MN101C39C MN101C39C Type MN101CP39C Mask ROM Internal ROM type EPROM ROM (byte) 48K RAM (byte) 2K TQFP080-P-1212D 0.1 µs (at 4.5 V to 5.5 V, 20 MHz) 0.25 µs (at 2.7 V to 5.5 V, 8 MHz) 125 µs (at 2.0 V to 5.5 V, 32 kHz)* * The lower limit for operation guarantee for EPROM built-in type is 2.3 V. Package (Lead-free) Minimum Instruction Execution Time Interrupts RESET, Watchdog, External 0 to 4, Timer 2 to 5, Time base, Serial 0, Serial 1, A/D conversion finish Timer Counter Timer counter 2 : 8-bit × 1 (square-wave/8-bit PWM output, event count, synchronous output event) Clock source................ 1/1, 1/4 of system clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 2 Timer counter 3 : 8-bit × 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 16-bit × 1 (square-wave/16-bit PWM output, event count, synchronous output event, input capture) Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 4 Time base timer (one-minute count setting, independently operable 8-bit timer counter 5) Clock source................ 1/4 of system clock frequency; 1/1, 1/8192 of OSC oscillation clock frequency; 1/1, 1/8192 of XI oscillation clock frequency Interrupt source ........... coincidence with compare register 5; 1/8192 prescaler overflow Watchdog timer Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency (ROM option) Serial interface Serial 0 : synchronous type/simple UART (half-duplex) × 1 Clock source................ 1/2, 1/4, 1/16 of system clock frequency; 1/2 of timer counter 3 frequency Serial 1 : synchronous type × 1 Clock source................ 1/2, 1/8, 1/64 of system clock frequency; 1/2 of timer counter 3 frequency I/O Pins I/O 49 Input 12 Common use, Specified pull-up resistor available , Input/output selectable (bit unit) Specified pull-down resistor partially selectable Common use, Specified pull-up resistor available, Specified pull-down resistor partially selectable A/D converter 10-bit × 8-ch. (with S/H) Display control function LCD 28 segments × 4 commons (static , 1/2, 1/3, or 1/4 duty) Special Ports Buzzer output, remote control carrier signal output, high-current drive port MAD00015FEM MN101C39C Electrical Charactreistics (Supply current) Parameter Symbol Operating supply current Supply current at HALT Supply current at STOP Limit Condition min max Unit IDD1 fosc = 8 MHz , VDD = 5 V 8 25 mA IDD2 fx = 32 kHz , VDD = 3 V 18 100 µA IDD3 fx = 32 kHz , VDD = 3 V , Ta = 25°C 3 IDD4 fx = 32 kHz , VDD = 3 V , Ta = –40°C to +85°C IDD5 8 µA 25 µA VDD = 5 V , Ta = 25°C 1 µA VDD = 5 V , Ta = –40°C to +85°C 20 µA Development tools In-circuit Emulator PX-ICE101C/D+PX-PRB101C39-TQFP080-P-1212 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 MN101C39C 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 COM3 COM2 COM1 COM0 VLC3 VLC2 VLC1 VDD OSC2 OSC1 VSS XI XO MMOD VREFAN0, PA0 AN1, PA1 AN2, PA2 AN3, PA3 AN4, PA4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P66, SEG19, A6 P67, SEG18, A7 P70, SEG17, A8 P71, SEG16, A9 P72, SEG15, A10 P73, SEG14, A11 P74, SEG13, A12 P75, SEG12, A13 P76, SEG11, A14 P77, SEG10, A15 P87, SEG9, D7 P86, SEG8, D6 P85, SEG7, D5 P84, SEG6, D4 P83, SEG5, D3 P82, SEG4, D2 P81, SEG3, D1 P80, SEG2, D0 SEG1 SEG0 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 P65, SEG20, A5 P64, SEG21, A4 P63, SEG22, A3 P62, SEG23, A2 P61, SEG24, A1 P60, SEG25, A0 P54, SEG26, LED4, A17 P53, SEG27, LED3, A16 P52, LED2, NCS P51, LED1, NRE P50, LED0, NWE P47, KEY7 P46, KEY6 P45, KEY5 P44, KEY4 P43, KEY3 P42, KEY2 P41, KEY1 P40, KEY0 P23, IRQ3 Pin Assignment TQFP080-P-1212D MAD00015FEM typ IRQ2, P22 SENS, IRQ1, P21 IRQ0, P20 TM4IO, P14 TM3IO, P13 TM2IO, P12 P11 RMOUT, P10 NRST, P27 NDK, BUZZER, P06 SBT1, P05 SBI1, P04 SBO1, P03 SBT0, P02 RXD, SBI0, P01 TXD, SBO0, P00 VREF+ AN7, PA7 AN6, PA6 AN5, PA5 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.