ALSC AS7C251MNTD36A

January 2005
AS7C251MNTD32A
AS7C251MNTD36A
®
2.5V 1M × 32/36 Pipelined SRAM with NTDTM
Features
• Organization: 1,048,576 words × 32 or 36 bits
• NTD™architecture for efficient bus operation
• Fast clock speeds to 200 MHz
• Fast clock to data access: 3.2/3.5/3.8 ns
• Fast OE access time: 3.2/3.5/3.8 ns
• Fully synchronous operation
• pipelined mode
• Common data inputs and data outputs
• Asynchronous output enable control
• Available in 100-pin TQFP packages
• Byte write enables
• Clock enable for operation hold
• Multiple chip enables for easy expansion
• 2.5V core power supply
• Self-timed write cycles
• Interleaved or linear burst modes
• Snooze mode for standby operation
Logic block diagram
20
A[19:0]
D
Address
register
Burst logic
20
Q
CLK
D
Q
Write delay
addr. registers
CE0
CE1
CE2
20
CLK
R/W
BWa
Control
logic
DQ[a,b,c,d]
CLK
Write Buffer
BWb
BWc
BWd
ADV / LD
LBO
ZZ
CLK
32/36
D
1M x 32/36
SRAM
Array
32/36
Data Q
Input
Register
32/36
CLK
32/36
32/36
CLK
CEN
CLK
Output
Register
OE
32/36
OE
DQ[a,b,c,d]
Selection guide
-200
Minimum cycle time
-166
-133
Units
5
6
7.5
ns
Maximum clock frequency
200
166
133
MHz
Maximum clock access time
3.2
3.5
3.8
ns
Maximum operating current
450
400
350
mA
Maximum standby current
170
150
140
mA
Maximum CMOS standby current (DC)
90
90
90
mA
1/17/05, V 1.2
Alliance Semiconductor
P. 1 of 18
Copyright © Alliance Semiconductor. All rights reserved.
AS7C251MNTD32A
AS7C251MNTD36A
®
2.5V 32 Mb Synchronous SRAM products list1,2
Org
2MX18
1MX32
Part Number
AS7C252MPFS18A
AS7C251MPFS32A
Mode
PL-SCD
PL-SCD
Speed
200/166/133 MHz
200/166/133 MHz
1MX36
2MX18
1MX32
1MX36
2MX18
1MX32
1MX36
2MX18
1MX32
AS7C251MPFS36A
AS7C252MPFD18A
AS7C251MPFD32A
AS7C251MPFD36A
AS7C252MFT18A
AS7C251MFT32A
AS7C251MFT36A
AS7C252MNTD18A
AS7C251MNTD32A
PL-SCD
PL-DCD
PL-DCD
PL-DCD
FT
FT
FT
NTD-PL
NTD-PL
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
7.5/8.5/10 ns
7.5/8.5/10 ns
7.5/8.5/10 ns
200/166/133 MHz
200/166/133 MHz
1MX36
2MX18
1MX32
1MX36
AS7C251MNTD36A
AS7C252MNTF18A
AS7C251MNTF32A
AS7C251MNTF36A
NTD-PL
NTD-FT
NTD-FT
NTD-FT
200/166/133 MHz
7.5/8.5/10 ns
7.5/8.5/10 ns
7.5/8.5/10 ns
1 Core Power Supply: VDD = 2.5V + 0.125V
2 I/O Supply Voltage: VDDQ = 2.5V + 0.125V
PL-SCD
PL-DCD
FT
NTD1-PL
NTD-FT
:
:
:
:
:
Pipelined Burst Synchronous SRAM - Single Cycle Deselect
Pipelined Burst Synchronous SRAM - Double Cycle Deselect
Flow-through Burst Synchronous SRAM
Pipelined Burst Synchronous SRAM with NTDTM
Flow-through Burst Synchronous SRAM with NTDTM
1. NTD: No Turnaround Delay. NTDTM is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property
of their respective owners.
