AD ADSP-2141LKS-E1

a
R
DSP
ADSP-2141L
APPLICATIONS
Security Coprocessor for High Speed Networking Products (Routers, Switches, Hubs)
Cryptographic Core for Firewalls, Hardware Encryptors,
and More
Crypto Peripheral for Implementing Secure NIC Adapters (10/100 Ethernet, Token Ring, ISDN)
Secure Modem-on-a-Chip (V.34, ADSL)
SECURE KERNEL CONTROL
Tamper-Resistant Isolation of Cryptographic Functions
Enforces Security Perimeter Around Crypto Functions
and Crypto Storage Locations
Anticloning Protection
Secure Algorithm Download
SafeNet CGX LIBRARY
On-Chip SafeNet CGX Crypto Library with Flexible CGX
API
Includes Chained and Parallel Execution Commands
Such as Hash-and-Encrypt
Embodied as 32K Words (32K ⴛ 24) Kernel Program
Mask-Programmed into On-Chip ROM
On-Chip Protected 4K ⴛ 16 Security Scratchpad RAM
FEATURES
DES CRYPTO BLOCK
640 Mbps Sustained Performance—Single DES
214 Mbps Sustained Performance—Triple DES
Supports All Modes: ECB; CBC; 64-Bit OFB; and 1-, 8-,
64-Bit CFB. Includes Automatic Padding
Implements IPsec ESP Transforms Autonomously at
OC-3 (155 Mbps) Rates (3-DES, SHA-1)
RANDOM NUMBER GENERATOR
Hardware-Based Nondeterministic Random Number
Generator
Generates Internal Session Keys That Are Never
Exposed Outside of the SafeNet DSP
Redundant Fail-Safe Design
Up to 1.3 Mbits of Random Data Available per Second
HASH BLOCK
Hardware-Based SHA-1 and MD-5 Hashing
253 Mbps Sustained Performance—SHA-1
315 Mbps Sustained Performance—MD-5
Implements IPsec AH and HMAC Transforms
FUNCTIONAL BLOCK DIAGRAM
KERNEL
MODE
CONTROL
BUS_MODE
IDMA MODE
IDMA
BUS
INTERRUPTS
FLAGS
SPORT 0
SERIAL
PORTS
ADSP-218x
DSP CORE
KERNEL ROM
32K 3 24
PROG ROM
16K 3 24
PCI MODE
PROTECTED
KERNEL
RAM
(4K 3 16)
IDMA
INTERFACE
16
32
PCI OR
CARDBUS
INTERFACE
32
16OR
32-BIT
BUS
DMA-32
CONTROLLER
ENCRYPT
BLOCK
(DES, 3-DES)
HASH
BLOCK
(MD-5, SHA-1)
RNG
BLOCK
PUBLIC KEY
ACCELERATOR
BUS_MODE
EMI BUS
SPORT 1
DATA ROM
16K 3 16
16
INTERRUPT
CONTROLLER
TIMER
APPLICATION
REGISTERS
EXTERNAL
MEMORY
INTERFACE
26-BITS
ADDR
PF7/INT_H
LASER
VARIABLE
STORE
SERIAL
EEPROM
INTERFACE
BUS_SEL
32-BITS
DATA
RAM/ROM
SafeNet is a registered trademark of Information Resource Engineering (IRE).
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
ADSP-2141L
PUBLIC KEY ACCELERATOR
Accelerator for Math-Intensive Public Key Operations
Diffie-Hellman Negotiate: <29 ms (1024-Bit Modulus,
180-Bit Exponent)
RSA 1024-Bit Sign: <29 ms; RSA 1024-Bit Verify: 6 ms
DSA Sign: <39 ms; DSA Verify: <66 ms
KEY MANAGEMENT BLOCK
Laser-Programmed Unique Triple-DES Cryptovariable
Protects Off-Chip Storage
Support for Secure Storage of Both Secret Keys and
Public/Private Key Pairs
Trust-Model Rules Enforcement
Only Encrypted Keys May Be Exported Off the Chip
Internal Key Cache for 15 Keys—Can Be Expanded to
700 Keys On-Chip
Keys May Also Be Securely Stored Off-Chip, Allowing
Unlimited Storage
DSP CORE
40 MIPS Sustained Performance
Single-Cycle Instruction Execution
Single-Cycle Context Switch
Zero-Overhead Looping
Low Power Dissipation
16K Words (16K ⴛ 24) On-Chip Program RAM
16K Words (16K ⴛ 16) On-Chip Data RAM
64M Words Off-Chip Program and Data Memory
Programmable 16-Bit Interval Timer with Prescale
PCI BUS/CARDBUS INTERFACE
32-Bit 3.3 V Bus Interface
33 MHz or 40 MHz* Bus Speed
Bus Master and Target Modes
Can Directly DMA Between Crypto Functions and Other
PCI Bus Agents
*66 MHz speed pending chip characterization.
GENERAL DESCRIPTION
The ADSP-2141L SafeNet DSP is a highly integrated embedded
security processor that incorporates a sophisticated, general
purpose DSP, along with a number of high performance Cryptographic function blocks, as well as PCI, DMA and Serial
EEPROM interfaces. It is fabricated in 0.35 µ CMOS triplelayer metal technology and uses a 3.3 V power supply. It is
available in a 208-lead MQFP package with a commercial (0°C
to 70°C) temperature range.
DSP Core
The DSP is a standard Analog Devices ADSP-218x core with
full ADSP-2100 family compatibility. The ADSP-218x Core
combines the base DSP components from the ADSP-2100
family with the addition of two serial ports, a 16-bit internal
DMA port, a byte DMA port, a programmable timer, Flag I/O,
extensive interrupt capabilities, and on-chip program and data
memory. The external memory interface of the 218x core has
been extended to support up to 64M-words addressing for both
program and data memory. Some core enhancements have been
added in the ADSP-2141L, including on-chip security ROM
and interrupt functions. Refer to the Analog Devices ADSP-2183
data sheet for further information.
SafeNet CGX Library–Secure Kernel
The SafeNet CGX Library is a crypto library embodied as firmware (a secure kernel) that is mask-programmed into ROM within
the DSP. This solution protects the library from tampering. The
CGX Library provides the Application Programming Interface
(API) to applications that require security services from the
ADSP-2141L. Those applications may be software executing in
user mode on the DSP, or they may be external host software
accessing the ADSP-2141L via a PCI bus. Approximately 40
Crypto commands—called CGX (CryptoGraphic eXtensions)—
are provided at the API and a simple control block structure is
used to pass arguments into the secure kernel and return status.
The CGX library includes integrated drivers for the various
hardware crypto blocks on the chip. This allows the programmer to ignore those details and concentrate on other product
design issues.
The CGX library firmware runs under a protected mode state
of the DSP as described in the Kernel Mode Control section
following. This guarantees the security integrity of the system
during the execution of CGX processes and, for example, prevents
disclosure of cryptographic key data or tampering with a
security operation.
Kernel Mode Control
The Kernel Mode Control subsystem is responsible for enforcing
the security perimeter around the cryptographic functions of
the ADSP-2141L. The device may operate in either user mode
(kernel space is not accessible) or kernel mode (kernel space is
accessible) at a given time. When in kernel mode, the kernel RAM
and certain protected crypto registers and functions (kernel
space) are accessible only to the CGX library firmware. The
CGX Library executes host-requested macro-level functions
and then returns control to the calling application. The kernel
mode control subsystem resets the DSP should any security
violation occur, such as attempting to access a protected
memory location while in user mode.
–2–
REV. 0
ADSP-2141L
PCI/Cardbus Interface
Protected Kernel RAM
The 4K × 16 kernel RAM provides a secure storage area on the
ADSP-2141L for sensitive data such as keys or intermediate
calculations during public key operations. The Kernel Mode
Control subsystem (above) enforces the protection by allowing
only internal secure kernel mode access to this RAM. A public
keyset and a cache of up to 15 secret keys may be stored in kernel
RAM. Secure key storage may be expanded to 700 secret keys
by assigning segments of the DSP’s internal data RAM to be
protected. Furthermore, a virtually unlimited number of data
encryption keys may be stored in an encrypted form in off-chip
memory.
A full 40 MHz/33 MHz PCI bus interface has been added to the
core DSP functions. The 32-bit PCI interface supports both bus
master and target modes. The ADSP-2141L is capable of using
DMA to directly access data on other PCI entities and pass that
data through its encryption/hash engines.
32-Bit DMA Controller
The ADSP-2141L incorporates a high performance 32-bit DMA
controller which can be set up to move data efficiently between
Host PCI memory, the hash/encrypt blocks, and/or external
memory. The DMA controller can be used with the PCI bus in
master mode, thus autonomously moving 32-bit data with minimal DSP intervention. Up to 255 long words (1020 bytes) can
be moved in a burst at up to 160 Mbytes per second.
Encrypt Block
The encrypt block performs high speed DES and Triple-DES
encrypt/decrypt operations. All four standard modes of DES are
supported: Electronic Code Book (ECB), Cipher Block Chaining
(CBC), 64-bit Output Feedback (OFB) and 1-bit, 8-bit and 64bit Cipher Feedback (CFB). The DES encrypt/decrypt operations
are highly pipelined and execute full 16-round DES in only four
clock cycles. Hardware support for padding insertion, verification
and removal further accelerates the encryption operation. Context switching is provided to minimize the overhead of changing
crypto keys and Initialization Vectors (IVs) to nearly zero.
Application Registers
The application registers are a set of memory-mapped registers
that facilitate communications between the ADSP-2141L and a
host processor via the PCI bus. One of the registers is a mailbox
that is 44 bytes long and set up to hold the CGX command
structure passed between the host and DSP processors. The
application registers also provide the mechanism that allows the
DSP and the external host to negotiate ownership of the hash/
encrypt block.
Hash Block
Serial EEPROM Interface
The secure hash block is tightly coupled with the encrypt block
and provides hardware accelerated one-way hash functions.
Both the MD-5 and SHA-1 algorithms are supported. Combined
operations that chain both hashing and encrypt/decrypt functions
are provided in order to significantly reduce the processing time
for data that needs both operations applied. For hash-then-encrypt
and hash-then-decrypt operations, the ADSP-2141L can perform
parallel execution of both functions from the same source and
destination buffers. For encrypt-then-hash and decrypt-then-hash
operations, the processing must be sequential, but minimum
latency is still provided through the pipeline chaining design. An
offset may be specified between the start of hashing and the
start of encryption to support certain protocols such as IPsec. A
‘mutable bit handler’ is also provided on the hash engine to
facilitate IPsec AH processing.
The serial EEPROM interface allows an external nonvolatile
memory to be connected to the ADSP-2141L for storing PCI
configuration information (Plug and Play), as well as generalpurpose nonvolatile storage. For example, encrypted (black)
keys could be stored into EEPROM for fast recovery after a
power outage.
Interrupt Controller
The DSP core provides support for 14 interrupt sources, including six external and eight internal. All interrupts are prioritized
into 12 levels and interrupt nesting may be enabled or disabled
under software control. The security block interrupt controller
provides enhancements to the DSP interrupt functions.
Primarily, the interrupt controller provides a new interrupt
generation capability to the DSP or to an external host processor.
Under programmable configuration control, a crypto interrupt
may be generated due to completion of certain operations such
as encrypt complete, hash complete. The interrupt may either
be directed at the DSP core (on IRQ2), or provided on an output line (PF7/INT_H) to a host subsystem.
Random Number Generator (RNG) Block
The hardware random number generator provides a true, nondeterministic noise source for the purpose of generating keys,
Initialization Vectors (IVs), and other random number requirements. Random numbers are provided as 16-bit words to the
kernel. The CGX kernel requests random numbers as needed to
perform requested CGX commands such as CGX_Gen_Key,
and can also directly supply from 1 to 65,535 random bytes to a
host application via the CGX_Random command.
Laser Variable Storage
The laser variable storage consists of 256 bits of tamper-proof
factory-programmed data that is only accessible to the internal
function blocks and the security kernel. Included in these laser
variable bits are:
• Local Storage Variable (master key-encryption key)
• Randomizer Seed (to supplement the true entropy fed into
the RNG)
• Program Control Data (enables/disables various features and
configures the ADSP-2141L)
• CRC of the Laser Data (to verify laser data integrity).
Public Key Accelerator
The public key accelerator module works in concert with the
CGX kernel firmware to provide full public key services to the
host application. The kernel provides macro-level functions to
perform Diffie-Hellman key agreement, RSA encrypt or decrypt,
DSA compute and verify digital signatures. The hardware accelerator block speeds computation-intensive operations such as
large vector multiply, add, subtract, square.
REV. 0
–3–
ADSP-2141L
The Program Control Data Bits (PCDBs) include configuration
for permitted key lengths, algorithm enables, Red KEK loading.
Most of the PCDB settings may be overridden with a digitally
signed token which may be loaded into the ADSP-2141L when
it boots. These tokens are created by IRE and each is targeted to
a specific ADSP-2141L using a hash of its unique identity.
Downloadable Secure Code
The ADSP-2141L allows additional security functions to be added
to the device through a secure download feature. Up to 16K
words of code may be downloaded into internal memory within
the DSP and this code can be given the security privileges of the
CGX kernel firmware. All downloaded firmware is authenticated
with a digital signature and verified with an on-chip public key.
