MAXIM MAX5180

19-1577; Rev 0; 10/99
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
The MAX5180/MAX5183 are designed to provide a high
level of signal integrity for the least amount of power dissipation. Both DACs operate from a single supply of
+2.7V to +3.3V. Additionally, these DACs have three
modes of operation: normal, low-power standby, and
complete shutdown, which provides the lowest possible
power dissipation with 1µA (max) shutdown current. A
fast wake-up time (0.5µs) from standby mode to full DAC
operation conserves power by activating the DACs only
when required.
The MAX5180/MAX5183 are packaged in a 28-pin QSOP
and are specified for the extended (-40°C to +85°C)
temperature range. For lower-resolution, dual 8-bit
versions, refer to the MAX5186/MAX5189 data sheet.
Features
♦ +2.7V to +3.3V Single-Supply Operation
♦ Wide Spurious-Free Dynamic Range: 70dB
at fOUT = 2.2MHz
♦ Fully Differential Outputs for Each DAC
♦ ±0.5% FSR Gain Mismatch
♦ ±0.2° Phase Mismatch
♦ Low-Current Standby or Full Shutdown Modes
♦ Internal +1.2V Low-Noise Bandgap Reference
♦ Small 28-Pin QSOP Package
Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
MAX5180BEEI
MAX5183BEEI
-40°C to +85°C
-40°C to +85°C
28 QSOP
28 QSOP
Pin Configuration
Applications
Signal Reconstruction of I and Q
Transmit Signals
TOP VIEW
CREF1 1
28 CREF2
Digital Signal Processing
OUT1P 2
27 OUT2P
Arbitrary Waveform Generation (AWG)
OUT1N 3
26 OUT2N
Imaging
AGND 4
25 REFO
AVDD 5
DACEN 6
24 REFR
MAX5180
MAX5183
23 DGND
PD 7
22 DVDD
CS 8
21 D9
CLK 9
20 D8
N.C. 10
19 D7
REN 11
18 D6
D0 12
17 D5
D1 13
16 D4
D2 14
15 D3
QSOP
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX5180/MAX5183
General Description
The MAX5180 contains two 10-bit, simultaneousupdate, current output digital-to-analog converters
(DACs) designed for superior performance in communications systems requiring analog signal reconstruction
with low distortion and low-power operation. The
MAX5183 provides equal specifications, with on-chip
precision resistors for voltage output operation. Both
devices are designed for 10pVs glitch operation to minimize unwanted spurious signal components at the output. An on-board +1.2V bandgap circuit provides a
well-regulated, low-noise reference that can be disabled for external reference operation.
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
ABSOLUTE MAXIMUM RATINGS
AVDD, DVDD to AGND, DGND .................................-0.3V to +6V
Digital Inputs to DGND.............................................-0.3V to +6V
OUT1P, OUT1N, OUT2P, OUT2N, CREF1,
CREF2 to AGND ...................................................-0.3V to +6V
VREF to AGND ..........................................................-0.3V to +6V
AGND to DGND.....................................................-0.3V to +0.3V
AVDD to DVDD .................................................................... ±3.3V
Maximum Current into Any Pin............................................50mA
Continuous Power Dissipation (TA = +70°C)
28-Pin QSOP (derate 9.00mW/°C above +70°C)....... 725mW
Operating Temperature Range
