JDSU PLRXPL-VC-SH4-21-N

COMMUNICATIONS MODULES & SUBSYSTEMS
8.5 G SFP+ 850 nm Limiting Transceiver,
8 Gigabit Fibre Channel Compliant
PLRXPL-VC-SH4-21-N and PLRXPL-VC-SH4-22-N Series
Key Features
• Compliant to industry-wide, 8 G Fibre Channel (FC) link
specifications
• Maintains FC compliance at 4 and 2 G without need for a
rate select option
• Uses a highly reliable, 850 nm oxide VCSEL
• Lead-free and RoHS 6/6-compliant
• 0 – 70°C case operating temperature
• Single 3.3 V power supply
• Low power consumption (typically 450 mW)
• Bit error rate < 1 x 10-12
• Hot pluggable
Applications
• High-speed storage area networks
- Switches and hubs
- Network interface cards
- Mass storage systems
- Host bus adapters
• Computer cluster crossconnect systems
• Custom high-bandwidth data pipes
Compliance
•
•
•
•
•
•
•
•
•
SFF 8431 Revision 2.2
FC-PI-4
SFF 8432 Revision 5.0
SFF 8472 Revision 10.3
CDRH and IEC60825-1 Class 1 Laser
Eye Safety
FCC Class B
ESD Class 2 per MIL-STD 883
Method 3015
UL 94, V0
Reliability tested per Telcordia GR-468
NORTH AMERICA: 800 498-JDSU (5378)
The lead-free and RoHS-compliant small form factor pluggable (SFP+)
transceiver from JDSU improves the performance for 8 Gigabit Fibre Channel (8
G FC) applications, and is ideal for high-speed, storage area network applications.
This transceiver features a highly reliable, 850 nm, oxide, vertical-cavity surfaceemitting laser (VCSEL) coupled to an LC optical connector. The transceiver is
fully compliant to the 8 G FC, FC-PI-4, and the SFP+ multisource agreement
(MSA) specifications, with internal AC coupling on both transmit and receive data
signals. The all-metal housing design provides low EMI emissions in demanding 8 G
applications and conforms to IPF specifications. An enhanced digital diagnostic
feature set allows for real-time monitoring of transceiver performance and system
stability, and the serial ID allows for customer and vendor system information to
be stored in the transceiver. Transmit disable, loss-of-signal, and transmitter fault
functions are also provided. The small size of the transceiver allows for highdensity system designs that, in turn, enable greater total bandwidth.
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
2
Section 1
Functional Description
The PLRXPL-VC-SH4-xx-N 8.5 G SFP+ 850 nm optical transceiver is designed to
transmit and receive 8B/10B scrambled 8.5 G serial optical data over 50/125 µm or
62.5/125 µm multimode optical fiber.
Transmitter
The transmitter converts 8B/10B scrambled serial PECL or CML electrical data into
serial optical data compliant with the 8 G Fibre Channel standard. Transmit data
lines (TD+ and TD-) are internally AC coupled, with 100 Ω differential termination.
Transmitter rate select (RS1) pin 9 is assigned to control the SFP+ module transmitter rate. It is connected internally to a 30 kΩ pull-down resistor. A data signal
on this pin does not affect the operation of the transmitter.
An open collector-compatible transmit disable (Tx_Disable) is provided. This pin
is internally terminated with a 10 kΩ resistor to Vcc,T. A logic “1,” or no connection, on this pin will disable the laser from transmitting. A logic “0” on this pin
provides normal operation.
The transmitter has an internal PIN monitor diode that ensures constant optical
power output, independent of supply voltage. It is also used to control the laser
output power over temperature to ensure reliability at high temperatures.
An open collector-compatible transmit fault (Tx_Fault) is provided. The Tx_
Fault signal must be pulled high on the host board for proper operation. A logic
“1” output from this pin indicates that a transmitter fault has occurred or that
the part is not fully seated and the transmitter is disabled. A logic “0” on this pin
indicates normal operation.
Receiver
The receiver converts 8B/10B scrambled serial optical data into serial PECL/CML
electrical data. Receive data lines (RD+ and RD-) are internally AC coupled with
100 Ω differential source impedance, and must be terminated with a 100 Ω differential load.
Receiver Rate Select (RS0) pin 7 is assigned to control the SFP+ module receiver
rate. It is connected internally to a 30 kΩ pull-down resistor. A data signal on this
pin has no affect on the operation of the receiver.