Additional functions could include new encryption, hash or
public key algorithms such as IDEA, RC-4, RIPEMD, elliptic
curve, or any other application that needs direct control over the
protected cryptographic hardware.
0x3FFF
0x2000
8K KERNEL TOP
KERNEL MODE
(PMOVLAYL = C)
(PMOVLAYH = 000)
8K KERNEL BASE
KERNEL MODE
(PMOVLAYL = F)
(PMOVLAYH = 000)
ARCHITECTURE OVERVIEW
This section provides an architecture-level description of the
unique function blocks within the ADSP-2141L.
Memory Map
The ADSP-2141L memory map is very similar to that of the
ADSP-2183 DSP, except that it includes significantly more offchip memory addressing, and has additional crypto registers
which are accessible to the user.
DSP Core
The DSP core is architecturally identical to the ADSP-218x
with a few exceptions.
• The memory map includes additional external memory
addressing through the PMOVLAY and DMOVLAY mechanisms. For more information, see the Memory Map section.
• Additional memory-mapped crypto registers are available in
the kernel data RAM space.
• The PF7/INT_H flag pin may be reassigned to be the host
interrupt output.
8K INTERNAL
PAGE
(PMOVLAYL = 0)
(PMOVLAYH = 000)
8K EXTERNAL
PAGE = 0
(PMOVLAYL = 1)
(PMOVLAYH = 000)
0x1FFF
8K KERNEL
PAGE 8191
(PMOVLAYL = 2)
(PMOVLAYH = FFF)
UP TO 64 MEGAWORDS
EXTERNAL PROGRAM MEMORY
(PMOVLAYL ALTERNATES 2, 1, 2, 1...)
8K INTERNAL
(COMMON BANK)
PMOVLAYL = LS NIBBLE OF PMOVLAY
PMOVLAYH = MS 3 NIBBLES OF PMOVLAY
8K EXTERNAL
PAGE 1
(PMOVLAYL = 2)
(PMOVLAYH = 000)
0x0000
SHADED = KERNEL SPACE
Figure 1. Program Memory (MMAP = 0)
0x3FFF
0x2000
8K KERNEL TOP
KERNEL MODE
(PMOVLAYL = C)
(PMOVLAYH = 000)
8K KERNEL
KERNEL MODE
(PMOVLAYL = D)
(PMOVLAYH = 000)
8K KERNEL
KERNEL MODE
(PMOVLAYL = E)
(PMOVLAYH = 000)
8K KERNEL
KERNEL MODE
(PMOVLAYL = F)
(PMOVLAYH = 000)
8K INTERNAL
(PMOVLAYL = 0)
(PMOVLAYH = 000)
0x1FFF
PMOVLAYL = LS NIBBLE OF PMOVLAY
PMOVLAYH = MS 3 NIBBLES OF PMOVLAY
8K EXTERNAL
SHADED = KERNEL SPACE
0x0000
Figure 2. Program Memory (MMAP = 1)
0x3FFF
0x3FE0
0x3FDF
32
MEMORY-MAPPED
REGISTERS
UP TO 64 MEGAWORDS
EXTERNAL DATA MEMORY
(DMOVLAYL ALTERNATES 2, 1, 2, 1...)
8160 WORDS
INTERNAL
0x2000
0x1FFF
0x1800
0x17FF
0x1000
0x0FFF
0x0000
MEMORY-MAPPED
REGISTERS
8K INTERNAL
PROTECTED
(DMOVLAYL = 0)
4K KERNEL RAM (DMOVLAYH = 000)
(DMOVLAY = 000F)
KERNEL MODE
8K EXTERNAL
PAGE = 0
(DMOVLAYL = 1)
(DMOVLAYH = 000)
8K EXTERNAL
PAGE 1
(DMOVLAYL = 2)
(DMOVLAYH = 000)
8K KERNEL
PAGE 8191
(DMOVLAYL = 2)
(DMOVLAYH = FFF)
SHADED = KERNEL SPACE
Figure 3. Data Memory
–4–
REV. 0
ADSP-2141L
• IRQ2 now can include interrupt sources from the crypto
subsystem, depending on interrupt mask registers.
• A new read register has been added to indicate the state of
interrupt enable and interrupt masks.
• The kernel mode control subsystem has been added to supervise the protected mode of operation of the DSP core.
• Internal RAM protection logic has been added to allow the
kernel to seize increments of 1K word of internal PRAM and
DRAM.
• Bus mode configuration (218x vs. PCI) pins have been added.
• 32K words of kernel program ROM have been added to the
DSP memory space. (See the Memory Map section.)
set to 0x000F. Once in kernel mode, any branch to nonkernel
space program memory causes the DSP to return to user mode.
(Note: For security reasons when in kernel mode, the DSP does
not respond to Emulator bus requests.)
The kernel mode can be interrupted during execution; however,
during certain periods where sensitive data is being moved, all
interrupts are disabled. Within the interrupt service routine,
another call to the kernel (CGX call) may be made if desired,
although there are limitations on which CGX commands may
preempt another. (For information, see the ADSP-2141L CGX
Interface Programmer’s Guide http://www.ire-ma.com/proddoc.htm.)
Only one level of kernel mode nesting is permitted. An interrupt
to a user mode vector location while in nested kernel mode will
also trigger the violation reset logic.
Kernel Mode Control
The kernel mode control subsystem provides the following
functions which serve to enforce the security integrity of the
ADSP-2141L:
• Provide a means to securely enter the kernel mode.
• Provide a means to properly exit the kernel mode.
• Prevent user mode access to protected memory and register
locations.
• Manage interrupts during kernel mode executions.
• Manage the reset function to ensure that sensitive variables
in DSP registers are erased.
Once the interrupt service routine is finished, the return-frominterrupt must return control back to the kernel at the address/
overlay that was originally interrupted, otherwise the protection
logic will issue a chip reset.
Hash and Encrypt Block Overview
The encrypt block is tightly coupled to the hash block in the
ADSP-2141L and therefore the two are discussed together.
Refer to Figure 4, Hash/Encrypt Functional Block Diagram, for
the following description.
The algorithms implemented in the combined hash and encryption block are: DES, Triple DES, MD-5 and SHA-1. Data can
be transferred to and from the module once to perform both
hashing and encryption on the same data stream. The DES
encrypt/decrypt operations are highly paralleled and pipelined,
and execute full 16-round DES in only four clock cycles. The
internal data flow and buffering allows parallel execution of
hashing and encryption where possible, and allows processing of
data concurrently with I/O of previous and subsequent blocks.
Most of the kernel mode control functions are implemented in
the hardware of the ADSP-2141L and are not directly visible to
nonkernel applications (user mode). Any attempt by a user
mode application program running on the DSP to access a
kernel space addresses (PRAM 0x2001 – 0x3FFF, PMOVLAY
000C – 000F; or DRAM 0x0000 – 0x17FF, DMOVLAY 000F)
results in an immediate chip reset and all sensitive registers and
memory locations are erased. Kernel mode may only be entered
via a call, jump or increment to address 0x2000 with PMOVLAY
REGISTER
ADDRESS
7
RD
WR
PAD
INSERTION
512-BIT
FIFO
PAD
CONSUME
AND VERIFY
DSP
OR
PCI
ENCRYPT/
DECRYPT
BLOCK
DSP
OR
PCI
WRITE
CONTEXT
READ
CONTEXT
CONTEXT
STORAGE (0/1)
16-/32-BIT
OUTPUT
BUS
512-BIT
FIFO
HASH
DIGEST
16-/32-BIT
INPUT
BUS
HASH
BLOCK
MUTABLE BIT
PROCESSING
PAD
INSERTION
(ENCRYPT-THEN-HASH)
(DECRYPT-THEN-HASH)
Figure 4. Hash/Encrypt Functional Block Diagram
REV. 0
–5–
ADSP-2141L
Context switching is optimized to minimize the overhead of
changing cryptographic keys to near zero.
The software interface to the module consists of a set of
memory-mapped registers, all of which are visible to the DSP and
most of which can be enabled for host access via the PCI bus. A
set of five, 16-bit registers define the operation to be performed,
the length of the data buffer to be processed, in bytes, the offset
between the start of hashing and encryption (or vice versa), and
the padding operation. If the data length is unknown at the time
the encrypt/decrypt operation is started, the data length register
may be set to zero, which specifies special handling. In this case,
data may be passed to the hash/encrypt block indefinitely until
the end of data is encountered. At that time, the operation is
terminated by writing a new control word to the hash/encrypt
control register (either to process the next packet or to invoke
the idle state if there is no further work to do). This will close
out the processing for the packet, including the addition of the
selected crypto padding.
A set of seven status registers provides information on when a
new operation can be started, when there is space available to
accept new data, when there is data available to be read out, and
the results from the padding operation.
Crypto Contexts
There are two sets of crypto-context registers. Each context
contains a DES or triple DES key, initialization vector, and
precomputed hashes (inner and outer) of the authentication key
for HMAC operations. The contexts also contain registers to
reload the byte count from a previous operation (which is part
of the hashing context), as well as an IV (also called salt) for
decrypting a black key, if necessary.
Once a crypto-context has been loaded and the operation
defined, data is processed by writing it to a data input FIFO. At
the I/O interface, data is always written to, or read from, the
same address. Internally, the hash and encryption functions
have separate 512-bit FIFOs, each with their own FIFO management pointers. Incoming data is automatically routed to one
or both of these FIFOs, depending on the operation in progress.
Output from the encryption block is read from the data output
FIFO. In encrypt-hash or decrypt-hash operations, the data is
also automatically passed to the hashing data input FIFO. Output
from the hash function is always read from the digest register of
the appropriate crypto-context.
The initialization vector to be used for a crypto operation can be
loaded as part of a crypto-context. When an operation is complete,
the same context will contain the resulting IV produced at the
end, which can be saved away and restored later to continue the
operation with more data.
In certain packet-based applications such as IPsec, a feature is
available that avoids the need for the control software to generate
and load random IVs for outgoing (encrypted) packets. Effectively, the IV register can be configured to be automatically
updated with new random numbers for each encrypted packet,
with almost no software intervention.
Padding
When the input data is not a multiple of eight bytes (a 64-bit
DES block), the encrypt module can be configured to automatically append pad bytes. There are several options for how the
padding is constructed, which are specified using the pad control
word of the operation description. Options include zero padding,
pad-length character padding (PKCS#7), incrementing count,
with trailing pad length and next header byte (for IPsec), or
fixed character padding. Note that for the IPsec and PKCS#7
pad protocols, there are cases where the padding not only fills
out the last 8-byte block, but also causes an additional 8-byte
block of padding to be added.
For the hash operations, padding is automatically added as
specified in the MD-5 and SHA-1 standards. When the hash
final command is issued indicating the last of the input data, the
algorithm-specified padding and data count bits are added to the
end of the hash input buffer prior to computing the hash.
Data Offsets
Certain security protocols, including IPsec, require portions of a
data packet to be hashed while the remainder of the data is both
hashed and encrypted. The ADSP-2141L supports this requirement through the OFFSET register, which allows specifying the
number of 32-bit dwords of offset between the hash and encrypt/
decrypt operations.
Black Key Loads
The cryptographic keys loaded as part of a crypto-context can
be stored off-chip in a black, or encrypted, form. If the appropriate control bit is set (HECNTL Bit 15), the DES or 3-DES key
will be decrypted immediately after it is written into the context
register. The hardware handles this decryption automatically.
The Key Encryption Key (KEK) that covers the black keys
is loaded in a dedicated write-only KEK register within the
ADSP-2141L. The IV for decrypting the black secret key is
called ‘salt’ and must be stored along with the black key (as part
of the context). Note that 3-DES CBC mode is used for protecting 3-DES black keys and single DES CBC is used for
single DES black keys.
When black keys are used, the key-decrypt operation adds a
6-cycle overhead (0.15 µs @ 40 MHz) for DES keys or 36-cycle
overhead (0.9 µs @ 40 MHz) for triple DES keys each time a
new crypto-context is loaded. (Note that if the same context is
used for more than one packet operation, the key decryption does
not need to be performed again.) Depending on the sequencing
of operations, this key decryption may in fact be hidden (from a
performance impact perspective) if other operations are underway.
This is because the black key decryption process only requires
that the DES hardware be available. For example, if the DSP is
reading the previous hash result from the output FIFO, the
black key decryption can be going on in parallel. Also note that
the data driver firmware does NOT have to wait for the key to
be decrypted before writing data to the input FIFO. The hardware automatically waits for the key to be decrypted before
beginning to process data for a given packet. So, with efficient
pipeline programming, it is possible to make the impact of black
key essentially zero.
The KEK for key decryption is loaded via the secure kernel
firmware using one of the CGX key manipulation commands.
(For more information, see the Command Summary section.)
This KEK is typically the same for all black keys, since it is usually
protecting local storage only. It is designated the DKEK in the
CGX API.
One of the laser-programmed configuration bits specifies whether
red (plaintext) keys are allowed to be loaded into the ADSP2141L from a host. If the AllowRedKeyLoad laser bit is not set,
keys may only be loaded in their black form. This is useful in
systems where export restrictions limit the key length that may
be used or where the external storage environment is untrusted.
