LATTICE PLSI1032-60LJ

Specifications ispLSI and pLSI 1032
ispLSI and pLSI 1032
®
®
High-Density Programmable Logic
Features
Functional Block Diagram
• HIGH-DENSITY PROGRAMMABLE LOGIC
— High Speed Global Interconnect
— 6000 PLD Gates
— 64 I/O Pins, Eight Dedicated Inputs
— 192 Registers
— Wide Input Gating for Fast Counters, State
Machines, Address Decoders, etc.
— Small Logic Block Size for Fast Random Logic
— Security Cell Prevents Unauthorized Copying
• HIGH PERFORMANCE E2CMOS® TECHNOLOGY
— fmax = 90 MHz Maximum Operating Frequency
— fmax = 60 MHz for Industrial and Military/883 Devices
— tpd = 12 ns Propagation Delay
— TTL Compatible Inputs and Outputs
— Electrically Erasable and Reprogrammable
— Non-Volatile E2CMOS Technology
— 100% Tested
• ispLSI OFFERS THE FOLLOWING ADDED FEATURES
— In-System Programmable™ (ISP™) 5-Volt Only
— Increased Manufacturing Yields, Reduced Time-toMarket, and Improved Product Quality
— Reprogram Soldered Devices for Faster Prototyping
• COMBINES EASE OF USE AND THE FAST SYSTEM
SPEED OF PLDs WITH THE DENSITY AND FLEXIBILITY OF FIELD PROGRAMMABLE GATE ARRAYS
— Complete Programmable Device Can Combine Glue
Logic and Structured Designs
— Four Dedicated Clock Input Pins
— Synchronous and Asynchronous Clocks
— Flexible Pin Placement
— Optimized Global Routing Pool Provides Global
Interconnectivity
• ispLSI AND pLSI DEVELOPMENT TOOLS
pDS® Software
— Easy to Use PC Windows™ Interface
— Boolean Logic Compiler
— Manual Partitioning
— Automatic Place and Route
— Static Timing Table
ispDS+™ Software
— Industry Standard, Third Party Design
Environments
— Schematic Capture, State Machine, HDL
— Automatic Partitioning and Place and Route
— Comprehensive Logic and Timing Simulation
— PC and Workstation Platforms
Output Routing Pool
D7 D6 D5 D4 D3 D2 D1 D0
Output Routing Pool
C6
D Q
A1
A2
Logic
A3
Array
C5
D Q
D Q
GLB
C4
C3
A4
D Q
A5
C2
A6
C1
A7
Global Routing Pool (GRP)
B0 B1 B2 B3 B4 B5 B6 B7
Output Routing Pool
C7
A0
C0
CLK
Output Routing Pool
Description
The ispLSI and pLSI 1032 are High-Density Programmable Logic Devices containing 192 Registers, 64
Universal I/O pins, eight Dedicated Input pins, four Dedicated Clock Input pins and a Global Routing Pool (GRP).
The GRP provides complete interconnectivity between
all of these elements. The ispLSI 1032 features 5-Volt insystem programming and in-system diagnostic
capabilities. It is the first device which offers non-volatile
"on-the-fly" reprogrammability of the logic, as well as the
interconnect to provide truly reconfigurable systems. It is
architecturally and parametrically compatible to the pLSI
1032 device, but multiplexes four of the dedicated input
pins to control in-system programming.
The basic unit of logic on the ispLSI and pLSI 1032
devices is the Generic Logic Block (GLB). The GLBs are
labeled A0, A1 .. D7 (see figure 1). There are a total of
32 GLBs in the ispLSI and pLSI 1032 devices. Each GLB
has 18 inputs, a programmable AND/OR/XOR array, and
four outputs which can be configured to be either combinatorial or registered. Inputs to the GLB come from the
GRP and dedicated inputs. All of the GLB outputs are
brought back into the GRP so that they can be connected
to the inputs of any other GLB on the device.
Copyright © 1997 Lattice Semiconductor Corp. All brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject
to change without notice.
LATTICE SEMICONDUCTOR CORP., 5555 Northeast Moore Ct., Hillsboro, Oregon 97124, U.S.A.
Tel. (503) 681-0118; 1-800-LATTICE; FAX (503) 681-3037; http://www.latticesemi.com
1032_02
1
February 1997
1996 ISP Encyclopedia
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Functional Block Diagram
Figure 1. ispLSI and pLSI 1032 Functional Block Diagram
I/O I/O I/O I/O
63 62 61 60
I/O I/O I/O I/O
59 58 57 56
I/O I/O I/O I/O
55 54 53 52
I/O I/O I/O I/O
51 50 49 48
IN IN
7 6
RESET
Input Bus
Generic
Logic Blocks
(GLBs)
Output Routing Pool (ORP)
D7
D6
D5
D4
D3
D2
D1
IN 5
IN 4
D0
I/O 47
I/O 46
I/O 45
C7
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
C5
A2
C4
Global
Routing
Pool
(GRP)
A3
C3
A4
C2
A5
I/O 44
I/O 43
I/O 42
I/O 41
lnput Bus
Output Routing Pool (ORP)
I/O 8
C6
A1
Input Bus
I/O 4
I/O 5
I/O 6
I/O 7
A0
Output Routing Pool (ORP)
I/O 0
I/O 1
I/O 2
I/O 3
I/O 40
I/O 39
I/O 38
I/O 37
I/O 36
C1
A6
I/O 35
I/O 34
I/O 33
I/O 32
C0
A7
*SDI/IN 0
*MODE/IN 1
B0
B1
B2
B3
B4
B5
B6
B7
Clock
Distribution
Network
Output Routing Pool (ORP)
Megablock
CLK 0
CLK 1
CLK 2
IOCLK 0
IOCLK 1
Input Bus
*ispEN/NC
*SDO/IN 2
*SCLK/IN 3
I/O I/O I/O I/O
16 17 18 19
I/O I/O I/O I/O
20 21 22 23
I/O I/O I/O I/O
24 25 26 27
I/O I/O I/O I/O
28 29 30 31
Y Y Y Y
0 1 2 3
0139(1)-32-isp
*ISP Control Functions for ispLSI 1032 Only
The devices also have 64 I/O cells, each of which is
directly connected to an I/O pin. Each I/O cell can be
individually programmed to be a combinatorial input,
registered input, latched input, output or bi-directional
I/O pin with 3-state control. Additionally, all outputs are
polarity selectable, active high or active low. The signal
levels are TTL compatible voltages and the output drivers
can source 4 mA or sink 8 mA.