MAX518_BEEI.................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) ............................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(AVDD = DVDD = +3V ±10%, AGND = DGND = 0, fCLK = 40MHz, IFS = 1mA, 400Ω differential output, CL = 5pF, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
10
N
Integral Nonlinearity
INL
Differential Nonlinearity
DNL
Zero-Scale Error
Full-Scale Error
Bits
-2
±0.5
+2
LSB
Guaranteed monotonic
-1
±0.5
+1
LSB
MAX5180
-2
+2
MAX5183
-8
+8
(Note 1)
-40
±15
+40
LSB
LSB
DYNAMIC PERFORMANCE
Output Settling Time
To ±0.5LSB error band
Glitch Impulse
Spurious-Free Dynamic Range
to Nyquist
SFDR
fCLK = 40MHz
Total Harmonic Distortion to
Nyquist
THD
fCLK = 40MHz
Signal-to-Noise Ratio to Nyquist
SNR
fCLK = 40MHz
DAC-to-DAC Output Isolation
fOUT = 2.2MHz
Clock and Data Feedthrough
All 0s to all 1s
ns
10
pVs
72
fOUT = 550kHz
fOUT = 2.2MHz
25
57
fOUT = 550kHz
-70
fOUT = 2.2MHz
-68
fOUT = 550kHz
61
fOUT = 2.2MHz
59
56
Output Noise
dBc
70
-63
dB
dB
-60
dB
50
nVs
10
pA/√Hz
Gain Mismatch Between
DAC Outputs
fOUT = 2.2MHz
±0.5
Phase Mismatch Between
DAC Outputs
fOUT = 2.2MHz
±0.15
±1
%FSR
degrees
ANALOG OUTPUT
Full-Scale Output Voltage
400
VFS
Output Leakage Current
0.8
V
DACEN = 0, MAX5180 only
-1
1
µA
0.5
1.5
mA
Full-Scale Output Current
IFS
MAX5180 only
DAC External Output Resistor
Load
RL
MAX5180 only
2
mV
-0.3
Voltage Compliance of Output
1
400
_______________________________________________________________________________________
Ω
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
(AVDD = DVDD = +3V ±10%, AGND = DGND = 0, fCLK = 40MHz, IFS = 1mA, 400Ω differential output, CL = 5pF, TA = TMIN to TMAX,
unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
1.12
1.2
1.28
V
REFERENCE
Output Voltage Range
VREF
Output Voltage Temperature
Drift
TCVREF
50
ppm/°C
Reference Output Drive
Capability
IREFOUT
10
µA
Reference Supply Rejection
Current Gain (IFS / IREF)
0.5
mV/V
8
mA/mA
POWER REQUIREMENTS
Analog Power-Supply Voltage
2.7
AVDD
PD = 0, DACEN = 1, digital inputs at 0
or DVDD
2.7
3.3
V
5.0
mA
3.3
V
Analog Supply Current
IAVDD
Digital Power-Supply Voltage
DVDD
Digital Supply Current
IDVDD
PD = 0, DACEN = 1, digital inputs at 0
or DVDD
4.2
5.0
mA
ISTANDBY
PD = 0, DACEN = 0, digital inputs at 0
or DVDD
1.0
1.5
mA
ISHDN
PD = 1, DACEN = X, digital inputs at 0
or DVDD (X = don’t care)
0.5
1.0
µA
Standby Current
Shutdown Current
2.7
LOGIC INPUTS AND OUTPUTS
Digital Input Voltage High
VIH
Digital Input Voltage Low
VIL
Digital Input Current
IIN
Digital Input Capacitance
CIN
2
V
VIN = 0 or DVDD
10
0.8
V
±1
µA
pF
TIMING CHARACTERISTICS
DAC1 DATA to CLK Rise
Setup Time
tDS1
10
ns
DAC2 DATA to CLK Fall
Setup Time
tDS2
10
ns
DAC1 CLK Rise to DATA
Hold Time
tDH1
0
ns
DAC2 CLK Fall to DATA
Hold Time
tDH2
0
ns
CS Fall to CLK Rise Time
5
ns
CS Fall to CLK Fall Time
5
ns
DACEN Rise Time to VOUT_
0.5
µs
PD Fall Time to VOUT_
50
µs
Clock Period
tCP
25
ns
Clock High Time
tCH
10
ns
Clock Low Time
tCL
10
ns
_______________________________________________________________________________________
3
MAX5180/MAX5183
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(AVDD = DVDD = +3V, AGND = DGND = 0, 400Ω differential output, IFS = 1mA, CL = 5pF, TA = +25°C, unless otherwise noted.)