1/17/05, V 1.2
Alliance Semiconductor
P. 2 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Pin assignment
91
90
89
88
87
86
85
84
83
82
81
92
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
TQFP 14 x 20mm
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQPb/NC
DQb7
DQb6
VDDQ
VSSQ
DQb5
DQb4
DQb3
DQb2
VSSQ
VDDQ
DQb1
DQb0
VSS
NC
VDD
ZZ
DQa7
DQa6
VDDQ
VSSQ
DQa5
DQa4
DQa3
DQa2
VSSQ
VDDQ
DQa1
DQa0
DQPa/NC
LBO
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
A
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC/DQPc
DQc0
DQc1
VDDQ
VSSQ
DQc2
DQc3
DQc4
DQc5
VSSQ
VDDQ
DQc6
DQc7
VDD
VDD
NC
VSS
DQd0
DQd1
VDDQ
VSSQ
DQd2
DQd3
DQd4
DQd5
VSSQ
VDDQ
DQd6
DQd7
NC/DQPd
100
99
98
97
96
95
94
93
A
A
CE0
CE1
BWd
BWc
BWb
BWa
CE2
VDD
VSS
CLK
R/W
CEN
OE
ADV/LD
A
A
A
A
100-pin TQFP - top view
Note: For pins 1, 30, 51, and 80, NC applies to the x32 configuration. DQPn applies to the x36 configuration.
1/17/05, V 1.2
Alliance Semiconductor
P. 3 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Functional description
The AS7C251MNTD32A/36A family is a high performance CMOS 32 Mbit synchronous Static Random Access Memory (SRAM)
organized as 1,048,576 words × 32 or 36 bits and incorporates a LATE LATE Write.
This variation of the 32Mb+ synchronous SRAM uses the No Turnaround Delay (NTD™) architecture, featuring an enhanced write
operation that improves bandwidth over pipelined burst devices. In a normal pipelined burst device, the write data, command, and address
are all applied to the device on the same clock edge. If a read command follows this write command, the system must wait for two 'dead'
cycles for valid data to become available. These dead cycles can significantly reduce overall bandwidth for applications requiring random
access or read-modify-write operations.
NTD™ devices use the memory bus more efficiently by introducing a write latency which matches the two-cycle pipelined or one-cycle
flow-through read latency. Write data is applied two cycles after the write command and address, allowing the read pipeline to clear. With
NTD™, write and read operations can be used in any order without producing dead bus cycles.
Assert R/W low to perform write cycles. Byte write enable controls write access to specific bytes, or can be tied low for full 32/36 bit writes.
Write enable signals, along with the write address, are registered on a rising edge of the clock. Write data is applied to the device two clock
cycles later. Unlike some asynchronous SRAMs, output enable OE does not need to be toggled for write operations; it can be tied low for
normal operations. Outputs go to a high impedance state when the device is de-selected by any of the three chip enable inputs. In pipelined
mode, a two cycle deselect latency allows pending read or write operations to be completed.
Use the ADV (burst advance) input to perform burst read, write and deselect operations. When ADV is high, external addresses, chip select, R/W
pins are ignored, and internal address counters increment in the count sequence specified by the LBO control. Any device operations, including
burst, can be stalled using the CEN=1, the clock enable input.
The AS7C251MNTD32A/36A operates with a 2.5V ± 5% power supply for the device core (VDD). These devices are available in a 100-pin
TQFP package.
TQFP Capacitance
Parameter
Input capacitance
I/O capacitance
Symbol
Test conditions
CIN*
CI/O*
Min
Max
Unit
Vin = 0V
-
5
pF
Vin = Vout = 0V
-
7
pF
Units
°C/W
°C/W
°C/W
*Guaranteed not tested
TQFP thermal resistance
Description
Thermal resistance
(junction to ambient)1
Thermal resistance
(junction to top of case)1
Conditions
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA/JESD51
1–layer
Symbol
θJA
4–layer
θJA
Typical
40
22
θJC
8
1 This parameter is sampled
1/17/05, V 1.2
Alliance Semiconductor
P. 4 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Signal descriptions
Signal
I/O
Properties Description
CLK
I
CLOCK
CEN
I
SYNC
Clock. All inputs except OE, LBO, and ZZ are synchronous to this clock.
