ETC APT1204R7KLL

APT1204R7KLL
1200V 3.5A 4.70Ω
R
POWER MOS 7
MOSFET
®
Power MOS 7 is a new generation of low loss, high voltage, N-Channel
enhancement mode power MOSFETS. Both conduction and switching
®
losses are addressed with Power MOS 7 by significantly lowering RDS(ON)
®
and Qg. Power MOS 7 combines lower conduction and switching losses
along with exceptionally fast switching speeds inherent with APT's
patented metal gate structure.
• Lower Input Capacitance
• Lower Miller Capacitance
• Lower Gate Charge, Qg
TO-220
G
D
S
D
• Increased Power Dissipation
• Easier To Drive
• TO-220 Package
G
S
MAXIMUM RATINGS
Symbol
VDSS
ID
All Ratings: TC = 25°C unless otherwise specified.
Parameter
APT1204R7KLL
UNIT
1200
Volts
Drain-Source Voltage
3.5
Continuous Drain Current @ TC = 25°C
1
Amps
IDM
Pulsed Drain Current
VGS
Gate-Source Voltage Continuous
±30
Gate-Source Voltage Transient
±40
Total Power Dissipation @ TC = 25°C
135
Watts
Linear Derating Factor
1.08
W/°C
VGSM
PD
TJ,TSTG
14
Lead Temperature: 0.063" from Case for 10 Sec.
IAR
Avalanche Current
EAR
EAS
-55 to 150
Operating and Storage Junction Temperature Range
TL
1
3.5
1
Single Pulse Avalanche Energy
°C
300
(Repetitive and Non-Repetitive)
Repetitive Avalanche Energy
Volts
Amps
10
4
mJ
425
STATIC ELECTRICAL CHARACTERISTICS
ID(on)
RDS(on)
IDSS
IGSS
VGS(th)
MIN
Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA)
1200
Volts
3.5
Amps
On State Drain Current
2
(VDS > I D(on) x R DS(on) Max, VGS = 10V)
Drain-Source On-State Resistance
2
(VGS = 10V, 0.5 ID[Cont.])
TYP
MAX
4.70
Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V)
100
Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C)
500
Gate-Source Leakage Current (VGS = ±30V, VDS = 0V)
Gate Threshold Voltage (VDS = VGS, ID = 1mA)
Ohms
µA
±100
nA
5
Volts
3
CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
APT Website - http://www.advancedpower.com
UNIT
8-2002
BVDSS
Characteristic / Test Conditions
050-7120 Rev A
Symbol
DYNAMIC CHARACTERISTICS
Symbol
APT1204R7KLL
Characteristic
Test Conditions
MIN
TYP
MAX
Ciss
Input Capacitance
VGS = 0V
716
900
Coss
Output Capacitance
VDS = 25V
132
200
Crss
Reverse Transfer Capacitance
f = 1 MHz
36
60
VGS = 10V
31
50
VDD = 0.5 VDSS
4
5
ID = ID[Cont.] @ 25°C
21
40
Qg
Total Gate Charge
Q gs
3
Gate-Source Charge
Q gd
Gate-Drain ("Miller ") Charge
td(on)
Turn-on Delay Time
tr
Turn-off Delay Time
tf
VGS = 15V
7
14
2
4
ID = ID[Cont.] @ 25°C
20
30
RG = 1.6Ω
24
50
TYP
MAX
Fall Time
pF
nC
VDD = 0.5 VDSS
Rise Time
td(off)
UNIT
ns
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Symbol
IS
MIN
Characteristic / Test Conditions
3.5
Continuous Source Current (Body Diode)
ISM
Pulsed Source Current
1
(Body Diode)
14
VSD
Diode Forward Voltage
2
(VGS = 0V, IS = -ID[Cont.])
1.3
UNIT
Amps
Volts
t rr
Reverse Recovery Time (IS = -ID[Cont.], dl S/dt = 100A/µs)
400
ns
Q
rr
Reverse Recovery Charge (IS = -ID[Cont.], dl S/dt = 100A/µs)
2.5
µC
dt
Peak Diode Recovery dv/dt
dv/
5
10
V/ns
MAX
UNIT
THERMAL CHARACTERISTICS
Symbol
MIN
Characteristic
RθJC
Junction to Case
RθJA
Junction to Ambient
TYP
0.90
1 Repetitive Rating: Pulse width limited by maximum junction
temperature.
2 Pulse Test: Pulse width < 380 µs, Duty Cycle < 2%
3 See MIL-STD-750 Method 3471
4 Starting T = +25°C, L = 69.39mH, R = 25Ω, Peak I = 3.5A
j
G
L
5 dv/ numbers reflect the limitations of the test circuit rather than the
dt
device itself. IS ≤ -ID[Cont.] di/dt ≤ 700A/µs VR ≤ VDSS TJ ≤ 150°C
APT Reserves the right to change, without notice, the specifications and information contained herein.
