(0.0470) 0.991(0.0390) 5deg 0deg 0.597(0.0235) 0.406(0.0160) 0.210(0.0083) 0.120(0.0047) 13