NTHS5402T1 Power MOSFET N-Channel ChipFET 4.9 Amps, 30 Volts Features • Low RDS(on) for Higher Efficiency • Miniature ChipFET Surface Mount Package http://onsemi.com 4.9 AMPS 30 VOLTS RDS(on) = 35 m Applications • Power Management in Portable and Battery–Powered Products; i.e., Cellular and Cordless Telephones and PCMCIA Cards D MAXIMUM RATINGS (TA = 25°C unless otherwise noted) Rating Symbol Steady State 5 secs Unit Drain–Source Voltage VDS 30 V Gate–Source Voltage VGS 20 V Continuous Drain Current (TJ = 150°C) (Note 1.) TA = 25°C TA = 85°C ID IS Maximum Power Dissipation (Note 1.) TA = 25°C TA = 85°C PD 2.1 N–Channel MOSFET A 1.1 A W 2.5 1.3 TJ, Tstg S 4.9 3.5 20 IDM Continuous Source Current (Diode Conduction) (Note 1.) Operating Junction and Storage Temperature Range A 6.7 4.8 Pulsed Drain Current G 1.3 0.7 ChipFET CASE 1206A STYLE 1 °C –55 to +150 1. Surface Mounted on 1″ x 1″ FR4 Board. MARKING DIAGRAM PIN CONNECTIONS 8 1 D 1 8 D 7 2 D 2 7 D 6 3 D 3 6 S 5 4 G 4 5 A8 D A8 = Specific Device Code ORDERING INFORMATION Semiconductor Components Industries, LLC, 2001 June, 2001 – Rev. 2 1 Device Package Shipping NTHS5402T1 ChipFET 3000/Tape & Reel Publication Order Number: NTHS5402T1/D NTHS5402T1 THERMAL CHARACTERISTICS Characteristic Symbol Maximum Junction–to–Ambient (Note 2.) t 5 sec Steady State RthJA Maximum Junction–to–Foot (Drain) Steady State RthJF Typ Max 40 80 50 95 15 20 Unit °C/W °C/W ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) Characteristic Symbol Test Condition Min Typ Max Unit VGS(th) VDS = VGS, ID = 250 µA 1.0 – – V Gate–Body Leakage IGSS VDS = 0 V, VGS = 20 V – – 100 nA Zero Gate Voltage Drain Current IDSS VDS = 24 V, VGS = 0 V – – 1.0 µA VDS = 24 V, VGS = 0 V, TJ = 85°C – – 5.0 ID(on) VDS 5.0 V, VGS = 10 V 20 – – A rDS(on) ( ) VGS = 10 V, ID = 4.9 A – 0.030 0.035 Ω VGS = 4.5 V, ID = 3.9 A – 0.045 0.055 gfs VDS = 10 V, ID = 4.9 A – 15 – S VSD IS = 1.1 A, VGS = 0 V – 0.8 1.2 V – 13 20 nC – 1.3 – Static Gate Threshold Voltage On–State Drain Current (Note 3.) Drain–Source On–State Resistance (Note 3.) Forward Transconductance (Note 3.) Diode Forward Voltage (Note 3.) Dynamic (Note 4.) Total Gate Charge Gate–Source Charge Qg VDS = 15 V V, VGS = 10 V V, ID = 4.9 A Qgs Gate–Drain Charge Qgd – 3.1 – Turn–On Delay Time td(on) – 10 15 – 10 15 – 25 40 – 10 15 – 30 60 Rise Time Turn–Off Delay Time tr td(off) Fall Time tf Source–Drain Reverse Recovery Time trr VDD = 15 V, RL = 15 Ω ID 1.0 1 0 A, A VGEN = 10 V V, RG = 6 Ω IF = 1.1 A, di/dt = 100 A/µs 2. Surface Mounted on 1″ x 1″ FR4 Board. 3. Pulse Test: Pulse Width 300 µs, Duty Cycle 2%. 4. Guaranteed by design, not subject to production testing. http://onsemi.com 2 ns NTHS5402T1 TYPICAL CHARACTERISTICS 20 20 4V 16 ID,Drain Current (A) ID,Drain Current (A) VGS = 10 thru 5 V 16 12 8 3V 12 8 TC125°C 4 4 0 0 25°C TC = –55°C 0 0.5 1.0 1.5 2.0 2.5 VDS, Drain–to–Source Voltage (V) 3.0 0 0.5 Figure 1. Output Characteristics 1.5 2.0 2.5 3.0 3.5 4.0 Figure 2. Transfer Characteristics 1200 0.10 1000 0.08 0.06 C, Capacitance (pF) r DS(on),On–Resistance ( Ω ) 1.0 VGS, Gate–to–Source Voltage (V) VGS = 4.5 V 0.04 VGS = 10 V 0.02 Ciss 800 600 400 Coss 200 Crss 0 0 0 4 8 12 ID, Drain Current (A) 16 20 0 6 12 18 24 VDS, Drain–to–Source Voltage (V) Figure 3. On–Resistance vs. Drain Current Figure 4. Capacitance 1.6 r DS(on),On–Resistance ( Ω ) (Normalized) VGS,Gate–to–Source Voltage (V) 10 VDS = 15 V ID = 4.9 A 8 6 4 2 0 