Revised November 1999 74ACTQ08 Quiet Series Quad 2-Input AND Gate General Description Features The ACTQ08 contains four, 2-input AND gates and utilizes Fairchild Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet Series features GTO output control and undershoot corrector in addition to a split ground bus for superior ACMOS performance. ■ ICC reduced by 50% ■ Guaranteed simultaneous switching noise level and dynamic threshold performance ■ Improved latch-up immunity ■ Outputs source/sink 24 mA ■ TTL-compatible inputs Ordering Code: Order Number Package Number Package Description 74ACTQ08SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body 74ACTQ08SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74ACTQ08PC N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Logic Symbol Connection Diagram IEEE/IEC Pin Descriptions Pin Names Description An, Bn Inputs On Outputs FACT, Quiet Series, FACT Quiet Series and GTO are trademarks of Fairchild Semiconductor Corporation. © 1999 Fairchild Semiconductor Corporation DS010891 www.fairchildsemi.com 74ACTQ08 Quiet Series Quad 2-Input AND Gate August 1990 74ACTQ08 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions −0.5V to +7.0V Supply Voltage (VCC) DC Input Diode Current (IIK) VI = −0.5V −20 mA VI = VCC + 0.5V +20 mA Supply Voltage (VCC) 0V to VCC −40°C to +85°C Operating Temperature (TA) DC Output Diode Current (IOK) Minimum Input Edge Rate (∆V/∆t) VO = −0.5V −20 mA VO = VCC + 0.5V 125 mV/ns VIN from 0.8V to 2.0V +20 mA DC Output Voltage (VO) 0V to VCC Output Voltage (VO) −0.5V to VCC + 0.5V DC Input Voltage (VI) 4.5V to 5.5V Input Voltage (VI) VCC @ 4.5V, 5.5V −0.5V to VCC + 0.5V DC Output Source ± 50 mA or Sink Current (IO) DC VCC or Ground Current ± 50 mA per Output Pin (ICC or IGND) Storage Temperature (TSTG) Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation outside of databook specifications. −65°C to +150°C DC Latch-Up Source or Sink Current ± 300 mA Junction Temperature (TJ) PDIP 140°C DC Electrical Characteristics Symbol VIH VIL VOH Parameter Minimum HIGH Level VCC TA = +25°C (V) Typ 4.5 1.5 TA = −40°C to +85°C Guaranteed Limits 2.0 2.0 Input Voltage 5.5 1.5 2.0 2.0 Maximum LOW Level 4.5 1.5 0.8 0.8 Input Voltage 5.5 1.5 0.8 0.8 Minimum HIGH Level 4.5 4.49 4.4 4.4 Output Voltage 5.5 5.49 5.4 5.4 Units V V V Conditions VOUT = 0.1V or VCC − 0.1V VOUT = 0.1V or VCC − 0.1V IOUT = −50 µA VIN = VIL or VIH VOL 4.5 3.86 3.76 5.5 4.86 4.76 Maximum LOW Level 4.5 0.001 0.1 0.1 Output Voltage 5.5 0.001 0.1 0.1 0.36 0.44 V IOH = −24 mA IOH = −24 mA (Note 2) V IOUT = 50 µA V IOL = 24 mA VIN = VILor VIH 4.5 IOL = 24 mA (Note 2) 5.5 0.36 0.44 IIN Maximum Input Leakage Current 5.5 ± 0.1 ± 1.0 µA VI = VCC, GND ICCT Maximum ICC/Input 5.5 1.5 mA VI = VCC − 2.1V IOLD Minimum Dynamic 5.5 75 mA VOLD = 1.65V Max IOHD Output Current (Note 3) 5.5 −75 mA VOHD = 3.85V Min 20.0 µA VIN = VCC or GND 0.6 ICC Maximum Quiescent Supply Current 5.5 VOLP Quiet Output Maximum Dynamic VOL 2.0 5.0 1.1 1.5 V Figure 1, Figure 2 (Note 4)(Note 5) VOLV Quiet Output Minimum Dynamic VOL 5.0 −0.6 −1.2 V Figure 1, Figure 2 (Note 4)(Note 5) VIHD Minimum HIGH Level Dynamic Input Voltage 5.0 1.9 2.2 V (Note 4)(Note 6) VILD Maximum LOW Level Dynamic Input Voltage 5.0 1.2 0.8 V (Note 4)(Note 6) Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: DIP package. Note 5: Max number of outputs defined as (n). Data inputs are 0V to 3V. One output @ GND. Note 6: Max number of data inputs (n) switching. (n−1) inputs switching 0V to 3V (ACTQ). Input-under-test switching: 3V to threshold (VILD), 0V to