F2W005G - F2W10G PRV : 50 - 1000 Volts Io : 2.0 Amperes FAST RECOVERY GLASS PASSIVATED BRIDGE RECTIFIERS WOB FEATURES : 0.39 (10.0) 0.31 (7.87) Glass passivated chip High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Ideal for printed circuit board 0.22 (5.59) 0.18 (4.57) + - AC 1.00 (25.4) MIN. 1.10 (27.9) MIN. * * * * * * * * 0.034 (0.86) 0.028 (0.71) MECHANICAL DATA : * Case : Reliable low cost construction utilizing molded plastic technique * Epoxy : UL94V-O rate flame retardant * Terminals : Plated leads solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 1.29 grams AC + - 0.22 (5.59) 0.18 (4.57) AC 0.22 (5.59) 0.18 (4.57) Dimension in inches and (millimeter) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL F2W F2W 005G 01G 50 100 F2W 02G 200 F2W 04G 400 F2W 06G 600 F2W 08G 800 F2W 10G 1000 UNIT Maximum Recurrent Peak Reverse Voltage VRRM Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts Maximum Average Forward Current 0.375" (9.5 mm) lead length Tc = 50°C IF(AV) 2.0 Amps. IFSM 30 Amps. 2 10 A2S Volts Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Rating for fusing ( t < 8.3 ms. ) Maximum Forward Voltage per Diode at IF = 1.0 Amp. It VF 1.3 Maximum DC Reverse Current Ta = 25 °C IR 10 µA at Rated DC Blocking Voltage Ta = 100 °C IR(H) 1.0 mA Maximum Reverse Recovery Time (Note 1) Trr Typical Junction Capacitance per Diode (Note 2) CJ 24 pf RθJA TJ 36 °C/W Operating Junction Temperature Range - 50 to + 150 °C Storage Temperature Range TSTG - 50 to + 150 °C Typical Thermal Resistance (Note 3) Notes : 150 250 500 ns 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 3 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board with, 0.22" x 0.22" (5.5 x 5.5 mm) copper Pads. UPDATE : AUGUST 23,1998 RATING AND CHARACTERISTIC CURVES ( F2W005G - F2W10G ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω Trr + 0.5 A D.U.T. + PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω 0 - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 1 cm 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PC Board 0.375(9.5mm) 1.6 Copper Pads 0.22" x 0.22" (5.5 x5.5mm) 1.2 0.8 0.4 60 Hz, Resistive or Inductive load. 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 2.0 24 TJ = 55 °C 18 12 0 175 SINGLE HALF SINE WAVE (JEDEC METHOD) 6 1 CASE TEMPERATURE, ( °C) 20 10 1 TJ = 25 °C Pulse Width = 300 µs 1 % Duty Cycle 0.01 0.4 0.8 1.2 1.6 2.0 2.4 2.8 FORWARD VOLTAGE, VOLTS 4 6 10 20 40 60 100 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES FIG.4 - TYPICAL FORWARD CHARACTERISTICS 0.1 2 NUMBER OF CYCLES AT 60Hz 3.2 10 TJ = 100 °C 1.0 TJ = 25 °C 0.1 0.01 0 20 40 60 80 100 120 PERCENT OF RATED REVERSE VOLTAGE, (%) 140