Revised September 1998 74ACQ241 Octal Buffer/Line Driver with 3-STATE Outputs General Description Features The ACQ241 is an octal buffer and line driver designed to be employed as a memory address driver, clock driver and bus oriented transmitter or receiver which provides improved PC board density. The ACQ utilizes Fairchild FACT Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet Series features GTO output control and undershoot corrector in addition to a split ground bus for superior performance. ■ ICC and IOZ reduced by 50% ■ Guaranteed simultaneous switching noise level and dynamic threshold performance ■ Guaranteed pin-to-pin skew AC performance ■ Improved latch-up immunity ■ 3-STATE outputs drive bus lines or buffer memory address registers ■ Outputs source/sink 24 mA ■ Faster prop delays than the standard AC Ordering Code: Order Number Package Number Package Description 74ACQ241SC M20B 20-Lead Small Outline Integrated Circuit, JEDEC MS-013, 0.300” Wide Body 74ACQ241PC N20A 20-Lead Plastic Dual-In-Line Package, JEDEC MS-001, 0.300” Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Logic Symbol Pin Descriptions IEEE/IEC Pin Names Description OE1, OE2 3-STATE Output Enable Inputs I0–I7 Inputs O0–O7 Outputs Truth Tables Inputs In OE1 Connection Diagram Pin Assignment for DIP and SOIC Outputs (Pins 12, 14, 16, 18) L L L L H H H X Z Inputs Outputs OE2 In (Pins 3, 5, 7, 9) H L L H H H H X H = HIGH Voltage Level L = LOW Voltage Level Z X = Immaterial Z = High Impedance FACT, FACT Quiet Series, and GTO are trademarks of Fairchild Semiconductor Corporation. © 1998 Fairchild Semiconductor Corporation DS010642.prf www.fairchildsemi.com 74ACQ241 Octal Buffer/Line Driver with 3-STATE Outputs January 1990 74ACQ241 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC ) Recommended Operating Conditions −0.5V to +7.0V DC Input Diode Current (IIK) VI = −0.5V −20 mA VI = VCC + 0.5V +20 mA DC Input Voltage (VI) Supply Voltage (VCC) −0.5V to VCC + 0.5V VO = −0.5V VO = VCC + 0.5V DC Output Voltage (VO) −20 mA per Output Pin (ICC or IGND) +20 mA Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT circuits outside databook specifications. ± 50 mA ± 50 mA −65°C to +150°C ±300 mA Junction Temperature (TJ) PDIP www.fairchildsemi.com 125 mV/ns VCC @ 3.0V, 4.5V, 5.5V −0.5V to VCC + 0.5V DC Latch-Up Source or Sink Current −40°C to +85°C VIN from 30% to 70% of VCC DC VCC or Ground Current Storage Temperature (TSTG) 0V to VCC Operating Temperature (TA) DC Output Source or Sink Current (IO) 0V to VCC Output Voltage (VO) Minimum Input Edge Rate ∆V/∆t DC Output Diode Current (IOK) 2.0V to 6.0V Input Voltage (VI) 140°C 2 Symbol Parameter VCC (V) VIH VIL VOH TA = +25°C Typ TA = −40°C to +85°C Units Conditions Guaranteed Limits Minimum High Level 3.0 1.5 2.1 2.1 Input Voltage 4.5 2.25 3.15 3.15 5.5 2.75 3.85 3.85 Maximum Low Level 3.0 1.5 0.9 0.9 Input Voltage 4.5 2.25 1.35 1.35 5.5 2.75 1.65 1.65 Minimum High Level 3.0 2.99 2.9 2.9 Output Voltage 4.5 4.49 4.4 4.4 5.5 5.49 5.4 5.4 3.0 2.56 2.46 4.5 3.86 3.76 5.5 4.86 4.76 VOUT = 0.1V V or VCC − 0.1V VOUT = 0.1V V or VCC − 0.1V IOUT = −50 µA V VIN = VIL or VIH VOL IOH = −12 mA V IOH = −24 mA IOH = −24 mA (Note 2) IOUT = 50 µA Maximum Low Level 3.0 0.002 0.1 0.1 Output Voltage 4.5 0.001 0.1 0.1 5.5 0.001 0.1 0.1 3.0 0.36 0.44 4.5 0.36 0.44 5.5 0.36 0.44 5.5 ± 0.1 ± 1.0 µA VI = VCC, GND 75 mA VOLD = 1.65V Max V VIN = VIL or VIH IOL = 12 mA V IOL = 24 mA IOL = 24 mA (Note 2) IIN (Note 4) Maximum Input Leakage Current IOLD Minimum Dynamic Output Current 5.5 IOHD (Note 3) 5.5 −75 mA VOHD = 3.85V Min ICC (Note 4) Maximum Quiescent Supply Current 5.5 4.0 40.0 µA VIN = VCC or GND IOZ Maximum 3-STATE 5.5 ±0.25 ±2.5 µA VI (OE) = VIL, VIH VI = VCC, GND Leakage Current VO = VCC, GND VOLP Quiet Output 5.0 1.1 1.5 V Maximum Dynamic VOL VOLV Quiet Output 5.0 −0.6 −1.2 V Figures 1, 2 5.0 3.1 3.5 V (Note 5)(Note 7) 5.0 1.9 1.5 V (Note 5)(Note 7) Minimum Dynamic VOL VIHD Minimum High Level Figures 1, 2 (Note 5)(Note 6) (Note 5)(Note 6) Dynamic Input Voltage VILD Maximum Low Level Dynamic Input Voltage Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. Note 5: DIP package. Note 6: Max number of outputs defined as (n). Data Inputs are driven 0V to 5V. One output @ GND. Note 7: Max number of Data Inputs (n) switching. n−1 Inputs switching 