threshold (VIHD), f = 1 MHz. www.fairchildsemi.com 2 Symbol Parameter VCC TA = +25°C (V) CL = 50 pF TA = −40°C to +85°C CL = 50 pF (Note 7) Min Typ Max Min Max Units tPLH Propagation Delay Data to Output 5.0 2.5 6.0 6.5 2.5 7.0 ns tPHL Propagation Delay Data to Output 5.0 2.5 6.0 6.5 2.5 7.0 ns tOSHL Output to Output tOSLH Skew (Note 8) 0.5 1.0 1.0 ns 5.0 Note 7: Voltage Range 5.0 is 5.0V ± 0.5V. Note 8: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH). Parameter guaranteed by design. Capacitance Typ Units CIN Symbol Input Capacitance Parameter 4.5 pF VCC = OPEN CPD Power Dissipation Capacitance 70 pF VCC = 5.0V 3 Conditions www.fairchildsemi.com 74ACTQ08 AC Electrical Characteristics 74ACTQ08 FACT Noise Characteristics The setup of a noise characteristics measurement is critical to the accuracy and repeatability of the tests. The following is a brief description of the setup used to measure the noise characteristics of FACT. VOLP/VOLV and VOHP/VOHV: • Determine the quiet output pin that demonstrates the greatest noise levels. The worst case pin will usually be the furthest from the ground pin. Monitor the output voltages using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. Equipment: Hewlett Packard Model 8180A Word Generator PC-163A Test Fixture • Measure VOLP and VOLV on the quiet output during worst case transition for active and enable. Measure VOHP and VOHV on the quiet output during the worst case active and enable transition. Tektronics Model 7854 Oscilloscope Procedure: 1. Verify Test Fixture Loading: Standard Load 50 pF, 500Ω. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. 2. Deskew the HFS generator so that no two channels have greater than 150 ps skew between them. This requires that the oscilloscope be deskewed first. It is important to deskew the HFS generator channels before testing. This will ensure that the outputs switch simultaneously. VILD and VIHD: • Monitor one of the switching outputs using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. 3. Terminate all inputs and outputs to ensure proper loading of the outputs and that the input levels are at the correct voltage. • First increase the input LOW voltage level, VIL, until the output begins to oscillator steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input LOW voltage level at which oscillation occurs is defined as VILD. 4. Set the HFS generator to toggle all but one output at a frequency of 1 MHz. Greater frequencies will increase DUT heating and effect the results of the measurement. • Next decrease the input HIGH voltage level, VIH, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input HIGH voltage level at which oscillation occurs is defined as V IHD. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. VOHV and VOLP are measured with respect to ground reference. Input pulses have the following characteristics: f = 1 MHz, tr = 3 ns, tf = 3 ns, skew < 150 ps. FIGURE 1. Quiet Output Noise Voltage Waveforms 5. Set the HFS generator input levels at 0V LOW and 3V HIGH for ACT devices and 0V LOW and 5V HIGH for AC devices. Verify levels with an oscilloscope. FIGURE 2. Simultaneous Switching Test Circuit www.fairchildsemi.com 4 74ACTQ08 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body Package Number M14A 5 www.fairchildsemi.com 74ACTQ08 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M14D www.fairchildsemi.com 6 74ACTQ08 Quiet Series Quad 2-Input AND Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide Package Number N14A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 7 www.fairchildsemi.com