MAXIM MAXQ3183-RAN+

19-4955; Rev 0; 12/09
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The MAXQ3183 is a dedicated electricity measurement
front-end that collects and calculates polyphase voltage, current, power, energy, and many other metering
and power-quality parameters of a polyphase load. The
computed results can be retrieved by an external master through the on-chip serial peripheral interface
(SPI™) bus. This bus is also used by the external master to configure the operation of the MAXQ3183 and
monitor the status of operations.
The MAXQ3183 performs voltage and current measurements using an integrated ADC that can measure up to
seven external differential signal pairs. An eighth differential signal pair is used to measure the die temperature. An internal amplifier automatically adjusts the
current channel gain to compensate for low-current
channel-signal levels.
Applications
3-Phase Multifunction Electricity Meters
Features
♦ Compatible with 3-Phase/3-Wire, 3-Phase/4-Wire
♦ Phase Current THDN
♦ Fundamental and Total Power and Energy
♦ AC/DC Mode Current and Voltage Measurement
♦ Two Pulse Outputs: Configurable for Active,
Reactive, and Apparent Powers
♦ Programmable Meter Constants and Pulse Widths
♦ Programmable No-Load Current Threshold
♦ Programmable Thresholds for Undervoltage and
Overvoltage Detection
♦ Programmable Threshold for Overcurrent Detection
♦ Programmable Vector Sum Threshold for Bypass
Detection
♦ Amp-Hours in Absence of Voltage Signals
♦ On-Chip Digital Temperature Sensor
♦ Precision Internal Voltage Reference 2.048V
(30ppm/°C typical), Also Supports An External
Voltage Reference
♦ Supports Software Meter Calibration
♦ Active Power and Energy of Each Phase and
Combined 3-Phase (kWh), Positive and Negative
♦ Up to 3-Point Multipoint Calibration to
Compensate for Transducer Nonlinearity
♦ Reactive Power and Energy of Each Phase and
Combined, Positive and Negative
♦ Power-Fail Detection
♦ Bidirectional Reset Input/Output
♦ Apparent Power and Energy of Each Phase and
Combined 3-Phase
♦ SPI-Compatible Serial Interface with Interrupt
♦ Neutral Line Current Measurement
♦ Vector Sum of 3-Phase Currents and Neutral
Current
♦ Line Frequency (Hz)
♦ Power Factors
♦ Voltage Phasor Angles
Request (IRQ) Output
♦ Single 3.3V Supply, Low Power (35mW typical)
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAXQ3183-RAN+
-40°C to +85°C
28 TSSOP
+Denotes a lead(Pb)-free/RoHS-compliant package.
♦ Voltage and Current Phase Sequence Indications
♦ Phase Voltage Absence Detection
♦ Voltage and Current Harmonic Measurement
Pin Configuration and Typical Application Circuit appear at
end of data sheet.
MAXQ is a registered trademark of Maxim Integrated Products, Inc.
SPI is a trademark of Motorola, Inc.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be
simultaneously available through various sales channels. For information about device errata, go to: www.maxim-ic.com/errata.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAXQ3183
General Description
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
TABLE OF CONTENTS
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Metering Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SPI Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Analog Front-End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Digital Signal Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Precision Pulse Generators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SPI Peripheral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Reset Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Watchdog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power-Supply Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
External High-Frequency Crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
External High-Frequency Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Internal RC Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Master Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SPI Communications Rate and Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SPI Communications Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Host Software Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Register Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
RAM-Based Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
General Operating Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Global Status Register (STATUS) (0x000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Operating Mode Register 0 (OPMODE0) (0x001) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Operating Mode Register 1 (OPMODE1) (0x002) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Operating Mode Register 2 (OPMODE2) (0x003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
2
_______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Global Interrupt Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Interrupt Request Flag Register (IRQ_FLAG) (0x004) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Interrupt Mask Register (IRQ_MASK) (0x006) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Meter Pulse Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Pulse Configuration—CFP Output (PLSCFG1) (0x01E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Pulse Configuration—CFQ Output (PLSCFG2) (0x01F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
CFP Pulse Width (PLS1_WD) (0x020) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
CFP Pulse Threshold (THR1) (0x022) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
CFQ Pulse Width (PLS2_WD) (0x026) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
CFQ Pulse Threshold (THR2) (0x028) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Calibration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Current Gain, Phase X = A/B/C/N (X.I_GAIN) (A: 0x130, B: 0x21C, C: 0x308, N: 0x12E) . . . . . . . . . . . . . . . . . .37
Voltage Gain, Phase X = A/B/C (X.V_GAIN) (A: 0x132, B: 0x21E, C: 0x30A) . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Energy Gain, Phase X = A/B/C (X.E_GAIN) (A: 0x134, B: 0x220, C: 0x30C) . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Phase-Angle Compensation, High Range, Phase X = A/B/C (X.PA0) (A: 0x13E, B: 0x22A, C: 0x316) . . . . . . . .38
Phase-Angle Compensation, Medium Range, Phase X = A/B/C (X.PA1) (A: 0x140, B: 0x22C, C: 0x318) . . . . .39
Phase-Angle Compensation, Low Range, Phase X = A/B/C (X.PA2) (A: 0x142, B: 0x22E, C: 0x31A) . . . . . . . . .39
Limit Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Overcurrent Level (OCLVL) (0x044) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Overvoltage Level (OVLVL) (0x046) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Undervoltage Level (UVLVL) (0x048) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
No-Load Level (NOLOAD) (0x04A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Current Vector Sum Threshold (ISUMLVL) (0x054) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Phase Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Interrupt Flags, Phase X = A/B/C (X.FLAGS) (A: 0x144, B: 0x230, C: 0x31C) . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Interrupt Mask, Phase X = A/B/C (X.MASK) (A: 0x145, B: 0x231, C: 0x31D) . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Energy Overflow Flags, Phase X = A/B/C (X.EOVER) (A: 0x146, B: 0x232, C: 0x31E) . . . . . . . . . . . . . . . . . . . . .42
Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Line Frequency (LINEFR) (0x062) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Power Factor, Phase X = A/B/C (X.PF) (A: 0x1C6, B: 0x2B2, C: 0x39E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
RMS Voltage, Phase X = A/B/C (X.VRMS) (A: 0x1C8, B: 0x2B4, C: 0x3A0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
RMS Current, Phase X = A/B/C (X.IRMS) (A: 0x1CC, B: 0x2B8, C: 0x3A4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Energy, Real Positive, Phase X = A/B/C (X.EAPOS) (A: 0x1E8, B: 0x2D4, C: 0x3C0) . . . . . . . . . . . . . . . . . . . . .44
Energy, Real Negative, Phase X = A/B/C (X.EANEG) (A: 0x1EC, B: 0x2D8, C: 0x3C4) . . . . . . . . . . . . . . . . . . . .45
Energy, Reactive Positive, Phase X = A/B/C (X.ERPOS) (A: 0x1F0, B: 0x2DC, C: 0x3C8) . . . . . . . . . . . . . . . . . .45
Energy, Reactive Negative, Phase X = A/B/C (X.ERNEG) (A: 0x1F4, B: 0x2E0, C: 0x3CC) . . . . . . . . . . . . . . . . .46
Energy, Apparent, Phase X = A/B/C (X.ES) (A: 0x1F8, B: 0x2E4, C: 0x3D0) . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
_______________________________________________________________________________________
3
MAXQ3183
TABLE OF CONTENTS (continued)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
TABLE OF CONTENTS (continued)
Virtual Register Conversion Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Voltage Units Conversion Coefficient (VOLT_CC) (0x014) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Current Units Conversion Coefficient (AMP_CC) (0x016) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Power Units Conversion Coefficient (PWR_CC) (0x018) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Energy Units Conversion Coefficient (ENR_CC) (0x01A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Temperature Conversion Coefficient (TEMP_CC) (0x060) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Virtual Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Real Power, Phase X = A/B/C/T (PWRP.X) (A: 0x801, B: 0x802, C: 0x804, T: 0x807) . . . . . . . . . . . . . . . . . .51
Reactive Power, Phase X = A/B/C/T (PWRQ.X) (A: 0x811, B: 0x812, C: 0x814, T: 0x817) . . . . . . . . . . . . . .51
Apparent Power, Phase X = A/B/C/T (PWRS.X) (A: 0x821, B: 0x822, C: 0x824, T: 0x827) . . . . . . . . . . . . . .52
Voltage and Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
RMS Volts, Phase X = A/B/C (V.X) (A: 0x831, B: 0x832, C: 0x834) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
RMS Amps, Phase X = A/B/C/N (I.X) (A: 0x841, B: 0x842, C: 0x844, N: 0x840) . . . . . . . . . . . . . . . . . . . . . .52
Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Power Factor (PF.T) (0x867) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Real Energy, Phase A/B/C/T (ENRP.X) (A: 0x8C1, B: 0x8C2, C: 0x8C4, T: 0x8C7) . . . . . . . . . . . . . . . . . . . .53
Reactive Energy, Phase A/B/C/T (ENRQ.X) (A: 0x8D1, B: 0x8D2, C: 0x8D4, T: 0x8D7) . . . . . . . . . . . . . . . .53
Apparent Energy, Phase A/B/C/T (ENRS.X) (A: 0x871, B: 0x872, C: 0x874, T: 0x877) . . . . . . . . . . . . . . . . .53
Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Analog Front-End Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Digital Signal Processing (DSP) Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Digital Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Per Sample Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Per DSP Cycle Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Energy Accumulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
No-Zero-Crossing Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Phase Sequence Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
RMS Voltage, RMS Current, and Energy Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Power Calculation (Active, Reactive, Apparent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Energy Accumulation Start Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
No-Load Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
On Demand Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
RMS Volts, RMS Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
4
_______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Line Frequency
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Phasor Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Meter Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Generating Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Meter Constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Overvoltage and Overcurrent Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Meter Units to Real Units Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Units Conversion Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Calibration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Calibrating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Calibrating Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Calibrating Phase Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Interfacing the MAXQ3183 to External Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Connections to the Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Sensor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Voltage Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Voltage-Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Voltage Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Current Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Current Shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Current Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Advanced Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Modifying the ADC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Fine-Tuning the DSP Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Fine-Tuning the Line Frequency Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Fundamental Mode Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Harmonic Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Current Total Harmonic Distortion Plus Noise (THDN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Current Vector Sum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Low-Power Measurement Mode (LOWPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Advanced Calibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Calibrating Current Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Calibrating Linearity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
_______________________________________________________________________________________
5
MAXQ3183
TABLE OF CONTENTS (continued)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
TABLE OF CONTENTS (continued)
Calibrating Power/Energy Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Multipoint Phase Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Advanced Register Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Analog Scan Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Time Slot Assignment—Current Channel X = A/B/C (SCAN_IX) (A: 0x008, B: 0x00C, C: 0x00A) . . . . . . . . .73
Time Slot Assignment—Voltage Channel X = A/B/C (SCAN_VX) (A: 0x009, B: 0x00D, C: 0x00B) . . . . . . . .74
Time Slot Assignment—Neutral Current Channel (SCAN_IN) (0x00E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Time Slot Assignment—Temperature Channel (SCAN_TE) (0x00F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Neutral Current and Harmonics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Auxiliary Channel Configuration (AUX_CFG) (0x010) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
DSP System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
System Clock Frequency (SYS_KHZ) (0x012) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Cycle Count (CYCNT) (0x01C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Number of Scan Frames per DSP Cycle (NS) (0x040) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Line Cycle Noise Rejection Filter (REJ_NS) (0x02C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Line Cycle Averaging Filter (AVG_NS) (0x02E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Meter Measurement Averaging Filter (AVG_C) (0x030) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Meter Measurement Highpass Filter (HPF_C) (0x032) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Fundamental Filter Feed-Forward Coefficient (B0FUND) (0x034) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Fundamental Filter Feedback Coefficient (A1FUND) (0x036) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Harmonic Filter Feed-Forward Coefficient (B0HARM) (0x03A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Harmonic Filter Feedback Coefficient (A1HARM) (0x03C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Zero-Cross Lowpass Filter (ZC_LPF) (0x05A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Hardware Mirror Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
ADC Configuration (R_ACFG) (0x04C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
ADC Conversion Rate (R_ADCRATE) (0x04E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
ADC Settling Time (R_ADCACQ) (0x050) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
SPI Configuration (R_SPICF) (0x052) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Timeouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Communications Timeout (COM_TIMO) (0x056) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Energy Accumulation Timeout (ACC_TIMO) (0x058) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Phase-Angle Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Phase Offset Current Threshold 1 (I1THR) (0x05C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Phase Offset Current Threshold 2 (I2THR) (0x05E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
6
_______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Miscellaneous Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Neutral Current Gain (N.I_GAIN) (0x12E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Gain, Fundamental Energy, Phase X = A/B/C (X.EF_GAIN) (A: 0x136, B: 0x222, C: 0x30E) . . . . . . . . . . . . .88
Linearity Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Linearity Offset, High Range, Phase X = A/B/C (X.OFFS_HI) (A: 0x138, B: 0x224, C: 0x310) . . . . . . . . . . . .88
Linearity Gain Coefficient, Low Range, Phase X = A/B/C (X.GAIN_LO) (A: 0x13A, B: 0x226, C: 0x312) . . .88
Linearity Offset, Low Range, Phase X = A/B/C (X.OFFS_LO) (A: 0x13C, B: 0x228, C: 0x314) . . . . . . . . . . .89
Measurements—RAM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
On-Demand RMS Result (N.IRMS) (0x11C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Fundamental Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Fundamental Energy Overflow Flags, Phase X = A/B/C (X.EFOVER) (A: 0x147, B: 0x233, C: 0x31F) . . . . .90
Energy, Fundamental, Real Positive, Phase X = A/B/C (X.EAFPOS) (A: 0x1FC, B: 0x2E8, C: 0x3D4) . . . . .90
Energy, Fundamental, Real Negative, Phase X = A/B/C (X.EAFNEG) (A: 0x200, B: 0x2EC, C: 0x3D8) . . . .91
Energy, Fundamental, Reactive Positive, Phase X = A/B/C (X.ERFPOS) (A: 0x204, B: 0x2F0, C: 0x3DC) . .91
Energy, Fundamental, Reactive Negative, Phase X = A/B/C (X.ERFNEG) (A: 0x208, B: 0x2F4, C: 0x3E0) .92
Energy Fundamental, Apparent, Phase X = A/B/C (X.ESF) (A: 0x20C, B: 0x2F8, C: 0x3E4) . . . . . . . . . . . . .92
Energy Accumulated in the Last DSP Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Real Energy, Phase X = A/B/C (X.ACT) (A: 0x1D0, B: 0x2BC, C: 0x3A8) . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Reactive Energy, Phase X = A/B/C (X.REA) (A: 0x1D4, B: 0x2C0, C: 0x3AC) . . . . . . . . . . . . . . . . . . . . . . . .93
Apparent Energy, Phase X = A/B/C (X.APP) (A: 0x1D8, B: 0x2C4, C: 0x3B0) . . . . . . . . . . . . . . . . . . . . . . . .94
Fundamental Energy Accumulated in the Last DSP Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Fundamental Real Energy, Phase X = A/B/C (X.ACTF) (A: 0x1DC, B: 0x2C8, C: 0x3B4) . . . . . . . . . . . . . . .94
Fundamental Reactive Energy, Phase X = A/B/C (X.REAF) (A: 0x1E0, B: 0x2CC, C: 0x3B8) . . . . . . . . . . . .95
Fundamental Apparent Energy, Phase X = A/B/C (X.APPF) (A: 0x1E4, B: 0x2D0, C: 0x3BC) . . . . . . . . . . . .95
Checksum (CHKSUM) (0x066) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Measurements—Virtual Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Fundamental Real Power, Phase A/B/C/T (PWRPF.X) (A: 0x881, B: 0x882, C: 0x884, T: 0x887) . . . . . . . . . . . . .97
Fundamental Reactive Power, Phase A/B/C/T (PWRQF.X) (A: 0x891, B: 0x892, C: 0x894, T: 0x897) . . . . . . . . .97
Fundamental Apparent Power, Phase A/B/C/T (PWRSF.X) (A: 0x8A1, B: 0x8A2, C: 0x8A4, T: 0x8A7) . . . . . . . .98
Fundamental Real Energy, Phase A/B/C/T (ENRPF.X) (A: 0x8E1, B: 0x8E2, C: 0x8E4, T: 0x8E7) . . . . . . . . . . . .98
Fundamental Reactive Energy, Phase A/B/C/T (ENRQF.X) (A: 0x8F1, B: 0x8F2, C: 0x8F4, T: 0x8F7) . . . . . . . . .98
Fundamental Apparent Energy, Phase A/B/C/T (ENRSF.X) (A: 0x8B1, B: 0x8B2, C: 0x8B4, T: 0x8B7) . . . . . . . .99
Current Total Harmonic Distortion Plus Noise, Phase A/B/C (THDN.X) (A: 0x859, B:0x85A, C: 0x85C) . . . . . . .99
Phasors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Phase B Phasor (VBPH: 0x852) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Phase C Phasor (VCPH: 0x854) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
_______________________________________________________________________________________
7
MAXQ3183
TABLE OF CONTENTS (continued)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
TABLE OF CONTENTS (continued)
Harmonics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
RMS Voltage, Harmonic (V.HARM) (0x830) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
RMS Current, Harmonic/Neutral (I.N, I.HARM) (0x840) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Ratio of Harmonic/Fundamental (HARM_NF) (0x850) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Applications Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Grounds and Bypassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Specific Design Considerations for MAXQ3183-Based Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Typical Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
8
_______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Figure 1. External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 2. Brownout Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 3. Simplified Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 4a. SPI Interface Timing (CKPHA = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 4b. SPI Interface Timing (CKPHA = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 5. Read SPI Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 6. Write SPI Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 7. Flowchart for Reading from MAXQ3183 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Figure 8. Flowchart for Writing to MAXQ3183 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Figure 9. Per Sample Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Figure 10. Computation of RMS Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Figure 11. Phase Compensation for Energy Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Figure 12. Apparent and Reactive Energy Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Figure 13. Sample Voltage Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Figure 14. Sample Current Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Figure 15. Offset Testing Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Figure 16. Phase Offset vs. Input Current Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
LIST OF TABLES
Table 1. Command Format for SPI Register Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 2. Command Format for SPI Register Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 3. RAM Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Table 4. Virtual Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Table 5. Meter Unit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Table 6. Virtual Register Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Table 7. Virtual Registers That Activate Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
_______________________________________________________________________________________
9
MAXQ3183
LIST OF FIGURES
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
ABSOLUTE MAXIMUM RATINGS
Voltage Range on DVDD Relative to DGND .........-0.3V to +4.0V
Voltage Range on AVDD Relative to AGND..........-0.3V to +4.0V
Voltage Range on AGND Relative to DGND .........-0.3V to +0.3V
Voltage Range on AVDD Relative to DVDD ..........-0.3V to +0.3V
Voltage Range on Any Pin Relative to
DGND except VxP, IxN Pins..............................-0.3V to +4.0V
Voltage Range on VxP, IxN Relative to AGND ......-0.3V to +4.0V
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Soldering Temperature .............................Refer to the IPC/
JEDEC J-STD-020 Specification.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
METERING SPECIFICATIONS
(VAVDD = VDVDD = VRST to 3.6V, Current Channel Dynamic Range 1000:1 at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Active Energy Linearity Error
DR 1000:1
0.1
Reactive Energy Linearity Error
DR 1000:1
0.2
%
Apparent Energy Linearity Error
DR 1000:1
0.5
%
%
RMS Voltage Linearity Error
RMS Current Linearity Error
DR 20:1
0.5
DR 500:1
1.0
DR 20:1
0.5
%
%
Line Frequency Error
0.5
%
Power Factor Error
1.0
%
ELECTRICAL CHARACTERISTICS
(VAVDD = VDVDD = VRST to 3.6V, TA = -40°C to +85°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
VRST
3.6
V
POWER-SUPPLY SPECIFICATIONS
Digital Supply Voltage
VDVDD
Power-Fail Interrupt Trip Point
VPFW
Active mode, EPWRF = 1
2.84
3.13
V
Power-Fail Reset Trip Point
VRST
Active mode
2.70
2.99
V
VRST
3.6
V
Analog Supply Voltage
VAVDD
Analog Supply Current
IAVDD
fCLK = 8MHz
0.9
1.8
mA
Digital Supply Current
IDVDD
fCLK = 8MHz
8.5
13
mA
LOWPM = 1 (Note 1)
4.2
Low-Power Measurement Mode
Current
ILOWPM
Stop-Mode Current
0.2
mA
12
μA
DIGITAL I/O SPECIFICATIONS
Input High Voltage
VIH
Input Low Voltage
VIL
Input Hysteresis
Input Leakage
10
VIHYS
IL
0.7 x
VDVDD
V
0.3 x
VDVDD
VDVDD = 3.3V
VIN = DGND or VDVDD, pullup off
500
±0.01
______________________________________________________________________________________
V
mV
±1
μA
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
(VAVDD = VDVDD = VRST to 3.6V, TA = -40°C to +85°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
Input Low Current
IIL
RESET Pullup Resistance
Output High Voltage (Except
RESET)
CONDITIONS
VIN = 0.4V, weak pullup on
RRESET
VOL
TYP
MAX
UNITS
150
200
k
-50
50
I OH = -4mA
VDVDD
- 0.4
I OH = -6mA
VDVDD
- 0.5
VOH
Output Low Voltage
MIN
μA
V
I OL = 4mA
0.4
I OL = 6mA
0.5
V
SYSTEM CLOCK SOURCES
External Clock Input Frequency
0
8.12
MHz
External Clock Input Duty Cycle
45
55
%
8.12
MHz
External HF Crystal Frequency
f SYS
Fundamental mode
XTAL1, XTAL2 Internal Load
Capacitance
16
Internal RC Oscillator Frequency
7.4
7.6
Internal RC Oscillator Accuracy
±2
Internal RC Oscillator Current
50
Internal RC Oscillator Startup
Delay
(Note 1)
pF
8.6
MHz
%
120
0.45
μA
μs
ANALOG-TO-DIGITAL CONVERTER
Input Voltage Range
Common-Mode Bias
0
VCOMM
VREF
1.14
V
V
Offset Error
±2
mV
Offset Error Drift
±8
μV/°C
0.05
%
Gain Error (G = 1)
Spurious-Free Dynamic Range
SFDR
90
dB
Total Harmonic Distortion
THD
90
dB
7
kHz
30
ppm/°C
2.048
V
Input Bandwidth (-3dB)
(Note 1)
INTERNAL VOLTAGE REFERENCE
Temperature Coefficient
Output Voltage
(Note 1)
VREF
INTERNAL TEMPERATURE SENSOR
Temperature Error
+4
°C
f SYS/4
MHz
(Note 1)
-4
ns
ns
SPI SLAVE-MODE INTERFACE TIMING
Maximum SPI Clock Rate
SCLK Input Pulse-Width High
t SCH
(Note 3)
4x
t SYS
SCLK Input Pulse-Width Low
t SCL
(Note 3)
4x
t SYS
______________________________________________________________________________________
11
MAXQ3183
ELECTRICAL CHARACTERISTICS (continued)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDVDD = VRST to 3.6V, TA = -40°C to +85°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
SSEL Low to First SCLK Edge
(Slave Enable)
t SE
Last SCLK Edge to SSEL High
(Slave Disable)
CONDITIONS
MIN
(Note 3)
TYP
MAX
UNITS
4t SYS
ns
t SD
t SYS +
5
ns
MOSI Valid to SCLK Sample
Edge (MOSI Setup)
t SIS
5
ns
SCLK Sample Edge to MOSI
Change (MOSI Hold)
t SIH
t SYS +
5
ns
SCLK Shift Edge to MISO Valid
(MISO Hold)
t SOV
3t SYS
+5
ns
Note 1: Specifications guaranteed by design but not production tested.
