VISHAY SI9182DB

Si9181DB/Si9182DB
Vishay Siliconix
Si9181DB/Si9182DB Demonstration Board
FEATURES
D 2-V to 6-V Input Voltages Range
D Uses Low-ESR Ceramic Capacitors At The Input and Output
D Fast Load and Line Transient Response
– On Board Load Transient Response Test Circuit
D 100-mVrms Noise With Noise Bypass Capacitor
– Probe Clip Provision For Accurate Noise Measurement
D 1-mA Maximum Shutdown Current.
D Built In Short Circuit and Thermal Protection
D Out of Regulation Error Flag
D Fixed 1.5-V, 1.8-V, 2.0-V, 2.5-V, 2.8-V, 3.0-V 3.8-V, 5.0-V, Or Adjustable Voltage Versions Available
D Provision To Measure The Ground Current
D Si9181—Low 150-mV Dropout At 350-mA Load
– 500-mA Peak Current Capability
– TSSOP-8 Package With 833-mW Power Dissipation
D Si9182—Low 105 mV Dropout At 250-mA Load
– 500-mA Peak Current Capability
– Space Saving MSOP-8 Package With 666-mW Power Dissipation
DESCRIPTION
The Si9181DQ/Si9182DH are the extremely low drop CMOS
linear regulator ICs operating from 2-V to 6-V input. These
devices offer ultra-low ground current and low dropout to
extend the battery life in portable electronics.
The demo boards are designed to verify different features
easily and quickly. The input and output capacitors are
selected to meet the specified noise and transient
requirement. The device features the use of low ESR, low cost
multi-layer ceramic capacitors. The Si9181DB/Si9182DB are
provided with a MOSFET switch along with other components
to measure the load transient response. The slew-rate of the
switching load can be adjusted easily to simulate the actual
load conditions. Provisions are made to measure the ground
current and output noise accurately.
The demonstration board uses surface mount and
through-hole components and is fully assembled and tested
for quick evaluation. The test points are provided for the
closed-loop response measurement.
Included in this document are the Bill-Of-Materials,
Schematics, PCB Layout of the Demo Boards and actual
waveforms/graphs.
The demonstration board layout is available in Gerber file format. Please contact your Vishay Siliconix sales representative or
distributor for a copy.
ORDERING INFORMATION:
Document Number: 71306
26-Sep-00
Si9181DB-A/Si9182DB-A . . . . . . . . . . . .
Si9181DB-B/Si9182DB-B . . . . . . . . . . . .
Si9181DB-C/Si9182DB-C . . . . . . . . . . . .
Si9181DB-D/Si9182DB-D . . . . . . . . . . . .
Si9181DB-E/Si9182DB-E . . . . . . . . . . . .
Si9181DB-F/Si9182DB-F . . . . . . . . . . . . .
Si9181DB-G/Si9182DB-G . . . . . . . . . . . .
(Adjustable Output)
(2.0-VOUT)
(2.5-VOUT)
(3.0-VOUT)
(3.3-VOUT)
(5.0-VOUT)
(1.8-VOUT)
www.vishay.com
1
Si9181DB/Si9182DB
Vishay Siliconix
POWER UP CHECK LIST AND OPERATION
LOAD TRANSIENT RESPONSE
Visually inspect the PCB to be sure that all the components are
intact and no foreign substance is lying on the board.
The Si9181DB and Si9182DB are provided with additional
circuit to measure the load step response from 1 to 150 mA
with 2-mSec load rise/fall times. The load step and slew-rate
can be easily changed by selecting R4, R5, R7 and R8.
1
Insert jumper JP2 and remove jumper JP3.
2
Insert JP1 to EN position.
3
Load the output to the rated load current.
4
Increase the input from 0 V slowly, while monitoring the
output. Note the regulated output voltage.
5
Increase the input to 6 V and check the line regulation. Vary
the load from 0 to 350 mA (Si9181DB) and 0 to 250 mA
(Si9182DB) and check the load regulation.