An open collector compatible loss of signal (LOS) is provided. The LOS must be
pulled high on the host board for proper operation. A logic “0” indicates that light
has been detected at the input to the receiver (see Optical Characteristics, Loss of
Signal Assert/Deassert Time). A logic “1” output indicates that insufficient light
has been detected for proper operation.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
3
10 kΩ
16 Transmitter
Power Supply
3 Transmitter
Disable In
VCC_TX TX_DIS
TOSA
Laser Driver
TX_GND
18 Transmitter
Positive Data
TD+
100 Ω
19 Transmitter
Negative Data
TD -
TX_FAULT
2 Transmitter
Fault Out
1, 17, 20 Transmitter
Signal Ground
5 SCL
Serial ID Clock
4 SDA
Serial ID Data
SCL
Management Processor
EEPROM
SDA
6 MOD_ABS
15 Receiver
Power Supply
VCC_RX
VCC_RX
RD -
50 Ω
Receiver
ROSA
RD +
RX_GND
RX_GND
50 Ω
LOS
12 Receiver
Negative Data Out
13 Receiver
Positive Data Out
8 Loss of Signal Out
9 RS1 TX Rate Select
Not Functional on
-N modules
30 kΩ
30 kΩ
7 RS0 RX Rate Select
Not Functional on
-N modules
10, 11, 14 Receiver
Signal Ground
Figure 1
SFP+ optical transceiver functional block diagram
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
4
Section 2
Application Schematic
Vcc
�
�
1 VeeT
VeeT 20
Vcc
�
�
�
Rp***
2 Tx Fault
TD- 19
3 Tx Disable
TD+ 18
�
�
�
�
R2* 50 Ω
CMOS, TTL, or
Open Collector Driver
(Tx Disable)
Power Supply Filter
Rx
VeeT 17
�
�
VccT 16
6 MOD_ABS
VccR 15
7 RS0
VeeR 14
8 LOS
RD+ 13
9 RS1
RD-
L2
C2
Vcc
CMOS or TTL Driver
(RS0 Rx Rate Select)
C4
Z* = 100 Ω
12
R3*
50 Ω
Vcc
R6 ∗∗
10 VeeR
VeeR 11
R4*
50 Ω
�
�
�
�
Receiver (LOS)
�
�
10 kΩ
Ry
�
�
�
�
Vcc
C5
C1
�
R5 ∗∗
Mod_ABS
�
Vcc
10 kΩ
�
5 SCL
�
***
Vcc +3.3V
Input
�
�
�
�
Rq
L1
C6
C3
�
4 SDA
Vcc
Open Collector
Bidirectional
SCL
PECL Driver
(TX DATA)
�
�
�
�
Receiver (Tx Fault)
Open Collector
Bidirectional
SDA
R1* 50 Ω
Z* = 100 Ω
10 kΩ
PECL Receiver
(RX DATA)
CMOS or TTL Driver
(RS1 Tx Rate Select)
Power supply filter component values are provided on page 7.
Figure 2
Recommended application schematic for the 10 G SFP+ optical transceiver
Notes

Power supply filtering components should be placed as close to the Vcc pins of the host connector as possible for optimal performance.

PECL driver and receiver components will require biasing networks. Please consult application notes from suppliers of these components. CML I/O on the PHY are supported. Good impedance matching for the driver and receiver is required.


SDA and SCL should be bi-directional open collector connections in order to implement serial ID in JDSU SFP+ transceiver modules.
R1/R2 and R3/R4 are normally included in the output and input of the PHY. Please check the application notes for the IC in use.
* Transmission lines should be 100 Ω differential traces. Vias and other transmission line discontinuities should be avoided. In order to meet the host TP1 output jitter and
TP4 jitter tolerance requirements it is recommended that the PHY has both transmitter pre-emphasis to equalize the transmitter traces and receiver equalization to equalize the
receiver traces. With appropriate transmitter pre-emphasis and receiver equalization, up to 8 dB of loss at 5 GHz can be tolerated.
** R5 and R6 are required when an Open Collector driver is used in place of CMOS or TTL drivers. 5 kΩ value is appropriate.