MAX5180/83-01
0.5
0.4
0.3
0.2
DNL (LSB)
0
0
-0.1
-0.1
-0.2
MAX5180
2.51
2.49
2.45
-0.3
0
INPUT CODE
INPUT CODE
ANALOG SUPPLY CURRENT vs. TEMPERATURE
DIGITAL SUPPLY CURRENT
vs. SUPPLY VOLTAGE
3.5
3.0
MAX5183
MAX5180
2.0
MAX5180
MAX5183
4
2
-15
10
35
60
3.0
3.5
4.0
4.5
5.0
590
580
MAX5183
570
MAX5183
580
570
MAX5180
560
550
4.0
4.5
SUPPLY VOLTAGE (V)
-40
-15
5.0
5.5
10
35
60
85
0.80
0.75
0.70
MAX5183
0.65
MAX5180
0.60
0.55
0.50
540
560
3.5
1
SHUTDOWN CURRENT vs. SUPPLY VOLTAGE
MAX5180/83-08
590
STANDBY CURRENT (µA)
MAX5180
3.0
MAX5180
2
TEMPERATURE (°C)
600
MAX5180/83-07
600
5.5
3
5.5
STANDBY CURRENT vs. TEMPERATURE
STANDBY CURRENT vs. SUPPLY VOLTAGE
2.5
MAX5183
4
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
610
5.0
0
2.5
85
SHUITDOWN CURRENT (µA)
-40
4.5
5
0
1.5
4.0
MAX5180/83-09
2.5
3.5
DIGITAL SUPPLY CURRENT
vs. TEMPERATURE
8
6
3.0
SUPPLY VOLTAGE (V)
10
DIGITAL SUPPLY CURRENT (mA)
MAX5180/83-04
4.0
2.5
128 256 384 512 640 768 896 1024
MAX5180/83-06
128 256 384 512 640 768 896 1024
DIGITAL SUPPLY CURRENT (mA)
0
4
MAX5183
2.47
-0.2
ANALOG SUPPLY CURRENT (mA)
0.1
MAX5180/83-05
INL (LSB)
0.3
0.1
2.53
SUPPLY CURRENT (mA)
0.4
0.2
2.55
MAX5180/83-02
0.6
ANALOG SUPPLY CURRENT
vs. SUPPLY VOLTAGE
DIFFERENTIAL NONLINEARITY vs. INPUT CODE
MAX5180/83-03
INTEGRAL NONLINEARITY vs. INPUT CODE
STANDBY CURRENT (µA)
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
0.45
-40
-15
10
35
TEMPERATURE (°C)
60
85
2.5
3.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
5.0
5.5
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
MAX5180
1.25
MAX5183
1.24
1.27
OUTPUT CURRENT (mA)
1.26
1.26
MAX5183
1.25
MAX5180
1.23
2.5
3.0
3.5
4.0
4.5
5.0
5.5
2
0
-40
-15
10
35
60
85
0
100
200
300
400
TEMPERATURE (°C)
REFERENCE CURRENT (µA)
DYNAMIC RESPONSE RISE TIME
DYNAMIC RESPONSE FALL TIME
SETTLING TIME
MAX5180/83-14
MAX5180/83-13
OUT_P
150mV/
div
OUT_P
150mV/
div
OUT_N
100mV/
div
OUT_N
150mV/
div
OUT_N
150mV/
div
OUT_P
100mV/
div
FFT PLOT, DAC2
MAX5180/83-16
0
-10
-20
-40
-50
-60
-40
-50
-60
-70
-70
-80
-80
-90
-90
-100
-110
-120
-100
-110
-120
6
8
10 12 14 16 18 20
FREQUENCY (MHz)
100
90
80
SFDR (dBc)
-30
(dBc)
-30
4
fOUT = 2.2MHz
fCLK = 40MHz
SPURIOUS-FREE DYNAMIC RANGE
vs. CLOCK FREQUENCY
MAX5180/83-18
FFT PLOT, DAC1
MAX5180/83-17
50ns/div
-20
2
12.5ns/div
50ns/div
fOUT = 2.2MHz
fCLK = 40MHz
500
MAX5180/83-15
SUPPLY VOLTAGE (V)
0
-10
0
3
1
1.24
1.23
(dBc)
4
MAX5180/83-11
MAX5180/83-10
1.27
OUTPUT CURRENT vs. REFERENCE CURRENT
1.28
REFERENCE VOLTAGE (V)
REFERENCE VOLTAGE (V)
1.28
INTERNAL REFERENCE VOLTAGE
vs. TEMPERATURE
MAX5180/83-12
INTERNAL REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
MAX5180/MAX5183
Typical Operating Characteristics (continued)
(AVDD = DVDD = +3V, AGND = DGND = 0, 400Ω differential output, IFS = 1mA, CL = 5pF, TA = +25°C, unless otherwise noted.)