Note 2: Specifications to -40°C are guaranteed by design and are not production tested.
Note 3: tSYS = 1/fSYS.
SPI Slave Mode Timing
SHIFT EDGE
SSEL
tSD
SAMPLE EDGE
tSCL
tSCH
SCLK
tSE
tSOV
DATA OUTPUT
tSIS
tSIH
DATA INPUT
12
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
VCOMM
CFP, CFQ
COUNTERS
REF
VREF
V0P
V1P
V2P
I0P
I1P
I2P
INP
I/O
REGISTERS
SPI
ADC
TEMP
SENSE
I/O
REGISTERS
I0N
I1N
I2N
VN
ADC CONTROL,
ELECTRICITY
METERING DSP,
COMMUNICATIONS
MANAGER
I/O
REGISTERS
WATCHDOG
TIMER
RESET
16 x 16
HW MULTIPLY
48-BIT ACCUMULATE
POR/
BROWNOUT
MONITOR
MAXQ3183
I/O
BUFFERS
CFQ
CFP
I/O
BUFFERS
MISO
MOSI
SCLK
SSEL
I/O
BUFFERS
IRQ
HF RC
OSC/8
SYSCLK
ADCCLK
ADC CLOCK
PRESCALER
HF
XTAL
OSC
XTAL1
XTAL2
______________________________________________________________________________________
13
MAXQ3183
Block Diagram
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
MAXQ3183
Pin Description
PIN
NAME
FUNCTION
POWER PINS
17, 22
DVDD
Digital Supply Voltage
25
AVDD
Analog Supply Voltage
18
DGND
Digital Ground
9
AGND
Analog Ground
23
VCOMM
24
VREF
Voltage Bias. This pin can be used to create an input common-mode DC offset for ADC channel
conversions.
Voltage Reference. Reference voltage for the ADC. An external reference voltage can be connected to
this pin when extremely high accuracy is required.
VOLTAGE AND CURRENT PINS
26, 3, 4
V0P, I0P,
I0N
Phase A Voltage and Current Analog Inputs
27, 5, 6
V1P, I1P,
I1N
Phase B Voltage and Current Analog Inputs
28, 7, 8
V2P, I2P,
I2N
Phase C Voltage and Current Analog Inputs
1
VN
Analog Input for Common Voltage
2
INP
Analog Input for Neutral Current
CLOCK PINS
10
XTAL2
11
XTAL1
12
IRQ
Interrupt Request Output. This line is driven low by the device to indicate to the master that an
unmasked interrupt has occurred.
13
SSEL
Slave Select Input. This line is the active-low slave select input for the SPI interface.
14
SCLK
Slave Clock Input. This line is the clock input for the SPI interface.
15
MOSI
Master Out-Slave In Input. This line is used by the master to transmit data to the slave (the
MAXQ3183) over the SPI interface.
16
MISO
Master In-Slave Out Output. This line is used by the MAXQ3183 (the slave) to transmit data back to
the master over the SPI interface.
19
CFP
Pulse Output 1. Configurable to represent energy or RMS voltage or current.
20
CFQ
Pulse Output 2. Configurable to represent energy or RMS voltage or current.
21
14
High-Frequency Crystal Input/Output. When using an external high-frequency crystal, the crystal
oscillator circuit should be connected between XTAL1 and XTAL2. When using an externally driven
clock (EXTCLK = 1), the clock should be input at XTAL1, with XTAL2 left unconnected.
RESET
Active-Low Reset Input/Output. An external master can reset the MAXQ3183 by driving this pin low.
This pin includes a weak pullup resistor to allow for a combination of wired-OR external reset
sources. An RC circuit is not required for power-up, as this function is provided internally. This pin
also acts as a reset output when the source of the reset is internal to the device (power-fail, watchdog
reset, etc.). In this case, the RESET pin is held low by the device until it exits the reset state, then the
RESET pin is released.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The MAXQ3183 contains four major subsections: the
analog front-end, the digital signal processor, the precision pulse generators, and an SPI peripheral for communication to the host processor.
Analog Front-End
The analog front-end (AFE) is an 8-channel analog-todigital converter (ADC). It operates autonomously in the
standard configuration, assigning three channels to
phase A, B, and C voltage; three channels to phase A,
B, and C current; one channel to neutral current; and
the last channel to a temperature sensor.
Each channel also contains a programmable-gain
amplifier capable of providing a gain of 1, 2, 4, 8, 16, or
32 incoming signals. Only the voltage channels permit
gain scaling by the host processor. The MAXQ3183
DSP firmware automatically sets the gain on current
channels.
Digital Signal Processor
The DSP code is permanently embedded in masked
ROM and accepts raw current and voltage samples for
each of three phases and continuously calculates a
host of values including RMS volts, RMS amps, real
energy, reactive energy, apparent energy, fundamental
and harmonic energy, and power factor.
The MAXQ3183 DSP core processes incoming samples from the analog front-end according to user configurations. The host sets these operating parameters
by specifying addresses within the device RAM space.
When a calculation cycle is complete, the results are
placed back into RAM as well. Thus, the DSP core uses
the RAM block as both its input (for operating parameters) and output (for calculation results) medium. See
the SPI Peripheral section for how the host writes operating parameters and reads results from the RAM.
The DSP also calculates certain values such as line frequency and active and reactive powers only when
demanded by the host.
Precision Pulse Generators
The MAXQ3183 includes two precision pulse generators that generate a pulse whenever certain conditions
are met. In the MAXQ3183, many meter quantities can
be selected for conversion to meter pulses including
absolute energy, net energy, reactive energy, voltage,
and current.
The pulse generators are accumulators. On each DSP
cycle, whatever quantity is being measured—real energy, reactive energy, current, or something else—is
added to the pulse accumulator. The pulse accumulator is then tested to determine if the value in the accumulator is greater than the threshold. If it is greater, the
threshold value is subtracted from the accumulator
value and the meter pulse starts.
SPI Peripheral
The SPI controller is a slave-only device that can read
or write any location in the data RAM. Additionally, it
can request data from on-demand registers.
The MAXQ3183 implements a truly full-duplex communication, rather than the pseudo half-duplex mode used
by other SPI peripherals. That is, each time a character
is received by the MAXQ3183, a meaningful character
is returned to the host. Often, this is a protocol character. In this way, the host can be assured that the command has been received and is valid. Optional error
checking can also be enabled to further guarantee
proper operation.
Operating Modes
The MAXQ3183 has two basic modes of operation,
each of which is described in the following sections.
The Initialization Mode is the default mode upon powerup or following reset; entry to and exit from the other
operating modes is only performed as a result of commands sent by the master.
Run Mode
This mode is the normal operating mode for the
MAXQ3183. In this mode, the MAXQ3183 continuously
executes the following operations:
• Scans analog front-end channels and collects raw
voltage and current samples.
• Processes voltage and current samples through DSP
filters as enabled and configured.
• Calculates power, energy, and other required quantities and stores these values in RAM registers.
• Responds to register write and read commands from
the master.
• Outputs power pulses on CFP and CFQ as configured.
• Drives IRQ when an interrupt condition has been
detected and the interrupt is not masked.
Stop Mode
This mode places the MAXQ3183 into a power-saving
state where it consumes the least possible amount of
current. In Stop Mode, all functions are suspended,
including the ADC and power and voltage measurement
and processing. The MAXQ3183 does not respond to
any commands from the master in this operating state.
______________________________________________________________________________________
15
MAXQ3183
Detailed Description
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Entry into Stop Mode only occurs at the request of the
master. To place the MAXQ3183 into Stop Mode, the
master must read the ENTER STOP (0xC02) register.
Once this register has been read, the MAXQ3183
enters Stop Mode immediately, before the transmission
of the final ACK byte by the MAXQ3183.
There are three possible ways to bring the MAXQ3183
back out of Stop Mode.
• Power Cycle. The MAXQ3183 automatically exits
Stop Mode if a power-on reset occurs. Following exit
from Stop Mode, all registers are cleared back to
their default states, and the MAXQ3183 transitions to
Initialization Mode.
• External Reset. The MAXQ3183 exits Stop Mode if
an external reset is triggered by driving RESET low.
Once the RESET pin is released and allowed to
return to a high state, the MAXQ3183 comes out of
reset and goes into Initialization Mode. All registers
are cleared to their default states when exiting Stop
Mode in this manner.
• External Interrupt. Driving the SSEL pin low causes
the MAXQ3183 to exit Stop Mode without undergoing
a reset cycle. When exiting Stop Mode in this manner, all register and configuration settings are
retained, and the MAXQ3183 automatically resumes
electric-metering functions and sample processing.
Note that when the master is communicating with the
MAXQ3183, the SSEL line is normally driven low at the
beginning of each SPI command. This means that if the
master sends an SPI command after the MAXQ3183
enters Stop Mode, the MAXQ3183 automatically exits
Stop Mode.
Reset Sources
There are several different sources that can cause the
MAXQ3183 to undergo a reset cycle. For any type of
hardware reset, the RESET pin is driven low when a
reset occurs.
External Reset
This hardware reset is initiated by an external source
(such as the master controller or a manual pushbutton
press) driving the RESET pin on the MAXQ3183 low.
The RESET line must be held low for at least four cycles
of the currently selected clock for the external reset to
take effect. Once the external reset takes effect, it
remains in effect indefinitely as long as RESET is held
low. Once the external reset has been released, the
MAXQ3183 clears all registers to their default states
and resumes execution in Initialization Mode.
When an external reset occurs outside of Stop Mode,
execution (in Initialization Mode) resumes after four
cycles of the currently selected clock (external high-frequency crystal for Run Mode, 1MHz internal RC oscillator for LOWPM Mode). As the MAXQ3183 enters
Initialization Mode, the LOWPM bit is always cleared
CLOCK
RESET
RESET
SAMPLING
INTERNAL
RESET
BEGIN RUNNING IN INITIALIZATION MODE
Figure 1. External Reset
16
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Power-On Reset
When the MAXQ3183 is first powered up, or when the
power supply, VDVDD, drops below the VRST power-fail
trip point (outside of Stop Mode), the MAXQ3183 is
held in power-on reset. Once the power supply rises
above the V RST level, the power-on reset state is
released and all registers are reset to their defaults and
execution resumes in Initialization Mode. The high-frequency external crystal (LOWPM = 0) is always selected as the clock source following any power-on or
brownout reset.
In Stop Mode brownout detection is disabled, so a
power-on reset does not occur until VDVDD drops to a
lower level (V POR ). From the master’s perspective,
power-on resets and brownout resets both cause the
MAXQ3183 to reset in the same way.
Watchdog Reset
The MAXQ3183 includes a hardware watchdog timer that
is armed and periodically reset automatically during normal operation. Under normal circumstances, the
MAXQ3183 always resets the watchdog timer often
enough to prevent it from expiring. However, if an internal
error of some kind causes the MAXQ3183 to lock up or
enter an endless execution loop, the watchdog timer
expires and triggers an automatic hardware reset. There
is no register flag to indicate to the master that a watchdog reset has occurred, but the RESET line strobes low
briefly.
The watchdog timer does not run during Stop Mode.
Software Reset
The master initiates a software reset by setting the
SWRES (OPMODE0.3) bit to 1. When a software reset
occurs, the MAXQ3183 clears all registers to their
default states and returns to Initialization Mode, in the
BROWNOUT DETECTION
BROWNOUT DETECTION (ALWAYS
ENABLED OUTSIDE OF STOP MODE)
FORCES RESET STATE. POR = 1
BROWNOUT DETECTION DISABLED
DURING STOP MODE.
NO RESET IS GENERATED.
VRST1
BROWNOUT DETECTION DISABLED.
POR LEVEL CAUSES RESET.
VPOR
tPOR
INTERNAL
RESET
STOP MODE
Figure 2. Brownout Reset
______________________________________________________________________________________
17
MAXQ3183
to 0, meaning that the MAXQ3183 always switches to
the high-frequency clock before it begins accepting
commands in Initialization Mode.
When an external reset occurs from Stop Mode, execution (in Initialization Mode) resumes after 128 cycles of
the internal RC oscillator (or approximately 128μs).
same manner as if an external reset had taken place.
Unlike a hardware reset, however, a software reset does
not cause the MAXQ3183 to drive the RESET line low.
Power-Supply Monitoring
In addition to the hardware reset provided by the
power-on reset and brownout reset circuits, the
MAXQ3183 includes the capability to detect a low
power supply on the DVDD pin and alert the master
through the interrupt (IRQ) mechanism before a hardware reset occurs. This function, which is always
enabled outside of Stop Mode, causes the RAM status
register flag PWRF (IRQ_FLAG.0) to be set to 1 whenever V DVDD drops below the V PFW trip point. Once
PWRF has been set to 1 by hardware, it can only be
cleared by the master (or by a system reset). Whenever
PWRF = 1, if the EPWRF interrupt masking bit is also
set to 1, the MAXQ3183 drives IRQ low to signal to the
master that an interrupt condition (in this case, a powerfail warning) exists and requires attention.
Clock Sources
All operations including ADC sampling and SPI communications are synchronized to a single system clock.
This clock can be obtained from any one of three selectable sources, as shown in Figure 3.
External High-Frequency Crystal
The default system clock source for the MAXQ3183 is
an external high-frequency crystal oscillator circuit connected between XTAL1 and XTAL2. When clocked with
an external crystal, a parallel-resonant, AT-cut crystal
oscillating in the fundamental mode is required.
When using a high-frequency crystal, the fundamental
oscillation mode of the crystal operates as inductive
reactance in parallel resonance with external capacitors C1 and C2. The typical values of these external
capacitors vary with the type of crystal being used and
should be selected based on the load capacitance as
suggested by the crystal manufacturer.
Since noise at XTAL1 and XTAL2 can adversely affect
device timing, the crystal and capacitors should always
be placed as close as possible to the XTAL1 and
XTAL2 pins, with connection traces between the crystal
and the device kept as short and direct as possible. In
multiple layer boards, avoid running other high-speed
digital signals underneath the crystal oscillator circuit if
possible, as this could inject unwanted noise into the
clock circuit.
Following power-up or any system reset, the high-frequency clock is automatically selected as the system
clock source. However, before this clock can be used
HF
CRYSTAL
GLITCH-FREE
MUX
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
1MHz
INTERNAL
OSCILLATOR
CLOCK
GENERATION
SYSTEM CLOCK
ENABLE
INT/EXT
XTAL IN
RING IN
EXTCLK
STOPM
POR
WATCHDOG TIMER
CRYSTAL
STARTUP TIMER
RING COUNT
CLK
ENABLE
WATCHDOG RESET
Figure 3. Simplified Clock Sources
18
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
External High-Frequency Clock
Instead of using a crystal oscillator to generate the
high-frequency clock, it is also possible to input a highfrequency clock that has been generated by another
source (such as a digital oscillator IC) directly into the
XTAL1 pin of the MAXQ3183.
To use an external high-frequency clock as the system
clock source, the XTAL1 pin should be used as the
clock input and the XTAL2 pin should be left unconnected. The master should also shut down the internal
crystal oscillator circuit by setting the EXTCLK bit
(OPMODE0.4) to 1. This bit is only cleared by the
MAXQ3183 if a power-on or brownout reset occurs and
is unaffected by other resets.
When using an external high-frequency clock, the clock
signal should be generated by a CMOS driver. If the
clock driver is a TTL gate, its output must be connected
to DVDD through a pullup resistor to ensure that the
correct logic levels are generated. To minimize system
noise in the clock circuitry, the external clock source
must meet the maximum rise and fall times and the
minimum high and low times specified for the clock
source in the Electrical Characteristics table.
Internal RC Oscillator
When the external high-frequency crystal is warming
up, or when the MAXQ3183 is placed into LOWPM
mode, the system clock is sourced from an internal RC
oscillator. This internal oscillator is designed to provide
the system approximately 1MHz, although the exact
frequency varies over temperature and supply voltage.
If no external crystal circuit or high-frequency clock will
be used, the MAXQ3183 can be forced to operate infinitely from the internal oscillator by grounding XTAL1.
This ensures that the crystal warmup count never completes, so the MAXQ3183 runs from the internal oscillator in all active modes.
Master Communications
Before the MAXQ3183 can begin performing electricmetering operations, the master must initialize a number of configuration parameters. Since the MAXQ3183
does not contain internal nonvolatile memory, these
parameters (stored in internal registers) must be set by
the master each time a power-up or reset cycle occurs,
or each time a switch is made between LOWPM Mode
and Run Mode.
The external master communicates with the MAXQ3183
over a standard SPI bus, using commands to read and
write values to internal registers on the MAXQ3183.
These registers include, among many other items:
• Operating mode settings (Stop Mode, LOWPM
Mode, external clock mode, etc.)
• Status and interrupt flags (power-supply failure, overcurrent/overvoltage detection, etc.)
• Masking control for interrupts to determine which
conditions cause IRQ to be driven low
• Configuration settings for analog channel scanning
• Power pulse output configuration
• Filter coefficients and configuration
• Read-only registers containing accumulated power
and energy data
As the MAXQ3183 obtains voltage and current measurements in Run Mode or LOWPM Mode, it accumulates, filters, and performs a number of calculations on
the collected data. Many of these operations (including
the various filtering stages) are configured by settings
in registers written by the master. The output results
can then be read by the master from various read-only
registers in parallel with the ongoing measurement and
processing operations.
SPI Communications Rate and Format
The SPI is an interdevice bus protocol that provides
fast, synchronous, full-duplex communications between
a designated master device and one or more slave
devices. In a MAXQ3183-based design, the
MAXQ3183 would be the slave device connected to a
designated master microcontroller.
The external master initiates all communications transfers. The interrupt request line IRQ, while not technically part of the SPI bus interface, is also used for
master/slave communications because it allows the
MAXQ3183 to notify the master that an interrupt condition exists. Some SPI peripherals sacrifice speed in
favor of simulating a half-duplex operation. This is not
the case with the MAXQ3183; it is truly a full-duplex SPI
slave.
______________________________________________________________________________________
19
MAXQ3183
for system execution, a crystal warmup timer must
count 65,536 cycles of the high-frequency clock. While
this warmup time period is in effect, execution continues using the internal 1MHz oscillator. Once the
65,536-cycle count completes (which requires approximately 8.2ms at 8MHz), the device automatically
switches over to the high-frequency clock. This crystal
warmup timer is also activated upon exit from Stop
Mode, since the high-frequency crystal oscillator is shut
down during Stop Mode.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
During an SPI transfer, data is simultaneously transmitted and received over two serial data lines (MISO and
MOSI) with respect to a single serial shift clock (SCLK).
The polarity and phase of the serial shift clock are the
primary components in defining the SPI data transfer
format. The polarity of the serial clock corresponds to
the idle logic state of the clock line and, therefore, also
defines which clock edge is the active edge. To define
a serial shift clock signal that idles in a logic-low state
(active clock edge = rising), the clock polarity select
(CKPOL; R_SPICF.0) bit should be configured to a 0,
while setting CKPOL = 1 causes the shift clock to idle in
a logic-high state (active clock edge = falling). The
phase of the serial clock selects which edge is used to
sample the serial shift data. The clock phase select
(CKPHA; R_SPICF.1) bit controls whether the active or
SCLK CYCLE #
(FOR REFERENCE)
1
2
3
inactive clock edge is used to latch the data. When
CKPHA is set to a logic 1, data is sampled on the inactive clock edge (clock returning to the idle state). When
CKPHA is set to a logic 0, data is sampled on the active
clock edge (clock transition to the active state).
Together, the CKPOL and CKPHA bits allow four possible SPI data transfer formats.
Transfers over the SPI interface always start with the
most significant bit and end with the least significant
bit. All SPI data transfers to and from the MAXQ3183
are always 8 bits (one byte) in length. The MAXQ3183
SPI interface does not support 16-bit character lengths.
The default format (upon power-up or system reset) for
the MAXQ3183 SPI interface is represented in
Figure 4a (CKPOL = 0; CKPHA = 0). In this format, the
4
5
6
7
8
SCLK (CKPOL = 0)
SCLK (CKPOL = 1)
MOSI
(FROM MASTER)
MSB
MISO
(FROM SLAVE)
MSB
6
5
4
3
2
1
LSB
6
5
4
3
2
1
LSB
4
5
6
7
8
*
SSEL (TO SLAVE)
*NOT DEFINED BUT NORMALLY MSB OF CHARACTER JUST RECEIVED.
Figure 4a. SPI Interface Timing (CKPHA = 0)
SCLK CYCLE #
(FOR REFERENCE)
1
2
3
SCLK (CKPOL = 0)
SCLK (CKPOL = 1)
MOSI
(FROM MASTER)
MISO
(FROM SLAVE)
*
MSB
6
5
4
3
2
1
MSB
6
5
4
3
2
1
LSB
LSB
SSEL (TO SLAVE)
*NOT DEFINED BUT NORMALLY LSB OF PREVIOUSLY TRANSMITTED CHARACTER.
Figure 4b. SPI Interface Timing (CKPHA = 1)
20
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The clock rate used for the SPI interface is determined
by the bus master, since the MAXQ3183 always operates as an SPI slave device. However, the maximum
clock rate is limited by the system clock frequency of
the MAXQ3183. For proper communications operation,
the SPI clock frequency used by the master must be
less than or equal to the MAXQ3183’s clock frequency
divided by 4. For example, when the MAXQ3183 is running at 8MHz, the SPI clock frequency must be 2MHz
or less. And if the MAXQ3183 is running in LOWPM
Mode (or if the crystal is still warming up), the SPI clock
frequency must remain at 250kHz or less for proper
communications operation.