0V to 5V . Input-under-test switching: 5V to threshold (VILD), 0V to threshold (VIHD), f = 1 MHz. 3 www.fairchildsemi.com 74ACQ241 DC Electrical Characteristics 74ACQ241 AC Electrical Characteristics Symbol Parameter VCC TA = +25°C TA = −40°C to +85°C (V) CL = 50 pF CL = 50 pF (Note 8) Min Typ Max Min tPHL Propagation Delay 3.3 2.0 6.5 9.0 2.0 9.5 tPLH Data to Output 5.0 1.5 4.5 6.0 1.5 6.5 tPZL Output Enable Time 3.3 2.5 8.0 13.0 2.5 13.5 5.0 1.5 5.5 8.5 1.5 9.0 3.3 1.0 8.5 14.5 1.0 15.0 5.0 1.0 5.5 9.5 1.0 10.0 1.0 1.5 tPZH tPHZ Output Disable Time tPLZ tOSHL tOSLH Output to Output Skew Data to Output (Note 9) 3.3 Units Max 1.5 ns ns ns ns Note 8: Voltage Range 5.0 is 5.0V ±0.5V. Voltage Range 3.3 is 3.3V ±0.3V. Note 9: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH to LOW (tOSHL) or LOW to HIGH (tOSLH). Parameter guaranteed by design. Capacitance Typ Units CIN Symbol Input Capacitance Parameter 4.5 pF VCC = OPEN CPD Power Dissipation Capacitance 70 pF VCC = 5.0V www.fairchildsemi.com 4 Conditions The setup of a noise characteristics measurement is critical to the accuracy and repeatability of the tests. The following is a brief description of the setup used to measure the noise characteristics of FACT. VOLP/VOLV and VOHP/VOHV: • Determine the quiet output pin that demonstrates the greatest noise levels. The worst case pin will usually be the furthest from the ground pin. Monitor the output voltages using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. Equipment: Hewlett Packard Model 8180A Word Generator PC-163A Test Fixture • Measure VOLP and VOLV on the quiet output during the worst case transition for active and enable. Measure VOHP and VOHV on the quiet output during the worst case active and enable transition. Tektronics Model 7854 Oscilloscope Procedure: 1. Verify Test Fixture Loading: Standard Load 50 pF, 500Ω. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. VILD and VIHD: 2. Deskew the HFS generator so that no two channels have greater than 150 ps skew between them. This requires that the oscilloscope be deskewed first. It is important to deskew the HFS generator channels before testing. This will ensure that the outputs switch simultaneously. • Monitor one of the switching outputs using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. 3. Terminate all inputs and outputs to ensure proper loading of the outputs and that the input levels are at the correct voltage. • First increase the input LOW voltage level, VIL, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input LOW voltage level at which oscillation occurs is defined as VILD. 4. Set the HFS generator to toggle all but one output at a frequency of 1 MHz. Greater frequencies will increase DUT heating and effect the results of the measurement. 5. Set the word generator input levels at 0V LOW and 3V HIGH for ACT devices and 0V LOW and 5V HIGH for AC devices. Verify levels with an oscilloscope • Next decrease the input HIGH voltage level, VIH, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input HIGH voltage level at which oscillation occurs is defined as VIHD. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. FIGURE 1. Quiet Output Noise Voltage Waveforms Note 10: VOHV and VOLP are measured with respect to ground reference. Note 11: Input pulses have the following characteristics: f = 1 MHz, tr = 3 ns, tf = 3 ns, skew < 150 ps. FIGURE 2. Simultaneous Switching Test Circuit 5 www.fairchildsemi.com 74ACQ241 FACT Noise Characteristics 74ACQ241 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Small Outline Integrated Circuit, JEDEC MS-013, 0.300” Wide Body Package Number M20B www.fairchildsemi.com 6 20-Lead Plastic Dual-In-Line Package, JEDEC MS-001, 0.300” Wide Package Number N20A LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or systems device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the sonably expected to cause the failure of the life support body, or (b) support or sustain life, and (c) whose failure device or system, or to affect its safety or effectiveness. to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the www.fairchildsemi.com user. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. 74ACQ241 Octal Buffer/Line Driver with 3-STATE Outputs Physical Dimensions inches (millimeters) unless otherwise noted (Continued)