The GRP has as its inputs the outputs from all of the GLBs
and all of the inputs from the bi-directional I/O cells. All of
these signals are made available to the inputs of the
GLBs. Delays through the GRP have been equalized to
minimize timing skew.
Clocks in the ispLSI and pLSI 1032 devices are selected
using the Clock Distribution Network. Four dedicated
clock pins (Y0, Y1, Y2 and Y3) are brought into the
distribution network, and five clock outputs (CLK 0, CLK
1, CLK 2, IOCLK 0 and IOCLK 1) are provided to route
clocks to the GLBs and I/O cells. The Clock Distribution
Network can also be driven from a special clock GLB (C0
on the ispLSI and pLSI 1032 devices). The logic of this
GLB allows the user to create an internal clock from a
combination of internal signals within the device.
Eight GLBs, 16 I/O cells, two dedicated inputs and one
ORP are connected together to make a Megablock (see
figure 1). The outputs of the eight GLBs are connected to
a set of 16 universal I/O cells by the ORP. The I/O cells
within the Megablock also share a common Output
Enable (OE) signal. The ispLSI and pLSI 1032 devices
contain four of these Megablocks.
2
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Absolute Maximum Ratings 1
Supply Voltage Vcc ...................................-0.5 to +7.0V
Input Voltage Applied ........................ -2.5 to VCC +1.0V
Off-State Output Voltage Applied ..... -2.5 to VCC +1.0V
Storage Temperature ................................ -65 to 150°C
Case Temp. with Power Applied .............. -55 to 125°C
Max. Junction Temp. (TJ) with Power Applied ... 150°C
1. Stresses above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional
operation of the device at these or at any other conditions above those indicated in the operational sections of this specifica tion
is not implied (while programming, follow the programming specifications).
DC Recommended Operating Conditions
SYMBOL
VCC
PARAMETER
Supply Voltage
MIN.
MAX.
Commercial
TA = 0°C to +70°C
4.75
5.25
Industrial
TA = -40°C to +85°C
4.5
5.5
Military/883
TC = -55°C to +125°C
4.5
5.5
UNITS
V
VIL
Input Low Voltage
0
0.8
V
VIH
Input High Voltage
2.0
Vcc + 1
V
Table 2- 0005Aisp w/mil.eps
Capacitance (TA=25oC, f=1.0 MHz)
SYMBOL
C1
C2
MAXIMUM1
UNITS
TEST CONDITIONS
Commercial/Industrial
8
pf
V CC=5.0V, VIN=2.0V
Military
10
pf
V CC=5.0V, VIN=2.0V
10
pf
V CC=5.0V, VI/O, VY=2.0V
PARAMETER
Dedicated Input Capacitance
I/O and Clock Capacitance
Table 2- 0006
1. Guaranteed but not 100% tested.
Data Retention Specifications
PARAMETER
MINIMUM
MAXIMUM
UNITS
20
–
Years
10000
–
Cycles
100
–
Cycles
Data Retention
ispLSI Erase/Reprogram Cycles
pLSI Erase/Reprogram Cycles
Table 2- 0008B
3
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Switching Test Conditions
Input Pulse Levels
Figure 2. Test Load
GND to 3.0V
≤ 3ns 10% to 90%
Input Rise and Fall Time
Input Timing Reference Levels
1.5V
Output Timing Reference Levels
1.5V
Output Load
+ 5V
R1
See figure 2
Device
Output
3-state levels are measured 0.5V from steady-state
active level.
Test
Point
Table 2- 0003
CL*
R2
Output Load Conditions (see figure 2)
*CL includes Test Fixture and Probe Capacitance.
Test Condition
R1
R2
CL
470Ω
390Ω
35pF
Active High
∞
390Ω
35pF
Active Low
470Ω
390Ω
35pF
Active High to Z
at VOH - 0.5V
∞
390Ω
5pF
Active Low to Z
470Ω
390Ω
5pF
A
B
C
at VOL + 0.5V
DC Electrical Characteristics
Over Recommended Operating Conditions
SYMBOL
1.
2.
3.
4.
PARAMETER
CONDITION
MIN.
TYP.3
MAX.
0.4
V
VOL
VOH
IIL
IIH
IIL-isp
IIL-PU
IOS1
Output Low Voltage
IOL =8 mA
–
–
Output High Voltage
IOH =-4 mA
ICC2,4
UNITS
2.4
–
–
V
Input or I/O Low Leakage Current 0V ≤ VIN ≤ VIL (MAX.)
–
–
-10
µA
Input or I/O High Leakage Current 3.5V ≤ VIN ≤ VCC
–
–
10
µA
isp Input Low Leakage Current
0V ≤ VIN ≤ VIL (MAX.)
