FREESCALE MMG3003NT1_08

Freescale Semiconductor
Technical Data
NOT RECOMMENDED FOR NEW DESIGN
Heterojunction Bipolar Transistor
Technology (InGaP HBT)
MMG3003NT1
Broadband High Linearity Amplifier
The MMG3003NT1 is a General Purpose Amplifier that is internally
input matched and internally output prematched. It is designed for a broad
range of Class A, small - signal, high linearity, general purpose applications. It is suitable for applications with frequencies from 40 to 3600 MHz
such as Cellular, PCS, BWA, WLL, PHS, CATV, VHF, UHF, UMTS and
general small - signal RF.
40 - 3600 MHz, 20 dB
24 dBm
InGaP HBT
Features
• Frequency: 40 - 3600 MHz
• P1dB: 24 dBm @ 900 MHz
• Small - Signal Gain: 20 dB @ 900 MHz
• Third Order Output Intercept Point: 40.5 dBm @ 900 MHz
• Single Voltage Supply
• Internally Matched to 50 Ohms
• Low Cost SOT - 89 Surface Mount Package
• RoHS Compliant
• In Tape and Reel. T1 Suffix = 1000 Units per 12 mm, 7 inch Reel.
Table 1. Typical Performance (1)
3
CASE 1514 - 02, STYLE 1
SOT - 89
PLASTIC
Table 2. Maximum Ratings
Characteristic
Symbol
900
MHz
2140
MHz
3500
MHz
Unit
Small - Signal Gain
(S21)
Gp
20
16.9
12
dB
Input Return Loss
(S11)
IRL
- 15
- 14.1
- 11.2
dB
Output Return Loss
(S22)
ORL
- 9.3
−14.5
- 10.2
dB
Power Output @1dB
Compression
P1db
24
23.3
20.5
dBm
IP3
40.5
40
37
dBm
Third Order Output
Intercept Point
12
Rating
Symbol
Value
Unit
Supply Voltage
VCC
7
V
Supply Current
ICC
400
mA
RF Input Power
Pin
15
dBm
Storage Temperature Range
Tstg
- 65 to +150
°C
Junction Temperature (2)
TJ
150
°C
2. For reliable operation, the junction temperature should not
exceed 150°C.
1. VCC = 6.2 Vdc, TC = 25°C, 50 ohm system
Table 3. Thermal Characteristics (VCC = 6.2 Vdc, ICC = 180 mA, TC = 25°C)
Characteristic
Thermal Resistance, Junction to Case
Symbol
Value (3)
Unit
RθJC
31.6
°C/W
NOT RECOMMENDED FOR NEW DESIGN
Document Number: MMG3003NT1
Rev. 7, 3/2008
3. Refer to AN1955, Thermal Measurement Methodology of RF Power Amplifiers. Go to http://www.freescale.com/rf.
Select Documentation/Application Notes - AN1955.
© Freescale Semiconductor, Inc., 2004-2008. All rights reserved.
RF Device Data
Freescale Semiconductor
MMG3003NT1
1
Characteristic
NOT RECOMMENDED FOR NEW DESIGN
Symbol
Min
Typ
Max
Unit
Small - Signal Gain (S21)
Gp
19.3
20
—
dB
Input Return Loss (S11)
IRL
—
- 15
—
dB
Output Return Loss (S22)
ORL
—
- 9.3
—
dB
Power Output @ 1dB Compression
P1dB
—
24
—
dBm
Third Order Output Intercept Point
IP3
—
40.5
—
dBm
Noise Figure
NF
—
4
—
dB
Supply Current (1)
ICC
160
180
205
mA
Supply Voltage (1)
