Information TAPING SPECIFICATIONS AND PACKING OUTLINE DRAWING OF 24/28/36-PIN QFN PACKAGE FOR SILICON MMIC Document No. P15542EJ1V0IF00 (1st edition) Date Published September 2001 NS CP(K) © Printed in Japan 2001 [MEMO] 2 Information P15542EJ1V0IF • The information in this document is current as of September, 2001. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 Information P15542EJ1V0IF 3 [MEMO] 4 Information P15542EJ1V0IF CONTENTS 1. DESCRIPTION ........................................................................................................................................ 6 2. INDICATION OF PART NUMBER ....................................................................................................... 6 2.1 Indication of Part Number............................................................................................................. 6 2.2 Device Orientation in the Carrier Tape........................................................................................ 6 2.3 An Example of Indication.............................................................................................................. 6 3. TAPE AND REEL SPECIFICATIONS.................................................................................................. 7 3.1 Tape Dimensions........................................................................................................................... 7 3.1.1 24-pin QFN Package ............................................................................................................................7 3.1.2 28-pin QFN Package ............................................................................................................................8 3.1.3 36-pin QFN Package ............................................................................................................................9 3.2 Reel Dimensions.......................................................................................................................... 10 3.3 Leader and Trailer of Carrier Tape (Used Commonly for 3 Package Types)......................... 11 3.4 Sealing Strength between Tapes ............................................................................................... 12 4. PACKING .............................................................................................................................................. 12 4.1 Quantity of Packing..................................................................................................................... 12 4.2 Indication of Part Number and Quantity to the Reel ................................................................ 12 4.3 Indication of Part Number and Quantity to the Packing Case ................................................ 12 5. PACKING OUTLINE DRAWING (Used Commonly for 3 Package Types)............................... 13 5.1 Tape and Reel .............................................................................................................................. 13 5.2 Packing Box Specifications........................................................................................................ 13 Information P15542EJ1V0IF 5 1. DESCRIPTION This specification covers standards on tape and reel of the 24/28/36-pin QFN package for high frequency semiconductors on NEC electron devices. 2. INDICATION OF PART NUMBER The part number of tape and reel packing device is following. 2.1 Indication of Part Number Part number of device Symbol of device orientation (cf. 2.2) Indicating the embossed carrier tape 2.2 Device Orientation in the Carrier Tape Pin 1 of the device faces toward the open end of the tape, away from the reel. (Pin 1 is on the opposite side to the tape sprocket roles.) Caution Only “-E1” type taping is supported for this package. -E1 the reel open end Tape drawout direction Pin 1 indication 2.3 An Example of Indication µPC8186K-E1: The tape and reel packing µPC8186K, in which pin 1 of the device faces toward open end of the tape. 6 Information P15542EJ1V0IF 3. TAPE AND REEL SPECIFICATIONS 3.1 Tape Dimensions 3.1.1 24-pin QFN Package P1 φ D0 P0 E T1 W B0 F P2 A0 T2 φ D1 Tape drawout direction (Unit: mm) Symbol A0 B0 φD0 φD1 E F P0 P1 P2 T1 T2 W S pecification 4.5 ±0.1 5.5 ±0.1 φ1.5 +0.1 −0 φ1.5 MIN. 1.75 ±0.1 5.5 ±0.05 4.0 ±0.1 8.0 ±0.1 2.0 ±0.05 0.3 1.3 12.0 ±0.3 The dimensions of the A0 and B0 are indicated inside of the bottom of the pocket. This carrier tape is applied treatment of electro static prevention. Information P15542EJ1V0IF 7 3.1.2 28-pin QFN Package P1 φ D0 P0 E T1 W B0 F P2 A0 T2 φ D1 Tape drawout direction (Unit: mm) Symbol A0 B0 φD0 φD1 E F P0 P1 P2 T1 T2 W S pecification 5.3 ±0.1 6.0 ±0.1 φ1.5 +0.1 −0 φ1.5 MIN. 1.75 ±0.1 5.5 ±0.05 4.0 ±0.1 8.0 ±0.1 2.0 ±0.05 0.3 1.3 12.0 ±0.3 The dimensions of the A0 and B0 are indicated inside of the bottom of the pocket. This carrier tape is applied treatment of electro static prevention. 8 Information P15542EJ1V0IF 3.1.3 36-pin QFN Package P1 φ D0 P0 E T1 W B0 F P2 A0 T2 φ D1 Tape drawout direction (Unit: mm) Symbol A0 B0 φD0 φD1 E F P0 P1 P2 T1 T2 W S pecification 6.5 ±0.1 6.5 ±0.1 φ1.5 +0.1 −0 φ1.5 MIN. 1.75 ±0.1 5.5 ±0.05 4.0 ±0.1 8.0 ±0.1 2.0 ±0.05 0.3 ±0.05 1.3 12.0 ±0.3 The dimensions of the A0 and B0 are indicated inside of the bottom of the pocket. This carrier tape is applied treatment of electro static prevention. Information P15542EJ1V0IF 9 A C B 3.2 Reel Dimensions F E θ1 W1 W2 D Magnification figure of F part (Unless otherwise specified, Unit: mm) Symbol A B C D E W1 W2 θ1 S p ecification φ330 ±2 φ100 ±1 φ13.0 ±0.2 φ21.0 ±0.8 2.0 ±0.5 13.5±1 17.5±1 120° This reel applied treatment of electro static prevention. 10 Information P15542EJ1V0IF 3.3 Leader and Trailer of Carrier Tape (Used Commonly for 3 Package Types) Adhesive tape Empty carrier tape Cover tape only Trailer Leader Label (Unit: mm) Item Leader − Cover tape Empty carrier tape Trailer Specification Empty carrier tape Remarks Tip taped to roll, and fixed by adhesive tape 100 MIN. The winding direction is shown above 400 MIN. Length of cover tape + empty carrier tape 160 MIN. Information P15542EJ1V0IF 11 3.4 Sealing Strength between Tapes Item Data Cover tape adhesion 0.1 to 1.3 N Remarks Peeling angle: 165° to 180°, Peeling speed: 300±10 mm/min Cover tape 165˚ to 180˚ Carrier tape Direction of tape 4. PACKING 4.1 Quantity of Packing 2 500 pieces/reel 4.2 Indication of Part Number and Quantity to the Reel Part number, quantity, rank and lot number are indicated at the side of the reel. 4.3 Indication of Part Number and Quantity to the Packing Case Part number, quantity, rank and lot number are indicated at the side of packing case. 12 Information P15542EJ1V0IF 5. PACKING OUTLINE DRAWING (Used Commonly for 3 Package Types) 5.1 Tape and Reel -E1 Type Direction of feed Label 5.2 Packing Box Specifications L H Label W Contents of Label Indication Part Number, Quantity, Lot Number, Class Tape and Reel Packing Box Quantity (pcs) Dimension (mm) (W × H × L) Quantity (reel) 2 500 343 × 53 × 343 2 Remark Dimensions and maximum quantity of a packing box are for shipment. In some using case, the packing box might replace another box. Information P15542EJ1V0IF 13 [MEMO] 14 Information P15542EJ1V0IF Facsimile Message From: Name Company Tel. Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation. Please complete this form whenever you'd like to report errors or suggest improvements to us. FAX Address Thank you for your kind support. North America Hong Kong, Philippines, Oceania NEC Electronics Inc. NEC Electronics Hong Kong Ltd. Corporate Communications Dept. Fax: +852-2886-9022/9044 Fax: +1-800-729-9288 +1-408-588-6130 Korea Europe NEC Electronics Hong Kong Ltd. NEC Electronics (Europe) GmbH Seoul Branch Technical Documentation Dept. Fax: +82-2-528-4411 Fax: +49-211-6503-274 South America NEC do Brasil S.A. Fax: +55-11-6462-6829 Asian Nations except Philippines NEC Electronics Singapore Pte. Ltd. Fax: +65-250-3583 Japan NEC Semiconductor Technical Hotline Fax: +81- 44-435-9608 Taiwan NEC Electronics Taiwan Ltd. Fax: +886-2-2719-5951 I would like to report the following error/make the following suggestion: Document title: Document number: Page number: If possible, please fax the referenced page or drawing. Document Rating Excellent Good Acceptable Poor Clarity Technical Accuracy Organization CS 01.2