–
–
-150
µA
I/O Active Pull-Up Current
0V ≤ VIN ≤ VIL
–
–
-150
µA
Output Short Circuit Current
VCC = 5V, VOUT = 0.5V
–
–
-200
mA
Operating Power Supply Current
VIL = 0.5V, VIH = 3.0V Commercial
–
130
190
mA
fTOGGLE = 1 MHz
–
135
220
mA
Industrial/Military
One output at a time for a maximum duration of one second.
Measured using eight 16-bit counters.
Typical values are at VCC = 5V and TA = 25oC.
Maximum ICC varies widely with specific device configuration and operating frequency. Refer to the Power Consumption secTable 2- 0007A-32-isp
tion of this datasheet and Thermal Management section of this Data Book to estimate maximum ICC.
4
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
External Timing Parameters
Over Recommended Operating Conditions
5 2
PARAMETER TEST #
COND.
1.
2.
3.
4.
5.
-80
-60
UNITS
MIN. MAX. MIN. MAX. MIN. MAX.
Data Propagation Delay, 4PT bypass, ORP bypass
A
2
A
3
–
4
12
Data Propagation Delay, Worst Case Path
–
Clock Frequency with Internal Feedback3
90.9
Clock Frequency with External Feedback (tsu2 1+ tco1)
58.8
–
5
Clock Frequency, Max
Toggle 4
–
6
GLB Reg. Setup Time before Clock, 4PT bypass
A
7
GLB Reg. Clock to Output Delay, ORP bypass
–
8
GLB Reg. Hold Time after Clock, 4 PT bypass
–
9
GLB Reg. Setup Time before Clock
–
10 GLB Reg. Clock to Output Delay
–
11 GLB Reg. Hold Time after Clock
A
12 Ext. Reset Pin to Output Delay
–
13 Ext. Reset Pulse Duration
B
14 Input to Output Enable
C
15 Input to Output Disable
–
–
20
20
–
25
ns
–
60
–
MHz
–
38
–
MHz
–
83
–
MHz
7
–
9
–
ns
–
10
–
13
ns
0
–
0
–
ns
10
–
13
–
ns
–
12
–
16
ns
0
–
0
–
ns
–
17
–
22.5
ns
10
–
13
–
ns
–
18
–
24
ns
–
18
–
24
ns
6
–
ns
–
15
17
–
–
80
–
50
S
–
125
–
6
–
–
8
0
–
9
–
–
10
0
–
–
15
S
1
USE 1032E-70
FOR NEW DESIG
N
A
USE 1032E-80
FOR NEW DESIG
N
tpd1
tpd2
fmax (Int.)
fmax (Ext.)
fmax (Tog.)
tsu1
tco1
th1
tsu2
tco2
th2
tr1
trw1
ten
tdis
twh
twl
tsu5
th5
-90
DESCRIPTION1
100
ns
10
–
–
15
–
15
16 Ext. Sync. Clock Pulse Duration, High
4
–
5
–
–
17 Ext. Sync. Clock Pulse Duration, Low
4
–
5
–
6
–
ns
–
18 I/O Reg. Setup Time before Ext. Sync. Clock (Y2, Y3)
2
–
2
–
2.5
–
ns
–
19 I/O Reg. Hold Time after Ext. Sync. Clock (Y2, Y3)
6.5
–
6.5
–
8.5
–
ns
Unless noted otherwise, all parameters use a GRP load of 4 GLBs, ORP and Y0 clock.
Refer to Timing Model in this data sheet for further details.
Standard 16-Bit counter using GRP feedback.
fmax (Toggle) may be less than 1/(twh + twl). This is to allow for a clock duty cycle of other than 50%.
Reference Switching Test Conditions section.
5
Table 2-0030-32/90,80,60C
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Internal Timing Parameters1
GRP
tgrp1
tgrp4
tgrp8
tgrp12
tgrp16
tgrp32
GLB
t4ptbp
t1ptxor
t20ptxor
txoradj
tgbp
tgsu
tgh
tgco
tgr
tptre
tptoe
tptck
ORP
torp
torpbp
-90
DESCRIPTION
-80
-60
UNITS
MIN. MAX. MIN. MAX. MIN. MAX.