–6–
REV. 0
ADSP-2141L
If the AllowRedKeyLoad bit is set, keys may be loaded either in
their black form, or in the red or unencrypted form. Note that
the laser configuration bit may be overridden with a signed
enabler token. (For more information, see the Laser Variable
Storage section.)
result, as well as specifying the length and operation type. Once
the operation type field is written, the processor polls the operation complete status while the calculation is carried out.
The PKAC utilizes the protected kernel RAM for input, output
and intermediate variable storage. It may only be accessed from
the secure kernel mode. Since public key computations typically
take many milliseconds to complete, they may be preempted
using a DSP interrupt.
Depending on the definition of the security module boundary in
a given application, FIPS 140-1 may require the use of black
keys to protect key material. In other words, if the security
boundary does not enclose the database where keys are stored,
those keys must be protected from compromise. Black key is a
satisfactory way to meet this FIPS requirement.
Most application interaction with the public key accelerator will
occur via the CGX software interface (see the Command Interface section). Both high level public key operations such as RSA
Sign or Create Diffie-Hellman Key, as well as primitive operations
such as Multiply Vector, Add Long Vector, etc., are presented
via the CGX interface.
Random Number Generator (RNG) Block
The random number generator is designed to provide highly
random, nondeterministic binary numbers at a high delivery rate
with little software intervention. The random numbers are accessible to the kernel firmware in a 16-bit register that may be read
by the DSP in kernel mode. Once the register is read, the RNG
immediately generates a new 16-bit value that is available within
12 microseconds.
PCI/Cardbus Interface
The ADSP-2141L appears as a target on the PCI Bus as a single
contiguous memory space of 128k bytes. In this memory space,
the host can access the following:
• The unprotected internal crypto registers of the ADSP-2141L
• IDMA access to the DSP’s internal program memory (PM)
and data memory (DM)
• Paged access to external memory connected to the
ADSP-2141L
• The Kernel RAM (KRAM) if it has been unprotected by an
extended mode program
All application-level access to random numbers should occur
through the Kernels CGX_RANDOM command (see the
Command Summary section).
The random number generator is designed using a “shot noise”
true entropy source which is sampled by the master 40 MHz
clock of the ADSP-2141L. The entropy source then feeds a
complex nonlinear combinatorial circuit that produces the final
RNG output based on the interaction of the entropy source and
the 40 MHz system clock. Over 200 stages of Linear Feedback
Shift Register (LFSR) are incorporated into the RNG design.
As a PCI Master, the ADSP-2141L can transfer data between:
• The unprotected internal crypto registers and FIFOs of the
ADSP-2141L and PCI Host memory
• External memory and PCI Host memory
In order to facilitate FIPS 140-1 compliance, an option may be
selected during CGX kernel initialization to enable an ANSI
X9.17 Annex C post-randomizer to be applied to the output of
the RNG. This randomizer applies the DES ECB algorithm
multiple times to further disperse and whiten the random source.
Although this is not necessary to ensure the quality of the random
numbers, it meets the criteria for a NIST-approved random number generation algorithm.
A 32-bit DMA engine within the ADSP-2141L facilitates these
transfers and permits full PCI bandwidth use.
Serial EEPROM Interface
The serial EEPROM interface allows the ADSP-2141L to automatically read the PCI configuration parameters at chip power-up.
IRE can provide the data content for the EEPROM to properly
set the chip device vendor ID, type and properties for full compliance with the PCI Plug and Play standards.
Public Key Accelerator (PKAC)
The public key arithmetic coprocessor (otherwise known as a
BigNum processor) is designed to support long vector calculations of the kind needed to perform RSA, Diffie-Hellman and
Elliptic Curve operations.
In addition to being used for storage of host bus parameters, any
extra space in the EEPROM may be accessed by the DSP, either
in user mode or kernel mode. Support for this function is not
included in the standard CGX command set. Refer to the
ADSP-2141 User’s Manual for the information on the data
contents of the EEPROM. Refer to http://www.analog.com/
industry/dsp/ire.html.
The PKAC can perform multiplication, squaring, addition and
subtraction on arbitrary length bit vectors. The CGX software is
responsible for setting the address register for the operands and
Table I. Interrupt Sources
Internal Interrupt Sources
Interrupt
External Interrupt Sources
Notes
Reset
or Power-Up (PUCR = 1)
Power-Down
SPORT0 Transmit
SPORT0 Receive
BDMA Interrupt
SPORT1 Transmit Mixed with IRQ1
SPORT1 Receive
Mixed with IRQ0
Timer
REV. 0
–7–
Interrupt
Notes
IRQ2
IRQL1
IRQL0
IRQE
IRQ1
IRQ0
Edge- or Level-Sensitive
Level-Sensitive
Level-Sensitive
Edge-Sensitive
Edge- or Level-Sensitive
Edge- or Level-Sensitive
ADSP-2141L
Interrupt Controller
• 48-Bit Program Control Data (enables/disables various features and configures the ADSP-2141L)
• CRC of the Laser Data (to verify integrity of the laser bits)
The DSP core of the ADSP-2141L provides a powerful set of
interrupt sources. A total of 14 interrupt sources are available,
although two pairs are multiplexed, yielding 12 simultaneous
sources. Refer to Table I.
The LSV is a unique triple DES master key-encrypting key that
allows the ADSP-2141L to securely store data (primarily other keys)
off-chip for later reloading. This is necessary if more storage space
is needed than is available with on-chip RAM, or if keys need to
be saved and restored after a power outage. Each ADSP-2141L
produced is programmed with a unique, randomly generated
local storage variable.
The ADSP-2141L enhances the existing interrupt controller
within the ADSP-218x DSP Core with some additional functions related to the crypto functional blocks and the external
host bus interfaces. Two additional interrupt controller subsystems have been added to the basic interrupt controller as
shown in Figure 5.
The internal seed variable is used to randomly initialize the
RNG circuits before the entropy is mixed in. Each ADSP-2141L
produced is programmed with a unique, randomly generated
internal seed variable which is loaded into the RNG at chip boot
time and cannot ever be read by software.
The DSP interrupt controller allows programming between one
and nine sources for the IRQ2 interrupt to the DSP. The
DIMASK register provides the mask to select which interrupt
source is enabled. A pair of status registers, DUMSTAT and
DMSTAT, allow the DSP firmware to read the status of any
interrupt source either before or after the mask is applied.
The 48 Program Control Data Bits (PCDBs) include configuration for permitted key lengths, algorithm enables, red KEK
loading, internal IC pulse timing characteristics. The PCDBs
provide configuration data that falls into three categories:
The host interrupt controller allows programming between one
and five sources for the PF7/INT_H interrupt output signal
(which may be connected to the interrupt input of the host
system). The HMASK register provides the mask to select which
interrupt source is enabled. A pair of status registers, HUMSTAT
and HMSTAT, allow the host firmware to read the status of any
interrupt source either before or after the mask is applied.
• Internal IC pulse-timing characteristics
• ADSP-2141L hardware version number field
• ADSP-2141L feature enables
The first two categories consist of data that cannot be altered
once the ADSP-2141L has been fabricated.
Laser Variable Storage
The laser variables are configured through 256 Fuses in the
ADSP-2141L, which are programmed during IC manufacture.
Each ADSP-2141L produced is programmed with a unique set
of Laser Variables.
The feature enables can be overridden using a factory token
enabler which may be passed to the CGX kernel as part of the
CGX_INIT command. This token is digitally signed with an
IRE private key and verified internal to the ADSP-2141L with
its public key. The CGX_INIT command is documented in the
ADSP-2141 CGX Interface Programmer’s Guide (available from
http://www.ire-ma.com/proddoc.htm).
• Local Storage Variable (LSV—the Master Key-Encryption-Key)
• Internal Seed Variable
DSP
IMASK
IFC
IRQ2
EXTERNAL
INTERRUPTS
IRQE
IRQL0
IRQL1
IRQ0
IRQ1
IRQ2
HICFG
HICLR
DIFRC
HIFRC
DIMASK
HIMASK
HOST
INTERRUPT
H/E CONTEXT1
DONE
H/E CONTEXT0
DONE
HOST
WROTE CMD
DMA xFER
DONE
DMA xFER
QUEUED
EXT MEM
CONFLICT
HASH/ENC
ERROR
DSP
INTERRUPT
H/E CONTEXT1
DONE
H/E CONTEXT0
DONE
DSP
WROTE
CMD
HASH/ENC
ERROR
HOST UNMASKED STATUS REGISTER
ICNTL
DICFG
DICLR
DSP UNMASKED STATUS REGISTER
RESET
POWER DOWN
SPORT0 Tx
SPORT0 Rx
BDMA INT
TIMER INT
SPORT1 Tx
SPORT1 Rx
ADSP-2183
INTERRUPT
CONTROLLER
DSP MASKED STATUS REGISTER
INTERNAL
INTERRUPTS
HOST INTERRUPT CONTROLLER
HOST MASKED STATUS REGISTER
DSP INTERRUPT CONTROLLER
INTH
TO HOST
IRQ2
CRYPTO INTERRUPT
SUBSYSTEM BOUNDRY
Figure 5. Interrupt Controller Block Diagram
–8–
REV. 0
ADSP-2141L
PIN FUNCTIONS
I/O Descriptions
This section describes the physical I/O hardware on the ADSP-2141L.
PIN FUNCTION DESCRIPTIONS–I/O Hardware
Pin Name
# of
Pins
Input/
Output
Function
External Memory Bus
Address [25:0]
26
O
Data [31:0]
32
I/O
Interrupts
IRQ2
IRQL0
IRQL1
IRQE
1
1
1
1
I
I
I
I
Edge- or Level-Sensitive Interrupt Request
Level-Sensitive Interrupt Requests
Level-Sensitive Interrupt Requests
Edge-Sensitive Interrupt Request
Bus Signals
BR
BG
BGH
PMS
DMSL
DMSH
BMS
IOMS
CMS
RD
WR
1
1
1
1
1
1
1
1
1
1
1
I
O
O
O
O
O
O
O
O
O
O
Bus Request Input
Bus Grant Output
Bus Grant Hung Output
Program Memory Select Output
Data Memory Select Output (Lower 16 Bits for 32-Bit DM)
Upper Memory Select Output (Upper 16 Bits for 32-Bit DM, Not Used for 16-Bit DM)
Byte Memory Select Output
I/O Space Memory Select Output
Combined Memory Select Output (PMS, DMS*, IOMS, BMS)
Memory Read Enable Output
Memory Write Enable Output
Miscellaneous
MMAP
BMODE
CLKIN, XTAL
CLKOUT
1
1
2
1
I
I
I
O
Memory Map Select Input (1 = Overlay External at 0x0000)
Boot Option Control Input (0 = BDMA, 1 = IDMA)
Clock or Quartz Crystal Input (1/2 of the ADSP-2141 Clock)
Processor Clock Output
Serial Ports
SPORT0
SCLK0
DR0
RFS0
DT0
TFS0
1
1
1
1
1
I/O
I
I/O
O
I/O
Serial Port 0 Clock
Serial Port 0 Receive Data Input
Serial Port 0 Receive Frame Sync
Serial Port 0 Transmit Data Output
Serial Port 0 Transmit Frame Sync
SPORT1
Port Configuration
(System Control Reg) –>
SCLK1
DR1
RFS1
DT1
TFS1
1
1
1
1
1
I/O
I
I/O
O
I/O
1 = Serial Port
Serial Port 1
Serial Port 1 Receive Data Input
Serial Port 1 Receive Frame Sync
Serial Port 1 Transmit Data Output
Serial Port 1 Transmit Frame Sync
Power-Down
PWD
PWDACK
1
1
I
O
Power-Down Initiate Control
Power-Down Acknowledge
REV. 0
Address Output Pins for Program, Data, Byte and I/O Spaces (13 Bits 2183, 13 Bits
from Overlay Register) Note: A0 not used for 32-bit memory.
Data I/O Pins for Program and Data Memory Spaces
D31:0 are used for wide-bus data memory.
D23:0 are used for DSP Program RAM.
D23:8 are used for I/O Space.
D23:8 are used for DSP Data RAM.
D15:8 are used for byte memory.
D23:16 are also used as Byte Space Addresses
–9–
0 = Other
Clock
Flag In
IRQ0
Flag Out
IRQ1
ADSP-2141L
Pin Name
# of
Pins
Input/
Output
Function
Flags
PF6:0
PF7/INT_H
7
1
I/O
I/O
Programmable I/O Pins
Programmable I/O Pin–or–Interrupt Output (Host Mode)
Emulator
EE
EBR
EBG
ERESET
EMS
EINT
ECLK
ELIN
ELOUT
1
1
1
1
1
1
1
1
1
Serial EEPROM Interface
EE_DI
EE_DO
EE_CS
EE_SK
1
1
1
1
O
I
O
O
Serial EEPROM Data In
Serial EEPROM Data Out
Serial EEPROM Chip Select
Serial EEPROM Clock
Bus Select
BUS_MODE
BUS_SEL
1
1
I
I
Processor Bus Select
Bus Select
PCI Bus (Dedicated Pins)
PCI_CLK
PCI_PAR
PCI_IRDY
PCI_STOP
1
1
1
1
I
I/O
I/O
I/O
PCI Clock
PCI Parity Bit
PCI Initiator Ready
PCI Abort Transfer
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
(Emulator Only)
*When DMS is enabled for generation of CMS, the CMS is activated for DSP access to external memory only, NOT for DMA controller accesses.
