MTSS Series – 3.2 X 2.5 Ceramic SMD VCTCXO Low Profile SMD Device Hermetically Sealed Tight Stability Over Temperature Excellent Phase Noise 14.400MHZ TO 32.768MHZ Frequency Range Frequency Stability vs Temperature* Operating Temperature Range Storage Temperature Range (See Frequency Stability vs Temperature Table) (See Frequency Stability vs Temperature Table) -40°C to +85°C ±1.0 per year Aging 2.50VDC to +2.80VDC Supply Voltage +3.00VDC to 3.30VDC 2mA max Supply Current Output Type Clipped Sinewave Output Level 0.8 Vp-p min Output Load 10k Ohms//10pF Vc = +1.40VDC +0.40VDC to +2.40VDC Control Voltage Vc = +1.5VDC +0.50VDC to +2.50VDC ±8 ppm to ±15 ppm Frequency Tunning Range 100Hz 1kHz 10kHz Phase Noise -115dBc/Hz -135dBc/Hz -145dBc/Hz * Inclusive of Temperature., Load and Voltage Environmental & Mechanical Detail Shock Solderability Solvent Resistance MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 215 Vibration MIL-STD-883, Method 2007, Condition A Gross Leak Test MIL-STD-883, Method 1014, Condition C Fine Leak Test MIL-STD-883, Method 1014, Condition A-2 Marking Detail First Line = MXX.X (not to exceed 5 characters) M XX.X = MMD Device Frequency = (four digits including decimal point) Second Line = SYWW (not to exceed 5 characters) S YYWW = Internal Code = Date Code (Year/Week) MMD MONITOR/QUARTZEK – An ILSI Company, 5458 Louie Lane, Reno, NV 89511 Phone: (775) 851-8880, www.mmdcomp.com Revision: Revisions only with customer approval 07/31/13 K Pg 1 of 2 Part Number Guide MTS Frequency S 3.2 x 2.5 Ceramic SMD Output S = Clipped Sinewave Supply Voltage 3 = +3.0 VDC 2 = +2.8 VDC Frequency Stability 10 = ±1.0 ppm 15 = ±1.5 ppm 20 = ±2.0 ppm 25 = ±2.5 ppm 30 = ±3.0 ppm 50 = ±5.0 ppm Operating Temperature A = 0°C to +50°C C = -20°C to +70°C D = -30°C to +70°C E = -30°C to +80°C F = -40°C to +85°C G = 0°C to +70°C Pin 1 Connection V = Voltage Control Packaging T = Tape and Reel Please Consult with MMD Sales Department for any other Parameters or Options Mechanical Details Tape & Reel Dimensions PITCH 16.00 REEL DIA Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 PITCH TAPE WIDTH REEL DIA COUNT PIN 1 ORIENT. 4.00 [.157] 8.00 [.315] 180 [7.0] 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters [inch]. 3. Tolerances are ±0.1 [.004] mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD MONITOR/QUARTZEK – An ILSI Company, 5458 Louie Lane, Reno, NV 89511 Phone: (775) 851-8880, www.mmdcomp.com Revision: Revisions only with customer approval 07/31/13 K Pg 2 of 2