VCC
—
6.2
—
V
1. For reliable operation, the junction temperature should not exceed 150°C.
NOT RECOMMENDED FOR NEW DESIGN
Table 4. Electrical Characteristics (VCC = 6.2 Vdc, 900 MHz, TC = 25°C, 50 ohm system, in Freescale Application Circuit)
MMG3003NT1
2
RF Device Data
Freescale Semiconductor
Table 5. Functional Pin Description
2
Pin Function
1
RFin
2
Ground
3
RFout/DC Supply
1
2
3
Figure 1. Functional Diagram
Table 6. ESD Protection Characteristics
Test Conditions/Test Methodology
Class
Human Body Model (per JESD 22 - A114)
1B (Minimum)
Machine Model (per EIA/JESD 22 - A115)
A (Minimum)
Charge Device Model (per JESD 22 - C101)
IV (Minimum)
Table 7. Moisture Sensitivity Level
Test Methodology
Per JESD 22 - A113, IPC/JEDEC J - STD - 020
Rating
Package Peak Temperature
Unit
1
260
°C
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
Pin
Number
MMG3003NT1
RF Device Data
Freescale Semiconductor
3
50 OHM TYPICAL CHARACTERISTICS
25
0
−10
15
−20
S11
VCC = 6.2 Vdc
ICC = 180 mA
10
−30
0
1
2
3
4
2
3
4
f, FREQUENCY (GHz)
Figure 2. Small - Signal Gain (S21) versus
Frequency
Figure 3. Input/Output Return Loss versus
Frequency
23
900 MHz, C5 = 2.7 pF
19
1960 MHz, C5, C6 = 1.3 pF
17
2140 MHz, C5, C6 = 1.3 pF
15
2600 MHz, C5 = 1.2 pF
13
3500 MHz, C5 = 0.5 pF
11
VCC = 6.2 Vdc
ICC = 180 mA
9
5
10
15
20
P1dB, 1 dB COMPRESSION POINT (dBm)
25
21
24
23
22
21
20
19
VCC =6.2 Vdc
ICC = 180 mA
18
17
0.5
25
1
1.5
2
2.5
3
Pout, OUTPUT POWER (dBm)
f, FREQUENCY (GHz)
Figure 4. Small - Signal Gain versus Output
Power
Figure 5. P1dB versus Frequency
200
150
100
50
0
4
4.5
5
5.5
6
VCC, COLLECTOR VOLTAGE (V)
Figure 6. Collector Current versus Collector
Voltage
6.5
IP3, THIRD ORDER OUTPUT INTERCEPT POINT (dBm)
Gp, SMALL−SIGNAL GAIN (dB)
1
0
f, FREQUENCY (GHz)
3.5
45
42
39
36
VCC = 6.2 Vdc
ICC = 180 mA
100 kHz Tone Spacing
33
30
0
1
2
3
NOT RECOMMENDED FOR NEW DESIGN
−40°C
20
S11, S22(dB)
Gp, SMALL−SIGNAL GAIN (dB)
S22
25°C
VCC = 6.2 Vdc
ICC, COLLECTOR CURRENT (mA)
NOT RECOMMENDED FOR NEW DESIGN
TC = 85°C
4
f, FREQUENCY (GHz)
Figure 7. Third Order Output Intercept Point
versus Frequency
MMG3003NT1
4
RF Device Data
Freescale Semiconductor
42
39
36
33
f = 900 MHz
100 kHz Tone Spacing
30
6
5.8
6.2
6.4
6.6
VCC, COLLECTOR VOLTAGE (V)
42
41
40
39
−40
−20
0
20
40
60
80
100
T, TEMPERATURE (_C)
Figure 9. Third Order Output Intercept Point
versus Case Temperature
Figure 8. Third Order Output Intercept Point
versus Collector Voltage
105
−30
MTTF (YEARS)
−40
−50
−60
−70
103
−80
9
12
15
18
21
24
120
125
130
135
140
145
150
Pout, OUTPUT POWER (dBm)
TJ, JUNCTION TEMPERATURE (°C)
Figure 10. Third Order Intermodulation versus
Output Power
Figure 11. MTTF versus Junction Temperature
8
6
4
2
VCC = 6.2 Vdc
ICC = 180 mA
0
0
104
VCC = 6.2 Vdc
ICC = 180 mA
f = 900 MHz
100 kHz Tone Spacing
0.5
1
1.5
2
2.5
3
3.5
NOTE: The MTTF is calculated with VCC = 6.2 Vdc, ICC = 180 mA
ACPR, ADJACENT CHANNEL POWER RATIO (dBc)