DAC2
70
DAC1
60
50
40
0
2
4
6
8
10 12 14 16 18 20
FREQUENCY (MHz)
10 15 20 25 30 35 40 45 50 55 60
CLOCK FREQUENCY (MHz)
_______________________________________________________________________________________
5
Typical Operating Characteristics (continued)
(AVDD = DVDD = +3V, AGND = DGND = 0, 400Ω differential output, IFS = 1mA, CL = 5pF, TA = +25°C, unless otherwise noted.)
78
fCLK = 60MHz
76
fCLK = 40MHz
72
fCLK = 10MHz
70
fCLK = 50MHz
fCLK = 10MHz
68
DAC2
61.0
DAC1
60.5
68
fCLK = 30MHz
60.0
66
66
61.5
fCLK = 60MHz
fCLK = 30MHz
500 700 900 1100 1300 1500 1700 1900 2100 2300
500 700 900 1100 1300 1500 1700 1900 2100 2300
OUTPUT FREQUENCY (kHz)
OUTPUT FREQUENCY (kHz)
OUPUT FREQUENCY (kHz)
SPURIOUS-FREE DYNAMIC RANGE
vs. OUTPUT FREQUENCY
MULITONE SPURIOUS-FREE DYNAMIC RANGE
vs. OUTPUT FREQUENCY
SPURIOUS-FREE DYNAMIC RANGE
vs. FULL-SCALE OUTPUT CURRENT
-20
0
-80
-60
-120
-100
-140
-120
0
5
10
15
20
OUTPUT FREQUENCY (MHz)
25
30
2500
68
66
64
62
-140
-160
2000
70
-40
-80
-100
1500
72
SFDR (dBc)
SFDR (dBc)
-60
1000
74
-20
-40
500
MAX5180/83-24
0
0
MAX5180/83-23
20
MAX5180/83-22
20
6
62.0
SINAD (dB)
72
70
62.5
74
SFDR (dBc)
74
SFDR (dBc)
fCLK = 20MHz
fCLK = 50MHz fCLK = 20MHz fCLK = 40MHz
MAX5180/83-21
78
SIGNAL-TO-NOISE PLUS DISTORTION
vs. OUTPUT FREQUENCY
MAX5180/83-20
SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT
FREQUENCY AND CLOCK FREQUENCY, DAC2
MAX5180/83-19
SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT
FREQUENCY AND CLOCK FREQUENCY, DAC1
76
SFDR (dBc)
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
60
0
2
4
6
8
10 12 14 16 18 20
OUTPUT FREQUENCY (MHz)
0.5
0.75
1
1.25
FULL-SCALE OUTPUT CURRENT (mA)
_______________________________________________________________________________________
1.5
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
PIN
NAME
FUNCTION
1
CREF1
Reference Bias Bypass, DAC1
2
OUT1P
Positive Analog Output, DAC1. Current output for MAX5180; voltage output for MAX5183.
3
OUT1N
Negative Analog Output, DAC1. Current output for MAX5180; voltage output for MAX5183.
4
AGND
Analog Ground
5
AVDD
Analog Positive Supply, +2.7V to +3.3V
DAC Enable, Digital Input
0: Enter DAC standby mode with PD = DGND
1: Power-up DAC with PD = DGND
X: Enter shutdown mode with PD = DVDD (X = don’t care)
6
DACEN
7
PD
Power-Down Select
0: Enter DAC standby mode (DACEN = DGND) or power-up DAC (DACEN = DVDD)
1: Enter shutdown mode.