*** The value of Rp and Rq depend on the capacitive loading of these lines and the two wire interface clock frequency. See SFF-8431. A value of 10 kΩ is appropriate for 80 pF
capacitive loading at 100 kHz clock frequency.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
5
Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for
optimal performance. Vcc,R and Vcc,T should have separate filters.
Power supply filter component values from Figure 2 are shown in the table below
for two different implementations.
Power Supply Filter Component Values
Component
Option A
Option B
Units
L1, L2
Rx, Ry
C1, C5
C2, C3, C4
C6
1.0
0.5*
10
0.1
Not required
4.7
0.5*
22
0.1
22
µH
Ω
µF
µF
µF
Notes:
Option A is recommended for use in applications with space constraints with power supply noise less than 33 mVp-p.
Option B is used in the module compliance board in SFF-8431.
*If the total series resistance of L1+C6 and L2+C5 exceeds the values of Rx and Ry in the table, then Rx and Ry can be omitted.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
6
Section 3
Specifications
Technical specifications related to the SFP+ optical transceiver include:
• Section 3.1
Pin Function Definitions
• Section 3.2
Absolute Maximum Ratings
• Section 3.3
Operating Conditions
• Section 3.4
Electrical Characteristics
• Section 3.5
Optical Characteristics
• Section 3.6
Link Length
• Section 3.7
Regulatory Compliance
2.2 P IN F UNCTION D EFINITIONS
• Section 3.8
PCB Layout
• Section 3.9
Front Panel Opening
• Section
3.10 inModule
The transceiver pin descriptions as defined in SFF-8431
are shown
Figure 3 Outline
below. Table 2 on page 8 has a
•
Section
3.11
Transceiver
Belly-to-belly Mounting
complete description of all the pins.
Figure 3 Host PCB SFP+ Pad Assignment Top View
3.1
11
TOWARD HOST
WITH DIRECTION
OF MODULE
INSERTION
November 2007
21114472 R2
Pin Function Defi nitions
VEER
10
VEER
RS1
12
9
RD-
RX_LOS
8
13
RD+
RS0
7
14
VEER
MOD_ABS
6
15
VCCR
SCL
5
16
VCCT
17
VEET
18
TD+
19
TD-
20
VEET
Figure 3
SDA
4
TX_DISABLE
3
TX_FAULT
2
VEET
1
Host PCB SFP+ Pad assignment top view
TOWARD
BEZEL
PLRXPL-Vx-SH4-21xN
JDSU
| p. 7 of 20
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
7
SFP+ Optical Transceiver Pin Descriptions
Pin Number
Symbol
Name
Description
Receiver
8
LOS
Loss of Signal Out (OC)
10, 11, 14
12
VeeR
RD-
Receiver Signal Ground
Receiver Negative
DATA Out (PECL)
13
RD+
Receiver Positive
DATA Out (PECL)
15
VccR
Receiver Power Supply
7
RS0
RX Rate Select (LVTTL)
Sufficient optical signal for potential BER < 1x10-12 = Logic “0”
Insufficient optical signal for potential BER < 1x10-12 = Logic “1”
This pin is open collector compatible, and should be pulled up
to Host Vcc with a 10 kΩ resistor.
These pins should be connected to signal ground on the host board.
Light on = Logic “0” Output
Receiver DATA output is internally AC coupled and series
terminated with a 50 Ω resistor.
Light on = Logic “1” Output
Receiver DATA output is internally AC coupled and series
terminated with a 50 Ω resistor.
This pin should be connected to a filtered +3.3 V power supply
on the host board. See Application schematics on page 4 for
filtering suggestions.
This pin has an internal 30 kΩ pull-down to ground. A signal
on this pin will not affect module performance.
Transmitter
3
TX_Disable
Transmitter Disable In (LVTTL)
1, 17, 20
2
VeeT
TX_Fault
Transmitter Signal Ground
Transmitter Fault Out (OC)
16
VccT
Transmitter Power Supply
18
TD+
Transmitter Positive
DATA In (PECL)
19
TD-
Transmitter Negative
DATA In (PECL)
9
RS1
TX Rate Select (LVTTL)
Module Definition
4
SDA
Two-wire Serial Data
5
SCL
Two-wire Serial Clock
6
MOD_ABS
Module Absent
Logic “1” Input (or no connection) = Laser off
Logic “0” Input = Laser on
This pin is internally pulled up to VccT with a 10 kΩ resistor.
These pins should be connected to signal ground on the host board.