–
2.0
2.4
–
–
5.5
–
1.0
–
2.4
–
2.8
–
3.2
–
1.2
–
1.6
–
2.4
–
3.0
–
3.6
–
6.4
–
5.2
–
5.7
–
7.0
–
8.2
–
1.6
–
4.8
20
I/O Register Bypass
21
I/O Latch Delay
22
I/O Register Setup Time before Clock
23
I/O Register Hold Time after Clock
2.1
24
I/O Register Clock to Out Delay
25
I/O Register Reset to Out Delay
26
Dedicated Input Delay
27
GRP Delay, 1 GLB Load
28
GRP Delay, 4 GLB Loads
29
GRP Delay, 8 GLB Loads
30
GRP Delay, 12 GLB Loads
31
GRP Delay, 16 GLB Loads
32
GRP Delay, 32 GLB Loads
33
4 Product Term Bypass Path Delay
–
2.7
ns
3.0
–
4.0
ns
–
7.3
–
ns
–
1.3
–
ns
–
3.0
–
4.0
ns
–
2.5
–
3.3
ns
–
4.0
–
5.3
ns
–
1.5
–
2.0
ns
–
2.0
–
2.7
ns
–
3.0
–
4.0
ns
–
3.8
–
5.0
ns
–
4.5
–
6.0
ns
–
8.0
–
10.6
ns
–
6.5
–
8.6
ns
–
7.0
–
9.3
ns
–
8.0
–
10.6
ns
–
9.5
–
12.7
ns
36
XOR Adjacent Path
37
GLB Register Bypass Delay
–
0.8
–
1.0
–
1.3
ns
38
GLB Register Setup Time before Clock
1.2
–
1.0
–
1.3
–
ns
39
GLB Register Hold Time after Clock
3.6
–
4.5
–
6.0
–
ns
40
GLB Register Clock to Output Delay
–
1.6
–
2.0
–
2.7
ns
41
GLB Register Reset to Output Delay
–
2.0
USE 1032E-70 FO
R NEW DESIGNS
Inputs
tiobp
tiolat
tiosu
tioh
tioco
tior
tdin
2
#
USE 1032E-80 FO
R NEW DESIGNS
PARAMETER
–
2.5
–
3.3
ns
42
GLB Product Term Reset to Register Delay
–
8.0
–
10.0
–
13.3
ns
43
GLB Product Term Output Enable to I/O Cell Delay
–
7.8
–
9.0
–
12.0
ns
44
GLB Product Term Clock Delay
2.8
6.0
3.5
7.5
4.6
9.9
ns
45
ORP Delay
–
2.4
–
2.5
–
3.3
ns
46
ORP Bypass Delay
–
0.4
–
0.5
–
0.7
ns
34
1 Product Term/XOR Path Delay
35
20 Product Term/XOR Path Delay
Delay3
1. Internal Timing Parameters are not tested and are for reference only.
2. Refer to Timing Model in this data sheet for further details.
3. The XOR adjacent path can only be used by hard macros.
6
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Internal Timing Parameters1
Outputs
tob
toen
todis
Clocks
tgy0
tgy1/2
tgcp
tioy2/3
tiocp
2
#
-90
DESCRIPTION
-60
UNITS
MIN. MAX. MIN. MAX. MIN. MAX.
47
Output Buffer Delay
48
I/O Cell OE to Output Enabled
49
I/O Cell OE to Output Disabled
50
Clock Delay, Y0 to Global GLB Clock Line (Ref. clock)
51
Clock Delay, Y1 or Y2 to Global GLB Clock Line
52
Clock Delay, Clock GLB to Global GLB Clock Line
53
Clock Delay, Y2 or Y3 to I/O Cell Global Clock Line
54
Clock Delay, Clock GLB to I/O Cell Global Clock Line
Global Reset
tgr
55
-80
Global Reset to GLB and I/O Registers
USE 1032E-8
FOR NEW DE 0
SIGNS
USE 1032E-7
FOR NEW DE 0
SIGNS
PARAMETER
–
2.4
–
3.0
–
4.0
ns
–
4.0
–
5.0
–
6.7
ns
–
4.0
–
5.0
–
6.7
ns
3.6
3.6
4.5
4.5
6.0
6.0
ns
2.8
4.4
3.5
5.5
4.6
7.3
ns
0.8
4.0
1.0
5.0
1.3
6.6
ns
2.8
4.4
3.5
5.5
4.6
7.3
ns
0.8
4.0
1.0
5.0
1.3
6.6
ns
–
8.2
–
9.0
–
12.0
ns
1. Internal Timing Parameters are not tested and are for reference only.
2. Refer to Timing Model in this data sheet for further details.
7
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
ispLSI and pLSI 1032 Timing Model
I/O Cell
GRP
GLB
ORP
I/O Cell
Feedback
Ded. In
I/O Pin
(Input)
#55
#26
I/O Reg Bypass
4 PT Bypass
GLB Reg Bypass
ORP Bypass
#20
#28
#33
#37
#46
Input
D Register Q
RST
#21 - 25
GRP
Loading
Delay
#27, 29,
30, 31, 32
20 PT
XOR Delays
GLB Reg
Delay
ORP
Delay
GRP 4
Clock
Distribution
#51, 52,
53, 54
D
Q
I/O Pin
(Output)
#48, 49
#45
RST
#55
Reset
Y1,2,3
#34, 35, 36
#47
#38, 39,
40, 41
Control RE
PTs
OE
#42, 43, CK
44
#50
Y0
Derivations of tsu, th and tco from the Product Term Clock1
tsu
= Logic + Reg su - Clock (min)
= (tiobp + tgrp4 + t20ptxor) + (tgsu) - (tiobp + tgrp4 + tptck(min))
= (#20 + #28 + #35) + (#38) - (#20 + #28 + #44)
5.5 ns = (2.0 + 2.0 + 8.0) + (1.0) - (2.0 + 2.0 + 3.5)
th
= Clock (max) + Reg h - Logic
= (tiobp + tgrp4 + tptck(max)) + (tgh) - (tiobp + tgrp4 + t20ptxor)
= (#20 + #28 + #44) + (#39) - (#20 + #28 + #35)
4.0 ns = (2.0 + 2.0 + 7.5) + (4.5) - (2.0 + 2.0 + 8.0)
tco
= Clock (max) + Reg co + Output
= (tiobp + tgrp4 + tptck(max)) + (tgco) + (torp + tob)
= (#20 + #28 + #44) + (#40) + (#45 + #47)
19.0 ns = (2.0+ 2.0 +7.5) + (2.0) + (2.5 + 3.0)
Derivations of tsu, th and tco from the Clock GLB1
tsu
= Logic + Reg su - Clock (min)
= (tiobp + tgrp4 + t20ptxor) + (tgsu) - (tgy0(min) + tgco + tgcp(min))
= (#20 + #28 + #35) + (#38) - (#50 + #40 + #52)
5.5 ns = (2.0 + 2.0 + 8.0) + (1.0) - (4.5 + 2.0 + 1.0)
th
= Clock (max) + Reg h - Logic
= (tgy0(max) + tgco + tgcp(max)) + (tgh) - (tiobp + tgrp4 + t20ptxor)
= (#50 + #40 + #52) + (#39) - (#20 + #28 + #35)
4.0 ns = (4.5 + 2.0 + 5.0) + (4.5) - (2.0 + 2.0 + 8.0)
tco
= Clock (max) + Reg co + Output
= (tgy0(max) + tgco + tgcp(max)) + (tgco) + (torp + tob)
= (#50 + #40 + #52) + (#40) + (#45 + #47)
19.0 ns = (4.5 + 2.0 + 5.0) + (2.0) + (2.5 + 3.0)