8
CS
Active-Low Chip Select
9
CLK
Clock Input
10
N.C.
No Connect. Do not connect to this pin.
11
REN
Active-Low Reference Enable. Connect to DGND to activate on-chip +1.2V reference.
12
D0
Data Bit D0 (LSB)
13–20
D1–D8
Data Bits D1–D8
21
D9
22
DVDD
Digital Supply, +2.7V to +3.3V
23
DGND
Digital Ground
24
REFR
Reference Input
25
REFO
Reference Output
26
OUT2N
Negative Analog Output, DAC2. Current output for MAX5180; voltage output for MAX5183.
27
OUT2P
Positive Analog Output, DAC2. Current output for MAX5180; voltage output for MAX5183.
28
CREF2
Reference Bias Bypass, DAC2
Data Bit D9 (MSB)
_______________________________________________________________________________________
7
MAX5180/MAX5183
______________________________________________________________Pin Description
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
REN
AVDD
AGND
CS
DACEN
PD
1.2V REF
REFO
CREF1
CURRENTSOURCE ARRAY
REFR
CREF2
OUT1P
*9.6k
OUT1N
DAC 1 SWITCHES
OUT2P
DAC 2 SWITCHES
MSB DECODE
CLK
MSB DECODE
INPUT
LATCHES
INPUT
LATCHES
MAX5180
MAX5183
DVDD
*INTERNAL 400Ω AND 9.6kΩ
RESISTORS FOR MAX5183 ONLY.
400Ω*
400Ω*
400Ω *
400Ω*
OUTPUT
LATCHES
OUTPUT
LATCHES
OUT2N
DGND
D9–D0
Figure 1. Functional Diagram
Detailed Description
The MAX5180/MAX5183 are dual 10-bit digital-to-analog converters (DACs) capable of operating with clock
speeds up to 40MHz. Each of these dual converters
consists of separate input and DAC registers, followed
by a current source array capable of generating up to
1.5mA full-scale output current (Figure 1). An integrated +1.2V voltage reference and control amplifier determine the data converters’ full-scale output currents/
voltages. Careful reference design ensures close gain
matching and excellent drift characteristics. The
MAX5183’s voltage output operation features matched
400Ω on-chip resistors that convert the current array
current into a voltage.
Internal Reference and Control Amplifier
The MAX5180/MAX5183 provide an integrated
50ppm/°C, +1.2V, low-noise bandgap reference that
can be disabled and overridden by an external reference voltage. REFO serves either as an external reference input or an integrated reference output. If REN is
connected to AGND, the internal reference is selected
and REFO provides a +1.2V output. Due to its limited
8
10µA output drive capability, REFO must be buffered
with an external amplifier if heavier loading is required.
The MAX5180/MAX5183 also employ a control amplifier
designed to simultaneously regulate the full-scale output current (IFS) for both outputs of the devices. The
output current is calculated as follows:
IFS = 8 · IREF
where I REF is the reference output current (I REF =
VREFO/RSET) and IFS is the full-scale output current.
R SET is the reference resistor that determines the
amplifier’s output current on the MAX5180 (Figure 2).
This current is mirrored into the current-source array
where it is equally distributed between matched current
segments and summed to valid output current readings
for the DACs.
The MAX5183 converts each output current (DAC1 and
DAC2) into an output voltage (VOUT1, VOUT2) with two
internal, ground-referenced 400Ω load resistors. Using
the internal +1.2V reference voltage, the MAX5183’s
integrated reference output current resistor (RSET =
9.6kΩ) sets IREF to 125µA and IFS to 1mA.