Logic “1” Output = Laser Fault (Laser off before t_fault)
Logic “0” Output = Normal Operation
This pin is open collector compatible, and should be pulled up
to Host Vcc with a 10 kΩ resistor.
This pin should be connected to a filtered +3.3 V power supply
on the host board. See Application schematics on page 4 for
filtering suggestions.
Logic “1” Input = Light on
Transmitter DATA inputs are internally AC coupled and
terminated with a differential 100 Ω resistor.
Logic “0” Input = Light on
Transmitter DATA inputs are internally AC coupled and
terminated with a differential 100 Ω resistor.
This pin has an internal 30 kΩ pulldown to ground. A signal
on this pin will not affect module performance.
Serial ID with SFF 8472 Diagnostics.
Module definition pins should be pulled up to Host Vcc with
appropriate resistors for the speed and capacitive loading of the
bus. See SFF8431.
Serial ID with SFF 8472 Diagnostics.
Module definition pins should be pulled up to Host Vcc with
appropriate resistors for the speed and capacitive loading of the
bus. See SFF8431.
Pin should be pulled up to Host Vcc with 10 kΩ resistor.
MOD_ABS is asserted “high” when the SFP+ module is
physically absent from the host slot.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
8
3.2
Absolute Maximum Ratings
Parameter
Symbol
Ratings
Unit
Storage temperature
Case temperature
Relative humidity
Transmitter differential input voltage
Power supply voltage
TST
TC
RH
VD
VCC
-40 to +95
-40 to +90
5 – 95 (non-condensing)
2.5
0 to +4.0
˚C
˚C
%
V
VP-P
Note:
Absolute maximum ratings represent the damage threshold of the device.
Damage may occur if the device is subjected to conditions beyond the limits stated here.
3.3
Operating Conditions
Part Number
Temperature Rating
Unit
PLRXPL-VC-SH4-xx-N
0 – 70
˚C
Note:
Performance is not guaranteed and reliability is not implied for operation at any condition outside these limits.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
9
3.4
Electrical Characteristics
Parameter
Symbol
Min.
Typical
Max.
Unit
Notes
Supply voltage
Vcc
2.97
3.3
3.63
V
All electrical and optical specifications
valid within this range
Power consumption
Data rate
Transmitter
Supply current
Common mode voltage tolerance
Data input deterministic jitter
Pdiss
480
8.5
1000
9.0
mW
Gbps
110
Data input total jitter
Input data dependent pulse
width shrinkage
Eye mask
TJ
DDPWS
0.31
0.11
mA
mVrms
UI(p-p) JSAT pattern. ∆T, BER < 1x10-12,
at 8.5 Gbps (Note 1)
UI
JSAT pattern. ∆T, at 8.5 Gbps (Note 1)
UI (p-p) JSAT pattern. ∆T, at 8.5 Gbps (Note 1)
X1
X2
Y1
Y2
VIH
VIL
0.155
0.5
Transmit disable voltage level
IccT
∆V
DJ
30
0.17
VOH
VOL
Transmit fault assert and reset times TFault
TReset
10
2
µs
ms
Vcc
0.4
V
V
100
µs
µs
90
2.0
-0.3
Transmit disable/enable assert time TTD
TTEN
Transmit fault output voltage level
350
Vcc + 0.3
0.8
UI
UI
mV
mV
V
V
Vcc - 0.4
-0.3
10
BER < 1x10-12
Reference FC-PI-4 Revision 7.1,
Figure 45
Laser output disabled after TTD if
input level is VIH; Laser output enabled
after TTEN if input level is VIL
Laser output disabled after TTD if
input level is VIH; Laser output enabled
after TTEN if input level is VIL
Transmit fault level is VOH and Laser
output disabled TFault after laser
fault. VOL is measured at 0.7 mA.
Transmitter fault is VOL and Laser
output restored TINI after
transmitter disable is asserted for
TReset, then disabled.