30 0 3 6 9 Qg, Total Gate Charge (nC) 12 1.4 1.2 1.0 0.8 0.6 –50 15 VGS = 10 V ID = 4.9 A Figure 5. Gate Charge –25 0 25 50 75 100 TJ, Junction Temperature (°C) Figure 6. On–Resistance vs. Junction Temperature http://onsemi.com 3 125 150 NTHS5402T1 TYPICAL CHARACTERISTICS 0.10 20 rDS(on),On–Resistance ( Ω ) I S,Source Current (A) TJ = 150°C 10 TJ = 25°C 1 0.08 ID = 4.9 A 0.06 0.04 0.02 0 0 0.2 0.4 0.6 0.8 1.0 VSD, Source–to–Drain Voltage (V) 1.2 0 Figure 7. Source–Drain Diode Forward Voltage 10 Figure 8. On–Resistance vs. Gate–to–Source Voltage 0.4 50 0.2 40 ID = 250 µA –0.0 Power (W) V GS (th),Varience (V) 2 4 6 8 VGS, Gate–to–Source Voltage (V) –0.2 30 20 –0.4 10 –0.6 –0.8 –50 –25 0 25 50 75 100 TJ, Temperature (°C) 125 150 0 10–3 Figure 9. Threshold Voltage 10–2 10 –1 1 Time (sec) 10 100 Figure 10. Single Pulse Power http://onsemi.com 4 600 NTHS5402T1 TYPICAL CHARACTERISTICS Normalized Effective Transient Thermal Impedance 2 1 Duty Cycle = 0.5 Notes: 0.2 PDM t1 0.1 t2 0.1 t1 1. Duty Cycle, D = t 2 2. Per Unit Base = RthJA = 80°C/W 3. TJM – TA = PDMZthJA(t) 4. Surface Mounted 0.05 0.02 Single Pulse 0.01 10–4 10–3 10–2 10 –1 1 Square Wave Pulse Duration (sec) 10 100 600 Figure 11. Normalized Thermal Transient Impedance, Junction–to–Ambient Normalized Effective Transient Thermal Impedance 2 1 Duty Cycle = 0.5 0.2 0.1 0.1 0.05 0.02 Single Pulse 0.01 10–4 10–3 10–2 10 –1 Square Wave Pulse Duration (sec) 1 Figure 12. Normalized Thermal Transient Impedance, Junction–to–Foot http://onsemi.com 5 10 NTHS5402T1 80 mm 80 mm 18 mm 25 mm 68 mm 28 mm 28 mm 26 mm 26 mm Figure 13. Figure 14. BASIC PAD PATTERNS confines of the basic footprint. The drain copper area is 0.0054 sq. in. (or 3.51 sq. mm). This will assist the power dissipation path away from the device (through the copper leadframe) and into the board and exterior chassis (if applicable) for the single device. The addition of a further copper area and/or the addition of vias to other board layers will enhance the performance still further. The basic pad layout with dimensions is shown in Figure 13. This is sufficient for low power dissipation MOSFET applications, but power semiconductor performance requires a greater copper pad area, particularly for the drain leads. The minimum recommended pad pattern shown in Figure 14 improves the thermal area of the drain connections (pins 1, 2, 3, 6, 7, 8) while remaining within the http://onsemi.com 6 NTHS5402T1 PACKAGE DIMENSIONS ChipFET CASE 1206A–03 ISSUE C A 8 7 M 6 K 5 S 5 6 7 8 4 3 2 1 B 1 2 3 L 4 D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MOLD GATE BURRS SHALL NOT EXCEED 0.13 MM PER SIDE. 4. LEADFRAME TO MOLDED BODY OFFSET IN HORIZONTAL AND VERTICAL SHALL NOT EXCEED 0.08 MM. 5. DIMENSIONS A AND B EXCLUSIVE OF MOLD GATE BURRS. 6. NO MOLD FLASH ALLOWED ON THE TOP AND BOTTOM LEAD SURFACE. 7. 1206A-01 AND 1206A-02 OBSOLETE. NEW STANDARD IS 1206A-03. J G DIM A B C D G J K L M S C 0.05 (0.002) STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. http://onsemi.com 7 MILLIMETERS MIN MAX 2.95 3.10 1.55 1.70 1.00 1.10 0.25 0.35 0.65 BSC 0.10 0.20 0.28 0.42 0.55 BSC 5 ° NOM 1.80 2.00 DRAIN DRAIN DRAIN GATE SOURCE DRAIN DRAIN DRAIN INCHES MIN MAX 0.116 0.122 0.061 0.067 0.039 0.043 0.010 0.014 0.025 BSC 0.004 0.008 0.011 0.017 0.022 BSC 5 ° NOM 0.072 0.080 NTHS5402T1 ChipFET is a trademark of Vishay Siliconix ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 8 NTHS5402T1/D