0.9
050-7120 Rev A
0.2
0.1
0.05
0.05
0.02
Note:
0.01
0.01
SINGLE PULSE
PDM
Z JC, THERMAL IMPEDANCE (°C/W)
θ
8-2002
D=0.5
0.1
t1
t2
0.005
Duty Factor D = t1/t2
Peak TJ = PDM x ZθJC + TC
0.001
10-5
10-4
°C/W
40
10-3
10-2
10-1
1.0
RECTANGULAR PULSE DURATION (SECONDS)
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION
10
Typical Performance Curves
APT1204R7KLL
Graph Deleted
ID, DRAIN CURRENT (AMPERES)
8
VGS =15,10 & 8V
7
7V
6
5
6.5V
4
6V
3
2
5.5V
1
5V
0
0
5
10
15
20
25
30
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 3, LOW VOLTAGE OUTPUT CHARACTERISTICS
VDS> ID (ON) x RDS (ON)MAX.
250µSEC. PULSE TEST
@ <0.5 % DUTY CYCLE
8
6
TJ = -55°C
TJ = +125°C
4
TJ = +25°C
2
0
1
2
3
4
5
6
7
8
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 4, TRANSFER CHARACTERISTICS
3
2.5
2
1.5
1
0.5
0
50
75
100
125
150
TC, CASE TEMPERATURE (°C)
FIGURE 6, MAXIMUM DRAIN CURRENT vs CASE TEMPERATURE
2.5
25
NORMALIZED TO
= 10V @ 0.5 I [Cont.]
D
1.30
1.20
VGS=10V
1.10
1.00
VGS=20V
0.90
0.80
0
1
2
3
4
5
6
ID, DRAIN CURRENT (AMPERES)
FIGURE 5, RDS(ON) vs DRAIN CURRENT
I
D
= 0.5 I
D
V
GS
1.10
1.05
1.00
0.95
0.90
0.85
-50
-25
0
25
50 75 100 125 150
TJ, JUNCTION TEMPERATURE (°C)
FIGURE 7, BREAKDOWN VOLTAGE vs TEMPERATURE
1.2
[Cont.]
= 10V
2.0
1.5
1.0
0.5
0.0
-50 -25
0
25 50
75 100 125 150
TJ, JUNCTION TEMPERATURE (°C)
FIGURE 8, ON-RESISTANCE vs. TEMPERATURE
VGS(TH), THRESHOLD VOLTAGE
(NORMALIZED)
RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE
(NORMALIZED)
GS
1.15
BVDSS, DRAIN-TO-SOURCE BREAKDOWN
VOLTAGE (NORMALIZED)
ID, DRAIN CURRENT (AMPERES)
3.5
V
1.1
1.0
0.9
0.8
8-2002
0
1.40
0.7
0.6
-50 -25
0
25
50
75 100 125 150
TC, CASE TEMPERATURE (°C)
FIGURE 9, THRESHOLD VOLTAGE vs TEMPERATURE
050-7120 Rev A
ID, DRAIN CURRENT (AMPERES)
10
RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE
FIGURE 2, HIGH VOLTAGE OUTPUT CHARACTERISTICS
APT1204R7KLL
3,000
14
OPERATION HERE
LIMITED BY RDS (ON)
100µS
1,000
C, CAPACITANCE (pF)
ID, DRAIN CURRENT (AMPERES)
10
5
1mS
500
Coss
100
50
Crss
1
TC =+25°C
TJ =+150°C
SINGLE PULSE
0.5
10mS
16
0
10
20
30
40
50
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 11, CAPACITANCE vs DRAIN-TO-SOURCE VOLTAGE
I = I [Cont.]
D
D
12
VDS=100V
VDS=250V
8
VDS=400V
4
0
0
10
IDR, REVERSE DRAIN CURRENT (AMPERES)
1
10
100
1200
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 10, MAXIMUM SAFE OPERATING AREA
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
Ciss
5
10 15 20 25 30 35 40 45
Qg, TOTAL GATE CHARGE (nC)
FIGURE 12, GATE CHARGES vs GATE-TO-SOURCE VOLTAGE
100
50
TJ =+150°C
10
TJ =+150°C
TJ =+25°C
TJ =+25°C
1
0.3
0.5
0.7
0.9
1.1
1.3
1.5
VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS)
FIGURE 13, SOURCE-DRAIN DIODE FORWARD VOLTAGE
TO-220AC Package Outline
1.39 (.055)
0.51 (.020)
10.66 (.420)
9.66 (.380)
5.33 (.210)
4.83 (.190)
Drain
6.85 (.270)
5.85 (.230)
16.51 (.650)
14.23 (.560)
4.08 (.161) Dia.
3.54 (.139)
3.42 (.135)
2.54 (.100)
6.35 (.250)
MAX.
14.73 (.580)
12.70 (.500)
050-7120 Rev A
8-2002
0.50 (.020)
0.41 (.016)
Gate
Drain
Source
2.92 (.115)
2.04 (.080)
1.01 (.040) 3-Plcs.
0.38 (.015)
1.77 (.070) 3-Plcs.
1.15 (.045)
2.79 (.110)
2.29 (.090)
5.33 (.210)
4.83 (.190)
4.82 (.190)
3.56 (.140)
Dimensions in Millimeters and (Inches)
APT's devices are covered by one or more of the following U.S.patents:
4,895,810
5,256,583
5,045,903
4,748,103
5,089,434
5,283,202
5,182,234
5,231,474
5,019,522
5,434,095
5,262,336
5,528,058