After hot plug or Vcc ≥ 2.97 V
Initialization time
Receiver
Supply current
Output common mode voltage
Data output deterministic jitter
Total jitter
TINI
300
ms
ICCR
DJ
TJ
120
30
0.42
0.71
Data dependent pulse width
shrinkage
Eye mask
DDPWS
0.36
mA
mVrms RLOAD = 25 Ω, differential
UI(p-p) JSAT pattern. ∆R, at 8.5 Gbps (Note 1, 4)
UI(p-p) JSAT pattern. ∆R, BER < 1x10-12,
at 8.5 Gbps (Note 1, 4)
UI (p-p) JSAT pattern. ∆R, at 8.5 Gbps
(Note 1, 4)
UI
Reference FC-PI-4 Revision 7.1,
mV
Figure 46
mV
V
LOS output level VOL TLOSD after light
input > LOSD (Note 2)
V
LOS output level VOH TLOSA after light
input < LOSA (Note 2)
µs
LOS output level VOL TLOSD after light
input > LOSD (Note 2)
µs
LOS output level VOH TLOSA after light
input < LOSA (Note 2)
Loss of signal voltage level
Loss of signal assert/deassert time
X1
Y1
Y2
VOH
0.355
Vcc -0.5
425
Vcc +0.3
VOL
-0.3
0.4
200
TLOSA
100
TLOSD
100
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
10
3.5
Optical Characteristics
Parameter
Transmitter
Wavelength
RMS spectral width
Transmitter waveform
dispersion penalty
Average optical power
Optical modulation amplitude
Relative intensity noise
Receiver
Wavelength
Maximum input power
Sensitivity (OMA)
Stressed sensitivity (OMA)
Loss of signal assert/deassert level
Low frequency cutoff
Symbol
Min.
Typical
Max.
Unit
Notes
λp
840
850
860
0.45
4.2
nm
nm
dB
(Note 3)
Note 6
dBm
µW
dB/Hz
12 dB reflection
nm
dBm
µWP-P
µWP-P
dBm
dBm
MHz
(Note 7)
(Note 4)
Chatter-free operation; LOSD is
OMA, LOSA is average power
-3 dB, P<-16 dBm
TWDP
PAVG
OMA
RIN12OMA
-8.2
302
λ
Pmax
S
VECP = 3.1 dB
LOSD
LOSA
FC
840
0
-128
850
860
76
151
-14
-30
0.3
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
11
3.6
Link Length
Data Rate Standard
Fiber Type
Modal Bandwidth at 850 nm (MHz*km)
Distance Range (m)
Notes
8.5 GBd
62.5/125 µm MMF
50/125 µm MMF
50/125 µm MMF
50/125 µm MMF
50/125 µm MMF
200
500
900
1500
2000
0.5 – 21
0.5 – 50
0.5 – 90
0.5 – 120
0.5 – 150
5
5
5
5
5
Specifi cation Notes
1. UI (unit interval): one UI is equal to one bit period. For example, 8.5 Gbps corresponds to a UI of 117.65 ps.
2. For LOSA and LOSD definitions, see Loss of Signal Assert/Deassert Level in Optical Characteristics.
3. Transmitter waveform and dispersion penalty is measured using the methods
specified in FC-PI-4 with a 1,0 equalizer and a 9.84-GHz, 3-dB optical bandwidth Gaussian filter for the fiber simulation.
4. Measured with stressed eye pattern as per FC-PI-4.
5. Distances, shown in the “Link Length” table, are calculated for worst-case fiber and transceiver characteristics based on the optical and electrical specifications shown in this document using techniques specified in IEEE 802.3. These
distances are consistent with those specified for FC-PI-4. In most cases, longer
distances are achievable.
6. The maximum transmitter output power is the lesser of the Class 1 laser eye
safety limit and the maximum receiver input power limit.
7. Sensitivity is for informational purposes only.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
12
3.7 Regulatory Compliance
The PLRXPL-VC-SH4-xx-N optical transceiver complies with international Electromagnetic Compatibility (EMC) and international safety requirements and
standards. EMC performance is dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis
for design decisions.
The PLRXPL-VC-SH4-xx-N optical transceiver is lead-free and RoHS-compliant
per Directive 2002/95/EC of the European Parliament and of the Council of 27
January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
Regulatory Compliance
Feature
Test Method
Performance
Component safety
UL 60950
UL 94, V0
IEC 60950
Directive 2002/95/EC
UL File E209897
RoHS-compliant
Laser eye safety1
Electromagnetic Compatibility
Electromagnetic emissions
EN 60825
U. S. 21CFR 1040.10
ESD immunity
EMC Directive 89/336/EEC
FCC CFR47 Part 15
IEC/CISPR 22
AS/NZS CISPR22
EN 55022
ICES-003, Issue 4
VCCI-03
EMC Directive 89/336/EEC
IEC/CISPR/24
EN 55024
EN 61000-4-2
Radiated immunity
EN 61000-4-3
Electromagnetic immunity
1. For further details, see Eye Safety
TUV Report/Certificate (CB scheme)
Compliant per the Directive 2002/95/EC of the European
Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in
electrical and electronic equipment.