IMD, THIRD ORDER
INTERMODULATION DISTORTION (dBc)
VCC = 6.2 Vdc
f = 900 MHz
100 kHz Tone Spacing
8 Vdc Supply with 10 W Dropping Resistor
4
−20
VCC = 6.2 Vdc, ICC = 180 mA, f = 2140 MHz, C5 = 1.3 pF
Single−Carrier W−CDMA, 3.84 MHz Channel Bandwidth
Input Signal PAR = 8.5 dB @ 0.01% Probability (CCDF)
−30
−40
−50
−60
NOT RECOMMENDED FOR NEW DESIGN
IP3, THIRD ORDER OUTPUT INTERCEPT POINT (dBm)
IP3, THIRD ORDER OUTPUT INTERCEPT POINT (dBm)
45
NF, NOISE FIGURE (dB)
NOT RECOMMENDED FOR NEW DESIGN
50 OHM TYPICAL CHARACTERISTICS
−70
9
11
13
15
17
f, FREQUENCY (GHz)
Pout, OUTPUT POWER (dBm)
Figure 12. Noise Figure versus Frequency
Figure 13. Single - Carrier W - CDMA Adjacent
Channel Power Ratio versus Output Power
19
MMG3003NT1
RF Device Data
Freescale Semiconductor
5
50 OHM APPLICATION CIRCUIT: 40- 800 MHz
VSUPPLY
C4
L1
RF
INPUT
Z1
DUT
Z2
C1
Z1
Z2
Z3
Z4
0.347″
0.575″
0.172″
0.403″
Z3
Z4
Z6
C2
VCC
x 0.058″ Microstrip
x 0.058″ Microstrip
x 0.058″ Microstrip
x 0.058″ Microstrip
Z5
Z5
Z6
PCB
RF
OUTPUT
C5
0.286″ x 0.058″ Microstrip
0.061″ x 0.058″ Microstrip
Getek Grade ML200C, 0.031″, εr = 4.1
Figure 14. 50 Ohm Test Circuit Schematic
30
S21
20
R1
C4
C3
10
L1
0
C2
C1
S22
−10
C5
−20
VCC = 6.2 Vdc
ICC = 180 mA
S11
−30
200
0
400
600
MMG30XX
Rev 2
800
f, FREQUENCY (MHz)
Figure 15. S21, S11 and S22 versus Frequency
Figure 16. 50 Ohm Test Circuit Component Layout
Table 8. 50 Ohm Test Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C2, C4
0.01 μF Chip Capacitors
C0603C103J5RAC
Kemet
C3
68 pF Chip Capacitor
C0805C680J5RAC
Kemet
C5 (1)
2.7 pF Chip Capacitor
12105J2R7BS
AVX
L1
470 nH Chip Inductor
BK2125HM471 - T
Taiyo Yuden
R1
7.5 W Chip Resistor
RK73B2ATTE7R5J
KOA Speer
1. Tuning capacitor: Capacitor value and location on the transmission line are varied for different frequencies.
Table 9. Supply Voltage versus R1 Values
Supply Voltage
7
8
9
10
11
12
V
R1 Value
4.4
10
15.6
21
27
32
Ω
NOT RECOMMENDED FOR NEW DESIGN
C3
S21, S11, S22 (dB)
NOT RECOMMENDED FOR NEW DESIGN
R1
Note: To provide VCC = 6.2 Vdc and ICC = 180 mA at the device.
MMG3003NT1
6
RF Device Data
Freescale Semiconductor
50 OHM APPLICATION CIRCUIT: 800 - 1100 MHz
VSUPPLY
C4
L1
RF
INPUT
Z1
DUT
Z2
C1
Z1, Z6
Z2
Z3
Z3
Z4
0.347″ x 0.058″ Microstrip
0.575″ x 0.058″ Microstrip
0.172″ x 0.058″ Microstrip
Z4
Z5
PCB
Z6
Z5
C5
VCC
RF
OUTPUT
C2
0.333″ x 0.058″ Microstrip
0.07″ x 0.058″ Microstrip
Getek Grade ML200C, 0.031″, εr = 4.1
Figure 17. 50 Ohm Test Circuit Schematic
30
S21
20
R1
10
C4
C3
0
L1
S22
−10
C2
C1
C5
−20
S11
−30
VCC = 6.2 Vdc
ICC = 180 mA
−40
600
700
800
900
1000
1100
MMG30XX
Rev 2
1200
f, FREQUENCY (MHz)
Figure 18. S21, S11 and S22 versus Frequency
Figure 19. 50 Ohm Test Circuit Component Layout
Table 10. 50 Ohm Test Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C2
47 pF Chip Capacitors
C0805C470J5RAC
Kemet
C3
68 pF Chip Capacitor
C0805C680J5RAC
Kemet
C4
0.01 μF Chip Capacitor
C0603C103J5RAC
Kemet
C5 (1)