Bus Mode Descriptions
The Pin Function Descriptions, Bus Mode table, shows the multiplexed pins in 2183 and PCI mode. For more information on the
PCI pins MPLX1–MPLX12, see the Pin Functions Description–PCI Mode Multiplex Bus table on the following page.
PIN FUNCTION DESCRIPTIONS—Bus Mode
Bus Mode
# of
Pins
Input/
Output
2183 Mode
(bus_mode = 0, bus_sel = 0)
PCI Mode
(bus_mode = 1, bus_sel = 0)
MPLX_RESET
MPLX1
MPLX2
MPLX3
MPLX4
MPLX5
MPLX6
MPLX7
MPLX8
MPLX9
MPLX10
MPLX11
MPLX12
MPLX_BUS[31:0]
1
1
1
1
1
1
1
1
1
1
1
1
1
32
I
I/O
I/O
I/O
I/O
I
I
I/O
I/O
I/O
I/O
I/O
O
I/O
RESET_1
Pci_rst
Pci_cbe3
Pci_cbe2
Pci_cbe1
Pci_cbe0
Pci_idsel
Pci_gnt
Pci_frame
Pci_devsel
Pci_trdy
Pci_perr
Pci_serr
Pci_req
Pci_ad15:0
Pci_ad31:16
Power
GND
VDD
Total:
24
22
208
–
Ground Pins
–
Power Supply Pins (3.3 V)
Includes the pins from this table and the I/O Hardware Pin Function Description table.
IRD
IWR
IS
IAL
IACK
FL0
FL1
FL2
IAD15:0
N/C 31:16
–10–
REV. 0
ADSP-2141L
IDMA Mode Multiplex Bus Pin Definition
IDMA Port (218x Mode)
PIN FUNCTION DESCRIPTIONS—IDMA Mode Multiplex Bus
Pin Name
IDMA Name
Pins
I/O
Description
MPLX5
MPLX6
MPLX7
MPLX8
MPLX9
MPLX10
MPLX11
MPLX12
MPLX_BUS
IRD
IWR
IS
IAL
IACK
FL0
FL1
FL2
IAD
1
1
1
1
1
1
1
1
16
I
I
I
I
O
O
O
O
I/O
IDMA Port Read Input
IDMA Port Write Input
IDMA Port Select
IDMA Port Address Latch
IDMA Port Access Ready Acknowledge
Output Flags
Output Flags
Output Flags
IDMA Data I/O
PCI Port
PIN FUNCTION DESCRIPTIONS—PCI Mode Multiplex Bus
Pin Name
PCI Name
Pins
I/O
Description
MPLX1
MPLX2
MPLX3
MPLX4
MPLX5
MPLX6
MPLX7
MPLX8
MPLX9
MPLX10
MPLX11
MPLX12
MPLX_BUS
Pci_cbe3
Pci_cbe2
Pci_cbe1
Pci_cbe0
Pci_idsel
Pci_gnt
Pci_frame
Pci_devsel
Pci_trdy
Pci_perr
Pci_serr
Pci_req
Pci_ad15:0
Pci_ad31:16
Pci_intA
1
1
1
1
1
1
1
1
1
1
1
1
I/O
I/O
I/O
I/O
I
I
I/O
I/O
I/O
I/O
I/O
O
Bus Command / Byte Enable 3
Bus Command / Byte Enable 2
Bus Command / Byte Enable 1
Bus Command / Byte Enable 0
Initialization Device Select
Bus Grant
Cycle Frame
Device Select
Target Ready
Parity Error
System Error
PCI Bus Request
32
1
I/O
O
PCI Address/Data Bus
PCI Interrupt A Request
PF7/INT_H
SYSTEM INTERFACE
The ADSP-2141L may be integrated into a wide variety of systems, including those that already have a microprocessor and
those that will use the ADSP-2141L as the main processor. The
device can be configured into one of two Host Bus modes:
IDMA or PCI.
IDMA Bus Mode
The IDMA bus mode operates the same as in a native ADSP218x device, as described in this section.
The IDMA port provides an efficient means of communication
between a host system and the ADSP-2141L. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memorymapped control registers.
The IDMA port has a 16-bit multiplexed address and data bus,
and supports reading or writing 16-bit data (DM) or 24-bit
program memory (PM). The IDMA port is completely asynchronous and can be written to while the ADSP-2141L is operating at full speed.
The DSP memory address is latched and then automatically
incremented after each IDMA transaction. An external device can
therefore access a block of sequentially addressed memory by
REV. 0
specifying only the starting address of the block. This increases
throughput as the address does not have to be sent for each
memory access.
The IDMA port access occurs in two phases. The first is the
IDMA address latch cycle. When the acknowledge is asserted, a
14-bit address and 1-bit destination type can be driven onto the
bus by an external device. The address specifies an on-chip
memory location; the destination type specifies whether it is a
DM or PM access. The falling edge of the address latch signal
latches this value to the IDMAA register.
Once the address is stored, data can either be read from or
written to the ADSP-2141L’s on-chip memory. Asserting the
select line (IS) and the appropriate read or write line (IRD and
IWR respectively) signals the ADSP-2141L that a particular
transaction is required. In either case, there is a one-processorcycle delay for synchronization. The memory access consumes
an additional processor cycle.
Once an access has occurred, the latched address is automatically incremented and another access can occur.
Through the IDMAA register, the ADSP-2141L can also
specify the starting address and data format for DMA operation.
Figure 6 illustrates a typical system configuration for the
IDMA mode.
–11–
ADSP-2141L
EXTERNAL
MEMORY BUS
ADSP-2141
CLKOUT
1/2X CLOCK
OR
CRYSTAL
32
DATA 31–0
CS
A10–0
ADDR
D23–8
DATA
IOMS
SPORT1
SPORT0
SCLK0
RFS0
TFS0
DT0
DR0
SERIAL
DEVICE
16
ADDR
D23–0
DATA
CMS
RESET
PCI_CLK
PCI_PAR
PCI_IRDY
PCI_STOP
A25–0*
(OPTIONAL)
D15–0
DATA
OVERLAY
MEMORY
D31–16
8192
8K 3 16
SEGMENTS
DMSH
DMSL
UP TO 32M 3 32
BR
BG
BGH
IAD15–0
MPLX31–16
PROGRAM
OVERLAY
MEMORY
8192
8K 3 24
PM SEGMENTS
PMS
IRD
IWR
IS
IAL
IACK
16
CS
16-BIT
I/O SPACE
2048
LOCATIONS
A25–0
IDMA PORT
SYSTEM
INTERFACE
OR
mCONTROLLER
BYTE
MEMORY
(BOOT
LOADER)
DATA
BMS
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
SERIAL
DEVICE
A0-A21
D15–8
IRQ2
IRQE
IRQL0
IRQL1
INTERRUPT
SOURCES
NC
A13–0
D23–16
CLKIN
XTAL
FL0–2
PF0–7
NC
26
ADDR25–0
BUS
ARBITER
PWD
PWDACK
BUS_MODE
BUS_SEL
VDD
MMAP
BMODE
EEPROM
EE_DI
EE_DO
EE_CS
EE_SK
VDD OR GND
NC
*ADDR0 FROM THE ADSP-2141
IS NO CONNECT FOR 32-BIT MEMORY.
ADSP-2141 ADDR1 IS WIRED TO RAM A0.
Figure 6. ADSP-2141L IDMA System Configuration
–12–
REV. 0
ADSP-2141L
PCI Bus Mode
Figure 7 illustrates a typical system configuration for the
PCI mode.
EXTERNAL
MEMORY BUS
ADSP-2141
CLKOUT
1/2X CLOCK
OR
CRYSTAL
26
A13–0
ADDR25-0
D23–16
CLKIN
XTAL
32
INTERRUPT
SOURCES
ADDR
D23–8
DATA
IOMS
SPORT1
SPORT0
SCLK0
RFS0
TFS0
DT0
DR0
SERIAL
DEVICE
4
PCI
BUS
32
INTA
PCI_AD31–0
PCI_RST
PCI_CLK
PCI_PAR
PCI_IRDY
PCI_STOP
PF7/INT_H
CS
16-BIT
I/O SPACE
2048
LOCATIONS
A25–0
ADDR
D23–0
DATA
PROGRAM
OVERLAY
MEMORY
8192
8K 3 24
PM SEGMENTS
PMS
CMS
A25–0*
(OPTIONAL)
D15–0
DATA
OVERLAY
MEMORY
D31–16
8192
8K 3 16
SEGMENTS
DMSH
DMSL
PCI PORT
PCI_CBE3-0
PCI_IDSEL
PCI_REQ
PCI_GNT
PCI_FRAME
PCI_DEVSEL
PCI_TRDY
PCI_PERR
PCI_SERR
CS
A10–0
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
SERIAL
DEVICE
DATA
BMS
IRQ2
IRQE
IRQL0
IRQL1
BYTE
MEMORY
(BOOT
LOADER)
D15–8
DATA 31-0
PF0–6
A0-A21
UP TO 32M 3 32
BR
BG
BGH
BUS
ARBITER
PWD
PWDACK
VDD
BUS_MODE
BUS_SEL
MMAP
BMODE
EEPROM
EE_DI
EE_DO
EE_CS
*ADDR0 FROM THE ADSP-2141
IS NO CONNECT FOR 32-BIT MEMORY.
ADSP-2141 ADDR1 IS WIRED TO RAM A0.
VDD OR GND
SERIAL
EEPROM
EE_SK
Figure 7. ADSP-2141L PCI System Configuration
REV. 0
–13–
ADSP-2141L
Table III. Boot Mode Selection
DEVICE OPERATION
OPERATIONAL MODES
Security Modes
The ADSP-2141L operates in one of two security modes: kernel
mode or user mode. The mode switching is performed on the fly
as program execution proceeds. Kernel mode is entered via a
jump or call to address 0x2000 with PMOVLAY set to 0x000F.
Kernel mode will exit on its own once it has completed a requested
operation (or terminates due to an error).
Special interrupt handling is performed if the DSP is executing
in kernel mode. While executing a CGX command in kernel
mode, it is possible to interrupt to a nonprotected vector location and then invoke the kernel again during the interrupt handler. The [IF CONDITION] RTI instruction must be used to
return to the kernel from the interrupt handler. The return
address and PMOVLAY page must match the interrupted address and PMOVLAY page. If not, the violation reset logic will
be triggered. Only one level of kernel mode nesting is permitted.
An interrupt to a nonprotected vector location while in nested
kernel mode will also trigger the violation reset logic.
While in kernel mode, it is possible to interrupt to a protected
vector location. In this case, the processor remains in kernel
mode. The [IF CONDITION] RTI instruction must be used to
return the processor from the interrupt handler. There is no
imposed limit on the number of nested interrupts to a protected
vector location.
The ADSP-2141L Host Bus may be configured for one of two
personalities: IDMA Mode or PCI Bus Mode. The selection of
mode is made with two hardware control inputs BUS_MODE
and BUS_SEL at boot time.
BUS_SEL
IDMA Mode
PCI Bus Mode
0
1
0
0
The ADSP-2141L may be bootstrap-loaded from one of three
sources: byte-wide memory, host processor bus, or external
program memory. The selection of mode is made with two
hardware control inputs BMODE and MMAP. When the host
processor boot mode is selected, any one of the two bus modes
may be used.
Byte-Wide (BDMA) Boot Mode
Host Bus (IDMA) Boot Mode
External Program Boot Mode
0
1
0
0
0
1
The hardware pin states are not relevant after the ADSP-2141L
comes out of power-up reset. Refer to the ADSP-2141L User’s
Manual (available from IRE) for information on BDMA, IDMA
and external program boot modes.
COMMAND INTERFACE
This section provides a general overview of the software command interface to the crypto functions in the ADSP-2141L.
Refer to the ADSP-2141 CGX Interface Programmer’s Guide
(available from http://www.ire-ma.com/proddoc.htm) for more
details.
Overview
The ADSP-2141L provides an embedded crypto library that
provides a command interface API (Application Programming
Interface) to outside applications. These commands are referred
to as CGX (CryptoGraphic eXtensions).
• Keys within the ADSP-2141L are marked with an attributes
field that specifies key type and trust level.
• A key’s type field must match the use in a requested operation (i.e., cannot use a KEK to encrypt traffic).
• Keys generated internal to the ADSP-2141L (i.e., from RNG)
are marked as trusted.
This selection may not be changed after the ADSP-2141L
comes out of power-up reset. It is typically expected that the bus
mode signals are tied to ground or VDD on the PC Board.
Boot Modes
MMAP
• Unencrypted (red) keys may never be retrieved from the
ADSP-2141L.
Table II. Bus Mode Selection
BUS_MODE
BMODE
The CGX API simultaneously enforces certain security policies
within the ADSP-2141L and insulates applications from the
details of many complex cryptographic operations. The security
policy built into the ADSP-2141L has some of the following
rules:
Bus Modes
Bus Mode Pins
Boot Mode Pins
• Keys that are negotiated or imported from outside systems are
marked untrusted (although they may still be quite secure).
• Separate trusted and untrusted key hierarchies may be maintained and customer applications may choose which trust
level is required for a given command.
For most key management operations, the CGX interface must
be used. However, for certain high performance encryption/
hashing applications, the CGX interface may be bypassed and
either the DSP or a host processor may exercise direct control
over the hash/encrypt block.