TUV Certificate
CDRH compliant and Class 1 laser eye safe
Noise frequency range: 30 MHz to 40 GHz.
Good system EMI design practice required
to achieve Class B margins.
Exceeds requirements. Withstand discharges of 4 kV
contact and 8 kV air discharge to Criterion A, and 8 kV
contact and 25 kV air discharge to Criterion B.
Exceeds requirements. Field strength of 10 V/m RMS,
from 10 MHz to 1 GHz. No effect on transmitter/receiver
performance is detectable between these limits.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
13
3.8
PCB Layout
Figure 4
Board layout
ALL DIMENSIONS ARE IN MILLIMETERS
Figure 5
Detail layout
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
14
3.9
Front Panel Opening
Figure 6
3.10
Module Outline
ALL DIMENSIONS ARE IN MILLIMETERS
Figure 7
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
15
3.11 Transceiver Belly-to-belly Mounting
Figure 8
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
16
Section 4
Related Information
Other information related to the SFP+ optical transceiver includes:
• Section 4.1
• Section 4.2
• Section 4.3
• Section 4.4
4.1
Digital diagnostic monitoring and serial ID operation
Package and handling instructions
ESD discharge (ESD)
Eye safety
Digital Diagnostic Monitoring and Serial ID Operation
The PLRXPL-VC-SH4-xx-N optical transceiver is equipped with a two-wire serial EEPROM that is used to store specific information about the type and identification of the transceiver as well as real-time digitized information relating to
the transceiver’s performance. See the Small Form Factor Committee document
number SFF-8472 Revision 10.3, dated December 1, 2007 for memory/address
organization of the identification data and digital diagnostic data. The enhanced
digital diagnostics feature monitors five key transceiver parameters which are internally calibrated and should be read as absolute values and interpreted as follows:
Transceiver Temperature in degrees Celsius: Internally measured. Represented as
a 16 bit signed two’s complement value in increments of 1/256°C from -40 to
+70°C with LSB equal to 1/256°C. Accuracy is ± 3°C over the specified operating
temperature and voltage range.
Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16-bit unsigned
integer with the voltage defined as the full 16-bit value(0 – 65535) with LSB equal
to 100 uV with a measurement range of 0 to +6.55 V. Accuracy is ± three percent
of nominal value over the specified operating temperature and voltage ranges.
TX Bias Current in mA: Represented as a 16-bit unsigned integer with current de-
fined as the full 16-bit value (0 – 65535) with LSB equal to 2 uA with a measurement range of 0 – 131 mA. Accuracy is ± 10 percent of nominal value over the
specified operating temperature and voltage ranges.
TX Output Power in mW: Represented as a 16-bit unsigned integer with the power
defined as the full 16-bit value (0 – 65535) with LSB equal to 0.1 uW. Accuracy is ±
2 dB over the specified temperature and voltage ranges over the range of -10 dBm
to 0 dBm. Data is not valid when transmitter is disabled.
RX Received Optical Power in mW: Represented as average power as a 16-bit un-
signed integer with the power defined as the full 16-bit value (0 – 65535) with LSB
equal to 0.1 uW. Accuracy is ± 3 dB over the specified temperature and voltage
ranges over the power range of -14 dBm to 0 dBm.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
17
Reading the data
The information is accessed through the SCL and SDA connector pins of the module. The SFF-8431 Revision 2.2 specification contains all the timing and addressing information required for accessing the data in the EEPROM.
The device address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is 1010001X(A2h). Any other device addresses
will be ignored.
MOD_ABS, pin 6 on the transceiver, is connected to Logic 0 (Ground) on the
transceiver.
SCL, pin 5 on the transceiver, is connected to the SCL pin of the EEPROM.
SDA, pin 4 on the transceiver, is connected to the SDA pin of the EEPROM.
The EEPROM Write Protect pin is internally tied to ground with no external access, allowing write access to the customer-writable field (bytes 128 – 247 of address 1010001X). Note: address bytes 0 – 127 are not write protected and may
cause diagnostic malfunctions if written over.