Clock enable. When de-asserted high, the clock input signal is masked.
A, A0, A1
I
SYNC
Address. Sampled when all chip enables are active and ADV/LD is asserted.
DQ[a,b,c,d]
I/O
SYNC
Data. Driven as output when the chip is enabled and OE is active.
CE0, CE1,
CE2
I
SYNC
Synchronous chip enables. Sampled at the rising edge of CLK, when ADV/LD is asserted.
Are ignored when ADV/LD is high.
ADV/LD
I
SYNC
Advance or Load. When sampled high, the internal burst address counter will increment in
the order defined by the LBO input value. When low, a new address is loaded.
R/W
I
SYNC
A high during LOAD initiates a READ operation. A low during LOAD initiates a WRITE
operation. Is ignored when ADV/LD is high.
BW[a,b,c,d]
I
SYNC
Byte write enables. Used to control write on individual bytes. Sampled along with WRITE
command and BURST WRITE.
OE
I
ASYNC
Asynchronous output enable. I/O pins are not driven when OE is inactive.
LBO
I
STATIC
Selects Burst mode. When tied to VDD or left floating, device follows interleaved Burst order. When
driven Low, device follows linear Burst order. This signal is internally pulled High.
ZZ
I
ASYNC
Snooze. Places device in low power mode; data is retained. Connect to GND if unused.
NC
-
-
No connect
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, ISB2 is guaranteed after the time tZZI is met. After entering SNOOZE MODE, all inputs except ZZ
is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete.
Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting
SNOOZE MODE during tPUS, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE
MODE.
1/17/05, V 1.2
Alliance Semiconductor
P. 5 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Burst order
Interleaved burst order (LBO = 1)
Linear burst order (LBO = 0)
A1 A0 A1 A0 A1 A0 A1 A0
A1 A0 A1 A0 A1 A0 A1 A0
Starting address
0 0
0 1
1 0
1 1
Starting Address
0 0
0 1
1 0
1 1
First increment
0 1
0 0
1 1
1 0
First increment
0 1
1 0
1 1
0 0
Second increment
1 0
1 1
0 0
0 1
Second increment
1 0
1 1
0 0
0 1
Third increment
1 1
1 0
0 1
00
Third increment
1 1
0 0
0 1
1 0
Synchronous truth table[5,6,7,8,9,11]
CE0
CE1 CE2 ADV/LD R/W
BWn
OE
CEN
Address
source
CLK
Operation
DQ
H
X
X
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
X
H
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
L
X
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
X
X
H
X
X
X
L
NA
L to H
CONTINUE DESELECT Cycle
High-Z
L
H
L
L
H
X
L
L
READ Cycle (Begin Burst)
Q
X
X
X
H
X
X
L
L
READ Cycle (Continue Burst)
Q
L
H
L
L
H
X
H
L
X
X
X
H
X
X
H
L
L
H
L
L
L
L
X
L
X
X
X
H
X
L
X
L
L
H
L
L
L
H
X
L
X
X
X
H
X
H
X
L
X
X
X
X
X
X
X
H
External L to H
Next
L to H
External L to H NOP/DUMMY READ (Begin Burst) High-Z
Next
L to H
External L to H
Next
L to H
DUMMY READ (Continue Burst)
L to H
1,10
2
High-Z 1,2,10
D
3
WRITE CYCLE (Continue Burst)
D
1,3,10
High-Z
2,3
WRITE ABORT (Continue Burst)
High-Z
1,2,3,
10
INHIBIT CLOCK
-
4
Current L to H
Key: X = Don’t Care, H = HIGH, L = LOW. BWn = H means all byte write signals (BWa, BWb, BWc, and BWd) are HIGH. BWn = L means one or
more byte write signals are LOW.