In addition to limiting the overall SPI bus clock rate, the
master must also include a communications delay following each byte transmit/receive cycle. This delay,
which provides the MAXQ3183 with time to process an
ADC sample, should be a minimum of 400 system
clocks. With default settings and running at 8MHz, this
delay time is 50μs. Reducing the system clock frequency to 1MHz (LOWPM mode) would increase this delay
period by a factor of 8 to 400μs.
SPI Communications Protocol
All transactions between the master and the
MAXQ3183 consist of the master writing to or reading
from one of the MAXQ3183’s registers. To the host, the
MAXQ3183 looks like a memory array that consists of
both RAM and ROM. This is because the ROM firmware
in the MAXQ3183 reads its operational parameters from
RAM and places its results in RAM. Consequently, configuring a MAXQ3183 is as simple as performing a
block write to its RAM locations.
Some read-only memory locations in the MAXQ3183
trigger actions within the device to calculate electricitymetering results on the fly. The specific function and
purpose of RAM and virtual ROM locations are given in
the register map. There are several different categories
of internal registers on the MAXQ3183.
• RAM Registers. The values of these registers are
stored in the internal RAM of the MAXQ3183. Some
can be read and written by the master, while others
are read-only. RAM registers are either 2 or 4 bytes
long (16 or 32 bits), although in some registers not all
the bits have defined values. Read/write registers are
generally either status/flag registers (which can be
written by either the MAXQ3183 or the master), configuration registers (which are written by the master
and read by the MAXQ3183 firmware), or data registers (which are read-only and are written by the
MAXQ3183 firmware and read by the master).
• Virtual Registers. These read-only registers are not
stored in RAM; instead, they contain values that are
calculated on the fly by the MAXQ3183 firmware
when the master reads them. These registers are
used by the master to obtain values such as phase
A, B, and C active, reactive, and apparent power;
power factor; and RMS voltage and current, which
are calculated from currently collected data on an
as-needed basis. Most virtual registers are 8 bytes in
length.
• Hardware Registers. These registers control core
functions of the MAXQ3183 including the ADC and
the SPI slave bus controller. Each of these registers
(R_ACFG, R_ADCRATE, R_ADCACQ, R_SPICF, and
OPMODE0 (bit 4, EXTCLK only)) has a register location in RAM that “shadows” the value of the hardware
register. To read from a hardware register, the master must first read from the special command register
UPD_MIR (A00h) to copy the values from the hardware registers to the mirror registers in RAM, and
then the mirror register in RAM can be read. To write
to a hardware register, the master reverses the
process by writing to the mirror RAM register and
then reading from the special command register
UPD_SFR (900h) to copy the values from the mirror
registers to the hardware registers.
• Special Command Registers. These registers
(UPD_SFR and UPD_MIR) do not return meaningful
data when read but instead trigger an operation.
Reading UPD_SFR causes values to be copied from
the mirror registers to hardware, and reading
UPD_MIR causes values to be copied from the hardware to mirror registers.
______________________________________________________________________________________
21
MAXQ3183
SPI clock idle state is low, and data is shifted in and out
on the rising edge of SCLK. Once SPI communication
with the MAXQ3183 has been established, it is possible
to alter the CKPOL and CKPHA format settings (as well
as changing the SSEL signal from active low to active
high) if desired by writing to the R_SPICF mirror register
and then reading from the special command register
UPD_SFR to copy the R_SPICF value into the internal
SPI configuration register.
Whenever the active clock edge is used for sampling
(CKPHA = 0), the transfer cycle must be started with
assertion of the SSEL signal. This requirement means
that the SSEL signal be deasserted and reasserted
between successive transfers. Conversely, when the
inactive edge is used for sampling (CKPHA = 1), the
SSEL signal may remain low through successive
transfers, allowing the active clock edge to signal the
start of a new transfer.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Every defined register on the MAXQ3183 has a 12-bit
address (from 0 to 4095). This address is used when
addressing the register for either a read or write operation. Addresses 0 to 1023 (000h to 3FFh) are used to
address RAM registers. Registers with addresses from
1024 to 4095 (400h to FFFh) are used for virtual registers and special command registers.
Each command consists of a read/write command
code, a data length (1, 2, 4, or 8 bytes), a 12-bit register address, and the specified number of data bytes followed optionally by a cyclic redundancy check (CRC).
Since SPI is a full-duplex interface, the master and
slave must both transmit the same number of bytes during the command. When a multiple-byte register is read
or written (2/4/8 byte length), the least significant byte is
read or written first in the command.
Every transaction begins with the master sending 2
bytes that contain the command (read or write), the
address to access, and the number of bytes to transfer.
Every SPI peripheral must return 1 byte for every byte it
receives. If the master is reading 1 or more bytes from
the MAXQ3183, it must send dummy bytes during the
cycles when it is receiving a multibyte response to a
request, meeting the “send a byte to get a byte” requirement. But the MAXQ3183 could require time to calculate
the result, and thus might not have it ready when the
master sends the dummy byte. For this reason, the
MAXQ3183 always sends zero or more bytes of a NAK
character (0x4E or ASCII ‘N’) followed by an ACK character (0x41, or ASCII ‘A’) before sending the data.
If the master is writing 1 or more bytes, it sends the
data to be written immediately after sending the command. The MAXQ3183 returns ACK (0x41) for each
data byte. It then returns NAK (0x4E) until the write
cycle is complete, after which it returns a final ACK.
Immediately after the final ACK, the MAXQ3183 is
ready to begin the next transaction; there is no need to
wait for any other event. It is not even necessary to toggle SSEL to begin the next transaction. The MAXQ3183
knows that the first transaction is over and is ready for
the next.
If, for whatever reason, it is necessary to reset the communications between the host and the MAXQ3183 (for
Table 1. Command Format for SPI Register Read
BYTE
1st byte
2nd byte
Sync bytes
3rd byte
(1st data byte)
...
Nth byte
(Last data byte)
(N + 1) byte
22
TRANSFERS
BIT
7:6
Command Code:
00 Read
01 Reserved
10 Write
11 Reserved
5:4
Data Length:
00 1 Byte
01 2 Bytes
10 4 Bytes
11 8 Bytes
3:0
MSB portion of data address.
7:0
LSB portion of data address.
Master sends command;
Slave sends 0xC1 byte
Master sends address;
Slave sends 0xC2 byte
Master sends dummy;
Slave sends ACK (0x41) or
NACK (0x4E) byte
7:0
Master sends dummy;
Slave sends data
7:0
...
Master sends dummy;
Slave sends data
Master sends dummy;
Slave sends CRC
DESCRIPTION
Master sends dummy byte; Slave responds with NACK if busy,
or with ACK when processing complete.
Master must receive ACK, then receive data.
Data, LSB
...
...
7:0
Data, MSB
7:0
Optional CRC
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
MAXQ3183
Table 2. Command Format for SPI Register Write
BYTE
1st byte
2nd byte
3rd byte
(1st data byte)
...
TRANSFERS
BIT
7:6
Command code:
00 Read
01 Reserved
10 Write
11 Reserved
5:4
Data Length:
00 1 Byte
01 2 Bytes
10 4 Bytes
11 8 Bytes
3:0
MSB portion of data address.
7:0
LSB portion of data address.
7:0
Data, LSB
Master sends command;
Slave sends 0xC1 byte
Master sends address;
Slave sends 0xC2 byte
Master sends data;
Slave sends ACK (0x41)
...
DESCRIPTION
...
...
Nth byte
(Last data byte)
Master sends data;
Slave sends ACK (0x41)
7:0
Data, MSB
(N + 1) byte
Master sends CRC;
Slave sends ACK (0x41)
7:0
Optional CRC
Sync bytes
Master sends dummy;
Slave sends ACK (0x41) or
NACK (0x4E) byte
7:0
example, if synchronization is lost), the host only needs
to wait for the SPI to time out before restarting communication from the first command byte. SPI timeout count
starts after receiving the first command byte from the
master (after the 8th SPI clock of the first byte). The
count stops and clears after receiving the last byte of a
transaction (after the 8th SPI clock of the last byte).
If the timeout count expires (exceeds COM_TIMO)
before the transaction completes, the MAXQ3183 abandons the unfinished transaction and resets the SPI logic
to be ready for the next transaction. The default SPI
timeout is 360ms.
Optionally, a CRC byte can be appended to each
transaction. For write commands, the CRC byte is sent
by the master, and for read commands the CRC byte is
sent by the MAXQ3183. The CRC mode is enabled
when the CRCEN bit is set to 1 in OPMODE1 register.
Otherwise, the MAXQ3183 assumes no CRC byte is
used. The 8-bit CRC is calculated for all bytes in a
transaction, from the first command byte sent by the
Master sends dummy byte; Slave responds with NACK if busy,
or with ACK when processing complete.
Master must receive ACK before starting the next transaction.
master through the last data byte excluding sync bytes,
using the polynomial P = x8 + x5 + x4 + 1. If the transmitted CRC byte does not match the calculated CRC
byte (for a write command), the MAXQ3183 ignores the
command.
The length of the transfer is defined by the first command byte and the status of the CRCEN bit in the
OPMODE1 register. There is no special synchronization
mechanism provided in this simple protocol. Therefore,
the master is responsible for sending/receiving the correct number of bytes. If the master mistakenly sends
more bytes than are required by the current command,
the extra bytes are either ignored (if the MAXQ3183 is
busy processing the previous command) or are interpreted as the beginning of a new command. If the master sends fewer bytes than are required by the current
command, the MAXQ3183 waits for SPI timeout, then
drops the transaction and resets the communication
channel. The duration of the timeout can be configured
through the COM_TIMO register.
______________________________________________________________________________________
23
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
READING DATA FROM MAXQ3183 THROUGH SPI INTERFACE
SSEL
SCLK
MOSI
00 01
ADDRESS
0xC1
MISO
0xC2
DUMMY
DUMMY
DUMMY
DUMMY
NACK (0x4E)
ACK (0x41)
DATA LSB
DATA MSB
Figure 5. Read SPI Transfer
WRITING DATA TO MAXQ3183 THROUGH SPI INTERFACE
SSEL
SCLK
MOSI
10 01
MISO
ADDRESS
0xC1
0xC2
DATA LSB
DATA MSB
DUMMY
DUMMY
ACK (0x41)
ACK (0x41)
NACK (0x4E)
ACK (0x41)
Figure 6. Write SPI Transfer
Figures 5 and 6 show typical 2-byte reading and writing
transfers (without CRC byte).
Host Software Design
Individual message bytes sent through the SPI are
processed in a software routine contained in the ROM
firmware. For this reason, it is necessary to provide a
delay between successive bytes. This byte spacing
must be no less than 400 system clocks to ensure that
the MAXQ3183 has a chance to read and process the
byte before the arrival of the next one. It is strongly recommended that CRC be enabled for both read and
write to achieve reliable operations.
Register Set
Data and device command and control information are
located in internal registers. Registers range from 8 to 64
bits in length and are divided into RAM-based registers
24
and virtual registers. The RAM-based registers contain
both operating parameters and measurement results.
To read any virtual power registers, the host must first
confirm that the DSPRDY bit of the IRQ_FLAG register
is set, which indicates the last DSP cycle has completed, then proceed to reading all the desired virtual
power registers. For best communication efficiency, it is
recommended to complete reading the virtual power
registers before reading other registers. Virtual power
register reads must be completed within 50% of DSP
cycle time, from the moment DSPRDY bit is set. Do not
forget to clear the DSPRDY bit, otherwise, host software
is not able to detect the completion of the new DSP
cycle. The MAXQ3183 does not clear the bit; it only
sets the bit whenever a DSP cycle processing is completed. Users can clear the bit directly after the confirmation that the bit is set. Clearing the DSPRDY bit does
not affect the DSP processing.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
SPI TIMEOUT (360ms)
SEND COMMAND BYTE 1
SPI TIMEOUT (360ms)
SEND COMMAND BYTE 1
N
N
GET 0xC1?
GET 0xC1?
DELAY > 400 SYSCLK
DELAY > 400 SYSCLK
SEND COMMAND BYTE 2
SEND COMMAND BYTE 2
N
N
GET 0xC2?
GET 0xC2?
DELAY > 400 SYSCLK
DELAY > 400 SYSCLK
SEND DATA BYTE
SEND 0x00
Y
N
N
GET 0x4E?
N
GET 0x41?
Y
GET DATA BYTE
EXIT
DONE?
SEND 0x00
SEND 0x00
DONE?
GET 0x41?
DELAY > 400 SYSCLK
DELAY > 400 SYSCLK
N
MAXQ3183
WRITE MAXQ3183
READ MAXQ3183
N
GET 0x4E?
GET 0x41?
EXIT
Figure 7. Flowchart for Reading from MAXQ3183
Figure 8. Flowchart for Writing to MAXQ3183
The virtual registers contain calculated values derived
from one or more real registers. They are calculated at
the time they are requested, and thus can involve addi-
tional time to return a value. Most virtual registers are 8
bytes in length and are delivered least significant byte
first.
______________________________________________________________________________________
25
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Table 3. RAM Register Map
x0h
0x00
STATUS
x1h
x2h
x3h
x4h
OP
OP
OP
MODE0 MODE1 MODE2
0x01
AUX_CFG
0x02
PLS1_WD
0x03
AVG_C
SYS_KHZ
x5h
x6h
IRQ_FLAG
IRQ_MASK
VOLT_CC
AMP_CC
THR1
HPF_C
0x04
NS
0x05
R_ADCACQ
0x06
TEMP_CC
R_
SPICF
x7h
x8h
x9h
xAh
xBh
xCh
xDh
xEh
xFh
SCAN
_IA
SCAN
_VA
SCAN
_IC
SCAN
_VC
SCAN
_IB
SCAN
_VB
SCAN
_IN
SCAN
_TE
PWR_CC
ENR_CC
PLS2_WD
B0FUND
THR2
REJ_NS
A1FUND
B0HARM
OCLVL
OVLVL
UVLVL
NOLOAD
ISUMLVL
COM_TIMO
ACC_TIMO
ZC_LPF
LINEFR
PLSCFG PLSCFG
1
2
CYCNT
AVG_NS
A1HARM
R_ACFG
R_ADCRATE
I1THR
I2THR
CHKSUM
0x11
N.IRMS
0x12
N.I_GAIN
PHASE A CALIBRATION AND STATUS REGISTERS
0x13
A.I_GAIN
0x14
A.V_GAIN
A.PA1
A.PA2
A.E_GAIN
A.
FLAGS
A.EF_GAIN
A.
MASK
A.OFFS_HI
A.GAIN_LO
A.OFFS_LO
A.PA0
B.I_GAIN
B.V_GAIN
B.PA1
B.PA2
C.E_GAIN
C.EF_GAIN
A.
A.
EOVER EFOVER
PHASE B CALIBRATION AND STATUS REGISTERS
0x21
0x22
0x23
B.E_GAIN
B.
FLAGS
B.EF_GAIN
B.
MASK
B.OFFS_HI
B.GAIN_LO
B.OFFS_LO
B.PA0
B.
B.
EOVER EFOVER
PHASE C CALIBRATION AND STATUS REGISTERS
0x30
0x31
C.I_GAIN
C.OFFS_HI
C.GAIN_LO
C.OFFS_LO
C.PA0
C.V_GAIN
C.PA1
C.PA2
C.
FLAGS
C.
MASK
C.
C.
EOVER EFOVER
0x32
PHASE A MEASUREMENT REGISTERS*
0x1C
0x1D
A.PF
A.ACT
A.VRMS
A.IRMS
A.REA
A.APP
A.ACTF
0x1E
A.REAF
A.APPF
A.EAPOS
A.EANEG
0x1F
A.ERPOS
A.ERNEG
A.ES
A.EAFPOS
0x20
A.EAFNEG
A.ERFPOS
A.ERFNEG
A.ESF
PHASE B MEASUREMENT REGISTERS*
0x2B
B.VRMS
B.IRMS
B.ACT
B.REA
B.APP
B.ACTF
B.REAF
0x2D
B.APPF
B.EAPOS
B.EANEG
B.ERPOS
0x2E
B.ERNEG
B.ES
B.EAFPOS
B.EAFNEG
0x2F
B.ERFPOS
B.ERFNEG
B.ESF
0x2C
B.PF
PHASE C MEASUREMENT REGISTERS*
0x39
0x3A
C.PF
C.VRMS
C.IRMS
C.ACT
C.REA
0x3B
C.APP
C.ACTF
C.REAF
C.APPF
0x3C
C.EAPOS
C.EANEG
C.ERPOS
C.ERNEG
0x3D
C.ES
C.EAFPOS
C.EAFNEG
C.ERFPOS
0x3E
C.ERFNEG
C.ESF
*Read-only.
26
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
x0
x1
x2
x3
x4
x7
0x80
PWRP.A
PWRP.B
PWRP.C
PWRP.T
0x81
PWRQ.A
PWRQ.B
PWRQ.C
PWRQ.T
0x82
PWRS.A
PWRS.B
PWRS.C
PWRS.T
V.C
0x83
V.HARM
V.A
V.B
0x84
I.N, I.HARM
I.A
I.B
I.C
0x85
HARM_NF
VBPH
VCPH
0x86
x9
xA
xC
THDN.A
THDN.B
THDN.C
PF.T
0x87
ENRS.A
ENRS.B
ENRS.C
ENRS.T
0x88
PWRPF.A
PWRPF.B
PWRPF.C
PWRPF.T
0x89
PWRQF.A
PWRQF.B
PWRQF.C
PWRQF.T
0x8A
PWRSF.A
PWRSF.B
PWRSF.C
PWRSF.T
0x8B
ENRSF.A
ENRSF.B
ENRSF.C
ENRSF.T
0x8C
ENRP.A
ENRP.B
ENRP.C
ENRP.T
0x8D
ENRQ.A
ENRQ.B
ENRQ.C
ENRQ.T
0x8E
ENRPF.A
ENRPF.B
ENRPF.C
ENRPF.T
0x8F
ENRQF.A
ENRQF.B
ENRQF.C
ENRQF.T
SPECIAL FUNCTION REGISTERS
0xC0
DSPVER
TEMP_C
ENTER
STOP
ENTER
LOWPM
EXIT
LOWPM
Note: All virtual registers are read-only.
______________________________________________________________________________________
27
MAXQ3183
Table 4. Virtual Register Map
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
RAM-Based Registers
The RAM-based registers contain both operating parameters and measurement results. They are divided into a number of categories that are described in the following sections.
General Operating Registers
Global Status Register (STATUS) (0x000)
Bit:
7
6
5
4
3
2
1
0
Name:
—
CROFF
PORF
WDTR
PHSEQI
PHSEQV
REVCFQ
REVCFP
Reset:
0
0
0
0
0
0
0
0
This register contains bits that reflect the global status of the device.
28
BIT
NAME
7
—
FUNCTION
6
CROFF
5
PORF
When set, the last reset was due to power-on-reset. Host should clear this bit to allow the next POR
detection.
4
WDTR
When set, the last reset was caused by expired watchdog. The bit should be cleared (set to 0) by the
host to allow the next watchdog reset detection.
3
PHSEQI
0 = The sequence of currents presented to the inputs is (-A-B-C-).
1 = The sequence of currents presented to the inputs is (-A-C-B-).
2
PHSEQV
0 = The sequence of voltages presented to the voltage inputs is (-A-B-C-).
1 = The sequence of voltages presented to the voltage inputs is reversed (-A-C-B-).
This bit is meaningful only for connection systems that include all three voltages.
1
REVCFQ
0 = The quantity being output on the CFQ pin is positive (direct).
1 = The quantity being output on the CFQ pin is negative (reverse).
0
REVCFP
0 = The quantity being output on the CFP pin is positive (direct).
1 = The quantity being output on the CFP pin is negative (reverse).
Reserved.
When set, the high-frequency crystal has failed and the MAXQ3183 is operating from its internal ring
oscillator. Under these circumstances, energy accumulation is not accurate and the SPI bus does not
operate at full speed.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
7
6
5
4
3
2
1
0
Name:
—
—
—
EXTCLK
SWRES
DSPDIS
LOWPM
—
Reset:
0
0
0
0
0
0
0
0
BIT
NAME
7:5, 0
—
4
EXTCLK
When set, the high-frequency crystal oscillator is disabled and the XTAL1 pin is configured to be a
clock input for the device. This is used when it is desired to operate multiple devices from the same
clock source for purposes of maintaining synchronization.
3
SWRES
When set, forces the internal software to restart from the reset vector. This has the same effect as a
power-on reset, but does not specifically reset any hardware peripherals. This bit is automatically
cleared after the reset.
2
DSPDIS
When set, disables the signal processing software routines. The CPU continues to run at full speed,
but only to perform supervisory functions (such as servicing the SPI port).
LOWPM
When set, causes the CPU to switch its clock source from the external crystal to an internal ring oscillator
that operates at a nominal frequency of 1MHz. In this mode, the CPU continues to run, but the host must
reconfigure the parameters configured for crystal operation (such as filter settings, timeouts, and pulse
widths).
1
FUNCTION
Reserved.
Operating Mode Register 1 (OPMODE1) (0x002)
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
—
—
CRCEN
POPOL
—
—
Reset:
0
0
0
0
0
0
0
0
BIT
NAME
7:4, 1:0
—
3
CRCEN
If set, a 1-byte CRC is appended to the end of each SPI read and is expected at the end of each SPI
write. See the SPI Communications Protocol section for details about how to use the CRC byte for error
checking on the SPI bus.
POPOL
This bit sets the polarity of the output pulse generators. If clear, the pulse outputs are active low; that
is, they remain in the high state until a pulse event occurs, at which time they switch low for one
pulse-width interval before reverting to the high state. If set, the pulse outputs are active high; that is,
they remain in the low state until a pulse event occurs, at which time they switch to the high state for
one pulse-width interval before reverting to the low state.
2
FUNCTION
Reserved.
______________________________________________________________________________________
29
MAXQ3183
Operating Mode Register 0 (OPMODE0) (0x001)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Operating Mode Register 2 (OPMODE2) (0x003)
Bit:
7
6
5
4
3
Name:
—
DHARA
DFUNA
DFUN
—
Reset:
0
0
0
0
0
BIT
NAME
7, 3
—
6
5
4
2
1
WIRSYS
0
0
Reserved.
DHARA
When set, disables automatic determination of the filter parameters for the harmonic filter coefficient. If
set by the host software, the host must set a value in the A1HARM filter coefficient register to
establish the operating frequency of this filter if harmonic-mode calculations are used. When cleared,
the MAXQ3183 automatically determines the value of the harmonic filter coefficient based on the
measured line frequency and the harmonic-order requested (AUX_CFG.ORDH).