Decoding the data
The information stored in the EEPROM, including the organization and the digital diagnostic information, is defined in the Small Form Factor Committee document SFF-8472 Revision 10.3, dated December 1, 2007.
Data Field Descriptions
0
Address( 1010000X)(A0h)
Serial ID Information;
Defined by SFP MSA
0
55
95
95
JDSU-Specific Information
127
119
127
Alarm and Warning Limits
Reserved for External
Calibration Constants
Real Time Diagnostic
Information
JDSU-Specific Information
Nonvolatile, customerwriteable, field-writeable
area
Reserved for SFP MSA
247
255
Address( 1010001X)(A2h)
255
JDSU-Specific Information
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
18
Serial ID Data and Map
Memory Address
Value
Comments
0
1
2
3-10
03
04
07
0000000020400C54
11
12
13
01
55
00
14
15
16
17
18
19
20-35
36
37-39
40-55
56-59
60-61
62
63
64
00
00
05
02
00
0F
JDSU
00
00019C
PLRXPLVCSH4xxN
65
66
67
68-83
84-91
92
1A
00
00
SFP Transceiver
SFP with Serial ID
LC Connector
Intermediate distance on OM3 fiber, short wave laser
without OFC, 50 and 62.5 µm fiber media, Fibre Channel
8, 4, and 2 Gbps compliant
8B/10B encoded
Nominal Bit rate of 8.5 Gbps
Rate Identifier (for Rate-selectable modules)
No rate select implemented
Single-mode fiber not supported
Single-mode fiber not supported
50 meters of OM2 50/125 µm multimode fiber
21 meters of OM1 62.5/125 µm multimode fiber
Copper not supported
150 meters of OM3 50/125 µm multimode fiber
Vendor Name (ASCII)
Reserved
IEEE Company ID (ASCII)
Part Number (ASCII), x = part number variable
Revision of part number (ASCII)
Wavelength of laser in nm; 850
Unallocated
Check Code; Lower 8 bits of sum from byte 0 through 62
Conventional uncooled laser, Class 1 power level,
Conventional limiting receiver output
Tx_Disable, Tx Fault, Loss of Signal implemented
93
F0
94
95
96-127
128-255
03
CC_EXT
0352
CC_BASE
00
68
Serial Number (ASCII)
Date Code (ASCII)
Diagnostic monitoring implemented, internally calibrated,
Receiver Power Measurement type is Average Power
Alarms and Warnings, TX_Fault and Rx_LOS monitoring
implemented, TX_Disable Control, and Monitoring.
SFF-8472 Revision 10.3 compliant
Check Code; Lower 8 bits of sum from byte 64 through 94
JDSU-specific EEPROM
Reserved for SFF-8079
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
19
Diagnostics Data Map
Memory Address
Value
Comments
00-01
02-03
04-05
06-07
08-09
10-11
12-13
14-15
16-17
18-19
20-21
22-23
24-25
26-27
28-29
30-31
32-33
34-35
36-37
38-39
40-55
56-59
60-63
64-67
68-71
72-75
76-77
78-79
80-81
82-83
84-85
86-87
88-89
90-91
92-94
95
96
97
98
99
100
Temp High Alarm
Temp Low Alarm
Temp High Warning
Temp Low Warning
Voltage High Alarm
Voltage Low Alarm
Voltage High Warning
Voltage Low Warning
Bias High Alarm
Bias Low Alarm
Bias High Warning
Bias Low Warning
TX Power High Alarm
TX Power Low Alarm
TX Power High Warning
TX Power Low Warning
RX Power High Alarm
RX Power Low Alarm
RX Power High Warning
RX Power Low Warning
Reserved
RP4
RP3
RP2
RP1
RP0
Islope
Ioffset
TPslope
TPoffset
Tslope
Toffset
Vslope
Voffset
Reserved
Checksum
Temperature MSB
Temperature LSB
Vcc MSB
Vcc LSB
TX Bias MSB (Note 1)
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
MSB at low address
For future monitoring quantities
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
External Calibration Constant
Reserved
Low order 8 bits of sum from 0 – 94
Internal temperature AD values
Internally measured supply voltage AD values
TX Bias Current AD values
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
20
Diagnostics Data Map
(continued)
Memory Address
Value
101
102
103
104
105
106
107
108
109
110-7
110-6
TX Bias LSB (Note 1)
TX Power MSB (Note 1)
TX Power LSB (Note 1)
RX Power MSB
RX Power LSB
Reserved MSB
Reserved LSB
Reserved MSB
Reserved LSB
Tx Disable State
Soft Tx Disable Control
110-5
110-4
110-3
110-2
110-1
110-0
111
112-119
120-127
128-247
248-255
Reserved
Rate Select State
Soft Rate Select Control
Tx Fault State
LOS State
Data Ready State
Reserved
Optional alarm & warning flag bits (Note 2)
Vendor specific
User/Customer EEPROM
Vendor specific
Comments
Measured TX output power AD values
Measured RX input power AD values
For 1st future definition of digitized analog input
For 2nd future definition of digitized analog input
Digital State of Tx Disable Pin
Writing “1” OR pulling the Tx_Disable pin will disable
the laser
Digital State of Rate Select Pin
Writing to this bit has no effect
Digital State
Digital State
Digital State; “1” until transceiver is ready
Reserved
Refer to SFF-8472 Revision 10.3
JDSU specific
Field writeable EEPROM
Vendor-specific control
Note :