_______________________________________________________________________________________
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
MAX5180/MAX5183
OPTIONAL EXTERNAL BUFFER
FOR HEAVIER LOADS
REN
AGND
+1.2V
BANDGAP
REFERENCE
MAX4040
REFO
CCOMP*
REFR
CURRENTSOURCE ARRAY
IREF
IFS
AGND
IREF =
VREF
RSET
RSET
RSET **
9.6k
MAX5180
MAX5183
AGND
*COMPENSATION CAPACITOR (CCOMP ≈ 100nF).
**9.6kΩ REFERENCE CURRENT-SET RESISTOR
INTERNAL TO MAX5183 ONLY. USE EXTERNAL
RSET FOR MAX5180.
Figure 2. Setting IFS with the Internal +1.2V Reference and the Control Amplifier
AVDD
10µF
REN
0.1µF
AGND
+1.2V
BANDGAP
REFERENCE
AVDD
EXTERNAL
+1.2V
REFERENCE
REFO
CURRENTSOURCE ARRAY
REFR
MAX6520
IREF
AGND
RSET
AGND
IFS
RSET
9.6k*
MAX5180
MAX5183
*9.6kΩ REFERENCE CURRENT-SET RESISTOR
INTERNAL TO MAX5183 ONLY. USE EXTERNAL
RSET FOR MAX5180.
Figure 3. MAX5180/MAX5183 with External Reference
_______________________________________________________________________________________
9
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
External Reference
Shutdown Mode
To disable the MAX5180/MAX5183’s internal reference,
connect REN to AVDD. A temperature-stable, external
reference may now be applied to drive the REFO pin to
set the full-scale output (Figure 3). Choose a reference
capable of supplying at least 150µA to drive the bias
circuit that generates the cascode current for the current array. For improved accuracy and drift performance, choose a fixed output voltage reference such
as the +1.2V, 25ppm/°C MAX6520 bandgap reference.
For lowest power consumption, the MAX5180/MAX5183
provide a power-down mode in which the reference,
control amplifier, and current array are inactive and the
DAC supply current is reduced to 1µA. To enter this
mode, connect PD to DVDD. To return to active mode,
connect PD to DGND and DACEN to DVDD. Table 1
lists the power-down mode selection. About 50µs are
required for the parts to leave shutdown mode and settle to their outputs’ values prior to shutdown.
Standby Mode
Timing Information
To enter the lower power standby mode, connect digital
inputs PD and DACEN to DGND. In standby, both the
reference and the control amplifier are active with the
current array inactive. To exit this condition, DACEN
must be pulled high with PD held at DGND. Both the
MAX5180 and MAX5183 typically require 50µs to wake
up and allow both the outputs and the reference to settle.
Both DAC cells in the MAX5180/MAX5183 write to their
outputs simultaneously (Figure 4). The input latch of the
first DAC (DAC1) is loaded after the clock signal transitions high. When the clock signal transitions low, the
input latch of the second DAC (DAC2) is loaded.
Simultaneously at the rising edge of the next clock, the
contents of both input latches are shifted to the DAC
registers and their outputs are updated.
tCP
tCL
tCH
CLK
N-1
D0–D9
N-1
DAC1
tDS1
DAC2
N
N
DAC1
tDS2
N+1
DAC2
N+1
DAC1
DAC2
tDH2
tDH1
OUT1
N-1
N
N+1
OUT2
N-1
N
N+1
Figure 4. Timing Diagram
Table 1. Power-Down Mode Selection
PD
(POWER-DOWN SELECT)
DACEN
(DAC ENABLE)
POWER-DOWN MODE
0
0
Standby
0
1
Wake-Up
1
X
Shutdown
OUTPUT STATE
MAX5180
High-Z
MAX5183
AGND
Last state prior to standby mode
MAX5180
High-Z
MAX5183
AGND
X = Don’t care
10
______________________________________________________________________________________
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
Applications Information
Static and Dynamic Performance
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) (Figure 5a) is the deviation of
the values on an actual transfer function from either a
best-straight-line fit (closest approximation to the actual
transfer curve) or a line drawn between the endpoints
of the transfer function once offset and gain errors have
been nullified. For a DAC, the deviations are measured
every single step.