DFUNA
When set, disables automatic determination of the filter parameters for the fundamental-mode filter. If
set by the host software, the host must set a value in the A1FUND filter coefficient register to establish
the operating frequency of this filter if fundamental-mode calculations are used. When clear, the
MAXQ3183 automatically determines the value of the fundamental-mode filter coefficient based on the
measured line frequency.
DFUN
When set, fundamental-mode calculations are disabled. Fundamental-mode calculations provide
information about power and energy that are consumed only at the fundamental line frequency apart
from any harmonics that could be present. Setting this bit disables all fundamental frequency registers
but allows the MAXQ3183 to calculate other parameters at a higher rate. Set this bit when (1)
fundamental mode values do not need to be read, and (2) R_ADCRATE needs to be reduced below its
default value.
WIRSYS
VAB
IA
3P3W Wiring (01)
IC
VCB
30
0
FUNCTION
These bits select the coefficient used in calculating apparent power.
00 = 1-phase, 3-wire (1P3W), or 3-phase, 4-wire (3P4W) (C = 1)
01 = 3-phase, 3-wire (3P3W) (C = 3/2)
10 = three voltages, three currents (3V3A) (C = 3/3)
2:1
0
APPSEL
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
BIT
NAME
FUNCTION
V
IA
3P4W Wiring (00)
N
IB
IC
VB
V
VAB
3V3A (10)
2:1
VAC
IA
IB
WIRSYS
IC
VBC
VAN
IA
1P3W (00)
N
IB
VBN
Selects the mechanism to use for calculating apparent power.
0
APPSEL
0: S = VRMS x IRMS
Apparent power is calculated by multiplying, on a per-DSP cycle basis, the
product of the RMS volts and RMS amps.
1: S = P 2 + Q2
Apparent power is calculated by finding the length of the power vector.
______________________________________________________________________________________
31
MAXQ3183
Operating Mode Register 2 (OPMODE2) (0x003) (continued)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Global Interrupt Registers
Interrupt Request Flag Register (IRQ_FLAG) (0x004)
Bit:
15
14
13
12
11
10
9
8
Name:
DSPOR
DSPRDY
DCHR
DCHA
NOZX
UV
OV
OC
Reset:
0
0
0
0
0
0
0
0
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
—
—
ISUMOVF
EOVF
CHSCH
PWRF
Reset:
0
0
0
0
0
0
0
0
The interrupt request flag register contains bits that indicate the reason the IRQ pin has become active. The active
bit must be cleared by the host to avoid continuing firing of the interrupt by the MAXQ3183.
BIT
32
NAME
FUNCTION
15
DSPOR
When set, the DSP was unable to complete processing one cycle when another cycle was due to
begin. This indicates that the R_ADCRATE is set too low, and that samples are arriving more quickly
than they can be processed. Either increase the value of the R_ADCRATE register or set the DFUN bit
in the OPMODE2 register to disable fundamental frequency calculations to reduce the load on the DSP.
14
DSPRDY
13
DCHR
When set, the direction of reactive energy flow has changed (that is, from capacitive to inductive or
from inductive to capacitive).
12
DCHA
When set, the direction of real energy flow has changed (that is, from toward the load to away from the
load, or from away from the load to toward the load).
11
NOZX
When set, the MAXQ3183 has failed to detect zero crossings on one or more voltage channels in one
complete DSP cycle.
10
UV
When set, the absolute instantaneous voltage level in one or more voltage channels failed to exceed
the trip level set in the UVLVL (Undervoltage Level) register for one DSP cycle.
9
OV
When set, the absolute instantaneous voltage level in one or more voltage channels has exceeded the
trip level set in the OVLVL (Overvoltage Level) register.
8
OC
When set, the absolute instantaneous current in one or more current channels has exceeded the trip
level set in the OCLVL (Overcurrent Level) register.
7:4
—
Reserved.
3
ISUMOVF
2
EOVF
1
CHSCH
0
PWRF
Set when the DSP cycle completes.
When set, the vector sum of currents (3 or 4) exceeds the threshold.
When set, one or more energy accumulators have an MSB overflow condition.
When set, indicates a change of the CHKSUM. The CHKSUM is computed over the configuration and
calibration data. The host should review a change in CHKSUM because any change in the
configuration or calibration data affects the metering operation and accuracy.
When set, a power-supply failure is imminent and the supervisory processor should begin taking steps
to save its state and prepare for a loss of power.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
12
11
10
9
8
Name:
EDSPOR
EDSPRDY
EDCHR
EDCHA
ENOZX
EUV
EOV
EOC
Reset:
0
0
0
0
0
0
0
0
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
—
—
EISUM
EEOVF
ECHSCH
EPWRF
Reset:
0
0
0
0
0
0
0
0
BIT
NAME
15
EDSPOR
14
EDSPRDY
13
EDCHR
When set, the DCHR flag causes the IRQ pin to become active.
12
EDCHA
When set, the DCHA flag causes the IRQ pin to become active.
11
ENOZX
When set, the NOZX flag causes the IRQ pin to become active.
10
EUV
When set, the UV flag causes the IRQ pin to become active.
9
EOV
When set, the OV flag causes the IRQ pin to become active.
8
EOC
7:4
—
3
EISUM
FUNCTION
When set, the DSPOR flag causes the IRQ pin to become active.
When set, the DSPRDY flag causes the IRQ pin to become active.
When set, the OC flag causes the IRQ pin to become active.
Reserved.
2
EEOVF
1
ECHSCH
0
EPWRF
When set, the ISUMOVF flag causes the IRQ pin to become active.
When set, the EOVF flag causes the IRQ pin to become active.
When set, the CHSCH flag enables the IRQ pin to become active.
When set, the PWRF flag causes the IRQ pin to become active.
______________________________________________________________________________________
33
MAXQ3183
Interrupt Mask Register (IRQ_MASK) (0x006)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Meter Pulse Configuration
Pulse Configuration—CFP Output (PLSCFG1) (0x01E)
Bit:
7
6
5
4
3
2
1
0
Name:
QNSEL
PHASEC
PHASEB
PHASEA
Reset:
0x0
0
0
0
This register selects which phases are included in the CFP pulse output and also selects which quantity is accumulated to drive the pulse output.
BIT
34
NAME
FUNCTION
7:3
QNSEL
CFP Pulse Output Source Select. This five-bit field determines what meter value will be accumulated in
each of the phases to produce the CFP pulse output. All other values are reserved.
00000 = Net real energy
00001 = Absolute real energy
00010 = Net reactive energy
00011 = Absolute reactive energy
00100 = Apparent energy
00110 = IRMS
00111 = VRMS
01000 = Real energy delivered to load
01001 = Real energy delivered to line
01010 = Reactive energy, quadrant I
01011 = Reactive energy, quadrant II
01100 = Reactive energy, quadrant III
01101 = Reactive energy, quadrant IV
2
PHASEC
CFP Phase C Inclusion. When this bit is set, phase C is included in CFP pulse generation.
1
PHASEB
CFP Phase B Inclusion. When this bit is set, phase B is included in CFP pulse generation.
0
PHASEA
CFP Phase A Inclusion. When this bit is set, phase A is included in CFP pulse generation.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
2
1
0
Name:
7
6
QNSEL
5
4
3
PHASEC
PHASEB
PHASEA
Reset:
0x0
0
0
0
This register selects which phases are included in the CFQ pulse output and also selects which quantity is accumulated to drive the pulse output.
BIT
NAME
FUNCTION
CFQ Pulse Output Source Select. This five-bit field determines what meter value is accumulated in
each of the phases to produce the CFQ pulse output. All other values are reserved.
00000 = Net real energy
00001 = Absolute real energy
00010 = Net reactive energy
00011 = Absolute reactive energy
00100 = Apparent energy
00110 = IRMS
00111 = VRMS
01000 = Real energy delivered to load
01001 = Real energy delivered to line
01010 = Reactive energy, quadrant I
01011 = Reactive energy, quadrant II
01100 = Reactive energy, quadrant III
01101 = Reactive energy, quadrant IV
7:3
QNSEL
2
PHASEC
CFQ Phase C Inclusion. When this bit is set, phase C is included in CFQ pulse generation.
1
PHASEB
CFQ Phase B Inclusion. When this bit is set, phase B is included in CFQ pulse generation.
0
PHASEA
CFQ Phase A Inclusion. When this bit is set, phase A is included in CFQ pulse generation.
CFP Pulse Width (PLS1_WD) (0x020)
Bit:
15
14
13
12
11
Name:
CFP Pulse-Width High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
CFP Pulse-Width Low Byte
Reset:
0x9C
10
9
8
2
1
0
This register designates the width of the CFP pulse, that is, the duration of the period that the CFP pulse is in the
active state. This value is given in ADC frame times (about 360μs). The default value of 0x9C (156 decimal) provides
a pulse width of about 50ms.
______________________________________________________________________________________
35
MAXQ3183
Pulse Configuration—CFQ Output (PLSCFG2) (0x01F)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
CFP Pulse Threshold (THR1) (0x022)
Bit:
31
30
29
28
27
Name:
THR1 Byte 3
Reset:
0x00
Bit:
23
22
21
20
19
Name:
THR1 Byte 2
Reset:
0x10
Bit:
15
14
13
12
11
Name:
THR1 Byte 1
Reset:
0x00
Bit:
7
6
5
4
3
Name:
THR1 Byte 0
Reset:
0x00
26
25
24
18
17
16
10
9
8
2
1
0
This register designates the threshold of the CFP pulse. This value is used to set the meter constant for the CFP
pulse output. When the CFP pulse accumulator exceeds the value set in this register, the CFP pulse output is activated and the CFP pulse accumulator is reduced by the amount in this register.
CFQ Pulse Width (PLS2_WD) (0x026)
Bit:
15
14
13
12
11
Name:
CFQ Pulse-Width High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
CFQ Pulse-Width Low Byte
Reset:
0x9C
10
9
8
2
1
0
This register designates the width of the CFQ pulse; that is, the duration of the period that the CFQ pulse is in the
active state. This value is given in ADC frame times (about 360μs). The default value of 0x9C (156 decimal) provides
a pulse width of about 50ms.
36
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
31
30
29
28
27
Name:
THR2 Byte 3
Reset:
0x00
Bit:
23
22
21
20
19
Name:
THR2 Byte 2
Reset:
0x10
Bit:
15
14
13
12
11
Name:
THR2 Byte 1
Reset:
0x00
Bit:
7
6
5
4
3
Name:
THR2 Byte 0
Reset:
0x00
26
25
24
18
17
16
10
9
8
2
1
0
This register designates the threshold of the CFQ pulse. This value is used to set the meter constant for the CFQ
pulse output. When the CFQ pulse accumulator exceeds the value set in this register, the CFQ pulse output is activated and the CFQ pulse accumulator is reduced by the amount in this register.
Calibration Registers
Current Gain, Phase X = A/B/C/N (X.I_GAIN) (A: 0x130, B: 0x21C, C: 0x308, N: 0x12E)
Bit:
15
14
13
12
11
Name:
Current Gain Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Current Gain Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains gain coefficient for phase X current channel. The raw values are taken from the selected measurement quantity and scaled by the factor:
X.I _ GAIN
2 14
Note: Bit 15 of this register must be set to zero for correct operation.
______________________________________________________________________________________
37
MAXQ3183
CFQ Pulse Threshold (THR2) (0x028)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Voltage Gain, Phase X = A/B/C (X.V_GAIN) (A: 0x132, B: 0x21E, C: 0x30A)
Bit:
15
14
13
12
11
Name:
Voltage Gain Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Voltage Gain Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains gain coefficient for phase X voltage channel. The raw values are taken from the selected measurement quantity and scaled by the factor:
X.V _ GAIN
2 14
Note: Bit 15 of this register must be set to zero for correct operation.
Energy Gain, Phase X = A/B/C (X.E_GAIN) (A: 0x134, B: 0x220, C: 0x30C)
Bit:
15
14
13
12
11
Name:
Energy Gain Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Energy Gain Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains gain coefficient for phase X energy. The raw values are taken from the selected measurement
quantity and scaled by the factor:
X.E _ GAIN
2 14
Note: Bit 15 of this register must be set to zero for correct operation.
Phase-Angle Compensation, High Range, Phase X = A/B/C (X.PA0)
(A: 0x13E, B: 0x22A, C: 0x316)
Bit:
15
14
13
12
11
Name:
Phase-Angle Offset High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Phase-Angle Offset Low Byte
Reset:
0x00
10
9
8
2
1
0
This signed register contains the angle as a fraction of one radian to add to the measured phase angle when the
measured current is above the value given in I1THR. This signed value ranges from -0.5 radian (at a value of
0x8000) to +(0.5 - 2-16) radian (at a value of 0x7FFF).
38
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
12
11
Name:
Phase-Angle Offset High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Phase-Angle Offset Low Byte
Reset:
0x00
10
9
8
2
1
0
This signed register contains the angle, as a fraction of one radian, to add to the measured phase angle when the
measured current is between the values given in I1THR and I2THR. This signed value ranges from -0.5 radian (at a
value of 0x8000) to +(0.5 - 2-16) radian (at a value of 0x7FFF).
Phase-Angle Compensation, Low Range, Phase X = A/B/C (X.PA2)
(A: 0x142, B: 0x22E, C: 0x31A)
Bit:
15
14
13
12
11
Name:
Phase-Angle Offset High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Phase-Angle Offset Low Byte
Reset:
0x00
10
9
8
2
1
0
This signed register contains the angle, as a fraction of one radian, to add to the measured phase angle when the
measured current is below the value given in I2THR. This signed value ranges from -0.5 radian (at a value of 0x8000)
to +(0.5 - 2-16) radian (at a value of 0x7FFF).
Limit Registers
Overcurrent Level (OCLVL) (0x044)
Bit:
15
14
13
12
11
Name:
Overcurrent Level High Byte
Reset:
0xFF
Bit:
7
6
5
4
3
Name:
Overcurrent Level Low Byte
Reset:
0xFF
10
9
8
2
1
0
This register specifies the fraction of full-scale current that is declared to be an overcurrent condition. When X.IRMS
exceeds this level for one DSP cycle, the OCF flag in the X.FLAGS register is set. If the OCM flag is set in the
X.MASK register, setting the OCF flag will cause the interrupt bit OC to be set in the IRQ_FLAG register. If the interrupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for this
register is 0xFFFF.
______________________________________________________________________________________
39
MAXQ3183
Phase-Angle Compensation, Medium Range, Phase X = A/B/C (X.PA1)
(A: 0x140, B: 0x22C, C: 0x318)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Overvoltage Level (OVLVL) (0x046)
Bit:
15
14
13
12
11
Name:
Overvoltage Level High Byte
Reset:
0xFF
Bit:
7
6
5
4
3
Name:
Overvoltage Level Low Byte
Reset:
0xFF
10
9
8
2
1
0
This register specifies the fraction of full-scale voltage that is declared to be an overvoltage condition. When X.VRMS
exceeds this level for one DSP cycle, the OVF flag in the X.FLAGS register is set. If the OVM flag is set in the
X.MASK register, setting the OVF flag will cause the interrupt bit OV to be set in the IRQ_FLAG register. If the interrupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for this
register is 0xFFFF.
Undervoltage Level (UVLVL) (0x048)
Bit:
15
14
13
12
11
Name:
Undervoltage Level High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Undervoltage Level Low Byte
Reset:
0x00
10
9
8
2
1
0
This register specifies the fraction of full-scale voltage below which an undervoltage condition is declared. When
X.VRMS falls below this level for one DSP cycle, the UVF flag in the X.FLAGS register is set. If the UVM flag is set in
the X.MASK register, setting the UVF flag will cause the interrupt bit UV to be set in the IRQ_FLAG register. If the
interrupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for
this register is 0xFFFF.
No-Load Level (NOLOAD) (0x04A)
Bit:
15
14
13
12
11
Name:
No-Load Level High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
No-Load Level Low Byte
Reset:
0x03
10
9
8
2
1
0
This register specifies the fraction of full-scale current below which a no-load condition is declared. When X.IRMS
falls below this level, the MAXQ3183 no longer accumulates power for phase X. Full scale is represented by
0x10000. The maximum value for this register is 0xFFFF.
40
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
12
11
Name:
Vector Sum Threshold High Byte
Reset:
0xFF
Bit:
7
6
5
4
3
Name:
Vector Sum Threshold Low Byte
Reset:
0xFF
10
9
8
2
1
0
This register specifies the threshold value for the vector sum (of three phase currents or three phase currents plus
the neutral current, configurable in the AUX_CFG register) as a fraction of the full-scale current. When the vector sum
(RMS) value exceeds this threshold value in one DSP cycle, the ISUMOVF flag in the IRQ_FLAG register is set. If the
IRQ_MASK.EISUM bit is set, the interrupt pin is driven active. The host must clear the interrupt flag. Full scale is represented by 0x10000. The maximum value allowed is 0xFFFF.
Phase Status Registers
Interrupt Flags, Phase X = A/B/C (X.FLAGS) (A: 0x144, B: 0x230, C: 0x31C)
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
DCHRF
DCHAF
NOZXF
UVF
OVF
OCF
Reset:
0
0
0
0
0
0
0
0
The X.FLAGS register contains condition flags that relate to the function of phase X (A/B/C) measurements. Once
set, these bits can be cleared only by the host.
BIT
NAME
FUNCTION
7:6
—
5
DCHRF
Reactive Energy Direction Change. Set when the direction of reactive power flow changes (from
capacitive to inductive or from inductive to capacitive). If the DCHRM bit is set, this bit sets the DCHR
flag in the IRQ_FLAG register.
4
DCHAF
Real Energy Direction Change. Set when the direction of real power flow changes (from toward the load
to toward the line, or from toward the line to toward the load). If the DCHAM bit is set, this bit sets the
DCHA flag in the IRQ_FLAG register.
3
NOZXF
No-Zero Crossing. Set when the voltage waveform in phase X fails to exhibit a zero crossing during one
DSP cycle. If the NOZXM bit is set, this bit sets the NOZX flag in the IRQ_FLAG register.
2
UVF
Undervoltage. Set when the RMS voltage in phase X falls below the undervoltage threshold set in
UVLVL. If the UVM bit is set, this bit sets the UV flag in the IRQ_FLAG register.
1
OVF
Overvoltage. Set when the RMS voltage in phase X exceeds the overvoltage threshold set in OVLVL. If
the OVM bit is set, this bit sets the OV flag in the IRQ_FLAG register.
0
OCF
Overcurrent. Set when the RMS current in phase X exceeds the overcurrent threshold set in OCLVL. If
the OCM bit is set, this bit sets the OC flag in the IRQ_FLAG register.
Reserved.
______________________________________________________________________________________
41
MAXQ3183
Current Vector Sum Threshold (ISUMLVL) (0x054)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Interrupt Mask, Phase X = A/B/C (X.MASK) (A: 0x145, B: 0x231, C: 0x31D)
Bit:
7
6
5
4
3
2
1
0
Name:
DIR_R
DIR_A
DCHRM
DCHAM
NOZXM
UVM
OVM
OCM
Reset:
0
0
0
0
0
0
0
0
BIT
NAME
7
DIR_R
Reactive Energy Direction Status
0 = positive
1 = negative
6
DIR_A
Active Energy Direction Status
0 = positive
1 = negative
5
DCHRM
Reactive Energy Direction Change Mask. If set, a change in reactive power direction on phase X
causes the DCHR flag in the IRQ_FLAG register to be set.
4
DCHAM
Real Energy Direction Change Mask. If set, a change in real power direction on phase X causes the
DCHA flag in the IRQ_FLAG register to be set.
3
NOZXM
No-Zero Crossing Mask. If set, a no-zero crossing on phase X causes the NOZX flag in the IRQ_FLAG
register to be set.
2
UVM
Undervoltage Mask. If set, an undervoltage condition on phase X causes the UV flag in the IRQ_FLAG
register to be set.
1
OVM
Overvoltage Mask. If set, an overvoltage condition on phase X causes the OV flag in the IRQ_FLAG
register to be set.
0
OCM
Overcurrent Mask. If set, an overcurrent condition on phase X causes the OC flag in the IRQ_FLAG
register to be set.
FUNCTION
Energy Overflow Flags, Phase X = A/B/C (X.EOVER) (A: 0x146, B: 0x232, C: 0x31E)
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
—
SOV
RNOV
RPOV
ANOV
APOV
Reset:
0
0
0
0
0
0
0
0
These bits indicate that an overflow condition has occurred on an energy accumulator. An overflow condition is not
an error condition. Rather, it simply indicates that the value in the energy accumulator could be smaller than the previous reading due to the overflow in the counter. To obtain the actual energy usage since the previous reading,
0x100000000 must be added to the difference. These bits, once set, can be cleared only by the host.
42
BIT
NAME
7:5
—
FUNCTION
4
SOV
3
RNOV
When set, indicates an overflow condition on the reactive negative energy accumulator.
2
RPOV
When set, indicates an overflow condition on the reactive positive energy accumulator.
1
ANOV
When set, indicates an overflow condition on the real negative energy accumulator.
0
APOV
When set, indicates an overflow condition on the real positive energy accumulator.
Reserved.
When set, indicates an overflow condition on the apparent energy accumulator.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Line Frequency (LINEFR) (0x062)
Bit:
15
14
13
Name:
12
11
10
9
8
2
1
0
Line Frequency High Byte
Reset:
Bit:
7
6
5
Name:
4
3
Line Frequency Low Byte
Reset:
Line frequency, LSB = 0.001Hz.
Power Factor, Phase X = A/B/C (X.PF) (A: 0x1C6, B: 0x2B2, C: 0x39E)
Bit:
15
14
13
12
11
Name:
Power Factor High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Power Factor Low Byte
Reset:
0x00
10
9
8
2
1
0
Power factor of phase A/B/C, LSB = 1/214. Note that the power factors are signed integers, and a negative value
indicates a reversed power flow direction.
RMS Voltage, Phase X = A/B/C (X.VRMS) (A: 0x1C8, B: 0x2B4, C: 0x3A0)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
26
25
24
20
19
18
17
16
10
9
8
2
1
0
RMS Voltage Byte 2
15
14
13
Name:
Bit:
27
RMS Voltage Byte 3
Name:
Bit:
28
12
11
RMS Voltage Byte 1
7
6
5
4
3
RMS Voltage Byte 0
This register provides the raw RMS voltage over the most recent DSP cycle, LSB = VFS/224.
______________________________________________________________________________________
43
MAXQ3183
Measurements
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
RMS Current, Phase X = A/B/C (X.IRMS) (A: 0x1CC, B: 0x2B8, C: 0x3A4)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
RMS Current Byte 2
15
14
13
Name:
Bit:
28
RMS Current Byte 3
12
11
RMS Current Byte 1
7
6
5
Name:
4
3
RMS Current Byte 0
This register provides the raw RMS current over the most recent DSP cycle, LSB = IFS/224.