6
Follow the “Typical Waveforms and Performance” to verify
the dropout, transient response ground current and output
noise.
Remove the external load from the output, insert the jumper
JP3 and apply 5-Vpk-pk/5-kHz square wave signal at P5
(TRAN). Remove the oscilloscope probe-cap and insert the
probe into the probe-clip. Set the oscilloscope to 10 mV/div
and 5-mSec/div. Refer to Figures 3 through 5 for typical load
transient waveform.
GROUND CURRENT
Remove the jumper JP2 and insert micro-ampere meter. Use
thick and short wires to connect the meter. Vary the load to
measure the ground current at all loads. (See Figure 2.)
DROPOUT VOLTAGE
The dropout voltage is defined as the input to output voltage
differential measured, when the output drops by 100 mV from
its normal value. The output voltage is nominal at VIN equal to
VOUT + 1. The dropout voltage is different at different output.
Plots in Figure 1 and Figure 3 show the typical dropouts
measured on bench at 25_C ambient temperature.
Dropout vs. VOUT
Ground Current Measurement
250
mA–meter
Dropout Voltage (mV)
200
VIN
VOUT
JP2
150
Si9181DB, IOUT = 350 mA
LOAD
100
GND
50
GND
Si9182DB, IOUT = 250 mA
Si9181DB/Si9182DB
0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VOUT (V)
FIGURE 1. Dropout Voltage Si9181DB/Si9182DB
www.vishay.com S FaxBack 408-970-5600
2
FIGURE 2. Ground Current Measurement
Document Number: 71306
26-Sep-00
Si9181DB/Si9182DB
Vishay Siliconix
TYPICAL WAVEFORMS
VOUT
10 mV/div
VOUT
10 mV/div
ILOAD
100 mA/div
ILOAD
100 mA/div
5.00 ms/div
VOUT = 3.3 V
COUT = 2.2 mF
ILOAD = 1 to 150 mA
trise = 2 msec
FIGURE 3. Load Transient Response-1 (Si9181DB)
5.00 ms/div
VOUT = 3.3 V
COUT = 2.2 mF
ILOAD = 150 to 1 mA
tfall = 2 msec
FIGURE 4. Load Transient Response-2 (Si9181DB)
VOUT
10 mV/div
VOUT
10 mV/div
ILOAD
100 mA/div
ILOAD
100 mA/div
5.00 ms/div
VOUT = 3.3 V
COUT = 2.2 mF
ILOAD = 1 to 150 mA
trise = 2 msec
FIGURE 5. Load Transient Response-1 (Si9182DB)
Document Number: 71306
26-Sep-00
5.00 ms/div
VOUT = 3.3 V
COUT = 2.2 mF
ILOAD = 150 to 1 mA
tfall = 2 msec
FIGURE 6. Load Transient Response-2 (Si9182DB)
www.vishay.com
3
Si9181DB/Si9182DB
Vishay Siliconix
SCHEMATIC, PCB LAYOUT AND BILL OF MATERIAL (SI9181)