2.7 pF Chip Capacitor
06035J2R7BS
AVX
L1
22 nH Chip Inductor
HK160822NJ - T
Taiyo Yuden
R1
7.5 W Chip Resistor
RK73B2ATTE7R5J
KOA Speer
1. Tuning capacitor: Capacitor value and location on the transmission line are varied for different frequencies.
NOT RECOMMENDED FOR NEW DESIGN
C3
S21, S11, S22 (dB)
NOT RECOMMENDED FOR NEW DESIGN
R1
MMG3003NT1
RF Device Data
Freescale Semiconductor
7
50 OHM APPLICATION CIRCUIT: 1800- 2400 MHz
VSUPPLY
C4
L1
RF
INPUT
Z1
DUT
Z2
C1
Z3
Z4
Z1, Z7
Z2
Z3
Z4
0.347″
0.575″
0.172″
0.047″
Z6
Z5
C6
C5
VCC
x 0.058″ Microstrip
x 0.058″ Microstrip
x 0.058″ Microstrip
x 0.058″ Microstrip
Z5
Z6
PCB
RF
OUTPUT
Z7
C2
0.062″ x 0.058″ Microstrip
0.466″ x 0.058″ Microstrip
Getek Grade ML200C, 0.031″, εr = 4.1
Figure 20. 50 Ohm Test Circuit Schematic
30
20
S21
R1
C4
C3
10
0
L1
S11
−10
C2
C1
C5 C6
−20
S22
VCC = 6.2 Vdc
ICC = 180 mA
−30
MMG30XX
Rev 2
−40
1600
1800
2000
2200
2400
2600
f, FREQUENCY (MHz)
Figure 21. S21, S11 and S22 versus Frequency
Figure 22. 50 Ohm Test Circuit Component Layout
Table 11. 50 Ohm Test Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C2
47 pF Chip Capacitors
C0805C470J5RAC
Kemet
C3
68 pF Chip Capacitor
C0805C680J5RAC
Kemet
C4
0.01 μF Chip Capacitor
C0603C103J5RAC
Kemet
C5 (1)
1.2 pF Chip Capacitor
06035J1R2BS
AVX
(1)
C6
0.1 pF Chip Capacitor
06035J0R1BS
AVX
L1
22 nH Chip Inductor
HK160822NJ - T
Taiyo Yuden
R1
7.5 W Chip Resistor
RK73B2ATTE7R5J
KOA Speer
1. Tuning capacitor: Capacitor value and location on the transmission line are varied for different frequencies.
NOT RECOMMENDED FOR NEW DESIGN
C3
S21, S11, S22 (dB)
NOT RECOMMENDED FOR NEW DESIGN
R1
MMG3003NT1
8
RF Device Data
Freescale Semiconductor
50 OHM APPLICATION CIRCUIT: 2500 - 2700 MHz
VSUPPLY
C4
L1
RF
INPUT
Z1
Z2
DUT
C1
Z1, Z6
Z2
Z3
Z3
VCC
0.347″ x 0.058″ Microstrip
0.575″ x 0.058″ Microstrip
0.086″ x 0.058″ Microstrip
Z4
Z5
C5
RF
OUTPUT
Z6
C2
Z4
Z5
PCB
0.085″ x 0.058″ Microstrip
0.404″ x 0.058″ Microstrip
Getek Grade ML200C, 0.031″, εr = 4.1
Figure 23. 50 Ohm Test Circuit Schematic
30
S21
20
R1
10
C4
C3
0
L1
S22
−10
C2
C1
C5
−20
S11
VCC = 6.2 Vdc
ICC = 180 mA
−30
−40
2200
2300
2400
2500
2600
2700
MMG30XX
Rev 2
2800
f, FREQUENCY (MHz)
Figure 24. S21, S11 and S22 versus Frequency
Figure 25. 50 Ohm Test Circuit Component Layout
Table 12. 50 Ohm Test Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C2
2.2 pF Chip Capacitors
06035J2R2BS
AVX
C3
68 pF Chip Capacitor
C0805C680J5RAC
Kemet
C4
0.01 μF Chip Capacitor
C0603C103J5RAC
Kemet
C5 (1)