Notes:
1 CONTINUE BURST cycles, whether READ or WRITE, use the same control inputs. The type of cycle performed (READ or WRITE) is chose in the initial
BEGIN BURST cycle. A CONINUE DESELECT cycle can only be entered if a DESELECT CYCLE is executed first.
2 DUMMY READ and WRITE ABORT cycles can be considered NOPs because the device performs no external operation. A WRITE ABORT means a
WRITE command is given, but no operation is performed.
3 OE may be wired LOW to minimize the number of control signal to the SRAM. The device will automatically turn off the output drivers during a WRITE
cycle. OE may be used when the bus turn-on and turn-off times do not meet an application’s requirements.
4 If an INHIBIT CLOCK command occurs during a READ operation, the DQ bus will remain active (Low-Z). If it occurs during a WRITE cycle, the bus will
remain in High-Z. No WRITE operations will be performed during the INHIBIT CLOCK cycle.
5 BWa enables WRITEs to byte “a” (DQa pins); BWb enables WRITEs to byte “b” (DQb pins); BWc enables WRITEs to byte “c” (DQc pins); BWd
enables WRITEs to byte “d” (DQd pins).
6 All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
7 Wait states are inserted by setting CEN HIGH.
8 This device contains circuitry that will ensure that the outputs will be in High-Z during power-up.
9 The device incorporates a 2-bit burst counter. Address wraps to the initial address every fourth BURST CYCLE.
10 The address counter is incremented for all CONTINUE BURST cycles.
11 ZZ pin is always Low in this truth table.
1/17/05, V 1.2
1
WRITE CYCLE (Begin Burst)
External L to H NOP/WRITE ABORT (Begin Burst)
Next
Notes
Alliance Semiconductor
P. 6 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
State diagram for NTD SRAM
Read
Burst
Read
Read
ea
el
Ds
ite
Wr
Burst
Write
Burst
Dsel
W
rit
e
Dsel
Dsel
d
Write
Burst
Dsel
R
Write
Read
Write
Ds
el
Re
ad
Burst
Read
Burst
Write
Burst
Absolute maximum ratings
Parameter
Power supply voltage relative to GND
Input voltage relative to GND (input pins)
Input voltage relative to GND (I/O pins)
Power dissipation
Short circuit output current
Storage temperature
Temperature under bias
Symbol
VDD, VDDQ
VIN
VIN
Pd
IOUT
Tstg
Tbias
Min
–0.3
–0.3
–0.3
–
–
–65
–65
Max
+3.6
VDD + 0.3
VDDQ + 0.3
1.8
20
+150
+135
Unit
V
V
V
W
mA
oC
oC
Stresses greater than those listed under “Absolute maximum ratings” may cause permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions may affect reliability.
Recommended operating conditions
Parameter
Supply voltage for inputs
Supply voltage for I/O
Ground supply
1/17/05, V 1.2
Symbol
VDD
VDDQ
Vss
Min
2.375
2.375
0
Alliance Semiconductor
Nominal
2.5
2.5
0
Max
2.625
2.625
0
Unit
V
V
V
P. 7 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
DC electrical characteristics
Parameter
Input leakage current†
Output leakage current
Sym
|ILI|
|ILO|
Input high (logic 1) voltage
VIH
Input low (logic 0) voltage
VIL
Output high voltage
Output low voltage
VOH
VOL
Conditions
VDD = Max, 0V < VIN < VDD
OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ
Address and control pins
I/O pins
Address and control pins
I/O pins
IOH = –4 mA, VDDQ = 2.375V
IOL = 8 mA, VDDQ = 2.625V
Min
-2
-2
Max
2
2
Unit
µA
µA
1.7*
1.7*
-0.3**
-0.3**
1.7
–
VDD+0.3
VDDQ+0.3
0.7
0.7
–
0.7
V
V
V
V
V
V
† LBO and ZZ pins have an internal pull-up or pull-down, and input leakage = ±10 µA.