Si9181 DEMO BOARD
JP1
EN
1
2
SD
3
U1
1
C2
0.1 mF
SD
8
P3
2
DELAY
ERROR
7
1
JP2
C3
0.1 mF
P1
CNOISE
1
3
GND SENSE/VADJ
2
4
1
VIN
2 V–6 V
VIN
VOUT
6
R3
1 MΩ
R2
ERROR
JP3
P4
5
1
VOUT
350 mA
Si9181 (TSSOP–8)
R5
R4
5, 6, 7, 8
C1
10 mF
10 V
C4
2.2 mF
R1
TJ1
R8
D1
560
LL4154
Q1
R7
Si4410DY
4
1, 2, 3
P5
TRANSIENT
1
1.30 kΩ
R6
100 kΩ
C5
0.01 mF
SQUAREWAVE
D=50%
5 V PK, 5 kHz
P2
P6
1
1
GND
GND
LDO
Version Output
A
R1
R2 R4
Adjustable 124 k TBD
R5
TBD
TBD
B
2.0 V
Open
0
13.5
2.0 k
C
2.5 V
Open
0
16.9
2.49 k
D
3.0 V
Open
0
20.0
3.01 k
E
3.3 V
Open
0
22.1
3.32 k
F
5.0 V
Open
0
33.5
4.99 k
G
1.8 V
Open
0
12.1
1.82 k
FIGURE 7. Demo Board—Si9181
www.vishay.com S FaxBack 408-970-5600
4
Document Number: 71306
26-Sep-00
Si9181DB/Si9182DB
Vishay Siliconix
FIGURE 8. Silk Screen—Si9181
FIGURE 9. Top Layer—Si9181
FIGURE 10. Bottom Layer—Si9181
Document Number: 71306
26-Sep-00
www.vishay.com
5
Si9181DB/Si9182DB
Vishay Siliconix
BILLĆOFĆMATERIALSĊSi9181
Item
Qty
Designator
Part Type
Description
Footprint
Vendor Part #
Manufacturer
1
1
R1
TBD*
RES, 1%, 1/8 W
2
1
R2
TBD*
RES, 1%, 1/8 W
0805
TBD
Vishay Dale
0805
CRCW08051004FRT1
3
1
R3
1M
Vishay Dale
RES, 1%, 1/8 W
0805
TBD
Vishay Dale
4
1
R4
5
1
R5
TBD*
RES, 1%, 1/4 W
1206
TBD
Vishay Dale
TBD*
RES, 1%, 1/8 W
0805
TBD
6
1
Vishay Dale
R6
100 k
RES, 1%, 1/8 W
0805
CRCW08051003FRT1
Vishay Dale
7
8
1
R7
1.30 k
RES, 1%, 1/8 W
0805
CRCW08051301FRT1
Vishay Dale
1
R8
560
RES, 1%, 1/8 W
0805
CRCW08055600FRT1
Vishay Dale
9
1
C1
10 mF
CAP, CER, X5R, 10 V, 10%
1210
GRM42-2 X5R 106K 10
Murata
10
2
C2, C3
0.1 mF
CAP, CER, X7R, 50 V, 10%
0805
VJ0805Y104KXAAT
Vishay Vitramon
11
1
C4
2.2 mF
CAP, CER, X5R, 6.3 V, 10%
0805
GRM40X5R225K6.3
Murata
12
1
C5
0.01 mF
CAP, CER, X7R, 50 V, 10%
0805
VJ0805Y102KXAAT
Vishay Vitramon
13
1
Q1
Si4410DY
n-MOSFET, 30 V
SO-8
Si4410DY
Vishay Siliconix
14
1
U1
Si9181
Power IC
TSSOP-8
Si9181
Vishay Siliconix
15
1
D1
LL4154
Diode, 35 V, 150 mA
MINIMELF
LL4154
VISHAY LITEON
16
1
TJ1
Test Jack
For 0.135’ Dia Probe
TJ
131-4244-00
17
1
JP1
Jumper
3-Pin Header
SIP3
Multi-Source
18
2
JP2, JP3
Jumper
2-Pin Header
SIP2
Multi-Source
19
6
P1 TO P6
Power, GND, TP
1-Pin Header
TP1
Multi-Source
Jensen
*Refer to Si9181 Schematic, Figure 7.