–14–
REV. 0
ADSP-2141L
COMMAND SUMMARY
Approximately 40 CGX Commands are supported in the API to the ADSP-2141L.
General Utilities
INIT
DEFAULT
RANDOM
GET CHIPINFO
SELF TEST
Initializes Secure Kernel and Allow Reconfiguration of the ADSP-2141L
Restores Factory Default Settings
Generates Random Numbers (between 1K and 64K bytes)
Returns ADSP-2141L System Information
Runs a suite of self-tests on the hardware and CGX
Symmetrical Key Management
UNCOVER KEY
GEN KEY
GEN KEK
GEN RKEK
SAVE KEY
LOAD KEY
DERIVE KEY
TRANSFORM KEY
DESTROY KEY
EXPORT KEY
IMPORT KEY
Loads and Decrypts a Secret Key
Generates a Secret Key
Generates an Internal Key Encryption Key
Generates a Key Recovery Key Encryption Key
Saves a key protected by the Recovery Key (RKEK)
Imports a Red (plaintext) User Secret Key
Derives a Secret Key from a Pass Phrase
Transforms a Secret Key using IPsec
Removes Secret Key from the KCR
Exports an IRE-format Secret Key
Imports an IRE-format Secret Key
Symmetrical Encryption
ENCRYPT
DECRYPT
LOAD KG
Encrypts Data
Decrypts Data
Loads Secret Key into HW/SW Key Generator
Hash
HASH INIT
HASH DATA
HASH ENCRYPT
HASH DECRYPT
Initializes the Hash Operator
Hash Customer Data
Hash and Encrypt Customer Data
Hash and Decrypt Customer Data
PRF Functions
MERGE KEY
MERGE LONG KEY
EXTRACT LONG KEY
PRF DATA
PRF KEY
Combines two secret keys into one key
Combines two secret keys into a data string (long key)
Creates a secret key from a data string (long key)
Hash multiple data items using HMAC
Completes the above HMAC and create secret key
Asymmetrical Key Management
GEN PUBKEY
GEN NEWPUBKEY
GEN NEGKEY
EXPORT PUBKEY
IMPORT PUBKEY
Generates a Public Keyset (Public and Private Parts)
Generates a part of a Public Keyset
Generates a Diffie-Hellman Derived Secret Key
Exports an IRE-format Public Key
Imports an IRE-format Public Key
Asymmetrical Encryption
PUBKEY ENCRYPT
PUBKEY DECRYPT
Encrypts Data using RSA Public Key
Decrypts Data using RSA Public Key
Digital Signatures
SIGN
VERIFY
Digitally Signs a Message
Verifies a Digital Signature
Math Utilities
ADD VECTOR
SUB VECTOR
MULT VECTOR
EXP VECTOR
SHIFT VECTOR
Performs a Vector Add Operation
Performs a Vector Subtract Operation
Performs a Vector Multiply Operation
Performs a Vector Exponentiate Operation
Performs a Vector Right or Left Shift Operation
Extended Mode
LOAD EXTENDED
EXECUTE EXTENDED
REV. 0
Loads/Enables Extended (Downloaded) Algorithm Block
Executes Extended (Downloaded) Algorithm Block
–15–
ADSP-2141L
ABSOLUTE MAXIMUM RATINGS
Frequency Dependency For Timing Specifications
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.6 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to VDD + 0.5 V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to VDD + 0.5 V
Operating Temperature Range (Ambient) . . . . . 0°C to 70°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 sec) MQFP . . . . . . . . . . . . . . . . . 280°C
tCK is defined as 0.5tCKI. The ADSP-2141L uses an input clock
with a frequency equal to half the instruction rate: a 20.0 MHz
input clock (which is equivalent to 50 ns) yields a 25 ns processor
cycle (equivalent to 40 MHz). tCK values within the range of 0.5tCKI
period should be substituted for all relevant timing parameters to
obtain the specification value.
Example: tCKH = 0.5tCK – 7 ns = 0.5 (25 ns) – 7 ns = 8 ns
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADSP-2141L features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–16–
WARNING!
ESD SENSITIVE DEVICE
REV. 0
ADSP-2141L
SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
K Grade
Parameter
VDD
TAMB
Supply Voltage
Ambient Operating Temperature
Min
Max
Unit
3.0
0
3.6
70
V
°C
Max
Unit
0.4
V
V
V
ELECTRICAL CHARACTERISTICS
DC SPECIFICATIONS
Parameter
VIH
VIH
VIL
VOH
Hi-Level Input Voltage1, 2
Hi-Level CLKIN/Reset Voltage
Lo-Level Input Voltage1, 3
Hi-Level Output Voltage1, 4, 5
VOL
Lo-Level Output Voltage1, 4, 5
IIH
Hi-Level Input Current3
IIL
Lo-Level Input Current3
IOZH
Three-State Leakage Current7
IOZL
Three-State Leakage Current9
IDD
Supply Current (Idle)10, 11
IDD
Supply Current (Dynamic)11, 13
CI
Input Pin Capacitance3, 6, 14
CO
Output Pin Capacitance6, 7, 14, 15
Test Conditions
Min
@ VDD = max
@ VDD = max
@ VDD = min
@ VDD = min
IOH = –0.5 mA
@ VDD = min
IOH = –100 µA6
@ VDD = min
IOL = 2 mA
@ VDD = max
VIN = VDD max
3 @ VDD = max
VIN = 0 V
@ VDD = max
VIN = VDD max8
@ VDD = max
VIN = 0 V9
@ VDD = 3.3
TAMB = 25°C
tCK = 25 ns12
tCK = 30 ns12
@ VDD = 3.3
TAMB = 25°C
tCK = 25 ns12
tCK = 30 ns12
@ VIN = 2.5 V
fIN = 1.0 MHz
TAMB = 25°C
@ VIN = 2.5 V
fIN = 1.0 MHz
TAMB = 25°C
2.0
2.4
K Grade
Typ
2.4
V
VDD – 0.3
V
0.4
V
10
µA
10
µA
10
µA
8
µA
16
15
mA
mA
195
165
mA
mA
8
pF
8
pF
NOTES
1
Bidirectional pins: D0–D31, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, IAD0–15, PF0–PF7.
2
Input only pins: IRQ2, BR, MMAP, BMODE, BUS MODE, BUS SEL, DR0, DR1, PWD, IRQL0, IRQL1, IRQE, IS, IRD, IWR, IAL.
3
Input only pins: CLKIN, RESET, IRQ2, BR, MMAP, BMODE, BUS MODE, BUS SEL, DR0, DR1, PWD, IRQL0, IRQL1, IRQE, IS, IRD, IWR, IAL.
4
Output pins: BG, BGH, PMS, DMSL, DMSH, BMS, IOMS, CMS, RD, WR, IACK, PWDACK, A0–A25, DT0, DT1, CLKOUT, FL2–0.
5
Although specified for TTL outputs, all ADSP-2141L outputs are CMOS-compatible and will drive to VDD and GND, assuming no dc loads.
6
Guaranteed but not tested.
7
Output pins: BG, BGH, PMS, DMSL, BMS, IOMS, DMSH, CMS, RD, WR, IACK, PWDACK, A0–A25, DT0, DT1, CLKOUT, FL2–0, EE_DI, EE_CS, EE_SK.
8
0 V on BR. CLKIN active (to force three-state condition).
9
Three-statable pins: A0–A25, D0–D31, PMS, DMSL, DMSH, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCKL0, SCLK1, TFS0, TFS1, RFS0, RFS1, IAD0–
IAD15, PF0–PF7.
10
Idle refers to ADSP-2141L state of operation during execution of IDLE Instruction. Deasserted pins are driven to either VDD or GND.
11
Current reflects device operating with no output loads.
12
VIN = 0.4 V and 2.4 V. For typical supply currents, refer to Power Dissipation section.
13
IDD measurement taken with 93% of instructions executing from internal memory and 7% from external memory. H/E operations are executing from internal
memory concurrently with PCI transactions. Initialization operations are executed from external memory.
14
Applies to MQFP package type.
15
Output pin capacitance is the capacitive load for any three-stated output pin.
Specifications subject to change without notice.
REV. 0
–17–
ADSP-2141L
DC SPECIFICATIONS– PCI Bus Pins
K Grade
Parameter
VIH
VIL
VOH
VOL
IIH
IIL
IOZH
IOZL
CI
CCLK
CIDSEL
LPIN
Test Conditions
1, 2
Hi-Level Input Voltage
Lo-Level Input Voltage1, 2
Hi-Level Output Voltage1, 3
Lo-Level Output Voltage1, 3
Hi-Level Input Current2
Lo-Level Input Current2
Three-State Leakage Current4
Three-State Leakage Current1
Input Pin Capacitance
PCI CLK Pin Capacitance
PCI IDSEL Pin Capacitance5
Pin Inductance
IOUT = –500 µA
IOUT = 1500 µA
0 < VIN < VDD
0 < VIN < VDD
0 < VIN < VDD
0 < VIN < VDD
TAMB = 25°C
TAMB = 25°C
TAMB = 25°C
Min
Max
Unit
0.5 VDD
–0.5
0.9 VDD
VDD + 0.5
0.3 VDD
V
V
V
V
µA
µA
µA
µA
pF
pF
pF
nH
0.1 VDD
10
10
10
10
10
12
8
20
5
NOTES
1
Bidirectional pins: MPLX_BUS [31:0}, MPLX1–4, MPLX7–10, MPLX12
2
Input only pins: MPLX_RESET, MPLX5, MPLX6, PCI_CLK, PCI_PAR, PCI_IRDY, PCI_STOP
3
Output only pins: MPLX11
4
Leakage currents include High-Z output leakage for bidirectional buffers with three-state outputs.
5
Lower capacitance of IDSEL (MPLX_5) input-only pin allows for nonresistive connection to Address/Data bus.
TIMING PARAMETERS
PCI Clock (Guaranteed Over Operating Temperature and Digital Supply Range)
The ADSP-2141L is targeted for use in PCI add-on I/O slave card designs. It provides a glueless interface to the PCI bus. All bus
drivers are compliant with PCI interface electrical switching and drive capability specifications.
The ADSP-2141L does not implement the following signals: LOCK, INTB, INTC, INTD, SBO, SDONE, CLKRUN, AD[64:32],
C/BE[7:4], REQ64, ACK64, PAR64.
Parameter
Min
Max
Unit
Timing Requirements:
tCYC
CLK Cycle Time
tHIGH
CLK High Time
tLOW
CLK Low Time
CLK Slew Rate1
RST Slew Rate2
25
11
11
1
50
100
ns
ns
ns
V/ns
mV/ns
4
NOTES
1
Rise and fall times are specified in terms of the edge rate measured in V/ns. This slew rate must be met across the minimum peak-to-peak portion of the waveform as
shown in Figure 8.
2
The minimum RST slew rate applies only to the rising (deassertion) edge of the reset signal, and ensures that system noise cannot render an otherwise monotonic
signal to appear to bounce in the switching range.
t CYC
t HIGH
0.6VCC
t LOW
0.5VCC
2V p-p
0.4VCC
(MINIMUM)
0.3VCC
0.2VCC
Figure 8. Clock Waveform
–18–
REV. 0
ADSP-2141L
Parameter
PCI Bus Interface
Timing Requirements:
CLK to Signal Valid
tVAL
tON
CLK to Low-Z Delay
tOFF
CLK to High-Z Delay
Input Setup to CLK
tSU
tH
Input Hold After CLK
tRST-OFF
RST Active to Outputs High-Z
CLK
Min
Max
Unit
2
2
11
ns
ns
ns
ns
ns
ns
28
7
1
40
VTEST
t VAL
OUTPUT
DELAY
VSTEP (3.3V SIGNALING)
OUTPUT CURRENT # LEAKAGE CURRENT
THREE-STATE
OUTPUT
t ON
t OFF
VTH
CLK
VTL
t SU
tH
VTH
INPUT
VTEST
INPUTS
VALID
VTEST
VTL
Figure 9. Output (Top) and Input Timing Measurement Conditions
REV. 0
–19–
VMAX
ADSP-2141L
Parameter
Min
Max
Unit
Clock Signals and Reset
Timing Requirements:
CLKIN Period
tCKI
tCKIL
CLKIN Width Low
tCKIH
CLKIN Width High
50
15
15
100
ns
ns
ns
Switching Characteristics:
tCKL
CLKOUT Width Low
tCKH
CLKOUT Width High
tCKOH
CLKIN High to CLKOUT High
0.5tCK – 7
0.5tCK – 7
0
Control Signals
Timing Requirement:
tRSP
RESET Width Low1
5tCK
20
ns
ns
ns
ns
NOTE
1
Applies after power-up sequence is complete. Internal phase lock loop requires no more than 2000 CLKIN cycles assuming stable CLKIN (not including crystal
oscillator start-up time).
t CKI
t CKIH
CLKIN
t CKIL
t CKOH
t CKH
CLKOUT
t CKL
Figure 10. Clock Signals and Reset
–20–
REV. 0
ADSP-2141L
Parameter
Min
Interrupts and Flags
Timing Requirements:
IRQx, FI, or PFx Setup Before CLKOUT Low1, 2, 3, 4
tIFS
tIFH
IRQx, FI, or PFx Hold After CLKOUT High1, 2, 3, 4
0.25tCK + 15
0.25tCK
Switching Characteristics:
tFOH
Flag Output Hold After CLKOUT Low5
tFOD
Flag Output Delay from CLKOUT Low5
Max
Unit
ns
ns
0.5tCK – 7
0.5tCK + 5
ns
ns
NOTES
1
If IRQx and FI inputs meet t IFS and tIFH setup/hold requirements, they will be recognized during the current clock cycle; otherwise the signals will be recognized on
the following cycle. (Refer to the Interrupt Controller Operation section in the Program Control chapter of the ADSP-2100 Family User’s Manual for further information on interrupt servicing.)