1.2 pF Chip Capacitor
06035J1R2BS
AVX
L1
39 nH Chip Inductor
HK160839NJ - T
Taiyo Yuden
R1
7.5 W Chip Resistor
RK73B2ATTE7R5J
KOA Speer
1. Tuning capacitor: Capacitor value and location on the transmission line are varied for different frequencies.
NOT RECOMMENDED FOR NEW DESIGN
C3
S21, S11, S22 (dB)
NOT RECOMMENDED FOR NEW DESIGN
R1
MMG3003NT1
RF Device Data
Freescale Semiconductor
9
50 OHM APPLICATION CIRCUIT: 3400 - 3600 MHz
VSUPPLY
C4
L1
RF
INPUT
Z1
DUT
Z2
C1
Z1, Z6
Z2
Z3
Z3
VCC
0.347″ x 0.058″ Microstrip
0.575″ x 0.058″ Microstrip
0.086″ x 0.058″ Microstrip
Z4
RF
OUTPUT
Z6
Z5
C5
C2
Z4
Z5
PCB
0.085″ x 0.058″ Microstrip
0.404″ x 0.058″ Microstrip
Getek Grade ML200C, 0.031″, εr = 4.1
Figure 26. 50 OhmTest Circuit Schematic
20
15
S21
R1
10
C4
C3
5
L1
0
C2
C1
−5
C5
S22
−10
S11
VCC = 6.2 Vdc
ICC = 180 mA
−15
−20
3200
3300
3400
3500
3600
3700
MMG30XX
Rev 2
3800
f, FREQUENCY (MHz)
Figure 27. S21, S11 and S22 versus Frequency
Figure 28. 50 Ohm Test Circuit Component Layout
Table 13. 50 OhmTest Circuit Component Designations and Values
Part
Description
Part Number
Manufacturer
C1, C2
2.2 pF Chip Capacitors
06035J2R2BS
AVX
C3
68 pF Chip Capacitor
C0805C680J5RAC
Kemet
C4
0.01 μF Chip Capacitor
C0603C103J5RAC
Kemet
C5 (1)
0.5 pF Chip Capacitor
06035J0R5BS
AVX
L1
39 nH Chip Inductor
HK160839NJ - T
Taiyo Yuden
R1
7.5 W Chip Resistor
RK73B2ATTE7R5J
KOA Speer
1. Tuning capacitor: Capacitor value and location on the transmission line are varied for different frequencies.
NOT RECOMMENDED FOR NEW DESIGN
C3
S21, S11, S22 (dB)
NOT RECOMMENDED FOR NEW DESIGN
R1
MMG3003NT1
10
RF Device Data
Freescale Semiconductor
50 OHM TYPICAL CHARACTERISTICS
S11
S21
S12
S22
f
MHz
|S11|
∠φ
|S21|
∠φ
|S12|
∠φ
|S22|
∠φ
0100
0.141
178.297
12.985
173.850 0
0.057
0.785 0
0.087
- 167.704
0150
0.153
175.556
12.654
168.9
0.057
- 0.913
0.136
- 137.479
0200
0.155
160.177
13.067
164.046
0.059
- 2.423
0.125
- 131.397
0250
0.152
159.068
12.851
160.334
0.058
- 2.897
0.159
- 130.233
0300
0.147
156.309
12.685
156.518
0.058
- 3.227
0.187
- 128.649
0350
0.139
153.853
12.519
152.664
0.058
- 3.971
0.212
- 128.651
0400
0.135
150.838
12.327
149.087
0.057
- 4.471
0.239
- 129.263
0450
0.129
148.378
12.124
145.521
0.057
- 4.799
0.263
- 130.237
0500
0.123
145.160
11.915
142.009
0.057
- 5.285
0.285
- 131.637
0550
0.117
142.332
11.694
138.634
0.057
- 5.623
0.306
- 133.294
0600
0.112
139.364
11.470
135.366
0.057
- 6.012
0.326
- 135.284
0650
0.106
136.769
11.238
132.093
0.057
- 6.295
0.345
- 137.146
0700
0.101
133.592
11.004
128.948
0.057
- 6.705
0.362
- 139.07
0750
0.096
131.187
10.770
125.882
0.057
- 7.044
0.378
- 141.171
0800
0.090
128.979
10.532
122.88
0.056
- 7.277
0.394
- 143.273
0850
0.086
126.711
10.298
119.942
0.056
- 7.495
0.408
- 145.372
0900
0.081
124.541
10.066
117.117
0.056
- 7.847
0.422
- 147.618
0950
0.076
122.189
9.841
114.276
0.056
- 8.05
0.435
- 149.849
1000
0.073
121.191
9.611
111.625
0.056
- 8.311
0.447
- 151.947
1050
0.069
119.451
9.393
108.992
0.056
- 8.582
0.458
- 154.142
1100
0.065
118.827
9.170
106.412
0.056
- 8.89
0.470
- 156.289
1150
0.062
118.851
8.957
103.879
0.056
- 9.079
0.480
- 158.481
1200
0.059
118.882
8.742
101.417
0.056
- 9.405
0.490
- 160.544