Energy, Real Positive, Phase X = A/B/C (X.EAPOS)
(A: 0x1E8, B: 0x2D4, C: 0x3C0)
Bit:
31
30
29
Name:
Bit:
22
21
Name:
14
13
Name:
25
24
20
19
18
17
16
12
11
10
9
8
2
1
0
Real Energy Byte 1
7
Name:
26
Real Energy Byte 2
15
Bit:
27
Real Energy Byte 3
23
Bit:
28
6
5
4
3
Real Energy Byte 0
On every DSP cycle, the contents of the X.ACT register are tested, and, if positive, are added to this register. When
this register overflows, the APOV bit in the X.EOVER register is set.
44
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Real Energy Byte 2
15
14
13
Name:
Bit:
28
Real Energy Byte 3
12
11
Real Energy Byte 1
7
6
5
Name:
4
3
Real Energy Byte 0
On every DSP cycle, the contents of the X.ACT register are tested, and, if negative, absolute values are added to
this register. When this register overflows, the ANOV bit in the X.EOVER register is set.
Energy, Reactive Positive, Phase X = A/B/C (X.ERPOS)
(A: 0x1F0, B: 0x2DC, C: 0x3C8)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
Name:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
28
Reactive Energy Byte 3
12
11
Reactive Energy Byte 1
7
6
5
4
3
Reactive Energy Byte 0
On every DSP cycle, the contents of the X.REA register are tested, and, if positive, are added to this register. When
this register overflows, the RPOV bit in the X.EOVER register is set.
______________________________________________________________________________________
45
MAXQ3183
Energy, Real Negative, Phase X = A/B/C (X.EANEG)
(A: 0x1EC, B: 0x2D8, C: 0x3C4)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Energy, Reactive Negative, Phase X = A/B/C (X.ERNEG)
(A: 0x1F4, B: 0x2E0, C: 0x3CC)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
28
Reactive Energy Byte 3
12
11
Reactive Energy Byte 1
7
6
5
Name:
4
3
Reactive Energy Byte 0
On every DSP cycle, the contents of the X.REA register are tested, and, if negative, absolute values are added to
this register. When this register overflows, the RNOV bit in the X.EOVER register is set.
Energy, Apparent, Phase X = A/B/C (X.ES) (A: 0x1F8, B: 0x2E4, C: 0x3D0)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
15
26
25
24
20
19
18
17
16
14
13
12
11
10
9
8
2
1
0
Apparent Energy Byte 1
7
Name:
27
Apparent Energy Byte 2
Name:
Bit:
28
Apparent Energy Byte 3
6
5
4
3
Apparent Energy Byte 0
On every DSP cycle, the contents of the X.APP register are added to this register. When this register overflows, the
SOV bit in the X.EOVER register is set.
46
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Voltage Units Conversion Coefficient (VOLT_CC) (0x014)
Bit:
15
14
13
12
11
10
Name:
Voltage Units Conversion Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Voltage Units Conversion Coefficient Low Byte
Reset:
0x01
9
8
1
0
This register contains the value by which the raw voltage value in each phase (A.VRMS, B.VRMS, and C.VRMS) is
multiplied before being presented to the virtual RMS voltage registers (V.A, V.B, and V.C).
To determine the value of VOLT_CC, a voltage value for the least significant bit (VOLT_LSB) of the V.X registers must
be selected. Typical values might range from 1mV to 1nV. To avoid significant conversion loss, VOLT_LSB should be
chosen such that VOLT_CC is >1000. Once VOLT_LSB is determined, calculate VOLT_CC from the following equation:
VOLT _ CC =
VFS
24
2 × VOLT _ LSB
Current Units Conversion Coefficient (AMP_CC) (0x016)
Bit:
15
14
13
12
11
10
Name:
Current Units Conversion Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Current Units Conversion Coefficient Low Byte
Reset
0x01
9
8
1
0
This register contains the value by which the raw current value in each phase (A.IRMS, B.IRMS, C.IRMS, and
N.IRMS) is multiplied before being presented to the virtual RMS current registers (I.A, I.B, I.C, and I.N). To determine
the value of AMP_CC, a current value for the least significant bit (AMP_LSB) of the I.X registers must be selected.
Typical values might range from 1nA to 10μA. To avoid significant conversion loss, AMP_LSB should be chosen
such that AMP_CC is >1000. Once determined, calculate AMP_CC from the following equation:
AMP _ CC =
IFS
24
2 × AMP _ LSB
______________________________________________________________________________________
47
MAXQ3183
Virtual Register Conversion Coefficients
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Power Units Conversion Coefficient (PWR_CC) (0x018)
Bit:
15
14
13
12
11
10
Name:
Power Units Conversion Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Power Units Conversion Coefficient Low Byte
Reset:
0x01
9
8
1
0
This register contains the value by which the raw power value in each phase is multiplied before being presented to
the virtual power registers. The table below lists the raw power registers and the corresponding virtual registers.
DESCRIPTION
RAW
VIRTUAL
Real power, phase A
A.ACT
PWRP.A
Real power, phase B
B.ACT
PWRP.B
Real power, phase C
C.ACT
PWRP.C
Real power, total
—
PWRP.T
Reactive power, phase A
A.REA
PWRQ.A
Reactive power, phase B
B.REA
PWRQ.B
Reactive power, phase C
C.REA
PWRQ.C
—
PWRQ.T
A.APP
PWRS.A
Reactive power, total
Apparent power, phase A
Apparent power, phase B
B.APP
PWRS.B
Apparent power, phase C
C.APP
PWRS.C
—
PWRS.T
Real power, phase A, fundamental frequency only
A.ACTF
PWRPF.A
Real power, phase B, fundamental frequency only
B.ACTF
PWRPF.B
Real power, phase C, fundamental frequency only
C.ACTF
PWRPF.C
Apparent power, total
Real power, total, fundamental frequency only
Reactive power, phase A, fundamental frequency only
—
PWRPF.T
A.REAF
PWRQF.A
Reactive power, phase B, fundamental frequency only
B.REAF
PWRQF.B
Reactive power, phase C, fundamental frequency only
C.REAF
PWRQF.C
—
PWRQF.T
Apparent power, phase A, fundamental frequency only
A.APPF
PWRSF.A
Apparent power, phase B, fundamental frequency only
B.APPF
PWRSF.B
Apparent power, phase C, fundamental frequency only
C.APPF
PWRSF.C
—
PWRSF.T
Reactive power, total, fundamental frequency only
Apparent power, total, fundamental frequency only
PWR_CC establishes the amount of power represented by one PWR_LSB of the power registers. To avoid significant
conversion loss, PWR_LSB should be chosen such that PWR_CC is > 1000. Calculate the value of PWR_CC according to the following formula:
PWR _ CC =
48
IFS × VFS
32
2 × PWR _ LSB
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
15
14
13
12
11
10
Name:
Energy Units Conversion Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Energy Units Conversion Coefficient Low Byte
Reset:
0x01
9
8
1
0
This register contains the value by which the raw accumulated energy value in each phase is multiplied before being
presented to the virtual energy registers. The table below lists the raw energy accumulators and the corresponding
virtual registers.
DESCRIPTION
RAW
Real energy, phase A, positive direction
A.EAPOS
Real energy, phase A, reverse direction
A.EANEG
Real energy, phase B, positive direction
B.EAPOS
Real energy, phase B, reverse direction
B.EANEG
Real energy, phase C, positive direction
C.EAPOS
Real energy, phase C, reverse direction
C.EANEG
Real energy, total
—
Reactive energy, phase A, positive direction
A.ERPOS
Reactive energy, phase A, reverse direction
A.ERNEG
Reactive energy, phase B, positive direction
B.ERPOS
Reactive energy, phase B, reverse direction
B.ERNEG
Reactive energy, phase C, positive direction
C.ERPOS
Reactive energy, phase C, reverse direction
C.ERNEG
Reactive energy, total
VIRTUAL
ENRP.A*
ENRP.B*
ENRP.C*
ENRP.T
ENRQ.A*
ENRQ.B*
ENRQ.C*
—
ENRQ.T
Apparent energy, phase A
A.ES
ENRS.A
Apparent energy, phase B
B.ES
ENRS.B
Apparent energy, phase C
C.ES
ENRS.C
—
ENRS.T
Apparent energy, total
Real energy, phase A, positive direction, fundamental only
A.EAFPOS
Real energy, phase A, reverse direction, fundamental only
A.EAFNEG
Real energy, phase B, positive direction, fundamental only
B.EAFPOS
Real energy, phase B, reverse direction, fundamental only
B.EAFNEG
Real energy, phase C, positive direction, fundamental only
C.EAFPOS
Real energy, phase C, reverse direction, fundamental only
C.EAFNEG
Real energy, total, fundamental only
—
Reactive energy, phase A, positive direction, fundamental only
A.ERFPOS
Reactive energy, phase A, reverse direction, fundamental only
A.ERFNEG
Reactive energy, phase B, positive direction, fundamental only
B.ERFPOS
Reactive energy, phase B, reverse direction, fundamental only
B.ERFNEG
ENRPF.A*
ENRPF.B*
ENRPF.C*
ENRPF.T
ENRQF.A*
ENRQF.B*
*These registers represent the algebraic sum of the positive and reverse energy in the two “raw” registers noted. Thus, the energy
returned in these virtual registers represents the net energy.
______________________________________________________________________________________
49
MAXQ3183
Energy Units Conversion Coefficient (ENR_CC) (0x01A)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Energy Units Conversion Coefficient (ENR_CC) (0x01A) (continued)
DESCRIPTION
RAW
Reactive energy, phase C, positive direction, fundamental only
C.ERFPOS
Reactive energy, phase C, reverse direction, fundamental only
C.ERFNEG
Reactive energy, total, fundamental only
Apparent energy, phase A, fundamental only
VIRTUAL
ENRQF.C*
—
ENRQF.T
A.ESF
ENRSF.A
Apparent energy, phase B, fundamental only
B.ESF
ENRSF.B
Apparent energy, phase C, fundamental only
C.ESF
ENRSF.C
—
ENRSF.T
Apparent energy, total, fundamental only
*These registers represent the algebraic sum of the positive and reverse energy in the two “raw” registers noted. Thus, the energy
accumulated in these virtual registers represents the net energy.
To avoid significant conversion loss, ENR_LSB should be chosen such that ENR_CC is > 1000. Calculate the value
of ENR_CC according to the following formula:
I × VFS × t FR
ENR _ CC = FS
2 16 × ENR _ LSB
Temperature Conversion Coefficient (TEMP_CC) (0x060)
Bit:
15
14
13
12
11
10
Name:
Temperature Conversion Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Temperature Conversion Coefficient Low Byte
Reset:
0x00
9
8
1
0
This register contains the temperature conversion coefficient that is applied to convert the temperature sensor binary output into degrees Celsius, per the following equation, where RAW_TEMP is the raw temperature sensor output.
T_C = RAW_TEMP x TEMP_CC/216 - 273.15
Note that TEMP_CC should be obtained by calibrating the temperature sensor at the desired operation condition.
Typical approximate value is TEMP_CC = 0x0426. To read temperature, use the special register command 0xC01.
50
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The virtual registers are calculated values derived from one or more real registers. They are calculated at the time
they are requested, and thus could involve additional time to return a value. Most virtual registers are 8 bytes in
length and are delivered least significant byte first.
Power
Real Power, Phase X = A/B/C/T (PWRP.X) (A: 0x801, B: 0x802, C: 0x804, T: 0x807)
This signed register contains the real instantaneous power delivered into phase A/B/C or total. Power is calculated
from the instantaneous energy measurement according to the following equation:
PWRP.X =
X.ACT × PWR _ CC × 2 16
NS
The register is 8 bytes long, but the most significant 2 bytes are not used. See the PWR_CC register description for
more details.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Note that the sign bit is bit 47 for all 8-byte signed virtual registers.
Reactive Power, Phase X = A/B/C/T (PWRQ.X) (A: 0x811, B: 0x812, C: 0x814, T: 0x817)
This signed register contains the reactive instantaneous power delivered into phase A/B/C or total. Power is calculated from the instantaneous energy measurement according to the following equation:
PWRQ.X =
X.REA × PWR _ CC × 2 16
NS
The register is 8 bytes long, but the most signficant 2 bytes are not used. See the PWR_CC register description for
more details.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
______________________________________________________________________________________
51
MAXQ3183
Virtual Registers
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Apparent Power, Phase X = A/B/C/T (PWRS.X) (A: 0x821, B: 0x822, C: 0x824, T: 0x827)
This register contains the apparent instantaneous power delivered into phase A/B/C or total. Power is calculated
from the instantaneous energy measurement according to the following equation:
PWRS.X =
X.APP × PWR _ CC × 2 16
NS
The register is 8 bytes long, but the most significant 2 bytes are not used. See the PWR_CC register description for
more details.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Voltage and Current
RMS Volts, Phase X = A/B/C (V.X) (A: 0x831, B: 0x832, C: 0x834)
This register contains the RMS voltage on phase A/B/C. The units are defined by the VOLT_CC setting such that V.X
= X.VRMS x VOLT_CC. In this equation, VOLT_CC is the conversion coefficient. See the VOLT_CC register for more
information.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
RMS Amps, Phase X = A/B/C/N (I.X) (A: 0x841, B: 0x842, C: 0x844, N: 0x840)
This register contains the RMS current on phase A/B/C or the neutral channel. The units are defined by the AMP_CC
setting such that I.X = X.IRMS x AMP_CC. In this equation, AMP_CC is the conversion coefficient. See the AMP_CC
register for more information.
52
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
This signed register contains the power factor of the total power. The power factor is calculated as:
PF.T =
A.ACT + B.ACT + C.ACT
A.APP + B.APP + C.APP
It is expressed in units of 0.00001; thus, unity power factor is expressed as decimal 100,000
(0x00000000000186A0). This register is presented as a two’s complement value, so that a load delivering real power
to the line (that is, reverse power) is seen as having a power factor of -1 (0x0000FFFFFFFE7960).
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Energy
Real Energy, Phase A/B/C/T (ENRP.X) (A: 0x8C1, B: 0x8C2, C: 0x8C4, T: 0x8C7)
This signed register contains the real accumulated energy delivered into phase A/B/C or total. The register is calculated according to the following formula:
ENRP.X = ENR_CC x (X.EAPOS - X.EANEG)
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Reactive Energy, Phase A/B/C/T (ENRQ.X) (A: 0x8D1, B: 0x8D2, C: 0x8D4, T: 0x8D7)
This signed register contains the reactive accumulated energy delivered into phase A/B/C or total. The register is
calculated according to the following formula:
ENRQ.X = ENR_CC x (X.ERPOS - X.ERNEG)
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Apparent Energy, Phase A/B/C/T (ENRS.X) (A: 0x871, B: 0x872, C: 0x874, T: 0x877)
This register contains the apparent accumulated energy delivered into phase A/B/C or total. The register is the product of the ENR_CC and X.ES registers.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
______________________________________________________________________________________
53
MAXQ3183
Power Factor
Power Factor (PF.T) (0x867)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Theory of Operation
Analog Front-End Operation
Whenever the MAXQ3183 is in one of the active operating modes (Run Mode or LOWPM Mode), the analog
front-end operates continuously, scanning up to eight
scan slots depending on the selected front-end configuration. For each analog scan slot that is enabled, one
of the eight differential input pairs is measured.
The SCAN_IX and SCAN_VX (X = A/B/C), SCAN_IN,
and SCAN_TE registers contain the settings for each
slot, which include whether the slot is enabled and the
differential input pair to measure during that scan slot.
The logical mapping of the slots is fixed in following
order:
• Slot 0—Phase A Current (IA)
• Slot 1—Phase A Voltage (VA)
•
•
•
•
Slot 2—Phase C Current (IC)
Slot 3—Phase C Voltage (VC)
Slot 4—Phase B Current (IB)
Slot 5—Phase B Voltage (VB)
• Slot 6—Neutral Current (IN)—disabled by default
• Slot 7—Temperature Measurement—disabled by
default
The required time for each analog scan slot measurement (t C ) is determined by the MAXQ3183 system
clock frequency and the setting of the R_ADCRATE
hardware register, as shown below:
tC = 1/fCLK x (R_ADCRATE[8:0] + 1)
Using the default register settings (R_ADCRATE = 167h
= 359d), the time for each analog slot measurement
(tC) is 45μs when the MAXQ3183 is running at 8MHz.
Since there are eight analog scan slots in the measurement frame, the total time for all measurements (tFR) is
tC x 8. Using the default settings with the MAXQ3183
running at 8MHz, the entire sequence of measurements
takes 360μs to complete, which, in turn, means that
360μs will elapse, for example, between one phase A
current measurement and the next.
Even if some of the analog measurement slots (such as
neutral current or temperature measurement) are
skipped by setting the DADCNV bit in that slot’s register to 1, the time period for that slot will remain in the
frame, ensuring that the total frame time is always tC x
8, regardless of which individual slots are enabled or
disabled.
54
Digital Signal Processing (DSP)
Terminology
Establishing the precise definitions of some of the terms
used in this document will assist in understanding how
the DSP functions.
Sample Period: The amount of time required to measure a single data element; 45μs, by default.
ADC Frame Period: The amount of time required for
the ADC to sample all analog inputs; always equal to 8
sample periods. The inverse of this value is the frame
rate; by default 2778 samples per second. This is the
rate at which any particular signal is sampled by the
MAXQ3183.
Line Cycle: The period of time from one positive-going
zero crossing on a voltage channel to the next positivegoing zero crossing. At 50Hz, this is nominally 20ms; at
60Hz, this is nominally 16.67ms.
Cycle Count: The number of line cycles contained in a
single DSP cycle. An integer, this is typically set to
some value greater than one to minimize the effect of
load variations that may not occur in every line cycle.
By default, this value is 16.
DSP Cycle: The period of time over which line parameters are calculated. Energy and other parameters are
accumulated once per DSP cycle. One DSP cycle is
the time of a line cycle multiplied by the cycle count.
NS: This value represents the number of ADC frame
periods in a DSP cycle. This is a noninteger calculated
value. For example, if the cycle count is set to unity,
and the line frequency is exactly 50Hz, the NS value
would be 20ms/360μs = 55.6.
Digital Processing
As voltage and current samples are collected, the
MAXQ3183 performs a variety of digital filtering,
accumulation, and processing calculations to arrive at
meter-reading values (such as line frequency, RMS
voltage and current, and active and reactive power)
that can then be read by the master. The MAXQ3183
calculates and detects values and conditions including
the following:
• Zero-crossing detection
• Line frequency and line period calculation
• RMS voltage (phase A, phase B, phase C)
• RMS current (phase A, phase B, phase C, neutral
current)
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
• Energy accumulation (including energy pulse output
function)
• Overvoltage detection
• Overcurrent detection
Per DSP Cycle Operations
At the end of each DSP cycle, accumulated information
is available that is used to calculate all other operational results in the meter. DSP cycles track the line frequency and have a duration of the number of cycles
specified in the CYCNT register. On each phase, the
time required for CYCNT cycles to complete is calculated and this value is used to update the duration of one
DSP cycle, specified in the NS register.
NS contains the number of ADC frame periods in a single DSP cycle. Because line frequency varies slightly
from cycle to cycle, and because the ADC frame clock
is not synchronized to the line, the value of NS is not an
integer, and varies slightly from DSP cycle to DSP cycle.
• Undervoltage detection
Per Sample Operations
On every ADC frame, the input samples are processed
as follows:
• The voltage and current samples are read. The current sample is shifted to account for the gain applied
in the PGA. The phase- and gain-corrected samples
are passed to the next stage.
• Both the current and voltage signals are passed
through highpass filters (HPF) specified by the
HPF_C variable.
• The current and voltage signals are now split into
several components. The first of these components is
squared and accumulated to begin the RMS current
and voltage process. The second is processed and
accumulated to begin the real/reactive power calculation. And a third is processed through a peak filter
(specified by B0FUND and A1FUND registers) and
then accumulated to provide information for the fundamental frequency power calculations.
The result is a set of accumulated values that represent
squared voltage, squared current, and real (active) and
reactive (P and Q) energies for both the entire usable
spectrum and as filtered by the peak filter. The real and
Because the value of NS is so critical to accurate calculation of energy, ensuring that it is correct on every
cycle is essential. There are two ways to manage the
slight variation of NS from cycle to cycle: first, one
could simply replace the old value of NS with the newly
calculated value on each DSP cycle. This means that
NS (and every other value in the meter, since they
depend on NS) would have a significant amount of
uncertainty. A better method is to use each newly calculated value of NS as an input to a filter. The output of
the filter is then the value of NS that is actually used in
calculations. In the MAXQ3183, this filter is controlled
by the AVG_NS register.
X2
HPF
ADC
V_GAIN
VOLTAGE INPUT
BPF
ENERGY PROCESSING
CURRENT INPUT
I_GAIN
ADC
EP
EQ
ENERGY PROCESSING
GAIN SEL
I2
EPF
EQF
BPF
HPF
X2
V2
Figure 9. Per Sample Operations
______________________________________________________________________________________
55
MAXQ3183
imaginary components of energy at this point do not yet
represent real and reactive power; to obtain usable
power values further processing is required. Each of
these values is further processed at the end of each
DSP cycle.
• Power (active, reactive, and apparent) for each
phase
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
A second problem with updating NS on every line
cycles is the fact that noise impulses that occur at nearly the same time as the zero crossing can shift the zero
crossing, affecting the accuracy of the energy measured during the preceding period. For this reason, a
second register, REJ_NS contains a value that specifies
how far a particular sample can deviate from the average and still be considered valid. If the period of the
newly acquired DSP cycle differs from the previously
accumulated average value by more than REJ_NS ADC
frames, NS is not updated with the new period (but the
energy is still accumulated).
With this discussion in mind, the signal path for the various reported parameters can be reviewed.
RMS Volts and RMS Amps: First, the squared voltage
accumulation is divided by NS. This accomplishes the
“mean” part of the “root-mean-square” calculation.
Then, the square root of the result is taken, producing
the raw RMS calculation value.
On the voltage channel, the signal is ready for gain
compensation to be applied. But on the current channel,
there is an additional twist: depending on the amplitude
of the current, there may be a gain factor pre-applied
before the raw sample is available. To compensate for
inaccuracy in the gain factor for the amplifier and for
noise seen in the channel at high gain settings, it may
be necessary to provide linearity compensation.
There are three registers that manage the linearization
of the current signal: the X.OFFS_HI (X = A/B/C) register contains a signed value that is added to the raw
RMS current signal before further processing; the
X.OFFS_LO register contains a signed value that is
I2
added to the raw RMS current signal when the current
signal is below a low current threshold (1/32 of the full
scale) value; and the X.GAIN_LO register contains a
gain adjustment that is applied to the current signal
when the current signal is below the threshold value.