*
VIH max < VDD +1.5V for pulse width less than 0.2
**V min = -1.5 for pulse width less than 0.2 X t
IL
CYC
X tCYC
IDD operating conditions and maximum limits
Parameter
Operating power supply
current1
Sym
ICC
ISB
Standby power supply
current
Test conditions
CE0 < VIL, CE1 > VIH, CE2 < VIL, f = fMax,
IOUT = 0 mA, ZZ < VIL
All VIN ≤ 0.2V or > VDD – 0.2V, Deselected,
f = fMax, ZZ < VIL
-200
-166
-133
Unit
450
400
350
mA
170
150
140
ISB1
Deselected, f = 0, ZZ < 0.2V,
all VIN ≤ 0.2V or ≥ VDD – 0.2V
90
90
90
ISB2
Deselected, f = fMax, ZZ ≥ VDD – 0.2V,
all VIN ≤ VIL or ≥ VIH
80
80
80
mA
1 ICC given with no output loading. ICC increases with faster cycle times and greater output loading.
1/17/05, V 1.2
Alliance Semiconductor
P. 8 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Timing characteristics over operating range
-200
Parameter
Sym
-166
-133
Min
Max
Min
Max
Min
Max
Unit
200
–
166
–
133
MHz
Notes1
Clock frequency
FMAX
–
Cycle time
tCYC
5
–
6
–
7.5
–
ns
Clock access time
tCD
–
3.2
–
3.5
–
3.8
ns
Output enable low to data valid
tOE
–
3.2
–
3.5
–
3.8
ns
Clock high to output low Z
tLZC
0
–
0
–
0
–
ns
2,3,4
Data output invalid from clock high
tOH
1.5
–
1.5
–
1.5
–
ns
2
Output enable low to output low Z
tLZOE
0
–
0
–
0
–
ns
2,3,4
Output enable high to output high Z
tHZOE
–
3.0
–
3.4
–
3.8
ns
2,3,4
Clock high to output high Z
tHZC
–
3.0
–
3.4
–
3.8
ns
2,3,4
Output enable high to invalid output
tOHOE
0
–
0
–
0
–
ns
Clock high pulse width
tCH
2.0
–
2.4
–
2.4
–
ns
5
Clock low pulse width
tCL
2.0
–
2.4
–
2.4
–
ns
5
Address and Control setup to clock high
tAS
1.4
–
1.5
–
1.5
–
ns
6
Data setup to clock high
tDS
1.4
–
1.5
–
1.5
–
ns
6
Write setup to clock high
tWS
1.4
–
1.5
–
1.5
–
ns
6, 7
Chip select setup to clock high
tCSS
1.4
–
1.5
–
1.5
–
ns
6, 8
Address hold from clock high
tAH
0.4
–
0.5
–
0.5
–
ns
6
Data hold from clock high
tDH
0.4
–
0.5
–
0.5
–
ns
6
Write hold from clock high
tWH
0.4
–
0.5
–
0.5
–
ns
6, 7
Chip select hold from clock high
tCSH
0.4
–
0.5
–
0.5
–
ns
6, 8
Clock enable setup to clock high
tCENS
1.4
–
1.5
–
1.5
–
ns
6
Clock enable hold from clock high
tCENH
0.4
–
0.5
–
0.5
–
ns
6
ADV setup to clock high
tADVS
1.4
–
1.5
–
1.5
–
ns
6
ADV hold from clock high
tADVH
0.4
–
0.5
–
0.5
–
ns
6
1 See “Notes” on page 15
Snooze Mode Electrical Characteristics
Description
Current during Snooze Mode
ZZ active to input ignored
ZZ inactive to input sampled
ZZ active to SNOOZE current
ZZ inactive to exit SNOOZE current
1/17/05, V 1.2
Conditions
Symbol
ZZ > VIH
ISB2
tPDS
tPUS
tZZI
tRZZI
Alliance Semiconductor