1250
0.056
119.703
8.541
99.039
0.056
- 9.615
0.498
- 162.608
1300
0.054
120.919
8.340
96.664
0.056
- 9.805
0.507
- 164.561
1350
0.051
123.223
8.143
94.364
0.056
- 10.198
0.515
- 166.501
1400
0.048
125.019
7.957
92.107
0.056
- 10.536
0.522
- 168.351
1450
0.046
128.063
7.774
89.892
0.056
- 10.724
0.530
- 170.229
1500
0.033
135.869
7.640
87.599
0.057
- 11.197
0.529
- 172.918
1550
0.030
139.127
7.475
85.482
0.057
- 11.434
0.536
- 174.487
1600
0.027
142.585
7.322
83.442
0.057
- 11.649
0.541
- 175.93
1650
0.024
146.640
7.170
81.444
0.057
- 11.993
0.546
- 177.394
1700
0.023
152.580
7.040
79.397
0.058
- 12.335
0.552
- 179.018
1750
0.021
158.266
6.890
77.439
0.058
- 12.616
0.555
179.899
1800
0.021
166.196
6.756
75.477
0.058
- 12.879
0.560
178.582
1850
0.022
171.633
6.621
73.576
0.058
- 13.16
0.563
177.318
1900
0.023
177.431
6.495
71.695
0.058
- 13.445
0.566
176.139
1950
0.025
- 176.142
6.371
69.952
0.059
- 13.806
0.570
175.08
2000
0.027
- 173.137
6.251
67.988
0.059
- 14.176
0.573
173.812
2050
0.029
- 170.367
6.135
66.175
0.059
- 14.413
0.577
172.704
2100
0.031
- 168.467
6.025
64.385
0.060
- 14.882
0.580
171.566
2150
0.033
- 168.388
5.921
62.595
0.060
- 15.338
0.583
170.426
2200
0.036
- 169.515
5.815
60.823
0.060
- 15.659
0.586
169.283
2250
0.039
- 170.197
5.716
59.079
0.061
- 16.136
0.589
168.164
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
Table 14. Common Emitter S - Parameters (VCC = 6.2 Vdc, ICC = 180 mA, TC = 25°C, 50 Ohm System)
(continued)
MMG3003NT1
RF Device Data
Freescale Semiconductor
11
50 OHM TYPICAL CHARACTERISTICS
S11
S21
S12
S22
f
MHz
|S11|
∠φ
|S21|
∠φ
|S12|
∠φ
|S22|
∠φ
2300
0.042
- 171.944
5.618
57.331
0.061
- 16.513
0.591
167.003
2350
0.045
- 173.747
5.525
55.573
0.061
- 16.98
0.593
165.803
2400
0.048
- 175.268
5.431
53.848
0.062
- 17.435
0.595
164.669
2450
0.052
- 177.409
5.345
52.136
0.062
- 17.955
0.597
163.447
2500
0.056
- 178.703
5.258
50.405
0.062
- 18.404
0.598
162.182
2550
0.060
179.650
5.173
48.736
0.063
- 19.004
0.600
160.854
2600
0.063
177.705
5.096
47.012
0.063
- 19.505
0.602
159.516
2650
0.067
175.894
5.015
45.266
0.063
- 20.1
0.603
158.1
2700
0.071
174.932
4.938
43.452
0.064
- 20.75
0.605
156.649
2750
0.074
172.453
4.861
41.831
0.064
- 21.297
0.607
155.174
2800
0.079
170.595
4.788
40.113
0.065
- 21.999
0.609
153.675
2850
0.083
168.962
4.715
38.402
0.065
- 22.577
0.610
152.104
2900
0.087
167.373
4.643
36.711
0.065
- 23.239
0.612
150.539
2950
0.091
165.543
4.573
35.036
0.066
- 23.942
0.614
148.941
3000
0.095
164.513
4.506
33.356
0.066
- 24.652
0.616
147.251
3050
0.099
163.309
4.438
31.684
0.066
- 25.269
0.618
145.747
3100
0.103
162.077
4.373
29.98
0.067
- 26.085
0.620
144.105
3150
0.107
161.249
4.308
28.307
0.067
- 26.717
0.622
142.483
3200
0.110
160.222
4.244
26.653
0.067
- 27.483
0.624
140.894
3250
0.114
159.057
4.182
25.007
0.068
- 28.223
0.626
139.31
3300
0.117
158.018
4.121
23.381
0.068
- 29.013
0.629
137.737
3350
0.119
156.94
4.061
21.791
0.068
- 29.779
0.631
136.267
3400
0.122
155.757
4.004
20.196
0.069
- 30.535
0.633
134.76
3450
0.126
154.754
3.949
18.618
0.069
- 31.29
0.635
6
3500
0.12826
153.898
3.895
17.049
0.06938
- 31.957
0.6367
131.951
3550
0.13168
152.875
3.84045
15.491