The practical effect of this is to turn what may be a
somewhat nonlinear response curve for the current sensor to a much more linear response by two-piece
approximation.
The “high current” calibration term X.OFFS_HI is used
so long as the instantaneous current exceeds the lowcurrent threshold at some instant during a DSP cycle. As
long as this threshold is crossed during a DSP cycle, the
value in X.OFFS_HI controls the offset current.
When the input stays below the low-current threshold
for one DSP cycle, the X.OFFS_LO and X.GAIN_LO are
applied. The low-current calibration terms (X.GAIN_LO
and X.OFFS_LO) remain in effect until the peak of input
current waveform exceeds 1/32 of full-scale current at
any time during a DSP cycle.
As a final step, both voltage and current are passed
through an averaging filter that provides smoothing for
the signals. The amount of filtering is given in AVG_C.
Energy: The per-sample processing produces a pair of
digital signals that represent the complex energy signal. From this complex signal, it is desired to extract the
real portion and the reactive portion. At first glance, this
seems trivial: the real portion is the real part of the complex signal, and the reactive portion is the imaginary
part of the complex signal. Apparent power (in voltamperes) is the magnitude of the complex signal, and
power angle is the argument of the complex signal.
OFFS_HI
GAIN_LO
OFFS_LO
AVG_C
LINEARIZATION
AVERAGE
NS
IRMS
RAW_I
RAW_V
V2
AVERAGE
NS
VRMS
AVG_C
Figure 10. Computation of RMS Values
56
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
⎧PA0, IRMS ≥ I1THR
⎫
⎪
⎪
PA = ⎨PA1, I1THR > IRMS ≥ I2THR) ⎬
⎪PA2, I
⎪
RMS < I2THR
⎩
⎭
To use a constant phase compensation, set I1THR and
I2THR to zero and insert the phase compensation value
into PA0.
The same processing can be performed to calculate
the reactive energy value. But reactive energy can be
calculated in another way: calculate apparent energy
by multiplying the raw RMS volts and raw RMS current,
square this value, then subtract the squared real
power. The square root of this value is the reactive
energy.
Similarly, apparent energy can be calculated in either
of two ways: either as the product of the raw RMS volts
and amps, or as the square root of the sum of the
squares of the real and reactive energy. Which of these
is selected depends on the value of the APPSEL bit in
the OPMODE2 register: if 0, then apparent energy is
the product of the raw RMS volts and amps and reactive energy is calculated using the difference of
squares method; if 1, apparent energy is calculated
using the sum of squares method and reactive energy
is calculated directly from the complex energy.
Line Frequency and Phasor Angles: Line frequency
can be taken directly from the NS value. Recall that NS
is the number of frames in a DSP cycle. Since each
frame is 360μs, simply multiply NS by 360μs and divide
by CYCNT to obtain the line period. The reciprocal of
this is the line frequency.
To calculate phasor angles, the numbers of samples
between zero crossings on phase A and B and on phase
A and C are taken. Since NS is the number of samples
during a complete DSP cycle, it is easy to calculate the
fraction of a complete cycle. The software then converts
this value to degrees and adjusts it such that no negative
angles are reported. No calibration is required for line
frequency and phasor angle calculation.
Energy Accumulation
Once real and reactive energy over the most recent
DSP cycle has been calculated, it is necessary to accumulate the result.
For reactive energy, the result accumulated during any
DSP cycle may be positive (for an inductive load) or
EP
EQ
REAL/REACTIVE
PROCESSING
OFFS_HI
GAIN_LO
OFFS_LO
PA0
PA1
PA2
PHASE
COMPENSATION
LINEARIZATION
OFFS_HI
GAIN_LO
OFFS_LO
LINEARIZATION
E_GAIN
AVG_C
AVERAGE
EREAL
E_RAWREAL
E_RAWREACTIVE
Figure 11. Phase Compensation for Energy Calculations
______________________________________________________________________________________
57
MAXQ3183
But current sensors and other external circuitry components introduce a phase distortion to the current signal,
and this phase distortion may not be constant at all current values. Consequently, for the most precise measurements, the phase between the voltage and current
signals must be compensated. In the MAXQ3183, the
energy signals are compensated for phase offset by
performing a complex multiplication of the signal with
the contents of the appropriate phase offset register.
Determining which phase offset register is appropriate is
a matter of comparing the incoming RMS current for the
phase with the contents of the I1THR and I2THR registers. It is the responsibility of the administrative software
to ensure that I1THR is greater than or equal to I2THR. If
the raw RMS current is greater than or equal to the contents of I1THR, then the angle expressed in PA0 is used
to compensate the phase angle. If the raw RMS current
is less than I2THR, then the angle expressed in PA2 is
used to compensate the phase angle. And if the raw
RMS current falls between I1THR and I2THR then PA1 is
used to compensate the phase angle. In this way, a
three-piece stepwise approximation of the phase
response of the current sensor is available.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
E_RAWREAL
E_RAWREACTIVE
RAW_I
RAW_V
E_GAIN
X2 + Y2
AVG_C
AVERAGE
EAPPARENT
AVERAGE
EREACTIVE
X×Y
APPSEL
E_GAIN
X2 - Y2
AVG_C
APPSEL
Figure 12. Apparent and Reactive Energy Calculations
negative (for a capacitive load). These values are separately accumulated. This means that during any one
DSP cycle, only positive or negative reactive energy will
be accumulated.
Similarly, for real energy, the result accumulated during
any DSP cycle can be positive (that is, energy is delivered to the load) or negative (that is, energy is driven
back into the line). As is performed for reactive energy,
these values are separately accumulated.
Apparent energy is also accumulated, but since this
value is always positive or zero, there is only one
apparent energy accumulator.
From time to time, the accumulators generate an overflow. When this occurs, the appropriate bit is set in the
overflow status register X.EOVER.
When an overflow occurs, supervisory code running on
the host processor must make the appropriate adjustments in the reported energy. In many cases, this could
simply involve incrementing an overflow counter. The
host processor must then clear the overflow indication.
No-Zero-Crossing Detection
The MAXQ3183 monitors the voltage signal on each
phase for zero-crossing events. If no ascending zero
crossings are detected within a DSP cycle, the NOZXF
(X.FLAGS) flag is set by the MAXQ3183 to notify the
master of this condition. If the NOZXM bit is set, this
flag sets the NOZX bit in the IRQ_FLAG. If the interrupt
enable bit ENOZX is set to 1, the interrupt signal IRQ is
driven low by the MAXQ3183 whenever NOZX = 1. The
master can clear NOZXF and NOZX back to 0 to
remove the interrupt condition.
58
Phase Sequence Status
Phase sequence status bits PHSEQV and PHSEQI indicate the order in which zero crossings are detected.
When a zero-crossing event occurs on the phase A signal, followed by phase B, phase C, and then phase A
again, this bit cleared. If a zero crossing on phase A is
then followed by a zero crossing on phase C, then
phase B, this bit set to 1.
RMS Voltage, RMS Current, and Energy
Calculation
For each of the three phases, the MAXQ3183 calculates RMS voltage and RMS current values, as well as
determines active and reactive energy, using a linecycle-based integration process.
Power Calculation (Active, Reactive,
Apparent)
The power, energy, and RMS calculation process consists of two tasks: continuous accumulation and postprocessing triggered every CYCNT line cycles. The
accumulation task accumulates raw data obtained
from the AFE during CYCNT line cycles. This task is
performed continuously in the background by the
MAXQ3183. When a CYCNT line cycles accumulation
stage has completed, which is determined by a dedicated frame counter exceeding the NS level, the raw
integral accumulator values are saved for postprocessing and cleared, beginning the next cycle of accumulation task. Then, the DSP postprocessing is triggered
to process saved integrals and calculate energy,
power, etc., values. Note that the background accumulation task continues while foreground postprocessing
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The MAXQ3183 accumulates raw sums and calculates
line-cycle integrals for each voltage-current pair separately. The individual power accumulators are:
• PA = VA x IA
• PB = IB x VB or -IB x VC or -IB x (VA + VC) or -IB x
(VA - VC)
• PC = VC x IC
The PA and PC accumulators always operate in a single mode: (VA x IA) for the PA accumulator, (VC x IC) for
the PC accumulator. Alternately, the operating mode of
the PB accumulator is defined by setting the CONCFG[1:0] bits in the OPMODE1 register.
Energy Accumulation Start Delay
All filters have a certain settling time before accurate
energy readings can be accumulated. To avoid accumulation of invalid data from filters that are still settling,
an energy accumulation timeout period can be set in
the ACC_TIMO register. When ACC_TIMO > 0, computed energy is not accumulated for ACC_TIMO of DSP
cycles. The MAXQ3183 will decrement the ACC_TIMO
register every DSP cycle until it becomes 0. When
ACC_TIMO reaches 0 value, energy accumulation
begins (or resumes, if ACC_TIMO was set to nonzero
value by the master). Pulse outputs are also disabled
when ACC_TIMO > 0. The default value of ACC_TIMO
is 0x05.
No-Load Feature
To avoid “meter creep,” no energy accumulation should
take place when measured current is less than a certain threshold. The NOLOAD register can be programmed to enable and configure this feature. If the
measured X.IRMS value for a phase (A, B, or C) falls
below the NOLOAD threshold, the energy accumulators
for this phase are not incremented. Setting NOLOAD =
0 disables this feature. Full scale is represented by
0x10000.
On Demand Calculations
So far in this discussion, the values being calculated
and managed in the MAXQ3183 have been based on
fundamental units meaningful to the device itself: voltage as a binary fraction of full-scale voltage; current as
a binary fraction of full-scale current, and time as a noninteger multiple of the ADC frame time.
But a practical electricity meter must report its results in
standard units, such as volts, amperes, and watts. The
MAXQ3183 contains a mechanism to convert the internal units (“meter units”) to real world units (“display
units”). This conversion is performed in the conversion
constant (CC) registers.
For some of these values (voltage, current) the calculation is simple: multiply by the conversion constant. For
other values (power, energy) the calculation is more
complex. In any case, the value in the CC register
affects only the conversion from a meter unit to a display unit; calibration is handled separately in the gain
adjustment registers for each recorded value.
The results of all on-demand calculations are reported
as 8-byte (64-bit) values of which no more than 6 bytes
(48 bits) are significant. Eight bytes are used as a common length; however, fewer bytes can be requested for
those registers known to have smaller maximum values.
For example, the power factor virtual register has a
maximum value that is expressed in only 3 bytes; consequently, the register can be requested with a length
of 4 bytes without loss of data.
RMS Volts, RMS Amps
These registers (V.A, V.B, V.C, I.A, I.B, I.C) are calculated by simply multiplying the calculated RMS value
(A.VRMS, B.VRMS, C.VRMS, A.IRMS, B.IRMS, C.IRMS)
by the contents of the VOLT_CC or AMP_CC register.
Since the RMS voltage and RMS current are given in
32-bit registers and the conversion coefficients are
given in 16-bit registers, the result of the product is 48
bits.
Regardless of the internal units used, VOLT_CC and
AMP_CC can be tailored so that the LSB of the virtual
register can be any value. For example, if one wished
to have a 32-bit value representing milliamps, one
could multiply by a value that scaled the register such
that the LSB was 2-16mA. Then, discard the low-order
16 bits. The result is milliamps with 32 bits of precision;
thus, the maximum current that could be represented
would be 4,294,967,296mA, or just over 4MA.
______________________________________________________________________________________
59
MAXQ3183
is taking place, i.e., both tasks are executed simultaneously sharing CPU time. It is essential that the DSP
postprocessing calculations be completed before the
next DSP trigger to avoid losing accumulated data.
The master should allow enough processing time by
adjusting the R_ADCRATE register. Default settings
provide plenty of CPU time for both tasks.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The VOLT_CC and AMP_CC values can be calculated
from the full-scale voltage or full-scale current and the
desired value of one LSB in the display register:
AMP _ CC =
VOLT _ CC =
IFS
2 24 × AMP _ LSB
VFS
24
2 × VOLT _ LSB
Example: Assume the full-scale current is 102.4A, and
that we desire a 1nA LSB. The calculation would provide an AMP_CC value of:
102.4/(224 x 10-9) = 6104 = 0x17D8
Power
The MAXQ3183 measures energy. But power is just
energy per unit time, and the MAXQ3183 keeps track of
the time unit over which energy is accumulated. This is
simply the NS value, the fractional number of samples
that comprises one DSP cycle. So converting energy to
power is as simple as dividing the accumulated energy
over one DSP cycle by NS. Multiplying by a conversion
constant (PWR_CC) gives power in user-established
units.
The power registers (PWRP.A, PWRP.B, PWRP.C,
PWRQ.A, PWRQ.B, PWRQ.C, PWRS.A, PWRS.B,
PWRS.C) are calculated by multiplying the accumulated energy (A.ACT, A.REA, A.APP, B.ACT, B.REA,
B.APP, C.ACT, C.REA, C.APP) by the conversion coefficient (PWR_CC) and then dividing by NS. The result is
the 48-bit average power over the most recent DSP
cycle, in units established by the conversion coefficient.
The PWR_CC value can be calculated from the fullscale voltage, the full-scale current, and the desired
value of one LSB in the display register:
PWR _ CC =
IFS × VFS
2 32 × PWR _ LSB
Example: For this example, assume the full-scale current is 102.4A, the full-scale voltage is 558.1V, and that
the desired LSB is milliwatts after discarding the 16
LSB; that is, the desired LSB is 2-16 milliwatts. Perform
the following calculation:
102.4 x 558.1/(232 x 2-16 x 10-3) = 872 = 0x0368
Power Factor
Power factor is calculated as real power divided by
apparent power. But note that apparent power can be
calculated in either of two ways: either as a square root
of the sum of the squares of the real and reactive
power, or more commonly as the product of the RMS
60
voltage and current measurement. The power factor as
reported could change when one or the other of these
methods is used.
The power factor is multiplied by 214 before it is reported; thus, unity power factor is given by 16,384 decimal
(0x4000).
Line Frequency
The line frequency is derived directly from the mean NS
values over the three phases. It is reported as millihertz;
thus, a 50Hz line frequency is reported as decimal
50,000 (0xC350).
Phasor Angles
The phasor angles are taken directly from the angular
measurement values determined at each DSP cycle.
The angle is reported in units of 0.01 degree; thus, a
120° phasor is reported as decimal 12,000 (0x2EE0).
Energy
Energy is read as the net energy directly scaled from
the appropriate registers. For example, the energy read
from the ENRP.A register (real energy, phase A) is
composed of the difference between the A.EAPOS (real
energy, positive direction, phase A) and A.EANEG (real
energy, negative direction, phase A) registers scaled
by the ENR_CC register.
Note that the energy registers (ENRP.A, ENRP.B,
ENRP.C, ENRP.T, ENRQ.A, ENRQ.B, ENRQ.C, ENRQ.T,
ENRS.A, ENRS.B, ENRS.C, ENRS.T) represent the energy, in every case, since the last overflow event. For this
reason, software must keep track of overflow and make
adjustments accordingly when using this register set.
To calculate the ENR_CC register value, begin with the
full-scale voltage and full-scale current, the frame time,
and the desired LSB value for energy. Then perform the
following calculation:
I × VFS × t FR
ENR _ CC = FS
2 16 × ENR _ LSB
Example: It is essential to ensure that the correct units
are maintained throughout the calculation. In this example, assume that the full-scale voltage is 558.1V, the
full-scale current is 102.4A, the frame time is the default
of 360μs, and the desired LSB is 100 milliwatt-hours
after the 32 bits are discarded; that is, the LSB is 0.1 x
2-32 watt-hours. Notice, however, that the frame time is
given in microseconds and must be converted to hours
before the calculation can be performed: 360μs is 100
x 10-9 hours. So the calculation proceeds as follows:
102.4 x 558.1 x 100 x 10-9/(216 x 0.1 x 2-32) = 3745 =
0x0EA1
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Meter Constant
A meter constant is the number of pulses that are generated during a standard measurement interval; for
example, a meter might specify a meter constant of
1600 pulses per kilowatt-hour. The THR1 and THR2
registers are used to specify the meter constant
according to the following formula:
The PLS1_WD and PLS2_WD registers contain the time
in ADC frame periods that the pulses remain in the
active state when triggered. By default, these registers
contain decimal 156 (0x9C) giving, at the default frame
rate, a pulse width of approximately 50ms.
Each pulse generator can select one parameter to be
accumulated over any combination of the three phases.
For example, one could select real energy accumulated
over all three phases for pulse output 1, and reactive
energy accumulated over all three phases for pulse
output 2. The particular parameters that can be accumulated are given in the register table.
Among the quantities that can be accumulated by the
pulse subsystem are the arithmetic active energy (that
is, the accumulated positive real energy minus the
accumulated negative real energy) and the absolute
active energy (that is, accumulated positive real energy plus accumulated negative real energy). Other
quantities include RMS voltage and current, positive
and negative real energy and reactive energy in each
of the four quadrants. Select the desired accumulation
value in the QNSEL field of the PLSCFG1 and
PLSCFG2 register.
Also in the pulse configuration registers you can select
which phases to include in the accumulation. Set any or
all the PHASEA, PHASEB, and PHASEC bits in the
PLSCFG1 or PLSCFG2 registers to include them in the
accumulation.
Generating Pulses
On every DSP cycle, the MAXQ3183 adds the value in
the selected register (or set of registers) to the pulse
accumulator. If the value in the pulse accumulator
exceeds the value in the associated threshold register
(THR1 or THR2), then a pulse is started and the value in
the threshold register is subtracted from the value in the
pulse accumulator.
THR =
2 16
K M × IFS × VFS × t FR
In this formula, THR is the value to be written to the
threshold register, KM is the desired meter constant (in
pulses per kilowatt hour), IFS and VFS are the full-scale
voltage and current, respectively, and tFR is the frame
period in units of hours, as in the previous calculation.
As an example, assume once again a full-scale voltage
value of 558.1V = 0.5581kV, a full-scale current value of
102.4A, a desired meter constant of 1600 pulses per
kilowatt hour, and a default frame time of 360μs (88.9 x
10-9 hours). The threshold register value can be calculated as:
65,536/(1600 x 102.4 x 0.5581 x 100 x 10-9) =
7,167,174 = 0x6D5CC6
Increasing the value of the threshold register reduces
the meter constant (that is, there are fewer pulses per
kilowatt-hour); reducing the threshold register increases
the meter constant (that is, there are more pulses per
kilowatt-hour.)
Interrupts
The MAXQ3183 contains an interrupt subsystem to
relieve the host processor of the burden of constantly
polling the device for status. Instead, under certain circumstances, the MAXQ3183 can activate an external
pin to alert the host processor that some condition
requiring host attention has occurred.
Interrupts are managed globally by the IRQ_MASK and
IRQ_FLAG registers. In general, when a bit becomes
set in the IRQ_FLAG register, an interrupt is generated
if the corresponding bit is set in the IRQ_MASK register.
Interrupts can be configured for the following conditions:
PWRF: This flag indicates the V DVDD to the
MAXQ3183 has fallen below its nominal operating
threshold (about 2.85V). This can be taken as an
indication that power failure is imminent and that the
host processor should begin taking steps to ensure
an orderly shutdown.
CHSCH: This flag indicates that the CHKSUM register changed its value.
______________________________________________________________________________________
61
MAXQ3183
Meter Pulse
The purpose of a meter pulse is generally to advance a
mechanical counter when such a device is used as a
display. Meter pulses are also used during calibration
since time intervals can be measured with great precision.
The MAXQ3183 supports two meter pulse outputs.
These outputs can be configured for either active positive or active negative pulses by means of the POPOL
bit in the OPMODE1 register. When triggered, the pulse
goes to its active state and remains there for a period of
time defined by the PLS1_WD or PLS2_WD register,
and then returns to the inactive state (unless triggered
again).
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
MAXQ3183
EOVF: Energy overflow. This flag indicates that one or
more energy accumulators (X.EAPOS, X.EANEG, etc.)
have overflowed. In a traditional meter, the host
processor would poll the MAXQ3183 to determine
which of the energy accumulators have overflowed and
adjust its internal accounting registers accordingly.
ISUMOVF: The vector sum of currents over the most
recent DSP cycle has exceeded the vector sum
threshold.
OC: The RMS current value on one or more of the
phases over the most recent DSP cycle has exceeded the value set in the OCLVL register.
OV: The RMS voltage on one or more of the phases
over the most recent DSP cycle has exceeded the
value set in the OVLVL register.
UV: The RMS voltage on one or more of the phases
over the most recent DSP cycle has failed to exceed
the value set in the UVLVL register.
NOZX: Zero crossings were not detected on one or
more of the phases during the DSP cycle.
DCHA: Tells the host processor that the direction of
net real energy flow on one of the three phases has
changed during the current DSP cycle as compared
to the previous DSP cycle.
DCHR: Tells the host processor that the direction of
net reactive energy flow on one of the three phases
has changed during the current DSP cycle as compared to the previous DSP cycle.
DSPRDY: Indicates that the latest DSP cycle has
just completed.
DSPOR: Indicates that the processing for the previous DSP cycle had not been completed before the
current DSP cycle became available for processing.
This overflow indication should never be seen in the
default configuration; however, under some conditions (faster ADC rate, slower CPU clock) the processing requirements may exceed the number of
CPU cycles available for DSP processing. Under
these circumstances, the clock rate may be
increased, the ADC rate may be reduced (that is,
the R_ADCRATE register may be increased), or the
functional load (such as fundamental mode calculations) may be cut.
Note that when DSPOR becomes set, all DSP calculations as well as all pulse outputs are invalidated.
The appropriate host response is to take the remedial action described above and discard the current
set of DSP result values.
62
Each phase has a local register that contains copies of
the OC, OV, UV, NOZX, DCHA, and DCHR bits. Thus,
to determine which phase(s) have exception conditions
requires four reads: the IRQ_FLAG register to determine which conditions are active that are causing the
interrupt to occur, and then a read to A.FLAGS,
B.FLAGS, and C.FLAGS to determine which of the
phases have the indicated condition.
Finally, each phase has a pair of local registers that
contain overflow flags for each energy accumulator. If
the EOVF bit is set in the IRQ_FLAG register, the host
should then read the A.EOVER, B.EOVER, and
C.EOVER registers to determine which of the phases
have overflow conditions. If fundamental mode operation is enabled, the host should read A.EFOVER,
B.EFOVER, and C.EFOVER as well. Each of these registers contains a bit for each of real and reactive energy
in both positive and negative direction as well as
apparent energy.