1. During Tx disable, Tx bias and Tx power will not be monitored.
2. Alarm and warning are latched. The flag registers are cleared when the system Reads AND the alarm/warning condition no longer exists.
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
21
4.2 Package and Handling Instructions
This product is not compatible with any aqueous wash process.
Process plug
The PLRXPL-VC-SH4-xx-N optical transceiver is supplied with a process plug.
This plug protects the transceiver optics during standard manufacturing processes
by preventing contamination from air borne particles.
Note: It is recommended that the dust cover remain in the transceiver whenever an
optical fiber connector is not inserted.
Recommended cleaning and degreasing chemicals
JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning.
Do not use halogenated hydrocarbons (trichloroethane, ketones such as acetone,
chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol,
N-methylpyrolldone).
Flammability
The housing is made of cast zinc and sheet metal.
4.3 Electrostatic Discharge (ESD)
Handling
Normal ESD precautions are required during the handling of this module. This
transceiver is shipped in ESD protective packaging. It should be removed from the
packaging and handled only in an ESD protected environment utilizing standard
grounded benches, floor mats, and wrist straps.
Test and operation
In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly
installed in the system, this transceiver should meet and exceed common ESD
testing practices and fulfill system ESD requirements.
Typical of optical transceivers, this module’s receiver contains a highly sensitive
optical detector and amplifier which may become temporarily saturated during
an ESD strike. This could result in a short burst of bit errors. Such an event would
call for the application to reacquire synchronization at the higher layers (serializer/
deserializer chip).
8.5 G SFP+ 850 NM LIMITING TRANSCEIVER,
8 GIGABIT FIBRE CHANNEL COMPLIANT
4.4 Eye Safety
The PLRXPL-VC-SH4-xx-N Optical Transceiver is a CLASS 1 LASER PRODUCT
as defined by the international standard IEC 60825-1 Second Edition 2007-03 and
by U.S.A. regulations for Class 1 products per CDRH 21 CFR 1040.10 and 1040.11.
Laser emissions from Class 1 laser products are not considered hazardous when
operated according to product specifications. Operating the product with a power
supply voltage exceeding 4.0 volts may compromise the reliability of the product,
and could result in laser emissions exceeding Class 1 limits.
Caution
Tampering with this laser based product or operating this product outside the
limits of this specification may be considered an act of “manufacturing,” and will
require, under law, recertification of the modified product with the U.S. Food and
Drug Administration (21 CFR 1040).
The use of optical instruments with this product will increase eye hazard.
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at
[email protected].
Sample: PLRXPL-VC-SH4-21-N
Part Number
PLRXPL-VC-SH4-21-N
PLRXPL-VC-SH4-22-N
Product Description
8 G SFP+ SW, limiting electrical interface, 0 – 70˚C, ± 10% Vcc, no rate select, generic, first generation
8 G SFP+ SW, limiting electrical interface, 0 – 70˚C, ± 10% Vcc, no rate select, generic, second generation
NORTH AMERICA: 800 498-JDSU (5378)
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com
Product specifications and descriptions in this document subject to change without notice. © 2008 JDS Uniphase Corporation 30149341 501 1008 PLRXPL-VX-SH4-XX-N.DS.CMS.AE
October 2008