1. Calculations are based upon timing specifications for the ispLSI and pLSI 1032-80.
8
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Maximum GRP Delay vs GLB Loads
ispLSI and pLSI 1032-60
6
GRP Delay (ns)
5
ispLSI and pLSI 1032-80
4
ispLSI and pLSI 1032-90
3
2
1
0
4
8
GLB Loads
12
16
0126A-80-32-isp
Power Consumption
Power consumption in the ispLSI and pLSI 1032 device
depends on two primary factors: the speed at which the
device is operating, and the number of Product Terms
used. Figure 3 shows the relationship between power
and operating speed.
Figure 3. Typical Device Power Consumption vs fmax
ICC (mA)
250
ispLSI and pLSI 1032
200
150
100
50
0
10
20
30
40
50
60
70
80
fmax (MHz)
Notes: Configuration of eight 16-bit Counters
Typical Current at 5V, 25˚C
ICC can be estimated for the ispLSI and pLSI 1032 using the following equation:
ICC = 52 + (# of PTs * 0.30) + (# of nets * Max. freq * 0.009) where:
# of PTs = Number of Product Terms used in design
# of nets = Number of Signals used in device
Max. freq = Highest Clock Frequency to the device
The ICC estimate is based on typical conditions (VCC = 5.0V, room temperature) and an assumption of 2 GLB loads on
average exists. These values are for estimates only. Since the value of ICC is sensitive to operating conditions and the
program in the device, the actual ICC should be verified.
0127A-32-80-isp
9
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
In-System Programmability
The ispLSI devices are the in-system programmable
versions of the Lattice Semiconductor High-Density programmable Large Scale Integration (pLSI) devices. By
integrating all the high voltage programming circuitry onchip, programming can be accomplished by simply shifting
data into the device. Once the function is programmed,
the non-volatile E2CMOS cells will not lose the pattern
even when the power is turned off.
controls the programming. The interface signals are isp
Enable (ispEN), Serial Data In (SDI), Serial Data Out
(SDO), Serial Clock (SCLK) and Mode (MODE) control.
Figure 4 illustrates the block diagram of one possible
scheme for programming the ispLSI devices. For details
on the operation of the internal state machine and programming of the device please refer to the ISP Architecture
and Programming section in this Data Book.
All necessary programming is done via five TTL level
logic interface signals. These five signals are fed into the
on-chip programming circuitry where a state machine
The device identifier for the ispLSI 1032 is 0000 0011
(03 hex). This code is the unique device identifier which
is generated when a read ID command is performed.
Figure 4. ISP Programming Interface
SDO
SDI
MODE
SCLK
ispEN
5-wire ISP
Programming
Interface
ispEN
SCLK
SCLK
MODE
MODE
ispLSI
SDI
SCLK
MODE
ispGAL
SDO
SDI
ispEN
SCLK
MODE
ispGDS
SDO
SDI
SDO
ispLSI
SDI
SDO
0294B
10
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
ispLSI 1032 Shift Register Layout
D
A
T
A
D
A
T
A
Data In
(SDI)
159...
319...
High Order Shift Register
Low Order Shift Register
...0
...160
SDO
SDI
E2CMOS Cell Array
Address Shift Register
107
.
.
.
.
.
.
0
SDO
Note: A logic "1" in the Address Shift Register bit position enables the row for programming or verification.
A logic "0" disables it.
11
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Description
Name
PLCC Pin Numbers
Description
I/O 0 - I/O 3
I/O 4 - I/O 7
I/O 8 - I/O 11
I/O 12 - I/O 15
I/O 16 - I/O 19
I/O 20 - I/O 23
I/O 24 - I/O 27
I/O 28 - I/O 31
I/O 32 - I/O 35
I/O 36 - I/O 39
I/O 40 - I/O 43
I/O 44 - I/O 47
I/O 48 - I/O 51
I/O 52 - I/O 55
I/O 56 - I/O 59
I/O 60 - I/O 63
26,
30,
34,
38,
45,
49,
53,
57,
68,
72,
76,
80,
3,
7,
11,
15,
27,
31,
35,
39,
46,
50,
54,
58,
69,
73,
77,
81,
4,
8,
12,
16,
28,
32,
36,
40,
47,
51,
55,
59,
70,
74,
78,
82,
5,
9,
13,
17,
29,
33,
37,
41,
48,
52,
56,
60,
71,
75,
79,
83,
6,
10,
14,
18
Input/Output Pins - These are the general purpose I/O pins used by the
logic array.
IN 4 - IN 7
67,
84,
2,
19
Dedicated input pins to the device.
ispEN*/NC
23
SDI*/IN 0
25
MODE*/IN 1
42
SDO*/IN 2
44
SCLK*/IN 3
61
RESET
24
Y0
20
Y1
66
Y2
63
Y3
62
GND
VCC
1,
21,
Input – Dedicated in-system programming enable input pin. This pin
is brought low to enable the programming mode. The MODE, SDI,
SDO and SCLK options become active.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as an input
pin to load programming data into the device. SDI/IN 0 also is used as
one of the two control pins for the isp state machine.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as a pin to
control the operation of the isp state machine.