Min
Max
Units
80
mA
cycle
cycle
cycle
2
2
2
0
P. 9 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Key to switching waveforms
Rising input
don’t care
Falling input
Undefined
Timing waveform of read cycle
tCH
tCL
tCYC
CLK
tCES tCEH
CEN
tAS
Address
tAH
A1
A2
A3
tWS tWH
R/W
tWS tWH
BWn
tCSH
CE0,CE2
CE1
tADVS tADVH
ADV/LD
OE
tOE
tLZOE
Dout
tHZOE
Q(A1)
tHLZC
Q(A2Y‘10)
Q(A2)
Q(A2Y‘11)
Q(A2Y‘01)
Read
Q(A1)
1/17/05, V 1.2
DSEL
Read
Q(A2)
Continue
Read
Q(A2Y‘01)
Continue
Read
Q(A2Y‘10)
Continue
Read
Q(A2Y‘11)
Alliance Semiconductor
Q(A3)
Inhibit
Clock
Read
Q(A3)
Continue
Read
Q(A3Y‘01)
P. 10 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Timing waveform of write cycle
tCH
tCL
tCYC
CLK
tCES tCEH
CEN
tAS
Address
tAH
A1
A2
A3
R/W
BWn
tCSH
CE0,CE2
CE1
tADVS tADVH
ADV/LD
OE
tDS
D(A1)
Din
tHZOE
Dout
Q(n-2)
D(A3)
D(A2Y‘01)
D(A2Y‘10)
D(A2Y‘11)
Q(n-1)
Write
D(A1)
1/17/05, V 1.2
tDH
D(A2)
DSEL
Write
D(A2)
Continue
Write
D(A2Y‘01)
Continue
Write
D(A2Y‘10)
Continue
Write
D(A2Y‘11)
Alliance Semiconductor
Inhibit
Clock
Write
D(A3)
Continue
Write
D(A3Y‘01)
P. 11 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Timing waveform of read/write cycle
tCH
tCL
tCYC
CLK
tCENS
tCENH
CEN
CE1
tCSS
tCSH
CE0, CE2
tADVS
tADVH
ADV/LD
tWS
tWH
tWS
tWH
tAS
tAH
R/W
BWn
ADDRESS
A1
A3
A2
A4
A6
A5
A7
tCD
tDS tDH
D/Q
D(A1)
tLZC
D(A2)
D(A2Ý01)
tOH
tOE
Q(A3)
Q(A4)
tHZC
Q(A4Ý01)
D(A5)
Q(A6)
tHZOE
tLZOE
OE
Command
Write
D(A1)
Write
D(A2)
Burst
Write
D(A2Ý01)
Read
Q(A3)
Read
Q(A4)
Burst
Read
Q(A4Ý01)
Write
D(A5)
Read
Q(A6)
Write
D(A7)
DSEL
Note: Ý = XOR when LBO = high/no connect. Ý = ADD when LBO = low. BW[a:d] is don’t care.
1/17/05, V 1.2
Alliance Semiconductor
P. 12 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
NOP, stall and deselect cycles
CLK
CEN
CE1
CE0, CE2
ADV/LD
R/W
BWn
Address
A2
A1
Q(A1)
D/Q
Command
Read
Q(A1)
Burst
Q(A1Ý01)
STALL
Q(A1Ý01)
Burst
Q(A1Ý10)
A3
D(A2)
Q(A1Ý10)
DSEL
Burst
DSEL
Write
D(A2)
Burst
NOP
D(A2Ý01)
Burst
D(A2Ý10)
Write
NOP
D(A3)
Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. OE is low.
1/17/05, V 1.2
Alliance Semiconductor
P. 13 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Timing waveform of snooze mode
CLK
tPUS
ZZ setup cycle
ZZ recovery cycle
ZZ
tZZI
Isupply
ISB2
tRZZI
All inputs
(except ZZ)
Deselect or Read Only
Deselect or Read Only
Normal
operation
Cycle
Dout
1/17/05, V 1.2
High-Z
Alliance Semiconductor
P. 14 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
AC test conditions
• Output load: For tLZC, tLZOE, tHZOE, and tHZC, see Figure C. For all others, see Figure B.