Differential Nonlinearity
Differential nonlinearity (DNL) (Figure 5b) is the difference between an actual step height and the ideal value
of 1LSB. A DNL error specification of less than 1LSB
guarantees no missing codes and a monotonic transfer
function.
Offset Error
Offset error (Figure 5c) is the difference between the
ideal and the actual offset point. For a DAC, the offset
point is the step value when the digital input is zero.
This error affects all codes by the same amount and
can usually be compensated by trimming.
7
6
ANALOG OUTPUT VALUE
ANALOG OUTPUT VALUE
6
5
4
AT STEP
011 (1/2 LSB )
3
2
DIFFERENTIAL LINEARITY
ERROR (-1/4 LSB)
4
3
1 LSB
2
DIFFERENTIAL
LINEARITY ERROR (+1/4 LSB)
1
AT STEP
001 (1/4 LSB )
1
1 LSB
5
0
0
000
001
010
011
100
101
110
000
111
001
IDEAL DIAGRAM
IDEAL OFFSET
POINT
0
000
001
OFFSET ERROR
(+1 1/4 LSB)
ANALOG OUTPUT VALUE
ANALOG OUTPUT VALUE
2
ACTUAL
OFFSET
POINT
101
GAIN ERROR
(-1 1/4 LSB)
6
IDEAL DIAGRAM
ACTUAL
FULL-SCALE
OUTPUT
5
4
0
010
011
000 100
101
110
111
DIGITAL INPUT CODE
DIGITAL INPUT CODE
Figure 5c. Offset Error
100
IDEAL FULL-SCALE OUTPUT
7
ACTUAL
DIAGRAM
1
011
Figure 5b. Differential Nonlinearity
Figure 5a. Integral Nonlinearity
3
010
DIGITAL INPUT CODE
DIGITAL INPUT CODE
Figure 5d. Gain Error
______________________________________________________________________________________
11
MAX5180/MAX5183
Outputs
The MAX5180 outputs are designed to supply full-scale
output currents of 1mA into 400Ω loads in parallel with
a capacitive load of 5pF. The MAX5183 features integrated 400Ω resistors that restore the array currents to
proportional, differential voltages of 400mV. These differential output voltages can then be used to drive a
balun transformer or a low-distortion, high-speed operational amplifier to convert the differential voltage into a
single-ended voltage.
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
Gain Error
Gain error (Figure 5d) is the difference between the
ideal and the actual full-scale output voltage on the
transfer curve after nullifying the offset error. This error
alters the slope of the transfer function and corresponds to the same percentage error in each step.
Settling Time
Settling time is the amount of time required from the start
of a transition until the DAC output settles its new output
value to within the converter’s specified accuracy.
Digital Feedthrough
Digital feedthrough is the noise generated on a DAC’s
output when any digital input transitions. Proper board
layout and grounding will significantly reduce this
noise, but there will always be some feedthrough
caused by the DAC itself.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of the input signal’s first five harmonics to the fundamental itself. This is expressed as:

2
2
2
2
 V2 + V3 + V4 + V5
THD = 20 ⋅log
V1







where V1 is the fundamental amplitude, and V2 through
V5 are the amplitudes of the 2nd- through 5th-order
harmonics.
Spurious-Free Dynamic Range
Spurious-free dynamic range (SFDR) is the ratio of RMS
amplitude of the fundamental (maximum signal component) to the RMS value of the next-largest distortion
component.
Differential to Single-Ended Conversion
The MAX4108 low-distortion, high-input bandwidth
amplifier may be used to generate a voltage from the
array current output of the MAX5180. The differential
voltage across OUT1P (or OUT2P) and OUT1N (or
OUT2N) is converted into a single-ended voltage by
designing an appropriate operational amplifier configuration (Figure 6).
I/Q Reconstruction in a QAM Application
The MAX5180/MAX5183’s low-distortion supports analog reconstruction of in-phase (I) and quadrature (Q)
carrier components typically used in QAM (quadrature
12
amplitude modulation) architectures where I and Q
data are interleaved on a common data bus. A QAM
signal is a carrier frequency that is both amplitude and
phase modulated, and is created by summing two
independently modulated carriers of identical frequency
but different phase (90° phase difference).