Input/Output – This pin performs two functions. It is a dedicated input
pin when ispEN is logic high. When ispEN is logic low, it functions as
an output pin to read serial shift register data.
Input – This pin performs two functions. It is a dedicated input when
ispEN is logic high. When ispEN is logic low, it functions as a clock pin
for the Serial Shift Register.
Active Low (0) Reset pin which resets all of the GLB and I/O registers
in the device.
Dedicated Clock input. This clock input is connected to one of the
clock inputs of all of the GLBs on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB on the
device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB and/or
any I/O cell on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any I/O cell on the
device.
22,
65
43,
64
Ground (GND)
VCC
Table 2-0002A-32-isp
* For ispLSI 1032 Only
12
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Description
Name
Description
TQFP Pin Numbers
I/O 0 - I/O 3
I/O 4 - I/O 7
I/O 8 - I/O 11
I/O 12 - I/O 15
I/O 16 - I/O 19
I/O 20 - I/O 23
I/O 24 - I/O 27
I/O 28 - I/O 31
I/O 32 - I/O 35
I/O 36 - I/O 39
I/O 40 - I/O 43
I/O 44 - I/O 47
I/O 48 - I/O 51
I/O 52 - I/O 55
I/O 56 - I/O 59
I/O 60 - I/O 63
IN 4 - IN 7
17,
21,
29,
33,
40,
44,
48,
56,
67,
71,
79,
83,
90,
94,
98,
6,
66,
ispEN*/NC
14
SDI*/IN 0
16
MODE*/IN 1
37
SDO*/IN 2
39
SCLK*/IN 3
60
NC
1,
26,
51,
76,
RESET
15
Y0
11
Y1
65
Y2
62
Y3
61
GND
VCC
13,
12,
18,
22,
30,
34,
41,
45,
53,
57,
68,
72,
80,
84,
91,
95,
3,
7,
87,
2,
27,
52,
77,
38,
64
19,
23,
31,
35,
42,
46,
54,
58,
69,
73,
81,
85,
92,
96,
4,
8,
89,
24,
49,
74,
99,
63,
20,
28,
32,
36,
43,
47,
55,
59,
70,
78,
82,
86,
93,
97,
5,
9
10
25,
50,
75
100
88
Input/Output Pins - These are the general purpose I/O pins used by the
logic array.
Dedicated input pins to the device.
Input – Dedicated in-system programming enable input pin. This pin
is brought low to enable the programming mode. The MODE, SDI,
SDO and SCLK options become active.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as an input
pin to load programming data into the device. SDI/IN 0 also is used as
one of the two control pins for the isp state machine.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as a pin to
control the operation of the isp state machine.
Input/Output – This pin performs two functions. It is a dedicated input
pin when ispEN is logic high. When ispEN is logic low, it functions as
an output pin to read serial shift register data.
Input – This pin performs two functions. It is a dedicated input when
ispEN is logic high. When ispEN is logic low, it functions as a clock pin
for the Serial Shift Register.
These pins are not used.
Active Low (0) Reset pin which resets all of the GLB and I/O registers
in the device.
Dedicated Clock input. This clock input is connected to one of the
clock inputs of all of the GLBs on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB on the
device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB and/or
any I/O cell on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any I/O cell on the
device.
Ground (GND)
VCC
Table 2- 0002B-32-isp
* For ispLSI 1032 Only
13
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Description
Name
CPGA Pin Numbers
I/O 0 - I/O 3
I/O 4 - I/O 7
I/O 8 - I/O 11
I/O 12 - I/O 15
I/O 16 - I/O 19
I/O 20 - I/O 23
I/O 24 - I/O 27
I/O 28 - I/O 31
I/O 32 - I/O 35
I/O 36 - I/O 39
I/O 40 - I/O 43
I/O 44 - I/O 47
I/O 48 - I/O 51
I/O 52 - I/O 55
I/O 56 - I/O 59
I/O 60 - I/O 63
F1,
K1,
K3,
L4,
L7,
K8,
L11,
J11,
E9,
B11,
B9,
A8,
A5,
B4,
A1,
C1,
H1,
J2,
L2,
J5,
K7,
L9,
K10,
H10,
D11,
C10,
A10,
B6,
B5,
A3,
B2,
D2,
IN 4 - IN 7
E10, C7,
ispEN*/NC
G3
SDI*/IN 0
G2
MODE*/IN 1
K6
SDO*/IN 2
J7
SCLK*/IN 3
G10
RESET
G1
Y0
E1
Y1
E11
Y2
G9
Y3
G11
NC
G3
GND
VCC
C6,
F2,
Description
H2,
L1,
L3,
K5,
L6,
L10,
J10,
H11,
D10,
A11,
A9,
B7,
C5,
A2,
C2,
D1,
J1,
K2,
K4,
L5,
L8,
K9,
K11,
F10,
C11,
B10,
B8,
A7,
A4,
B3,
B1,
E3
Input/Output Pins - These are the general purpose I/O pins used by the
logic array.
A6,
E2
Dedicated input pins to the device.
Input – Dedicated in-system programming enable input pin. This pin
is brought low to enable the programming mode. The MODE, SDI,
SDO and SCLK options become active.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as an input
pin to load programming data into the device. SDI/IN 0 also is used as
one of the two control pins for the isp state machine.