www.vishay.com S FaxBack 408-970-5600
6
Document Number: 71306
26-Sep-00
Si9181DB/Si9182DB
Vishay Siliconix
SCHEMATIC, PCB LAYOUT AND BILL OF MATERIAL (SI9182)
Si9182 DEMO BOARD
JP1
EN
1
2
SD
3
U1
1
C2
0.1 mF
SD
8
P3
2
DELAY
ERROR
7
1
JP2
C3
0.1 mF
P1
CNOISE
1
3
GND SENSE/VADJ
2
4
1
VIN
2 V–6 V
VIN
VOUT
6
R3
1 MΩ
R2
ERROR
JP3
P4
5
1
VOUT
250 mA
Si9182 (MSOP–8)
R5
R4
5, 6, 7, 8
C1
10 mF
10 V
C4
2.2 mF
R1
TJ1
P5
TRANSIENT
Q1
R7
Si4410DY
4
1, 2, 3
1
1.30 kΩ
R6
100 kΩ
C5
0.01 mF
SQUAREWAVE
D=50%
5 V PK, 5 kHz
P2
P6
1
1
GND
GND
LDO
Version Output
A
R1
R2 R4
Adjustable 124 k TBD
R5
TBD
TBD
B
2.0 V
Open
0
13.5
2.0 k
C
2.5 V
Open
0
16.9
2.49 k
D
3.0 V
Open
0
20.0
3.01 k
E
3.3 V
Open
0
22.1
3.32 k
F
5.0 V
Open
0
33.5
4.99 k
G
1.8 V
Open
0
12.1
1.82 k
FIGURE 11. Demo Board—Si9182
Document Number: 71306
26-Sep-00
www.vishay.com
7
Si9181DB/Si9182DB
Vishay Siliconix
BILLĆOFĆMATERIALSĊSi9182
Item
Qty
Designator
Part Type
Description
Footprint
Vendor Part #
Manufacturer
1
1
R1
TBD*
RES, 1%, 1/8 W
0805
TBD
Vishay Dale
2
1
R2
TBD*
RES, 1%, 1/8 W
0805
TBD
Vishay Dale
3
1
R3
1M
RES, 1%, 1/8 W
0805
CRCW08051005FRT1
Vishay Dale
4
1
R4
TBD*
RES, 1%, 1/4 W
1206
TBD
Vishay Dale
5
1
R5
TBD*
RES, 1%, 1/8 W
0805
TBD
Vishay Dale
6
1
R6
100 k
RES, 1%, 1/8 W
0805
CRCW08051003FRT1
Vishay Dale
7
1
R7
1.30 k
RES, 1%, 1/8 W
0805
CRCW08051301FRT1
Vishay Dale
8
1
C1
10 mF
CAP, CER, X5R, 10 V, 10%
1210
GRM42-2X5R106K10
Murata
9
2
C2, C3
0.1 mF
CAP, CER, X7R, 50 V, 10%
0805
VJ0805Y104KXAAT
Vishay Vitramon
10
1
C4
2.2 mF
CAP, CER, X5R, 6.3 V, 10%
0805
GRM40X5R225K6.3
Murata
11
1
C5
0.01 mF
CAP, CER, X7R, 50 V, 10%
0805
VJ0805Y102KXAAT
Vishay Vitramon
12
1
Q1
Si4410DY
n-MOSFET, 30 V
SO-8
Si4410DY
Vishay Siliconix
13
1
U1
Si9182
300 mA LDO
MSOP-8
Si9182
Vishay Siliconix
14
1
TJ1
Test Jack
For 0.135’ Dia Probe
TJ
131-4244-00
15
1
JP1
Jumper
3-Pin Header
SIP3
Multi-Source
16
2
JP2, JP3
Jumper
2-Pin Header
SIP2
Multi-Source
17
6
P1 to P6
Power, GND, TP
1-Pin Header
TP1
Multi-Source
Jensen
*Refer to Si9182 Schematic, Figure 11.
www.vishay.com S FaxBack 408-970-5600
8
Document Number: 71306
26-Sep-00
Si9181DB/Si9182DB
Vishay Siliconix
FIGURE 12. Silk Screen—Si9182
FIGURE 13. Top Layer—Si9182
FIGURE 14. Bottom Layer—Si9182
Document Number: 71306
26-Sep-00
www.vishay.com
9