0.06971
- 32.814
0.6392
130.655
3600
0.13497
152.157
3.78882
13.97
0.07016
- 33.474
0.64031
129.412
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
Table 14. Common Emitter S - Parameters (VCC = 6.2 Vdc, ICC = 180 mA, TC = 25°C, 50 Ohm System) (continued)
MMG3003NT1
12
RF Device Data
Freescale Semiconductor
1.7
0.305 diameter
2.49
3.48
5.33
1.27
1.27
0.58
0.86
0.64
3.86
Recommended Solder Stencil
NOTES:
1. THERMAL AND RF GROUNDING CONSIDERATIONS SHOULD BE
USED IN PCB LAYOUT DESIGN.
2. DEPENDING ON PCB DESIGN RULES, AS MANY VIAS AS
POSSIBLE SHOULD BE PLACED ON THE LANDING PATTERN.
3. IF VIAS CANNOT BE PLACED ON THE LANDING PATTERN, THEN
AS MANY VIAS AS POSSIBLE SHOULD BE PLACED AS CLOSE TO
THE LANDING PATTERN AS POSSIBLE FOR OPTIMAL THERMAL
AND RF PERFORMANCE.
4. RECOMMENDED VIA PATTERN SHOWN HAS 0.381 x 0.762 MM
PITCH.
Figure 29. Recommended Mounting Configuration
2.54
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
7.62
MMG3003NT1
RF Device Data
Freescale Semiconductor
13
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
PACKAGE DIMENSIONS
MMG3003NT1
14
RF Device Data
Freescale Semiconductor
MMG3003NT1
RF Device Data
Freescale Semiconductor
15
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
MMG3003NT1
16
RF Device Data
Freescale Semiconductor
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
PRODUCT DOCUMENTATION
Refer to the following documents to aid your design process.
REVISION HISTORY
The following table summarizes revisions to this document.
Revision
Date
Description
5
Mar. 2007
•
Corrected and updated Part Numbers in Tables 8, 10, 11, 12, and 13, Component Designations and Values,
to RoHS compliant part numbers, p. 6 - 10
6
July 2007
•
Replaced Case Outline 1514 - 01 with 1514 - 02, Issue D, p. 1, 14 - 16. Case updated to add missing
dimension for Pin 1 and Pin 3.
7
Mar. 2008
• Removed Footnote 2, Continuous voltage and current applied to device, from Table 2, Maximum Ratings,
p. 1
•
Corrected Fig. 13, Single - Carrier W - CDMA Adjacent Channel Power Ratio versus Output Power y - axis
(ACPR) unit of measure to dBc, p. 5
• Corrected S - Parameter table frequency column label to read “MHz” versus “GHz” and corrected
frequency values from GHz to MHz, p. 11, 12
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
Application Notes
• AN1955: Thermal Measurement Methodology of RF Power Amplifiers
• AN3100: General Purpose Amplifier Biasing
MMG3003NT1
RF Device Data
Freescale Semiconductor
17
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1 - 800 - 521 - 6274 or +1 - 480 - 768 - 2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1 - 8 - 1, Shimo - Meguro, Meguro - ku,
Tokyo 153 - 0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 010 5879 8000
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1 - 800 - 441 - 2447 or 303 - 675 - 2140
Fax: 303 - 675 - 2150
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescalet and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004-2008. All rights reserved.
NOT RECOMMENDED FOR NEW DESIGN
NOT RECOMMENDED FOR NEW DESIGN
How to Reach Us:
MMG3003NT1
Document Number: MMG3003NT1
Rev. 7, 3/2008
18
RF Device Data
Freescale Semiconductor