Input – This pin performs two functions. It is a dedicated input pin when
ispEN is logic high. When ispEN is logic low, it functions as a pin to
control the operation of the isp state machine.
Input/Output – This pin performs two functions. It is a dedicated input
pin when ispEN is logic high. When ispEN is logic low, it functions as
an output pin to read serial shift register data.
Input – This pin performs two functions. It is a dedicated input when
ispEN is logic high. When ispEN is logic low, it functions as a clock pin
for the Serial Shift Register.
Active Low (0) Reset pin which resets all of the GLB and I/O registers
in the device.
Dedicated Clock input. This clock input is connected to one of the
clock inputs of all of the GLBs on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB on the
device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any GLB and/or
any I/O cell on the device.
Dedicated Clock input. This clock input is brought into the clock
distribution network, and can optionally be routed to any I/O cell on the
device.
This pin should be left floating or tied to VCC.
This pin should never be tied to GND.
F3,
F11
F9,
J6
Ground (GND)
VCC
Table 2-0002-32/883
14
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Configuration
I/O 41
I/O 40
I/O 39
I/O 42
I/O 43
I/O 45
I/O 44
I/O 46
IN 5
I/O 47
I/O 48
IN 6
GND
I/O 49
I/O 51
I/O 50
I/O 52
I/O 53
I/O 55
I/O 54
I/O 56
ispLSI and pLSI 1032 84-Pin PLCC Pinout Diagram
11 10 9 8 7 6 5 4 3 2 1 84 83 82 81 80 79 78 77 76 75
I/O 57
12
74
I/O 38
I/O 58
I/O 59
13
73
14
72
I/O 37
I/O 36
I/O 60
15
71
I/O 35
I/O 61
16
70
I/O 34
I/O 62
I/O 63
17
69
18
68
I/O 33
I/O 32
IN 7
19
67
IN 4
Y0
VCC
GND
20
66
Y1
VCC
GND
*ispEN/NC
RESET
23
24
62
Y2
Y3
*SDI/IN 0
25
61
IN 3/SCLK*
I/O 0
I/O 1
26
60
27
59
I/O 31
I/O 30
I/O 2
28
58
I/O 29
I/O 3
29
57
I/O 28
I/O 4
I/O 5
I/O 6
30
56
31
55
32
54
I/O 27
I/O 26
I/O 25
ispLSI 1032
pLSI 1032
21
22
65
64
Top View
63
I/O 22
I/O 23
I/O 24
I/O 21
I/O 20
I/O 18
I/O 19
I/O 17
*SDO/IN 2
I/O 16
I/O 15
*MODE/IN 1
GND
I/O 14
I/O 13
I/O 12
I/O 11
I/O 10
I/O 8
I/O 9
I/O 7
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53
*Pins have dual function capability for ispLSI 1032 only (except pin 23, which is ispEN only).
0123-32-isp
15
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Configuration
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ispLSI 1032
pLSI 1032
Top View
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
NC
I/O 38
I/O 37
I/O 36
I/O 35
I/O 34
I/O 33
I/O 32
IN 4
Y1
VCC
GND
Y2
Y3
IN 3/SCLK*
I/O 31
I/O 30
I/O 29
I/O 28
I/O 27
I/O 26
I/O 25
NC
NC
NC
NC
I/O 7
I/O 8
I/O 9
I/O 10
I/O 11
I/O 12
I/O 13
I/O 14
I/O 15
*MODE/IN1
GND
*SDO/IN 2
I/O 16
I/O 17
I/O 18
I/O 19
I/O 20
I/O 21
I/O 22
I/O 23
I/O 24
NC
NC
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
NC
I/O 57
I/O 58
I/O 59
I/O 60
I/O 61
I/O 62
I/O 63
IN 7
Y0
VCC
GND
*ispEN/NC
RESET
*SDI/IN 0
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
NC
NC
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
NC
NC
I/O 56
I/O 55
I/O 54
I/O 53
I/O 52
I/O 51
I/O 50
I/O 49
I/O 48
IN 6
GND
IN 5
I/O 47
I/O 46
I/O 45
I/O 44
I/O 43
I/O 42
I/O 41
I/O 40
I/O 39
NC
NC
ispLSI and pLSI 1032 100-pin TQFP Pinout Diagram
*Pins have dual function capability for ispLSI 1032 only (except pin 14, which is ispEN only).
0766A-32-isp
16
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Pin Configuration
ispLSI and pLSI 1032/883 84-Pin CPGA Pinout Diagram
PIN A1
11
10
9
8
7
6
5
4
3
2
1
I/O38
I/O41
I/O42
I/O44
I/O47
IN6
I/O48
I/O51
I/O53
I/O54
I/O56
A
I/O36
I/O39
I/O40
I/O43
I/O46
I/O45
I/O49
I/O52
I/O55
I/O57
I/O59
B
I/O35
I/O37
IN5
GND
I/O50
INDEX
I/O58
I/O60
C
I/O33
I/O34
I/O61
I/O62
D
Y1
IN4
I/O32
I/O63
IN7
Y0
E
Vcc
I/O31
GND
GND
Vcc
I/O0
F
*ispEN
/NC
*SDI/
IN0
RESET
G
I/O2
I/O1
H
I/O5
I/O3
J
ispLSI 1032/883
pLSI 1032/883
Bottom View
Y3
*SCLK/
IN3
I/O30
I/O29
I/O28
I/O26
I/O27
I/O25
I/O23
I/O24
I/O22
I/O21
Y2
*SDO/
IN2
GND
I/O13
I/O20
I/O17
*MODE/
IN1
I/O14
I/O11
I/O8
I/O7
I/O4
K
I/O19
I/O16
I/O18
I/O15
I/O12
I/O10
I/O9
I/O6
L
*Pins have dual function capability for ispLSI 1032/883 only (except pin G3, which is ispEN only).