2
Edge-sensitive interrupts require pulsewidths greater than 10 ns; level-sensitive interrupts must be held low until serviced.
3
IRQx = IRQ0, IRQ1, IRQ2, IRQL0, IRQL1, IRQE.
4
PFx = PF0, PF1, PF2, PF3, PF4, PF5, PF6, PF7.
5
Flag Outputs = PFx, FL0, FL1, FL2, Flag_out.
tFOD
CLKOUT
tFOH
FLAG
OUTPUTS
t IFH
IRQx
FI
PFx
t IFS
Figure 11. Interrupts and Flags
REV. 0
–21–
ADSP-2141L
Parameter
Min
Bus Request/Bus Grant
Timing Requirements:
BR Hold After CLKOUT High1
tBH
tBS
BR Setup Before CLKOUT Low1
0.25tCK + 2
0.25tCK + 17
Switching Characteristics:
tSD
CLKOUT High to xMS, RD, WR Disable
xMS, RD, WR Disable to BG Low
tSDB
tSE
BG High to xMS, RD, WR Enable
tSEC
xMS, RD, WR Enable to CLKOUT High
xMS, RD, WR Disable to BGH Low2
tSDBH
tSEH
BGH High to xMS, RD, WR Enable2
0
0
0.25tCK – 6
0
0
Max
Unit
ns
ns
0.25tCK + 10 ns
ns
ns
ns
ns
ns
NOTES
xMS = PMS, DMSL, DMSH, CMS, IOMS, BMS.
1
BR is an asynchronous signal. If BR meets the setup/hold requirements, it will be recognized during the current clock cycle; otherwise, the signal will be recognized
on the following cycle. Refer to the ADSP-2100 Family User’s Manual for BR/BG cycle relationships.
2
BGH is asserted when the bus is granted and the processor requires control of the bus to continue.
t BH
CLKOUT
BR
t BS
CLKOUT
PMS, DMSL,
BMS, RD, WR
BG
BGH
t SD
t SEC
t SDB
t SE
t SDBH
t SEH
Figure 12. Bus Request/Bus Grant
–22–
REV. 0
ADSP-2141L
Parameter
Min
Max
Unit
External Memory Write: ADSP-2141L DMA Initiated
Switching Characteristics:
tA
Clock to Address and DMSx
tDW
Data Setup Before Write Deasserted
Data Hold After Write Deasserted
tDH
tWP
Write Pulsewidth
tWDE
Write Low to Data Enabled
Address, DMSx Setup Before Write Low
tASW
tDDR
Data Disable Before Write/Read Low
tCWR
Clock High to Write Low
Address, DMSx Setup Before Write High
tAW
tAH
Address and DMSx Hold After Clock
tWRA
Address, DMSx Hold After Write High
tWWR
Write High to Read/Write Low
5
0.5tCK – 2 + w
0.5tCK – 8
0.5tCK – 5 + w
–5
1
0
6
0.5tCK – 2 + w
2
0.5tCK – 7
0.5tCK – 3
9
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
12
1. If wait-state(s) added, then referenced to last wait-state clock interval.
2. w = DMA wait states × tCK.
25ns (REF @ 40MHz)
DSP CLOCK
OUT
t ASW
t AH
EXT. ADDR
(A25–0)
tA
t AW
t WRA
EXT. DMSH
EXT. DMSL
t CWR
t WP
t WWR
EXT. WR
t WDE
t DW
t DH
EXT. DATA
(D31–0)
Figure 13. External Memory Write: ADSP-2141L DMA Initiated
REV. 0
–23–
t DDR
ADSP-2141L
Parameter
Min
External Memory Read—ADSP-2141L DMA Initiated
Timing Requirements:
tRDD
Read Low to Data Valid
tAA
Address, DMSx Valid to Data Valid
Data Valid Before Read Deasserted
tSUR
tRDH
Data Hold After Read Deasserted
4
1
Switching Characteristics:
tA
Clock to Address and DMSx Active
Address, DMSx Setup Before Read Low
tASR
tAH
Address and DMSx Hold After Clock
tRDA
Address, DMSx Hold After Read High
Clock High to RD Low
tCRD
tRP
Read Pulsewidth
tRWR
RD High to Read or Write Low
5
2
2
0.5tCK – 7
8
0.5tCK – 5 + w
0.5tCK – 3
Max
Unit
0.5tCK – 8 + w
0.5tCK – 3 + w
ns
ns
ns
ns
9
ns
ns
ns
ns
ns
ns
ns
12
1. If wait-state(s) added, then referenced to last wait-state clock interval.
2. w = DMA wait states × tCK.
25ns (REF @ 40MHz)
DSP CLOCK
OUT
tA
t AH
EXT. ADDR
(A25–0)
t AA
t RDA
t ASR
EXT. DMSH
EXT. DMSL
t RWR
t RP
t CRD
EXT. RD
t RDD
t SUR
t RDH
EXT. DATA
(D31–0)
Figure 14. External Memory Read – ADSP-2141L DMA Initiated
–24–
REV. 0
ADSP-2141L
Parameter
Min
Max
Unit
External Memory Write: ADSP-2141L DSP Initiated
Switching Characteristics:
Clock to Address, xMS
tA
tDW
Data Setup Before Write Deasserted
tDH
Data Hold After Write Deasserted
Write Pulsewidth
tWP
tWDE
Write Low to Data Enabled
tASW
Address, xMS Setup Before Write Low
Data Disable Before Write/Read Low
tDDR
tCWR
Clock High to Write Low
tAW
Address, xMS Setup Before Write High
Address, xMS Hold After Clock
tAH
tWRA
Address, xMS Hold After Write High
tWWR
Write High to Read/Write Low
1
0.5tCK – 7 + w
0.25tCK – 3.5
0.5tCK – 5 + w
0
0.25tCK – 4
0.25tCK – 4
0.25tCK
0.75tCK – 6 + w
1
0.25tCK – 4
0.5tCK – 5
6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
0.5tCK + 9
1. If wait-state(s) added, then referenced to last wait-state clock interval.
2. w = DSP wait states × tCK .
25ns (REF @ 40MHz)
DSP CLOCK
OUT
t ASW
t AH
EXT. ADDR
(A13–0)
PMS, DMSx,
BMS, IOMS,
CMS
tA
t AW
t WP
t CWR
t WRA
t WWR
EXT. WR
t WDE
t DW
t DH
EXT. DATA
(D23–0)
Figure 15. External Memory Write: ADSP-2141L DSP Initiated
REV. 0
–25–
t DDR
ADSP-2141L
Parameter
Min
External Memory Read—ADSP-2141L DSP Initiated
Timing Requirements:
tRDD
Read Low to Data Valid
tAA
Address, xMS Valid to Data Valid
Data Valid Before Read Deasserted
tSUR
tRDH
Data Hold After Read Deasserted
9
0
Switching Characteristics:
tA
Clock to Address, xMS Active
Address, xMS Setup Before Read Low
tASR
tAH
Address, xMS Hold After Clock
tRDA
Address, xMS Hold After Read High
Clock High to RD Low
tCRD
tRP
Read Pulsewidth
tRWR
RD High to RD or WR Low
1
0.25tCK – 4
1
0.25tCK – 3
0.25tCK – 2
0.5tCK – 5 + w
0.5tCK –5
Max
Unit
0.5tCK – 10 + w
0.75tCK – 11.5 + w
ns
ns
ns
ns
6
ns
ns
ns
ns
ns
ns
ns
0.25tCK + 7
1. If wait-state(s) added, then referenced to last wait-state clock interval.
2. w = DSP wait state × tCK.
25ns (REF @ 40MHz)
DSP CLOCK
OUT
tA
t AH
EXT. ADDR
(A13–0)
t AA
t RDA
t ASR
PMS, DMSx,
BMS, IOMS,
CMS
t CRD
t RWR
t RP
EXT. RD
t RDD
t SUR
t RDH
EXT. DATA
(D23–0)
Figure 16. External Memory Read – ADSP-2141L DSP Initiated
–26–
REV. 0
ADSP-2141L
Parameter
Min
Serial Ports
Timing Requirements:
tSCK
SCLK Period
DR/TFS/RFS Setup Before SCLK Low
tSCS
tSCH
DR/TFS/RFS Hold After SCLK Low
tSCP
SCLKIN Width
50
4
7
15
Switching Characteristics:
tCC
CLKOUT High to SCLKOUT
tSCDE
SCLK High to DT Enable
tSCDV
SCLK High to DT Valid
TFS/RFSOUT Hold After SCLK High
tRH
tRD
TFS/RFSOUT Delay from SCLK High
tSCDH
DT Hold After SCLK High
TFS (Alt) to DT Enable
tTDE
tTDV
TFS (Alt) to DT Valid
tSCDD
SCLK High to DT Disable
tRDV
RFS (Multichannel, Frame Delay Zero) to DT Valid
CLKOUT
t CC
Max
ns
ns
ns
ns
0.25tCK
0
0.25tCK + 10
15
0
15
0
0
14
15
15
t CC
t SCK
SCLK
t SCS
t SCH
t SCP
DR
TFSIN
RFSIN
t RD
t RH
RFSOUT
TFSOUT
t SCDV
t SCDD
t SCDH
t SCDE
DT
t TDE
t TDV
TFSOUT
ALTERNATE
FRAME MODE
t RDV
RFSOUT
MULTICHANNEL MODE
FRAME DELAY 0
(MFD = 0)
t TDE
t TDV
TFSIN
ALTERNATE
FRAME MODE
t RDV
RFSIN
MULTICHANNEL MODE
FRAME DELAY 0
(MFD = 0)
Figure 17. Serial Ports
REV. 0
–27–
Unit
t SCP
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-2141L
Parameter
Min
IDMA Address Latch (IDMA Mode Multiplex Bus)
Timing Requirements:
tIALP
Duration of Address Latch1, 2
MPLX_BUS Address Setup Before Address Latch End2
tIASU
tIAH
MPLX_BUS Address Hold After Address Latch End2
tIKA
MPLX9 Low Before Start of Address Latch2, 3
tIALS
Start of Write or Read After Address Latch End2, 3
10
5
3
0
4
Max
Unit
ns
ns
ns
ns
ns
NOTES
1
Start of Address Latch = MPLX7 Low and MPLX8 High.
2
Start of Write or Read = MPLX7 Low and MPLX6 Low or MPLX5 Low.
3
End of Address Latch = MPLX7 High or MPLX8 Low.
/
MPLX9 IACK
t IKA
/
MPLX8 IAL
t IALP
/
MPLX7 IS
t IASU
t IAH
/
MPLX_BUS IAD15–0
t IALS
/
MPLX5 OR MPLX6 IRD OR IWR
Figure 18. IDMA Address Latch (IDMA Mode Multiplex Bus)
–28–
REV. 0
ADSP-2141L
Parameter
Min
IDMA Write, Short Write Cycle (IDMA Mode, Multiplex Bus)
Timing Requirements:
tIKW
MPLX9 Low Before Start of Write1
Duration of Write1, 2
tIWP
tIDSU
MPLX_BUS Data Setup Before End of Write2, 3, 4
tIDH
MPLX_BUS Hold After End of Write2, 3, 4
0
15
5
3
Switching Characteristic:
tIKHW
Start of Write to MPLX9 High
Max
ns
ns
ns
ns
15
NOTES
1
Start of Write = MPLX7 Low and MPLX6 Low.
2
End of Write = MPLX7 High or MPLX6 High.
3
If Write Pulse ends before MPLX9 Low, use specifications t IDSU, tIDH.
4
If Write Pulse ends after MPLX9 Low, use specifications t IKSU, tIKH.
t IKW
/
MPLX9 IACK
t IKHW
/
MPLX7 IS
t IWP
/
MPLX6 IWR
t IDH
t IDSU
/
MPLX_BUS IAD15–0
DATA
Figure 19. IDMA Write, Short Write Cycle (IDMA Mode, Multiplex Bus)
REV. 0
–29–
Unit
ns
ADSP-2141L
Parameter
Min
IDMA Write, Long Write Cycle (IDMA Mode, Multiplex Bus)
Timing Requirements:
tIKW
MPLX9 Low Before Start of Write1
MPLX_BUS Data Setup Before MPLX9 Low2, 3, 4
tIKSU
tIKH
MPLX_BUS Data Hold After MPLX9 Low2, 3, 4
0
0.5tCK + 10
2
Switching Characteristics:
tIKLW
Start of Write to MPLX9 Low4
tIKHW
Start of Write to MPLX9 High
Max
Unit
ns
ns
ns
1.5tCK
15
ns
ns
NOTES
1
Start of Write = MPLX7 Low and MPLX6 Low.
2
If Write Pulse ends before MPLX9 Low, use specifications t IDSU, tIDH.
