FKBP200 - FKBP210 FAST RECOVERY BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 2.0 Amperes KBP 0.71 (18.0) 0.63 (16.0) FEATURES : * * * * * * * High case dielectric strength of 2000 V DC High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Ideal for printed circuit board 0.825 (20.95) 0.605 (15.36) + AC AC 0.035 (0.89) 0.028 (0.71) 0.500 (12.7) 0.16 (4.00) 0.14 (3.55) 0.276 (7.01 ) 0.236 (5.99) 0.105 (2.66) 0.085 (2.16) MECHANICAL DATA : * Case : Reliable low cost construction utilizing molded plastic technique * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL - STD 202 , Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 3.4 grams Dimensions in inches and ( millimeter ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL FKBP FKBP FKBP FKBP FKBP FKBP FKBP 200 201 202 204 206 208 210 UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts Maximum Average Forward Current Tc = 50 °C IF(AV) 2.0 Amps. IFSM 35 Amps. 2 Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Current Squared Time at t < 8.3 ms. Maximum Forward Voltage drop per Diode at IF = 1.0 Amp. Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) 2 It VF 10 AS 1.3 Volts IR 10 µA I R(H) Trr µA 500 150 250 500 ns 30 °C/W Operating Junction Temperature Range RθJA TJ - 50 to + 150 °C Storage Temperature Range T STG - 50 to + 150 °C Typical Thermal Resistance (Note 2) Notes : 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Thermal resistance from Junction to Ambient on P.C. Board with, 0.47" X 0.47" ( 12 mm. x 12 mm. ) Cu. pads. UPDATE : APRIL 21, 1998 RATING AND CHARACTERISTIC CURVES ( FKBP200 - FKBP210 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 2.5 2.0 1.5 1.0 0.5 Tc = 50 °C 40 30 20 10 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 2 CASE TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS 6 10 20 40 60 100 FIG.5 - TYPICAL REVERSE CHARACTERISTICS PER DIODE REVERSE CURRENT, MICROAMPERES PER DIODE 100 FORWARD CURRENT, AMPERES 4 NUMBER OF CYCLES AT 60Hz Pulse Width = 300 µs 2% Duty Cycle TJ = 25 °C 10 1.0 0.1 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS 1.8 2.0