0488A-32-isp/883
17
1996 ISP Encyclopedia
Specifications ispLSI and pLSI 1032
Part Number Description
1032 – XX
(is)pLSI
X
X
X
Device Family
Device Number
Grade
Blank = Commercial
I = Industrial
/883 = 883 Military Process
Speed
90 = 90 MHz fmax
80 = 80 MHz fmax
60 = 60 MHz fmax
Package
J = PLCC
T = TQFP
G = CPGA
Power
L = Low
0212-80B-isp1032
ispLSI and pLSI 1032 Ordering Information
COMMERCIAL
Family
ispLSI
fmax (MHz) tpd (ns)
Ordering Number
Package
90
12
ispLSI 1032-90LJ
84-Pin PLCC
90
12
ispLSI 1032-90LT
100-Pin TQFP
80
15
ispLSI 1032-80LJ
84-Pin PLCC
80
15
ispLSI 1032-80LT
100-Pin TQFP
60
20
ispLSI 1032-60LJ
84-Pin PLCC
60
20
ispLSI 1032-60LT
100-Pin TQFP
90
12
pLSI 1032-90LJ
84-Pin PLCC
90
12
pLSI 1032-90LT
100-Pin TQFP
80
15
pLSI 1032-80LJ
84-Pin PLCC
80
15
pLSI 1032-80LT
100-Pin TQFP
60
20
pLSI 1032-60LJ
84-Pin PLCC
60
20
pLSI 1032-60LT
100-Pin TQFP
pLSI
INDUSTRIAL
Family
fmax (MHz) tpd (ns)
Package
60
20
ispLSI 1032-60LJI
84-Pin PLCC
60
20
ispLSI 1032-60LTI
100-Pin TQFP
60
20
pLSI 1032-60LJI
84-Pin PLCC
ispLSI
pLSI
Ordering Number
MILITARY/883
Family
fmax (MHz) tpd (ns)
Ordering Number
SMD Number
Package
ispLSI
60
20
ispLSI 1032-60LG/883
5962-9308501MXC
84-Pin CPGA
pLSI
60
20
pLSI 1032-60LG/883
5962-9466801MXC
84-Pin CPGA
Note: Lattice Semiconductor recognizes the trend in military device procurement towards
using SMD compliant devices, as such, ordering by this number is recommended.
18
Table 2- 0041A-32-isp
1996 ISP Encyclopedia
Copyright © 1997 Lattice Semiconductor Corporation.
E2CMOS, GAL, ispGAL, ispLSI, pLSI, pDS, Silicon Forest, UltraMOS, Lattice Semiconductor, L (stylized) Lattice
Semiconductor Corp., L (stylized) and Lattice (design) are registered trademarks of Lattice Semiconductor Corporation.
Generic Array Logic, ISP, ispATE, ispCODE, ispDOWNLOAD, ispGDS, ispDS, ispDS+, ispStarter, ispSTREAM, ispTEST,
ispTURBO, Latch-Lock, pDS+, RFT, Total ISP and Twin GLB are trademarks of Lattice Semiconductor Corporation. ISP is a
service mark of Lattice Semiconductor Corporation. All brand names or product names mentioned are trademarks or
registered trademarks of their respective holders.
Lattice Semiconductor Corporation (LSC) products are made under one or more of the following U.S. and international
patents: 4,761,768 US, 4,766,569 US, 4,833,646 US, 4,852,044 US, 4,855,954 US, 4,879,688 US, 4,887,239 US, 4,896,296
US, 5,130,574 US, 5,138,198 US, 5,162,679 US, 5,191,243 US, 5,204,556 US, 5,231,315 US, 5,231,316 US, 5,237,218 US,
5,245,226 US, 5,251,169 US, 5,272,666 US, 5,281,906 US, 5,295,095 US, 5,329,179 US, 5,331,590 US, 5,336,951 US,
5,353,246 US, 5,357,156 US, 5,359,573 US, 5,394,033 US, 5,394,037 US, 5,404,055 US, 5,418,390 US, 5,493,205 US,
0194091 EP, 0196771B1 EP, 0267271 EP, 0196771 UK, 0194091 GB, 0196771 WG, P3686070.0-08 WG. LSC does not
represent that products described herein are free from patent infringement or from any third-party right.
The specifications and information herein are subject to change without notice. Lattice Semiconductor Corporation (LSC)
reserves the right to discontinue any product or service without notice and assumes no obligation to correct any errors
contained herein or to advise any user of this document of any correction if such be made. LSC recommends its customers
obtain the latest version of the relevant information to establish, before ordering, that the information being relied upon is
current.
LSC warrants performance of its products to current and applicable specifications in accordance with LSC’s standard
warranty. Testing and other quality control procedures are performed to the extent LSC deems necessary. Specific testing of
all parameters of each product is not necessarily performed, unless mandated by government requirements.
LSC assumes no liability for applications assistance, customer’s product design, software performance, or infringements of
patents or services arising from the use of the products and services described herein.
LSC products are not authorized for use in life-support applications, devices or systems. Inclusion of LSC products in such
applications is prohibited.
LATTICE SEMICONDUCTOR CORPORATION
5555 Northeast Moore Court
Hillsboro, Oregon 97124 U.S.A.
Tel.: (503) 681-0118
FAX: (503) 681-3037
http://www.latticesemi.com
February 1997