3
If Write Pulse ends after MPLX9 Low, use specifications t IKSU, tIKH.
4
This is the earliest time for MPLX9 Low from Start of Write. For IDMA Write cycle relationships, please refer to the ADSP-2100 Family User’s Manual.
t IKW
/
MPLX9 IACK
t IKHW
t IKLW
/
MPLX7 IS
/
MPLX6 IWR
t IKH
t IKSU
/
MPLX_BUS IAD15–0
DATA
Figure 20. IDMA Write, Long Write Cycle (IDMA Mode, Multiplex Bus)
–30–
REV. 0
ADSP-2141L
Parameter
Min
IDMA Read, Long Read Cycle (IDMA Mode, Multiplex Bus)
Timing Requirements:
tIKR
MPLX9 Low Before Start of Read1
Duration of Read1
tIRP
0
15
Switching Characteristics:
tIKHR
MPLX9 High After Start of Read1
tIKDS
MPLX_BUS Data Setup Before MPLX9 Low
MPLX_BUS Data Hold After End of Read2
tIKDH
tIKDD
MPLX_BUS Data Disabled After End of Read2
tIRDE
MPLX_BUS Previous Data Enabled After Start of Read
MPLX_BUS Previous Data Valid After Start of Read
tIRDV
tIRDH1
MPLX_BUS Previous Data Hold After Start of Read (DM/PM1)3
tIRDH2
MPLX_BUS Previous Data Hold After Start of Read (PM2)4
Max
ns
ns
15
0.5tCK – 7
0
14
0
15
2tCK – 5
tCK – 5
NOTES
1
Start of Read = MPLX7 Low and MPLX5 Low.
2
End of Read = MPLX7 High or MPLX5 High.
3
DM read or first half of PM read.
4
Second half of PM read.
/
MPLX9 IACK
t IKHR
t IKR
/
MPLX7 IS
t IRP
/
MPLX6 IRD
t IRDE
t IKDH
t IKDS
PREVIOUS
DATA
/
MPLX_BUS IAD15–0
t IRDV
READ DATA
t IKDD
t IRDH
Figure 21. IDMA Read, Long Read Cycle (IDMA Mode, Multiplex Bus)
REV. 0
–31–
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-2141L
Parameter
Min
IDMA Read, Short Read Cycle (IDMA Mode, Multiplex Bus)
Timing Requirements:
MPLX9 Low Before Start of Read1
tIKR
tIRP
Duration of Read
0
15
Switching Characteristics:
tIKHR
MPLX9 High After Start of Read1
MPLX_BUS Data Hold After End of Read2
tIKDH
tIKDD
MPLX_BUS Data Disabled After End of Read2
tIRDE
MPLX_BUS Previous Data Enabled After Start of Read
tIRDV
MPLX_BUS Previous Data Valid After Start of Read
Max
Unit
ns
ns
15
0
14
0
15
ns
ns
ns
ns
ns
NOTES
1
Start of Read = MPLX7 Low and MPLX5 Low.
2
End of Read = MPLX7 High or MPLX5 High.
MPLX9/IACK
t IKR
t IKHR
MPLX7/IS
t IRP
MPLX6/IRD
t IRDE
t IKDH
PREVIOUS
DATA
MPLX_BUS/IAD15–0
t IRDV
t IKDD
Figure 22. IDMA Read, Short Read Cycle (IDMA Mode, Multiplex Bus)
–32–
REV. 0
ADSP-2141L
CAPACITIVE LOADING
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
Figures 23 and 24 show the capacitive loading characteristics of
the ADSP-2141L.
INPUT
OR
OUTPUT
18
T = +708C
VDD = 3.0V
RISE TIME (0.4V – 2.4V) – ns
16
1.5V
Figure 25. Voltage Reference Levels for AC Measurements (Except Output Enable/Disable)
14
12
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram. If multiple pins (such as
the data bus) are enabled, the measurement value is that of the
first pin to start driving.
10
8
6
4
2
0
1.5V
0
50
100
150
CL – pF
200
250
300
Figure 23. Typical Output Rise Time vs. Load Capacitance,
CL (at Maximum Ambient Operating Temperature)
REFERENCE
SIGNAL
tMEASURED
tENA
18
VOH
(MEASURED)
16
VALID OUTPUT DELAY
OR HOLD – ns
14
tDIS
OUTPUT
12
VOH
(MEASURED)
VOH (MEASURED) – 0.5V
2.0V
VOL (MEASURED) +0.5V
1.0V
VOL
(MEASURED)
10
VOL
(MEASURED)
tDECAY
8
OUTPUT STARTS
DRIVING
OUTPUT STOPS
DRIVING
6
4
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
2
NOMINAL
Figure 26. Output Enable/Disable
–2
–4
IOL
0
50
100
150
200
250
CL – pF
Figure 24. Typical Output Valid Delay or Hold vs. Load
Capacitance, CL (at Maximum Ambient Operating
Temperature)
TO
OUTPUT
PIN
+1.5V
50pF
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured
output high or low voltage to a high impedance state. The output disable time (tDIS) is the difference of tMEASURED and tDECAY,
as shown in the Output Enable/Disable diagram. The time is the
interval from when a reference signal reaches a high or low
voltage level to when the output voltages have changed by 0.5 V
from the measured output high or low voltage. The decay time,
tDECAY, is dependent on the capacitive load, CL, and the current
load, iL, on the output pin. It can be approximated by the following equation:
t DECAY =
CL • 0.5V
iL
from which
t DIS = t MEASURED – t DECAY
REV. 0
–33–
IOH
Figure 27. Equivalent Device Loading for AC Measurements (Including All Fixtures)
ADSP-2141L
Table IV. Thermal Ratings: MQFP Package
Rating Description
Symbol
Value (MQFP Still Air)
Value (MQFP 9500 fpm)
Thermal Resistance (Case to Ambient)
Thermal Resistance (Junction to Ambient)
Thermal Resistance (Junction to Case)
θCA
θJA
θJC
30.7°C/W
35°C/W
4.3°C/W
16.7°C/W
21°C/W
4.3°C/W
ENVIRONMENTAL CONDITIONS
POWER DISSIPATION
The following figures assume a four-layer JEDEC printed circuit
board:
Total power dissipation has two components: one due to internal circuitry and one due to the switching of external output
drivers. Internal power dissipation depends on the sequence in
which instructions execute and the data operands involved. See
IDDIN calculation in Electrical Characteristics section. Internal
power dissipation is calculated this way:
TAMB = TCASE – (PD × θCA)
TCASE = Case Temperature in °C
OUTPUT DRIVE CURRENTS
Figures 28 and 29 show typical I-V characteristics for the
output drivers of the ADSP-2141L. The curves represent the
current drive capability of the output drivers as a function of
output voltage.
–
–
–
–
100
VDD = 3.3V @ +258C
80
VDD = 3.6V @ 08C
SOURCE CURRENT – mA
60
PINT = IDDIN × VDD
The external component of total power dissipation is caused by
the switching of output pins. Its magnitude depends on:
the number of output pins that switch during each cycle (O)
the maximum frequency at which the pins can switch (f)
the load capacitance of the pins (C)
the voltage swing of the pins (VDD).
The external component is calculated using:
40
PEXT = O × C × VDD2 × f
20
The load capacitance should include the processor’s package
capacitance (CIN). The frequency f includes driving the load
high and then back low.
VDD = 3.0V @ +708C
0
VDD = 3.0V @ +708C
–20
VDD = 3.3V @ +258C
–40
VDD = 3.6V @ 08C
–60
–80
–100
0
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE – V
3.0
3.5
4.0
Figure 28. Typical Drive Currents (PCI Pins)
80
VDD = 3.3V @ +258C
60
SOURCE CURRENT – mA
VOH
40
20
VDD = 3.6V @ 08C
VDD = 3.0V @ +708C
0
VDD = 3.0V @ +708C
–20
VOL
VDD = 3.3V @ +258C
–40
–60
VDD = 3.6V @ 08C
–80
0
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE – V
3.0
3.5
4.0
Figure 29. Typical Drive Currents (Addr/Dbus/rd/wr Pins)
–34–
REV. 0
ADSP-2141L
Example:
POWER, INTERNAL
940
In an application where external data memory is used and no
other outputs are active, power dissipation is calculated as
follows:
Assumptions:
•
•
•
823mW
VDD = 3.6V
POWER (PINT) – mW
•
840
External data memory is accessed every cycle with 50% of the
address pins switching.
External data memory writes occur every other cycle with
50% of the data pins switching.
740
706mW
649mW
640
VDD = 3.3V
554mW
540
509mW
VDD = 3.0V
Each address and data pin has a 10 pF total load at the pin.
440
The application operates at VDD = 3.3 V and tCK = 25 ns.
431mW
Total Power Dissipation = PINT + (C × VDD2 × f )
PINT = internal power dissipation from Power vs. Frequency
graphs (Figures 30 and 31).
340
32
33
34
35
36
37
38
39
FREQUENCY – MHz
40
41
42
Figure 30. Power vs. Frequency
(C × VDD2 × f ) is calculated for each output:
POWER, IDLE
Address, DMS
Data Output, WR
RD
CLKOUT
8
9
1
1
× 10 pF
× 10 pF
× 10 pF
× 10 pF
80
× VDD2
×f
× 3.3 V
× 3.32 V
× 3.32 V
× 3.32 V
× 40 MHz
× 20 MHz
× 40 MHz
× 20 MHz
2
75
VDD = 3.6V
= 34.8 mW
= 19.6 mW
= 2.2 mW
= 4.4 mW
61.0 mW
74mW
70
POWER (PIDLE) – mW
# of
Pins × C
Total power dissipation for this example is PINT +61 mW.
68mW
65
60
55
50
45
41mW
40
32
VDD = 3.3V
53mW
VDD = 3.0V
43mW
51mW
33
34
35
36
37
38
39
FREQUENCY – MHz
40
Figure 31. Power vs. Frequency
REV. 0
–35–
41
42
ADSP-2141L
Pin Configurations
For all multiplexed pins the active sense is determined by the mode selected.