In a typical QAM application (Figure 7), the modulation
occurs in the digital domain and the MAX5180/
MAX5183’s dual DACs may be used to reconstruct the
analog I and Q components.
The I/Q reconstruction system is completed by a quadrature modulator that combines the reconstructed I and
Q components with in-phase and quadrature phase
carrier frequencies, then sums both outputs to provide
the QAM signal.
Grounding and Power-Supply Decoupling
Grounding and power-supply decoupling strongly influence the MAX5180/MAX5183’s performance. Unwanted
digital crosstalk may couple through the input, reference, power-supply, and ground connections, which
may affect dynamic specifications like signal-to-noise
ratio or spurious-free dynamic range. In addition, electromagnetic interference (EMI) can either couple into or
be generated by the MAX5180/MAX5183. Therefore,
grounding and power-supply decoupling guidelines for
high-speed, high-frequency applications should be
closely followed.
First, a multilayer pc board with separate ground and
power-supply planes is recommended. High-speed
signals should be run on controlled impedance lines
directly above the ground plane. Since the MAX5180/
MAX5183 have separate analog and digital ground
buses (AGND and DGND, respectively), the PC board
should also have separate analog and digital ground
sections with only one point connecting the two. Digital
signals should run above the digital ground plane, and
analog signals should run above the analog ground
plane.
Both devices have two power-supply inputs: analog
VDD (AVDD) and digital VDD (DVDD). Each AVDD input
should be decoupled with parallel 10µF and 0.1µF
ceramic-chip capacitors. These capacitors should be as
close to the pin as possible, and their opposite ends
should be as close to the ground plane as possible. The
DVDD pins should also have separate 10µF and 0.1µF
capacitors adjacent to their respective pins. Try to minimize analog load capacitance for proper operation. For
best performance, it is recommended to bypass CREF1
and CREF2 with low-ESR 0.1µF capacitors to AVDD.
______________________________________________________________________________________
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
10µF
+3V
AVDD
0.1µF
0.1µF
10µF
MAX5180/MAX5183
AVDD
+3V
0.1µF
0.1µF
AVDD
402Ω
DVDD CREF1
CREF2
+5V
402Ω
OUT1P
CLK
OUTPUT1
400Ω*
MAX4108
MAX5180
MAX5183
D0–D9
-5V
OUT1N
402Ω
402Ω
400Ω*
402Ω
REFO
+5V
402Ω
0.1µF
OUT2P
OUTPUT2
400Ω*
REFR
MAX4108
-5V
RSET**
OUT2N
402Ω
402Ω
400Ω*
DGND
REN
AGND
*400Ω RESISTORS INTERNAL TO MAX5183 ONLY.
**MAX5180 ONLY
Figure 6. Differential to Single-Ended Conversion Using a Low-Distortion Amplifier
The power-supply voltages should also be decoupled
with large tantalum or electrolytic capacitors at the
point they enter the PC board. Ferrite beads with additional decoupling capacitors forming a pi network can
also improve performance.
Chip Information
TRANSISTOR COUNT: 9464
SUBSTRATE CONNECTED TO AGND
______________________________________________________________________________________
13
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
+3V
+3V
+3V
DAC1
DIGITAL
SIGNAL
PROCESSOR
I COMPONENT
BP
FILTER
CARRIER
FREQUENCY
MAX5180
MAX5183
Q COMPONENT
DAC2
0°
Σ
90°
BP
FILTER
MAX2452
QUADRATURE
MODULATOR
Figure 7. Using the MAX5180/MAX5183 for I/Q Signal Reconstruction
14
______________________________________________________________________________________
IF
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
QSOP.EPS
______________________________________________________________________________________
15
MAX5180/MAX5183
Package Information
MAX5180/MAX5183
Dual, 10-Bit, 40MHz, Current/Voltage
Simultaneous-Output DACs
NOTES
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.