Overvoltage and Overcurrent Detection
The MAXQ3183 detects overvoltage and overcurrent
events and can issue interrupt request signals to the
master when these events occur. The overvoltage level
can be programmed into the OVLVL register, while the
overcurrent level is determined by the OCLVL register.
Both OVLVL and OCLVL registers represent the bits
23:8 of the VRMS or IRMS registers. Any time the
MAXQ3183 detects the RMS-value exceeding a threshold level, the OV or OC interrupt flag is set. If enabled,
any of these flags issues an interrupt request. All interrupt flags are “sticky” bits—the MAXQ3183 never
clears them on its own unless a reset occurs. The interrupt flags should be cleared by the master by writing
the appropriate register.
Meter Units to Real Units Conversion
All energy calculations, including various threshold
checks, are performed internally in fixed format in meter
units. Therefore, the threshold values must be supplied
by the user in meter units as well. This section summarizes how to convert real units (V, A, kWh, W, and kAh)
into meter units and vice versa.
The conversion factors are based on the settings of tFR,
VFS, and IFS, defined by the user’s design.
t FR is analog scan frame timing. This parameter is
defined by the R_ADCRATE setting and system clock
frequency fSYS:
tFR = (R_ADCRATE + 1) x 8/fSYS
Default conditions are R_ADCRATE = 359, fSYS = 8MHz.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
IFS is full-scale current. This is the input current that
produces full-scale ADC output; defined by the hardware current transducer ratio ITR and ADC full-scale
input voltage VFSADC:
IFS = VFSADC x ITR
Default conditions are VFSADC = 1.024V. ITR is design
dependent.
Meter units are defined with respect to the base parameters as shown in Table 5.
When reading virtual registers, the MAXQ3183 uses the
configurable conversion coefficients AMP_CC,
VOLT_CC, PWR_CC, and ENR_CC to return meaningful
data. Table 6 describes how to set the coefficients.
Table 5. Meter Unit Definitions
REGISTER OR ACCUMULATOR
METER UNIT (1 LSB)
Current RMS: X.IRMS
MU_AMP = IFS/224
Pulse output current RMS
THR1 or THR2, when pulse output configured to IRMS
Voltage RMS: X.VRMS
MU_VOLT = VFS/224
Pulse output RMS voltage
THR1, or THR2 when pulse output configured to VRMS
Energy: X.ACT, X.REA, X.APP, X.EAPOS, X.EANEG, X.ERPOS,
X.ERNEG, X.ES
Fundamental Energy: X.ACTF, X.REAF, X.APPF, X.EAFPOS,
X.EAFNEG, X.ERFPOS, X.ERFNEG, X.ESF
Pulse Output Energy: THR1 or THR2
MU_ENR = VFS x IFS x tFR/216
Power: PWRP.X, PWRQ.X, PWRS.X
MU_PWR = VFS x IFS/232
When X.ESF Contains Amp-Hours: X.ESF
MU_AH = IFS x tFR/216
OCLVL, NOLOAD, I1THR, I2THR
IFS/216
OVLVL, UVLVL
VFS/216
Table 6. Virtual Register Coefficients
OUTPUT RESOLUTION
(1 LSB), DEFINED BY USER
COEFFICIENT
Power:
PWRP.X, PWRQ.X, PWRS.X, PWRPF.X,
PWRQF.X, PWRSF.X
PWR_LSB
PWR_CC = MU_PWR/PWR_LSB
Voltage:
V.X
VOLT_LSB
VOLT_CC = MU_VOLT/VOLT_LSB
Current:
I.X
AMP_LSB
AMP_CC = MU_AMP/AMP_LSB
Energy:
ENRP.X, ENRQ.X, ENRS.X, ENRPF.X,
ENRQF.X, ENRSF.X
ENR_LSB
ENR_CC = MU_ENR/ENR_LSB
VIRTUAL REGISTER
______________________________________________________________________________________
63
MAXQ3183
VFS is full-scale voltage. This is the input voltage that
produces full-scale ADC output; defined by the hardware voltage transducer ratio VTR and ADC full-scale
input voltage VFSADC:
VFS = VFSADC x VTR
Default conditions are VFSADC = 1.024V. VTR is design
dependent.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
I0P
R1
544kΩ
R2
1kΩ
VA (AC)
R
10Ω
VOP
IA (AC)
MAXQ3183
VN
MAXQ3183
VCOMM
R
10Ω
I0N
Figure 13. Sample Voltage Input Circuit
Units Conversion Examples
The conversions from meter units to physical units are
illustrated with the simplified input circuits in Figures 13
and 14. The voltage input circuit is a voltage-divider.
Current input is through a current transfer with turn ratio
of 2000:1.
The voltage transducer ratio (VTR) = (R1 + R2)/R2 =
545, VFS = 558.1V.
The current transducer ratio (ITR) = CT_N/(2 x R) =
2000/(2 x 10) =100 (A/V), IFS = 102.4A.
The input circuits should be designed to avoid getting
too close to the ADC input full scale at the specified
maximum ratings. So for the above circuits, we would
specify the maximum input current = 70A (RMS) and
maximum voltage = 390V (RMS), to ensure that peak of
sinusoudal waveform never exceeds IFS or VFS.
Use the default ADC timing tFR = 360μs, we get the following meter unit to physical unit conversion coefficients (these coefficients are not part of the MAXQ3183
registers):
MU_AMP = IFS/224 = 6.1E-6 (A)
MU_VOLT = VFS/224 = 33.3E-6 (V)
MU_PWR = VFS x IFS/232 = 13.3E-6 (W)
MU_ENR = VFS x IFS x tFR/216 = 87.2E-9 (Wh)
For example, if we get 0x07654AF0 from reading
0x1CC register (phase A current RMS), the current
value it represents is
0x07654AF0 x MU_AMP = 47.33 (A)
For some low-end host microcontrollers, doing the
above math multiplication above could be difficult. For
this reason, the MAXQ3183 provides conversions for
some commonly needed parameters through the
VOLT_CC, AMP_CC, PWR_CC, and ENR_CC registers.
For example, if you want to display current in the resolution of 1mA, without having to use a multiplication
64
Figure 14. Sample Current Input Circuit
operation to convert from the meter unit value
0x07654AF0, you would set AMP_CC to 0x0190, and
read from virtual register 0x831 (phase A RMS current).
The output would be 0xB8E45170. Dropping the lower
2 bytes (right shifting 16 bits) gives 0xB8E4, or 47332
decimal (47332mA).
AMP_CC is computed as follows:
AMP_CC = (IFS/224)/AMP_LSB = MU_AMP/AMP_LSB
AMP_LSB = 0.001/216 (A)
IFS = 102.4A
AMP_CC = (102.4/224)/(0.001/216) = 400d = 0x0190
Calibration Procedure
Calibration Overview
Calibration ensures that the recorded voltage, current,
energy, and power are in accordance with the design
criteria. Before creating a calibration regimen, establish
the fundamental units of the meter: the full-scale voltage and current. Then adjust the gain registers using
calculated calibration constants to produce the expected reading in the raw current, voltage, energy, and
power factor registers.
The calibration constants should be stored in nonvolatile memory by the host microcontroller. Upon any
reset or loss of power, the host microcontroller must
reload the MAXQ3183 with the constants.
Calibration always follows a set of fundamental steps:
• Apply a known signal (voltage/current/power) to the
meter.
• Read the meter.
• Calculate the correction factor based on the difference between the applied signal level and the meter
reading.
• Write the correction factor to the appropriate register.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Note that these steps can occur more than once for a
given signal type to verify readings at different signal
levels.
There are two methods to read the meter in the above
second step. The first is to read the raw register associated with the value under calibration, for example,
A.VRMS for the phase A voltage channel; A.IRMS for
the phase A current channel, and A.ACT for phase A
real power.
The second calibration method assigns a pulse output
to the value being calibrated and measures the pulse
period. In practical use, the method chosen depends
on the specific application and the available equipment. For example, in some applications the voltage
and current are of no concern, but the energy accumulation must be very accurate. For these applications,
meter calibration sets with built-in pulse measurement
facilities can make the most sense.
The calibration procedure involves the following general steps:
• Calibrate voltage for a given phase by applying a
known voltage and adjusting the voltage gain
(A.V_GAIN for phase A) until the RMS voltage
(A.VRMS for phase A) reads the applied voltage in
the designated units.
• Calibrate current by applying a known current and
adjusting the current gain (A.I_GAIN for phase A)
until the RMS current (A.IRMS for phase A) reads the
applied current in the designated units. If desired,
the current can be calibrated at two points (low
range and high range) for more accuracy.
• Once the current gain and voltage gain are calibrated, the power/energy should not require any additional adjustment for most situations. Although, a
separate power gain register is available for further
fine-tuning of the power/energy accuracy. One must
keep in mind that anytime voltage or current is recalibrated, the power or energy accuracy is naturally
affected. So the power gain should be recalibrated to
achieve the desired accumulative effect of voltage,
current, and power gains.
• Calibrate the phase offset by applying a power factor
load and adjusting the phase angle offset accordingly. If desired, the phase offset can be calibrated at
up to three points for more accuracy.
Once these elements are calibrated for each phase, all
other information (power factor, reactive power, apparent power, etc.) is also properly calibrated. The
descriptions in the following sections deal specifically
with phase A, but the same procedure is followed with
phases B and C.
Calibrating Voltage
Ensure that there is no previous value in the gain register, A.V_GAIN, by setting this register to 0x4000.
• Apply a known voltage with RMS value close to the
desired maximum operating voltage (and less than
VFS/√2).
• Read the A.VRMS register. Note the value.
• Convert the known value to meter units by dividing it
by MU_VOLT (= VFS/224).
• Divide the applied value (in meter unit) by the value
read from the MAXQ3183. The result should be a
value between 0 and 2. If the value falls outside of
this range, you have probably miscalculated VFS.
• Multiply the calculated value by 214. The result is the
gain value to be programmed into A.V_GAIN. Ensure
the most significant bit is 0.
When the gain value is programmed, wait for 2 to 3
seconds, reread the RMS value from A.VRMS. Check
that the measured value is correct by comparing
A.VRMS against the applied voltage in meter unit.
Voltage Calibration Example
Assumptions: VFS is 558.1V. The applied voltage is 240
VRMS.
• Convert the applied voltage to meter units. This calculation gives 240 x 2 24 /558.1 = 7,214,714 =
0x006E1679.
• Read the A.VRMS register. You read 0x0708029.
This is 7,372,841 decimal.
• Divide the applied voltage by the voltage read from
the meter. The result is 7,214,714/7,372,841 =
0.97855.
• Convert to integer by multiplying 2 14 : 16,384 x
0.97855 = 16,033 = 0x3EA1. Write this value to the
A.V_GAIN register.
Calibrating Current
Ensure that there is no previous value in the gain register, A.I_GAIN, by setting this register to 0x4000.
• Apply a known current with RMS value close to the
desired maximum operating current (and much lower
than IFS/√2).
• Read the A.IRMS register. Note the value.
• Convert the known value to meter units by dividing it
by MU_AMP (= IFS/224).
______________________________________________________________________________________
65
MAXQ3183
• Read the meter quantity again to verify the calibration.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
• Divide the applied value (in meter unit) by the value
read from the MAXQ3183. The result should be a
value between 0 and 2. If the value falls outside of
this range, you have probably miscalculated IFS.
• Multiply the calculated value by 214. The result is the
gain value to be programmed into A.I_GAIN. Ensure
the most significant bit is 0.
When the gain value is programmed, wait for approximately 2 to 3 seconds, then reread the RMS value from
A.IRMS. Check that the measured value is correct by
comparing A.IRMS against the applied current in meter
unit.
Current Calibration Example
Assume IFS is 102.4A and the meter has a base current
of 10A and a maximum current of 60A.
• The meter is calibrated at the base current of 10A.
• Convert the applied current to meter units. This calculation gives 10 x 2 24 /102.4 = 1,638,400 =
0x00190000.
• Read the A.IRMS register. You read 0x0017DC85.
This is 1,563,781 decimal.
• Divide the applied current by the current read from the
meter. The result is 1,638,400/1,563,781 = 1.0477.
• Multiply by 214 x 1.0477 = 17,166 = 0x430E. Write
this value to the A.I_GAIN register.
Calibrating Phase Offset
For this calibration step, it is necessary to have a power
factor meter, capable of measuring phase angle, connected in the same circuit as the MAXQ3183 meter.
Note that calibration can be performed at any precision
power factor setting. We use a pure resistive load (PF =
1.0) load to illustrate the procedure.
• Apply a resistive load to the meter; the current drawn
by the load should correspond to the base current of
your meter.
• Record the phase angle and direction (capacitive or
inductive) reported on the power factor meter.
• Read and record the real and reactive energy from
the X.ACT and X.REA registers. Divide the reactive
energy by the real energy. This is the tangent of the
power-phase angle.
• Read the X.REA register. If the high-order bit is set,
the power factor reported in the above step is capacitive. If the high-order bit is clear, the power factor
reported in the above step is inductive.
• Now determine the correction factor: treating capacitive values as negative and inductive values as positive, subtract the angle read from the MAXQ3183
66
from the angle read from the reference meter. The
result is the compensation angle.
• Multiply the compensation angle (in radians) by
65,536. This is the value to write into X.PA0.
If I1THR and I2THR are left at their default values
(0x0000), then the value in X.PA0 is applied to the full
measurement range. Alternatively, you could write the
same value into X.PA0, X.PA1, and X.PA2. Then the
same compensation is applied through the whole measurement range regardless of the I1THR and I2THR settings. If desired, calibrate for the phase angle at up to
three different current levels to compensate for nonlinearity in the current sensor. See the Advanced
Operation section for more information.
Phase Offset Calibration Example
Assume the meter is a 10/60 meter; that is, the base
current is 10A and the maximum rated current is 60A.
IFS is 102.4A and VFS is 558.1V. The test point is 10A
and 240V.
• Connect the MAXQ3183-based meter under test in
series with a lab grade reference meter. See the configuration below.
• Apply power to the meter and apply a load of 10A
resistive.
• Verify that the I1THR, I2THR, A.PA0, A.PA1, and
A.PA2 registers contain zero.
• Read the power factor on the reference meter. You
read 1.5° capacitive. This is not unusual. The load
might not be truly resistive or reactance in the test
configuration could be reflected in the measurement.
• Read the real energy from register A.ACT (0x1D0).
You read 0x2865D6 (2,646,510 meter units).
• Read the reactive energy from register A.REA
(0x1D4). You read 0xFFFFA5C0 (-23,104 meter
units).
• Divide the reactive by the active power: -23,104/
2,646,510 = -0.009.
LAB
METER
LOAD
V
LINE
NEUTRAL
Figure 15. Offset Testing Setup
______________________________________________________________________________________
UNIT
UNDER
TEST
V
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
• Subtract the UUT phase offset from the reference
meter phase offset. In this case, the phase needs to
move 1° toward the capacitive. Convert this value to
radians: 1° x π/180° = 0.0175 radians.
• Multiply this value by 65,536. The result is 572
(0x023C).
• Because the phase correction is toward the capacitive, the value must be complemented. The two’s
complement of 0x023C is 0xFDC4. This is the value
that should be written to the PA0 phase compensation register.
At this point, the meter is compensated for a single
phase offset. If the phase offset were perfectly flat over
all current levels, that would be sufficient (and for many
current sensors, particularly current shunts, one point is
usually good enough.)
Interfacing the MAXQ3183 to
External Hardware
The MAXQ3183 has all the internal circuitry that is
needed for a sophisticated electricity meter, but specific external hardware is required when configuring the
meter for a particular application. The most critical
decision that must be made is how the load will be connected to the power source, and how the meter will be
connected to measure power consumed in the load.
This section covers how to select hardware components for a MAXQ3183 electricity meter.
Connections to the Power Source
Generally, three-phase power as delivered from the utility consists of four wires: three voltage phases and a
neutral wire. In one typical three-phase delivery system,
measuring from neutral to any phase would read 120V,
while measuring from any phase to any other phase
would read 208V. Connecting a load so that load current is taken from phase lines and returned to neutral is
called a wye-connected load. Connecting a load so
that load current is provided by one phase and
returned on another phase is called a delta-connected
load. The MAXQ3183 can measure power consumed in
either a wye-connected or a delta-connected load.
If the load is connected in a wye fashion, the voltage is
measured from the neutral lead to each of the phases,
and the current measuring device is placed in series
with the load, most often in the hot lead. The sensor is
not placed in the neutral lead to prevent a customer
from defrauding the utility by returning the current to
ground rather than neutral. A current sensor placed in
the hot lead makes fraud even more difficult.
A delta-connected load can have current measured in
two possible ways. If it is primarily desirable to know
how much power is delivered to the load, one can place
the current sensor in the load circuit between two phases. But if it is more important to know how much current
is being drawn from each supply phase, each current
sensor is placed in the line circuit of each single phase.
Most utilities are only concerned with the total amount
of energy being consumed. If individually accounting
for the power delivered by each phase is not a requirement, it is not necessary to measure all three voltages.
Instead, knowing only two voltages and the three currents is all that is necessary to measure total energy
usage.
There are several ways of doing this. In a wye arrangement, one of the phases—usually phase B—–can be
considered the voltage reference point instead of neutral. Then the voltage measurements can be made from
phase A to phase B and from phase C to phase B. By
using some simple arithmetic, the power delivered by
phase A, phase B, and phase C can be calculated
even though only two voltages are available.
A second mechanism is to have a delta-connected
load, but with one leg—usually the BC leg—split into
two equal loads. The point where the load is split is
defined as the reference. In this arrangement, it is only
necessary to know the voltage between phase C and
the split and phase A and the split, since VC = -VA.
Finally, there is the connection arrangement in which
the load is in a delta configuration with the current sensor at each load, but it is still desired to determine how
much current is in each supply branch. The MAXQ3183
supports all of these connection arrangements.
Sensor Selection
The MAXQ3183 supports a variety of voltage and current sense elements. This section describes the properties of many of these sensing devices.
Voltage Sensors
Voltage-Divider
A voltage-divider is an ideal voltage-sensing element
when there is no need for voltage isolation. Modern
resistors have virtually no parasitic capacitance or
inductance at the frequencies of interest in an electricity meter and have extremely low variation with temperature. When selecting resistors for a voltage-divider,
keep the division ratio high enough so that the peak
voltage value cannot exceed the maximum allowable
input voltage. In the MAXQ3183, the peak input voltage
is about 1V; consequently, a divider in the range of
400:1 to 600:1 is ideal.
______________________________________________________________________________________
67
MAXQ3183
• Take the inverse tangent of this value. You get -0.5°;
that is, 0.5° capacitive.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
The second consideration is the total power dissipation
and voltage hold-off requirements of the resistor. It is
tempting to design a 400:1 divider with a 400kΩ resistor in series with a 1kΩ resistor, but that would force the
400kΩ resistor to dissipate about 140mW. This is not an
excessive amount of power, but if the design is to use
small SMT parts, it can handle greater than a 1/10W
SMT resistor. It is better to use a series of several smaller components to improve system reliability.
Voltage Transformer
If isolation is required between the meter electronics
and the line, a voltage transformer is required. A voltage transformer is designed to faithfully transfer an AC
voltage applied on the primary side to a sensor on the
secondary side. On the primary side, a voltage-divider
is used to reduce the voltage to a workable level. On
the secondary side, a load resistor is selected so that
the current in the transformer windings is safely within
the transformer’s linear operating region.
Because the impedance seen in the primary side of the
transformer is equal to the impedance of the load resistor in the secondary circuit plus impedance of the
transformer secondary winding at the operating frequency, it is easy to calculate the value of the required
voltage-divider resistors in the primary side. For example, assume we want a 500:1 divider ratio and assume
the load resistor is 600Ω and that the impedance of the
transformer secondary is 200Ω. The resistor required in
the primary is
(600 + 200) x 500 = 400kΩ
Often, this resistor is constructed from multiple
instances of a smaller value resistor; in this case, one
might use eight 50kΩ resistors. Doing so minimizes the
voltage requirements for the resistor chain and reduces
the possibility that a single point of failure will cause a
catastrophic failure.
Current Sensors
Current Shunt
A current shunt is a low-value (approximately 100μΩ to
a 100mΩ) resistor that converts a large-value current
into a small voltage. Shunts make good current sensors
because the output is an extremely linear representation of the measured current, current shunts can have
very low temperature coefficients, and they are inexpensive.
The power dissipated by a current shunt is inversely
proportional to its resistance and proportional to the
square of the output voltage. Consequently, there is
great incentive to reduce the resistance (and hence,
the output voltage) of a shunt. Often, full-scale current
68
in a shunt produces only a few millivolts of output, making a front-end amplifier essential. The MAXQ3183
includes a gain-of-32 amplifier in the current channels
that is automatically cycled in and out, depending on
the input voltage of the current channels.
Current shunts operate at line voltage, thus, the AFE
must be isolated from the line. That means that in a
wye-connected meter, the current sensing must be performed in the neutral return circuit (so that all voltages
into the current-sense amplifiers are referenced to neutral). It also means that the use of a shunt is precluded
for delta-connected meters; the MAXQ3183 cannot tolerate the line-voltage differential between channels.
Current Transformer
In a current transformer, the primary is usually one turn
of thick wire or buss bar and the secondary is often
1000 turns or more of magnet wire. A ferrite core magnetically couples the two. Thus, a large current in the
primary turn creates a small current but large voltage in
the secondary winding.
For example, assume a current transformer with a 1000
turn secondary. A 10A current in the primary winding
induces a 10mA current in the secondary. This current
is made to flow through a so-called “burden” resistor,
usually 10Ω to 20Ω. Assuming a 20Ω burden, our 10A
current thus produces a 200mV signal in the secondary.
Advanced Operation
Modifying the ADC Operation
There are several other registers that directly affect the
AFE function. These registers directly affect the hardware functionality, and should be modified only when it
is explicitly required. For example, if the MAXQ3183 is
operated at some frequency other than the nominal
8MHz system clock, modification of these registers by
supervisory code becomes necessary to maintain a
360μs frame time.
• R_ACFG: This register contains bits that disable the
ADC entirely, disable the voltage reference buffer
amplifier, and disable the ADC interrupt. Modifying
this register will likely disable or impair operation of
the MAXQ3183 internal firmware.
• R_ADCRATE: Modify this register to change the rate
at which the MAXQ3183 acquires samples. By
default, R_ADCRATE contains 359 decimal, which
means that the ADC acquires a sample every 360
system clocks. With an 8MHz clock, this translates to
45μs. If the system clock is slower, it may be advantageous to reduce this value to keep a 45μs per sample time constant.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Fine-Tuning the DSP Controls
Fine-Tuning the Line Frequency Measurement
Line frequency measurement is based on zero-crossing
detection. For that purpose each voltage signal is
passed through a digital lowpass filter, controlled by
the ZC_LPF register. This register specifies the b0 coefficient of a first-order LPF using following formula:
b0 =
ZC _ LPF
2 16
The MSB of this register must be zero.