Pin # Pin Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
EMS
EE
GND
ECLK
ELOUT
ELIN
EINT
EBR
EBG
MMAP
BMODE
BUS_MODE
BUS_SEL
EE_SK
EE_CS
EE_DI
EE_DO
VDD
GND
PF[7]/INT_H
PF[6]
PF[5]
PF[4]
PF[3]
PF[2]
PF[1]
PF[0]
PWD
PWDACK
BR
BG
BGH
IRQE
IRQL0
IRQL1
IRQ2
VDD
GND
MPLX_RESET
MPLX12
MPLX_BUS[31]
VDD
Pin # Pin Name
Pin # Pin Name
Pin # Pin Name
Pin #
Pin Name
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
164
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
GND
DATA[0]
DATA[1]
DATA[2]
DATA[3]
VDD
GND
DATA[4]
DATA[5]
DATA[6]
DATA[7]
DATA[8]
DATA[9]
DATA[10]
DATA[11]
DATA[12]
DATA[13]
DATA[14]
DATA[15]
VDD
GND
DATA[16]
DATA[17]
DATA[18]
DATA[19]
DATA[20]
DATA[21]
VDD
GND
DATA[22]
DATA[23]
DATA[24]
DATA[25]
DATA[26]
DATA[27]
DATA[28]
DATA[29]
DATA[30]
DATA[31]
ERESET
PCI_CLK
GND
MPLX_BUS[30]
MPLX_BUS[29]
MPLX_BUS[28]
MPLX_BUS[27]
VDD
GND
MPLX_BUS[26]
MPLX_BUS[25]
MPLX_BUS[24]
MPLX1
MPLX_BUS[23]
MPLX_BUS[22]
VDD
GND
MPLX_BUS[21]
MPLX_BUS[20]
MPLX_BUS[19]
MPLX_BUS[18]
GND
VDD
VDD
GND
MPLX_BUS[17]
MPLX_BUS[16]
MPLX2
PCI_IRDY
VDD
GND
PCI_STOP
MPLX10
MPLX11
PCI_PAR
VDD
GND
MPLX3
MPLX7
MPLX9
MPLX8
GND
VDD
VDD
GND
MPLX6
MPLX5
MPLX_BUS[15]
MPLX_BUS[14]
MPLX_BUS[13]
MPLX_BUS[12]
VDD
GND
MPLX_BUS[11]
MPLX_BUS[10]
MPLX_BUS[9]
MPLX_BUS[8]
VDD
GND
MPLX4
MPLX_BUS[7]
MPLX_BUS[6]
MPLX_BUS[5]
MPLX_BUS[4]
VDD
GND
MPLX_BUS[3]
MPLX_BUS[2]
MPLX_BUS[1]
MPLX_BUS[0]
GND
CLKOUT
VDD
GND
WR
RD
DMSH
DMSL
PMS
BMS
CMS
IOMS
VDD
CLKIN
XTAL
–36–
GND
ADDR[0]
ADDR[1]
ADDR[2]
ADDR[3]
VDD
ADDR[4]
ADDR[5]
ADDR[6]
ADDR[7]
ADDR[8]
ADDR[9]
ADDR[10]
ADDR[11]
ADDR[12]
ADDR[13]
GND
ADDR[14]
ADDR[15]
ADDR[16]
ADDR[17]
ADDR[18]
ADDR[19]
VDD
ADDR[20]
ADDR[21]
ADDR[22]
ADDR[23]
ADDR[24]
ADDR[25]
DT0
TFS0
RFS0
DR0
SCLK0
DT1
TFS1
RFS1
DR1
SCLK1
GND
VDD
REV. 0
MPLX_BUS/Pci_ad[24]
MPLX1/Pci_cbe3
MPLX_BUS/Pci_ad[23]
MPLX_BUS/Pci_ad[22]
VDD
GND
MPLX_BUS/Pci_ad[21]
MPLX_BUS/Pci_ad[20]
MPLX_BUS/Pci_ad[20]
MPLX_BUS/Pci_ad[18]
GND
VDD
VDD
GND
MPLX_BUS/Pci_ad[17]
MPLX_BUS/Pci_ad[16]
MPLX2/Pci_cbe2
PCI_IRDY
VDD
GND
PCI_STOP
MPLX10/Pci_Perr
MPLX11/Pci_serr
PCI_PAR
VDD
GND
MPLX3/Pci_cbe1
MPLX7/Pci_frame
MPLX9/Pci_trdy
MPLX8/Pci_devsel
GND
VDD
VDD
GND
MPLX6/Pci_gnt
MPLX5/Pci_idsel
MPLX_BUS/Pci_ad[15]
MPLX_BUS/Pci_ad[14]
MPLX_BUS/Pci_ad[13]
MPLX_BUS/Pci_ad[12]
VDD
GND
MPLX_BUS/Pci_ad[11]
MPLX_BUS/Pci_ad[10]
MPLX_BUS/Pci_ad[9]
MPLX_BUS/Pci_ad[8]
VDD
GND
MPLX4/Pci_cbe0
MPLX_BUS/Pci_ad[7]
MPLX_BUS/Pci_ad[6]
MPLX_BUS/Pci_ad[5]
REV. 0
–37–
104
103
102
101
100
98
99
97
96
95
94
93
92
91
90
88
89
87
86
85
83
84
81
82
29
30
31
79
80
28
78
27
77
26
76
25
75
74
72
73
71
70
69
68
66
67
65
64
63
62
61
60
59
58
57
3
4
56
2
55
EMS
EE
GND
ECLK
ELOUT
ELIN
EINT
EBR
EBG
MMAP
BMODE
BUS_MODE
BUS_SEL
EE_SK
EE_CS
EE_DI
EE_DO
VDD
GND
PF[7]/INT_H
PF[6]
PF[5]
PF[4]
PF[3]
PF[2]
PF[1]
PF[0]
PWD
PWDACK
BR
BG
BGH
IRQE
IRQL0
IRQL1
IRQ2
VDD
GND
MPLX_RESET/Pci_rst
MPLX12/Pci_req
MPLX_BUS/Pci_ad[31]
VDD
PCI_CLK
GND
MPLX_BUS/Pci_ad[30]
MPLX_BUS/Pci_ad[29]
MPLX_BUS/Pci_ad[28]
MPLX_BUS/Pci_ad[27]
VDD
GND
MPLX_BUS/Pci_ad[26]
MPLX_BUS/Pci_ad[25]
54
53
158 TFS0
157 DT0
160 DR0
159 RFS0
162 DT1
161 SCLK0
164 RFS
163 1
TFS1
165 DR1
167 GND
166 SCLK1
169 GND
168 VDD
171 DATA[1]
170 DATA[0]
173 DATA[3]
172 DATA[2]
175 GND
174 VDD
177 DATA[5]
176 DATA[4]
178 DATA[6]
180 DATA[8]
179 DATA[7]
181 DATA[9]
183 DATA[11]
182 DATA[10]
185 DATA[13]
184 DATA[12]
187 DATA[15]
186 DATA[14]
189 GND
188 VDD
190 DATA[16]
191 DATA[17]
192 DATA[18]
193 DATA[19]
194 DATA[20]
196 VDD
195 DATA[21]
198 DATA[22]
197 GND
200 DATA[24]
199 DATA[23]
202 DATA[26]
201 DATA[25]
204 DATA[28]
203 DATA[27]
206 DATA[30]
205 DATA[29]
208 ERESET
207 DATA[31]
ADSP-2141L
PINOUT
PCI Mode
1
PIN 1
IDENTIFIER
156 ADDR[25]
155 ADDR[24]
154 ADDR[23]
5
6
153 ADDR[22]
152 ADDR[21]
7
10
8
151 ADDR[20]
150 VDD
149 ADDR[19]
9
148 ADDR[18]
147 ADDR[17]
11
12
13
146 ADDR[16]
145 ADDR[15]
14
15
144 ADDR[14]
143 GND
16
17
142 ADDR[13]
141 ADDR[12]
18
140 ADDR[11]
139 ADDR[10]
19
24
20
138 ADDR[9]
137 ADDR[8]
21
22
136 ADDR[7]
135 ADDR[6]
23
134 ADDR[5]
133 ADDR[4]
PCI MODE
ADSP-2141L
OO
132 VDD
131 ADDR[3]
TOP VIEW
(Not to Scale)
130 ADDR[2]
129 ADDR[1]
128 ADDR[0]
32
127 GND
126 XTAL
33
125 CLKIN
124 VDD
34
35
42
36
123 IOMS
122 CMS
121 BMS
37
38
120 PMS
119 DMSL
39
40
118 DMSH
117 RD
41
116 WR
115 GND
43
44
45
114 VDD
113 CLKOUT
46
47
112 GND
111 MPLX_BUS/Pci_ad[0]
110 MPLX_BUS/Pci_ad[1]
48
49
50
51
108 MPLX_BUS/Pci_ad[3]
107 GND
109 MPLX_BUS/Pci_ad[2]
52
105 MPLX_BUS/Pci_ad[4]
106 VDD
–38–
104
103
102
101
100
98
99
97
96
95
93
94
92
91
90
88
89
87
86
85
83
84
81
82
80
29
30
31
79
28
78
26
27
77
25
76
75
74
73
71
72
69
70
68
67
66
65
64
63
61
62
60
59
58
57
3
4
56
2
54
55
53
EMS
EE
GND
ECLK
ELOUT
ELIN
EINT
EBR
EBG
MMAP
BMODE
BUS_MODE
BUS_SEL
EE_SK
EE_CS
EE_DI
EE_DO
VDD
GND
PF[7]/INT_H
PF[6]
PF[5]
PF[4]
PF[3]
PF[2]
PF[1]
PF[0]
PWD
PWDACK
BR
BG
BGH
IRQE
IRQL0
IRQL1
IRQ2
VDD
GND
MPLX_RESET/RESET_1
MPLX12/FL2
MPLX_BUS/NC[31]
VDD
PCI_CLK
GND
MPLX_BUS/NC[30]
MPLX_BUS/NC[29]
MPLX_BUS/NC[28]
MPLX_BUS/NC[27]
VDD
GND
MPLX_BUS/NC[26]
MPLX_BUS/NC[25]
MPLX_BUS/NC[24]
MPLX1/NC
MPLX_BUS/NC[23]
MPLX_BUS/NC[22]
VDD
GND
MPLX_BUS/NC[21]
MPLX_BUS/NC[20]
MPLX_BUS/NC[19]
MPLX_BUS/NC[18]
GND
VDD
VDD
GND
MPLX_BUS/NC[17]
MPLX_BUS/NC[16]
MPLX2/NC
PCI_IRDY
VDD
GND
PCI_STOP
MPLX10/FL0
MPLX11/FL1
PCI_PAR
VDD
GND
MPLX3/NC
MPLX7/IS
MPLX9/IACK
MPLX8/IAL
GND
VDD
VDD
GND
MPLX6/IWR
MPLX5/IRD
MPLX_BUS/IAD[15]
MPLX_BUS/IAD[14]
MPLX_BUS/IAD[13]
MPLX_BUS/IAD[12]
VDD
GND
MPLX_BUS/IAD[11]
MPLX_BUS/IAD[10]
MPLX_BUS/IAD[9]
MPLX_BUS/IAD[8]
VDD
GND
MPLX4/NC
MPLX_BUS/IAD[7]
MPLX_BUS/IAD[6]
MPLX_BUS/IAD[5]
157 DT0
159 RFS0
158 TFS0
161 SCLK0
160 DR0
163 TFS1
162 DT1
165 DR1
164 RFS1
167 GND
166 SCLK1
169 GND
168 VDD
171 DATA[1]
170 DATA[0]
173 DATA[3]
172 DATA[2]
176 DATA[4]
175 GND
174 VDD
178 DATA[6]
177 DATA[5]
180 DATA[8]
179 DATA[7]
181 DATA[9]
183 DATA[11]
182 DATA[10]
185 DATA[13]
184 DATA[12]
187 DATA[15]
186 DATA[14]
188 VDD
189 GND
190 DATA[16]
191 DATA[17]
192 DATA[18]
193 DATA[19]
194 DATA[20]
196 VDD
195 DATA[21]
198 DATA[22]
197 GND
200 DATA[24]
199 DATA[23]
202 DATA[26]
201 DATA[25]
204 DATA[28]
203 DATA[27]
206 DATA[30]
205 DATA[29]
208 ERESET
207 DATA[31]
ADSP-2141L
PINOUT
2183-Mode
1
PIN 1
IDENTIFIER
156 ADDR[25]
155 ADDR[24]
5
6
153 ADDR[22]
152 ADDR[21]
154 ADDR[23]
7
8
151 ADDR[20]
150 VDD
9
149 ADDR[19]
148 ADDR[18]
10
147 ADDR[17]
11
12
13
146 ADDR[16]
145 ADDR[15]
14
15
144 ADDR[14]
143 GND
16
142 ADDR[13]
141 ADDR[12]
17
18
19
20
138 ADDR[9
]
137 ADDR[8]
140 ADDR[11
139 ]ADDR[10]
21
22
23
135 ADDR[6]
134 ADDR[5]
136 ADDR[7]
24
OO
ADSP-2141L
133 ADDR[4]
132 VDD
TOP VIEW
(Not to Scale)
2183 MODE
130 ADDR[2]
129 ADDR[1]
128 ADDR[0]
131 ADDR[3]
32
127 GND
126 XTAL
33
125 CLKIN
124 VDD
34
35
36
123 IOMS
122 CMS
37
121 BMS
120 PMS
38
39
40
119 DMSL
118 DMSH
41
117 RD
116 WR
42
43
44
115 GND
114 VDD
113 CLKOUT
46
45
112 GND
111 MPLX_BUS/IAD[0]
47
48
49
110 MPLX_BUS/IAD[1
]
109 MPLX_BUS/IAD[2]
50
108 MPLX_BUS/IAD[3]
107 GND
51
106 VDD
52
105 MPLX_BUS/IAD[4]
REV. 0
ADSP-2141L
PACKAGE DESCRIPTION
Package Details
The package shown below is a 208-lead metric quad flatpack. Measurements are listed in English and (metric). Because this package
is designed as a metric package, Analog Devices recommends that you use these measurements for any PCB layout.
C3654–5–1/00 (rev. 0)
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
208-Lead Metric Plastic Quad Flatpack (MQFP)
(Nonhermetic)
1.256 (31.40)
1.248 (31.20) SQ
1.240 (31.00)
0.164 (4.10)
MAX
0.041 (1.03)
0.035 (0.88)
0.031 (0.78)
SEATING
PLANE
10
TYP
208
157
1
156
1.124 (28.10)
1.120 (28.00) SQ
1.116 (27.90)
TOP VIEW
(PINS DOWN)
0.003 (0.08)
MAX LEAD
COPLANARITY
105
104
52
53
0.020 (0.50)
0.010 (0.25)
0.020 (0.50)
BSC
0.144 (3.59)
0.136 (3.39)
LEAD PITCH
0.011 (0.27)
0.009 (0.22)
0.007 (0.17)
LEAD WIDTH
NOTE:
THE ACTUAL POSITION OF EACH LEAD IS WITHIN 0.003 (0.08) FROM ITS IDEAL
POSITION WHEN MEASURED IN THE LATERAL DIRECTION.
CENTER FIGURES ARE TYPICAL UNLESS OTHERWISE NOTED.
THE 208 LEAD MQFP IS A METRIC PACKAGE. ENGLISH DIMENSIONS PROVIDED
ARE APPROXIMATE AND MUST NOT BE USED FOR BOARD DESIGN PURPOSES
Part Number
1
ADSP-2141LKS-N1
ADSP-2141LKS-E12
Ambient Temperature Range
Instruction Rate
Package Description
Package Option
0°C to +70°C
0°C to +70°C
40 MHz
40 MHz
208-Lead MQFP
208-Lead MQFP
S-208
S-208
NOTES
1
The ADSP-2141LKS-N1 is an electrically equivalent, full function, production (non x-grade) version of the product described in this data sheet. (Full function =
Triple DES enabled, full 168-bit key length, full 2048-bit public key lengths, red keys allowed.)
2
The ADSP-2141LKS-E1 is an electrically equivalent, full function, production (non x-grade) version of the product d escribed in this data sheet except for the following:
Encryption: DES only, with maximum 56-bit key length. Triple DES is disabled.
Public Key Algorithms: Public Key Algorithms limited to 1024-bit max modulus. Red keys not allowed in hardware crypto context.
REV. 0
–39–
PRINTED IN U.S.A.
ORDERING GUIDE