• Input pulse level: GND to 2.5V. See Figure A.
Thevenin equivalent:
• Input rise and fall time (measured at 0.25V and 2.25V): 2 ns. See Figure A.
• Input and output timing reference levels: 1.25V.
+2.5V
+2.5V
50Ω
90%
10%
GND
90%
DOUT
30 pF*
10%
Figure A: Input waveform
VL=VDDQ/2
Figure B: Output load (A)
319Ω/1667Ω
7Ω
5 pF*
DOUT
353Ω/1538Ω
GND *including scope
and jig capacitance
Figure C: Output load(B)
Notes
1) For test conditions, see “AC test conditions”, Figures A, B, and C
2) This parameter measured with output load condition in Figure C.
3) This parameter is sampled, but not 100% tested.
4) tHZOE is less than tLZOE, and tHZC is less than tLZC at any given temperature and voltage.
5) tCH is measured high above VIH, and tCL is measured low below VIL
6) This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK. All other synchronous inputs must
meet the setup and hold times with stable logic levels for all rising edges of CLK when chip is enabled.
7) Write refers to R/W and BW[a,b,c,d].
8) Chip select refers to CE0, CE1, and CE2.
1/17/05, V 1.2
Alliance Semiconductor
P. 15 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Package dimensions
100-pin quad flat pack (TQFP)
A1
A2
b
c
D
E
e
Hd
He
L
L1
α
Hd
D
TQFP
Min
Max
0.05
0.15
1.35
1.45
0.22
0.38
0.09
0.20
13.90 14.10
19.90 20.10
0.65 nominal
15.90 16.10
21.90 22.10
0.45
0.75
1.00 nominal
0°
7°
Dimensions in millimeters
b
e
He E
α
c
L1
A1 A2
L
1/17/05, V 1.2
Alliance Semiconductor
P. 16 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
Ordering information
Package & Width
TQFP x32
TQFP x36
–200 MHz
–166 MHz
–133 MHz
AS7C251MNTD32A-200TQC
AS7C251MNTD32A-166TQC
AS7C251MNTD32A-133TQC
AS7C251MNTD32A-200TQI
AS7C251MNTD32A-166TQI
AS7C251MNTD32A-133TQI
AS7C251MNTD36A-200TQC
AS7C251MNTD36A-166TQC
AS7C251MNTD36A-133TQC
AS7C251MNTD36A-200TQI
AS7C251MNTD36A-166TQI
AS7C251MNTD36A-133TQI
Note:
Add suffix ‘N’ to the above part number for Lead Free Parts (Ex. AS7C251MNTD32A-200TQCN)
Part numbering guide
AS7C
25
1M
NTD
32/36
A
–XXX
TQ
C/I
X
1
2
3
4
5
6
7
8
9
10
1. Alliance Semiconductor SRAM prefix
2. Operating voltage: 25 = 2.5V
3. Organization: 1M = 1M
4. NTD™ = No Turn-Around Delay. Pipelined mode
5. Organization: 32 = x 32, 36 = x 36
6. Production version: A = first production version
7. Clock speed (MHz)
8. Package type: TQ = TQFP
9. Operating temperature: C = commercial (0° C to 70° C); I = industrial (-40° C to 85° C)
10. N = Lead Free Part
1/17/05, V 1.2
Alliance Semiconductor
P. 17 of 18
AS7C251MNTD32A
AS7C251MNTD36A
®
®
Alliance Semiconductor Corporation
Copyright © Alliance Semiconductor
2575, Augustine Drive,
All Rights Reserved
Santa Clara, CA 95054
Tel: 408 - 855 - 4900
Part Number: AS7C251MNTD32A
AS7C251MNTD36A
Fax: 408 - 855 - 4999
Document Version: V 1.2
www.alsc.com
© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered
trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make
changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document.
The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this
data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The
information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate
as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application
or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including
liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express
agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according
to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask
works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical
components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the
inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify
Alliance against all claims arising from such use.