For each phase A, B, and C, the MAXQ3183 counts the
number of scan frames (NS) between zero crossings
within a DSP cycle. Each individual phase A, B, or C
zero-crossing event contributes the raw NS count that
plugs as input to lowpass filter:
Yn = Yn - 1 + (AVG_NS/65,536) x (Xn - Yn - 1)
The filter coefficient is a signed 16-bit value and can be
configured by master. Here Y denotes the global NS
value, X denotes individual NS measurements produced by zero-crossing events detected on the phase
A, B, or C voltage channel. Note that if all three phase
voltages present, the filter above receives three inputs
each DSP cycle. The global NS value is used to generate the trigger for DSP processing. Note that the NS
value can be configured by the master, which could be
necessary if all three voltage signals are lost and no
zero-crossings are detected. The line period is then
calculated as a product of NS and the scan frame tFR.
The reciprocal of this value is the line frequency, which
can be obtained as a fixed-point value with 1 LSB =
0.001Hz by reading the LINEFR register.
Fundamental Mode Registers
The MAXQ3183 keeps another set of real and virtual
registers to track power and energy at the fundamental
line frequency. These “fundamental mode” registers
behave identically to the standard power and energy
registers, but are prefiltered to exclude harmonic
power.
The fundamental mode filter is specified in the B0FUND
and A1FUND registers. B0FUND is the feed-forward
coefficient and specifies the bandwidth of the fundamental mode filter; A1FUND is the feedback coefficient
and specifies the center frequency of the fundamental
mode filter.
In most cases, you can leave these filters at their
default values. If you wish to change the filter parameters, first choose the desired bandwidth:
b0 = π x bw x tFR
In this equation, bw is the desired bandwidth in hertz
and t FR is the frame period, typically 360μs. Set
B0FUND to b0 x 216. By default, B0FUND contains decimal 145 (0x91) giving a bandwidth of about 2Hz.
To set the center frequency, calculate a1 according to
the following formula:
a1 = 2 - 2(1 - b0) x cos(2π x fPK x tFR)
In this equation, b0 is the previously calculated feedforward coefficient, fPK is the desired center frequency
in hertz, and tFR is the ADC frame period. Set A1FUND
to a1 x 216. By default, A1FUND contains decimal 950
(0x3B6) giving a center frequency of approximately
50Hz.
The fundamental mode filter is, by default, quite sharp
with 3dB points only 1Hz off of the center frequency.
This means that if the frequency drifts even only slightly, the fundamental mode power measurement is likely
to have significant inaccuracy.
The MAXQ3183 provides a mechanism to track the frequency by updating the A1FUND register on each DSP
cycle. This mechanism is automatically enabled by
default.
You may wish to disable the automatic tracking facility
under some circumstances, particularly if you have
defined a broader bandwidth than default and are comfortable that the frequency will not drift beyond the
passband. To disable the filter, set the DFUNA bit in the
OPMODE2 register.
You may also elect to disable fundamental mode operation completely. To do this, set the DFUN bit in the
OPMODE2 register.
Harmonic Measurement
In addition to the ability to measure power and energy
at the fundamental frequency, the MAXQ3183 provides
a mechanism to isolate a particular harmonic on any
voltage or current channel and measure the amplitude
of that harmonic.
______________________________________________________________________________________
69
MAXQ3183
• R_ADCACQ: Modify this register to change the
acquisition time. The acquisition time is the time from
ADC power-on until conversion starts, and is provided to allow the input amplifiers to settle. By default
this is set to 47 decimal, or 6μs at an 8MHz system
clock. If the system clock rate is changed, then
R_ADCACQ should change so that this value
remains about 6μs.
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
To enable harmonic measurement, first select a voltage
or current channel to monitor. This is done in the
AUX_CFG register. The AUX_MUX field is the 4-bit
value that selects one of the three voltage channels or
one of the four current channels to monitor.
The order of the harmonic is set in ORDH field of the
AUX_CFG register.
Also in the AUX_CFG register are two bits that enable
the auxiliary channel and enable harmonic measurement on the auxiliary channel. To enable the auxiliary
channel, set the ENAUX bit. Once set, the MAXQ3183
will perform an RMS calculation on the selected channel. This is useful only for the IN (neutral current) channel, since every other voltage and current already have
RMS calculations applied by default. (The DADCNV bit
should be cleared in the SCAN_IN register in order to
enable sampling the IN channel.)
To enable harmonic measurement, set the ENHARM
bit. Now, the selected voltage or current signal is
passed to a filter that is identical to the second-order
fundamental filter, but that has separate parameters
(A1HARM, B0HARM).
Current Vector Sum
Current Total Harmonic Distortion Plus
Noise (THDN)
The MAXQ3183 supports two forms of current vector
sum calculations depending on whether neutral current
IN is available:
IVS3(t) = IA(t) + IB(t) + IC(t)
or
IVS4(t) = IA(t) + IB(t) + IC(t) + IN(t)
The sum must be calculated on instantaneous sample
basis. In a balanced 3-phase system, the vector sum IVS3
should be zero; a nonzero value indicates a current
unbalance. When neutral current available, vector sum
IVS4 should be always zero, no matter balanced or unbalanced loads; a nonzero value indicates tamper (energy
theft) or wrong meter connection. In the MAXQ3183, the
samples for IA, IB, IC, and IN are not simultaneous, therefore the device automatically applies an allpass filter to IB,
IC, and IN before calculating vector sum.
The MAXQ3183 calculates the RMS value of IVS3 or
IVS4 on-demand using the AUX channel. To activate
vector sum computations, the host must set following
configuration bits:
For IVS3:
1) AUX_CFG.ENAUX = 1—to enable the AUX channel
The MAXQ3183 can output the THDN ratio for selected
current channel on-demand. It is calculated as:
2) AUX_CFG.AUX_MUX = 1001b (0x9)—select IA + IB
+ IC input to the AUX channel
THDN.X =
X.IRMS 2
X.IRMS 2fund
The above settings result in AUX_CFG = 0x0049.
−1
This represents the ratio of the power of harmonics plus
noise over the power of the fundamental signal. To activate THDN computation, the host must first configure
the AUX channel to produce first harmonic (fundamental) on the desired current channel:
• Set AUX_CFG = 0x01C3 for current phase A
• Set AUX_CFG = 0x01C5 for current phase B
• Set AUX_CFG = 0x01C7 for current phase C
Then the THDN ratio can be read from one of the following virtual registers:
• Register 0x859 returns THDN.A for current phase A
• Register 0x85A returns THDN.B for current phase B
• Register 0x85C returns THDN.C for current phase C
Each register returns a raw binary value representing
the THDN ratio with LSB = 2–32. Since computation
involves signal filtering, the value THDN could require a
few seconds to settle before producing stable output.
70
For IVS4:
1) SCAN_IN.DADCNV = 0—to enable ADC sampling
neutral current IN (SCAN_IN = 0x60)
2) AUX_CFG.ENAUX = 1—to enable the AUX channel
3) AUX_CFG.AUX_MUX =1111b (0xF)—select IA + IB
+ IC + IN input to the AUX channel
The above settings result in AUX_CFG = 0x004F.
Once the above configuration is set, the MAXQ3183
starts accumulating the specified vector sum. The result
can then be read from the N.RMS register as raw value
or from I.N virtual register as converted value. If the
averaging filter is enabled (AVG_C > 0), the value could
require a few seconds to settle before producing stable
output. The MAXQ3183 has an additional control bit
AUX_CFG.INREV to reverse the sign of IN current. When
the bit is set (AUX_CFG = 0x006F), the MAXQ3183 calculates the value (IA + IB + IC - IN) instead of (IA + IB +
IC + IN). Doing so allows vector sum computation in
case of reverse connection of neutral current sensor.
A threshold (ISUMLVL, address 0x054) can also be
specified to cause the MAXQ3183 to generate an interrupt when the vector sum exceeds the threshold.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
• Current RMS
• Ampere-Hour
The ampere-hour value is readable from the X.ESF registers (X = A/B/C). Entry to LOWPM mode only occurs
at the request of the master. The master must set the
LOWPM_E bit (register address 0xC03) to 1 to place
the MAXQ3183 into LOWPM mode. Entering LOWPM
mode changes the clock frequency, thereby invalidating a number of configuration registers. As a result, the
master must immediately reload the configuration registers and filter with new, updated values before metering
measurement operations can continue.
The master instructs the MAXQ3183 to exit LOWPM
mode by reading the LOWPM_X bit (register address
0xC04).
Temperature
The MAXQ3183 contains a temperature sensor that can
be used by host software for any purpose, including
compensating power readings for temperature effects.
Use the virtual register command (TEMP_C, address
0xC01) to perform a temperature conversion. The
MAXQ3183 returns the value in degrees Celsius, with a
resolution of 1°C. Internally, the MAXQ3183 performs a
temperature sensor read and scales the sensor output
by the TEMP_CC (address 0x060) coefficient to provide
an output in degrees Celsius. The conversion formula is:
TEMP_C = RAW_TEMP x TEMP_CC/216 - 273.15
Where RAW_TEMP is raw digitized temperature sensor
output that is proportional to absolute temperature.
Conversion coefficient TEMP_CC must be calibrated
and set by the host; the default value is 0x0000.
Advanced Calibrations
Calibrating Current Offset
Ideal hardware should produce a current reading linearly proportional to the input current. However, due to
noise or other factors, the RMS current read by the
meter might not be precisely linear. The current offset
(X.OFFS_HI, X = A/B/C) can be used to compensate
the current channel nonlinearity.
Since the MAXQ3183 tracks the input current to determine what linearity compensation factors to use, the
user must choose two points (ilo and ihi) comfortably
above the low current threshold, and get the X.IRMS
current readings (rlo and rhi). Then calculate the Y-intercept of the line drawn between the two points, that is,
the offset. To calculate the value for the offset register,
use the following formula:
r i −i r
offs = hi lo hi lo
2 4 (i lo − i hi )
In this equation, ihi and rhi are the applied current and
the current reading, respectively, in meter units at the
higher of the two reference currents; ilo and rlo are the
applied current and the current reading, respectively, in
meter units at the lower of the two reference currents.
The gain (X.I_GAIN) may require recalibration after the
offset register updated.
Calibrating Linearity
The current channel includes a variable-gain amplifier
that introduces a gain of 32 when the current falls
below the low current threshold (about 1/32 of full-scale
current IFS). Because the gain of the amplifier cannot
be controlled with arbitrary precision, and because
high gain implies increased noise, it may be necessary
to calibrate the MAXQ3183 to maintain linearity at the
lowest inputs.
There are two settings that manage low-current linearity: an offset setting, OFFS_LO; and a gain setting,
GAIN_LO. Setting the offset is simple. Ensure no current is flowing in the current circuit. Read X.IRMS. To
calculate offset use following formula:
offs = -X.IRMS
Program the offs into the OFFS_LO register.
So, if the user reads 0x0113 from the X.IRMS register,
program 0xFEED into the X.OFFS_LO register. Setting
the X.GAIN_LO register means applying a current below
the low-current threshold, reading the value from the
MAXQ3183, and adjusting the gain accordingly. Note
that the low-end gain is applied in addition to the overall
gain provided in the X.I_GAIN register.
Apply a known current with peak value less than the
low-current threshold. Ensure that there is no previous
value in the low-current gain register, A.GAIN_LO, by
______________________________________________________________________________________
71
MAXQ3183
Low-Power Measurement Mode (LOWPM)
This mode enables a subset of metering functions while
operating from the lower frequency internal RC oscillator to conserve power. The actual system clock frequency used is the RC oscillator output frequency
divided by 8, which results in a system clock frequency
of approximately 1MHz.
The parameters provided in the LOWPM are:
• Voltage RMS
setting this register to 0x4000. Read the A.IRMS register (0x1CC). Note the value. Convert the known value to
meter units by multiplying the known value (in amperes)
by 224 and dividing by IFS. Divide the results of this calculation by the value read from the MAXQ3183. The
result should be a value between 0 and 2. Convert the
integer by multiplying 214, and ensure MSB is zero. The
result is the gain value to be programmed into
A.GAIN_LO.
• Convert the applied value to meter units by dividing it
by MU_PWR.
• Divide the applied value (in meter unit) by the value
read from the MAXQ3183. The result should be a
value between 0 and 2. If the value falls outside of
this range, IFS and/or VFS have probably been miscalculated.
• Multiply the calculated value by 214, and ensure the
MSB is zero. The result is the gain value to be programmed into A.E_GAIN.
• When the gain value is programmed, wait for 1 to 2
seconds, then reread the power value from PWRP.A.
Check that the measured value is correct by comparing PWRP.A against the applied power in meter unit.
Calibrating Power/Energy Gain
Once voltage and current have been calibrated, the
energy and power calculation automatically reflects the
calibrated voltage and current. However the energy
gain factor (X.E_GAIN, X = A/B/C) can be further tuned
to achieve even more accurate power and energy
result if necessary. For example, if the voltage and current calibration sources are not as accurate as the
power/energy calibration source, then the additional
gain calibration may be necessary. The following procedure for power/energy gain calibration is outlined for
phase A.
• Apply a precision unity power factor power (applied
value) that is close to the desired normal operating
point.
• Read the PWRP.A register. Note the value.
Multipoint Phase Offset Calibration
To perform the calibration at three current levels, note
the raw current value (X.IRMS) at each point. Label the
current values, from highest to lowest, I0, I1, and I2.
Program X.PA0, X.PA1, and X.PA2 with the phase offset
values calculated at I 0 , I 1 , and I 2 , respectively, as
described in the Calibrating Phase Offset section.
Finally, program I1THR with the average of I0 and I1,
and program I2THR with the geometric average of I1
and I2. Now as the current changes the phase offset is
adjusted accordingly. See Figure 16.
PA2
2
I2THR
PHASE OFFSET
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
PA0
1
I1THR
PA1
0
I2
I1
I0
INPUT CURRENT
Figure 16. Phase Offset vs. Input Current Calibration
72
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Analog Scan Configuration Registers
Time Slot Assignment—Current Channel X = A/B/C (SCAN_IX)
(A: 0x008, B: 0x00C, C: 0x00A)
Bit:
7
6
Name:
5
4
3
2
1
0
ADCMX
DADCNV
—
—
—
Reset A:
0x3
0
0
0
0
Reset B:
0x4
0
0
0
0
Reset C:
0x5
0
0
0
0
These registers configure the time slot normally assigned to current channels A/B/C. We recommend leaving these
registers at their default values. If they must be reassigned, one must ensure that all the current and voltage channels are reassigned properly so that the MAXQ3183 computes the power/energy parameters as intended by your
setup.
BIT
NAME
FUNCTION
7:4
ADCMX
Analog Conversion Select. This four-bit field determines which of the following analog inputs are
sampled during this time slot.
0000 = V0P - VN
0001 = V1P - VN
0010 = V2P - VN
0011 = I0P - I0N (Phase A Current: 0011)
0100 = I1P - I1N (Phase B Current: 0100)
0101 = I2P - I2N (Phase C Current: 0101)
0110 = INP - VN
1xxx = Temperature
All other values are reserved.
3
DADCNV
2:0
—
ADC Disable. When set, disables the ADC for this time slot.
Reserved.
______________________________________________________________________________________
73
MAXQ3183
Advanced Register Configurations
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Time Slot Assignment—Voltage Channel X = A/B/C (SCAN_VX)
(A: 0x009, B: 0x00D, C: 0x00B)
Bit:
7
Name:
6
5
4
3
2
1
ADCMX
DADCNV
PGG
Reset A:
0x0
0
0x0
Reset B:
0x1
0
0x0
Reset C:
0x2
0
0x0
0
These registers configure the time slot normally assigned to voltage channels A/B/C. The user may wish to change the
PGG settings to match the voltage sensor. However, it is recommended that the user not modify the ADCMX settings.
BIT
7:4
3
2:0
74
NAME
FUNCTION
ADCMX
Analog Conversion Select. This four-bit field determines which of the following analog inputs are
sampled during this time slot.
0000 = V0P - VN (Phase A Voltage: 0000)
0001 = V1P - VN (Phase B Voltage: 0001)
0010 = V2P - VN (Phase C Voltage: 0010)
0011 = I0P - I0N
0100 = I1P - I1N
0101 = I2P - I2N
0110 = INP - VN
1xxx = Temperature
DADCNV ADC Disable. When set, disables the ADC for this time slot.
PGG
Programmable Gain Amplifier Select. This three-bit field configures the programmable-gain amplifier at
the front-end of the analog input. The field has the following values:
000 = Gain of 1
001 = Gain of 2
010 = Gain of 4
011 = Gain of 8
100 = Gain of 16
101 = Gain of 32
All other values are reserved and can cause unpredictable behavior if selected.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
7
3
2
1
0
Name:
6
ADCMX
5
4
DADCNV
—
—
—
Reset:
0x6
1
0
0
0
This register configures the time slot normally assigned to the neutral current channel. The user can change the
DADCNV bit to enable/disable neutral current sampling. It is recommended to leave the other bits of this register at
their default values.
BIT
7:4
3
2:0
NAME
FUNCTION
ADCMX
Analog Conversion Select. This four-bit field determines which of the following analog inputs are sampled
during this time slot. All other values are reserved. By default, this register is set to 0110.
0000 = V0P - VN
0001 = V1P - VN
0010 = V2P - VN
0011 = I0P - I0N
0100 = I1P - I1N
0101 = I2P - I2N
0110 = INP - VN
1xxx = Temperature
DADCNV ADC Disable. When set, disables the ADC for this time slot.
—
Reserved.
______________________________________________________________________________________
75
MAXQ3183
Time Slot Assignment—Neutral Current Channel (SCAN_IN) (0x00E)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Time Slot Assignment—Temperature Channel (SCAN_TE) (0x00F)
Bit:
7
6
5
4
3
2
1
Name:
ADCMX
DADCNV
PGG
Reset:
0x8
1
0x2
0
This register configures the time slot normally assigned to the temperature measurement device. This register is
managed by the firmware and should not be modified by the host.
BIT
NAME
FUNCTION
7:4
ADCMX
Analog Conversion Select. This four-bit field determines which of the following analog inputs are
sampled during this time slot.
0000 = V0P - VN
0001 = V1P - VN
0010 = V2P - VN
0011 = I0P - I0N
0100 = I1P - I1N
0101 = I2P - I2N
0110 = INP - VN
0111 = Auto-zero ADC
1xxx = Temperature
By default, this register is set to 1000.
3
DADCNV
2:0
76
PGG
ADC Disable. When set, disables the ADC for this time slot.
Programmable Gain Amplifier Select. This three-bit field configures the programmable-gain amplifier at
the front end of the analog input. The field has the following values:
000 = Gain of 1
001 = Gain of 2
010 = Gain of 4
011 = Gain of 8
100 = Gain of 16
101 = Gain of 32
All other values are reserved and can cause unpredictable behavior if selected. This register is
managed by the firmware and should not be modified by the host.
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
Name:
—
—
—
12
11
Reset:
0
0
0
0
0
Bit:
7
6
5
4
Name:
ENHARM
ENAUX
INREV
—
Reset:
0
0
0
0
10
9
8
0
0
0
3
2
1
0
0
0
0
0
ORDH
AUX_MUX
The MAXQ3183 can monitor the RMS value of one auxiliary channel in addition to its normal processing. The
Auxiliary Channel Configuration register selects which input the auxiliary channel processes and what processing is
applied to the auxiliary channel.
BIT
NAME
15:13, 4
—
12:8
ORDH
Order of Harmonic (1–21). The output of harmonic voltage is read via virtual register 0x830 and current
at 0x840.
7
ENHARM
Enable Auxiliary Channel Harmonic Filter. When set, the auxiliary channel is processed through the
harmonic filter. The parameters for this filter can be set in the B0HARM and A1HARM registers.
6
ENAUX
Enable Auxiliary Channel. When set, enables auxiliary channel processing.
5
INREV
Sets the sign of the neutral current, used in the vector sum calculation.
0 = positive, i.e., IN is directly summed with IA + IB + IC.
1 = negative, -IN is summed with IA + IB + IC.
3:0
AUX_MUX
FUNCTION
Reserved.
Auxiliary Channel Input or Current Vector Sum Select. The lower three bits select the input to be
processed by the auxiliary channel if the MSB (bit 3) is cleared. When MSB is set, this field selects
vector sum computation:
1001 = IA + IB +IC
1111 = IA + IB + I C + IN (INREV = 0) or IA + IB + IC - IN (INREV = -1)
0001 = I N
0010 = VA
0011 = IA
0100 = VB
0101 = IB
0110 = VC
0111 = IC
All other values are reserved.
______________________________________________________________________________________
77
MAXQ3183
Neutral Current and Harmonics
Auxiliary Channel Configuration (AUX_CFG) (0x010)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
DSP System Configuration
System Clock Frequency (SYS_KHZ) (0x012)
Bit:
15
14
13
12
11
Name:
System Clock Frequency High Byte
Reset:
0x1F
Bit:
7
6
5
4
3
Name:
System Clock Frequency Low Byte
Reset:
0x40
10
9
8
2
1
0
This register contains the system clock frequency in kHz units. Because the default frequency is 8MHz, this register
defaults to 0x1F40.
Cycle Count (CYCNT) (0x01C)
Bit:
15
14
13
12
11
Name:
Cycle Count High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Cycle Count Low Byte
Reset:
0x10
10
9
8
2
1
0
This register contains the number of line cycles that will be accumulated in a single DSP cycle. When CYCNT line
cycles have been accumulated, the DSP performs power, power factor, and energy calculations. By default, the
cycle count is 0x10 (16 decimal).
78
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
31
30
29
28
27
Name:
Integer Portion, High Byte
Reset:
0x03
Bit:
23
22
21
20
19
Name:
Integer Portion, Low Byte
Reset:
0x28
Bit:
15
14
13
12
11
Name:
Fractional Portion, High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Fractional Portion, Low Byte
Reset:
0x00
26
25
24
18
17
16
10
9
8
2
1
0
The NS register defines the fundamental timing for the electricity meter. It defines a DSP cycle in terms the period of
the ADC scan frame. Generally, this register is calculated and updated automatically by the MAXQ3183 firmware
based on the zero-crossing detection, and whether noise rejection (REJ_NS) and averaging (AVG_NS) are enabled.
Host code can write to this register in order to set the desired DSP cycle duration. The duration of one scan frame
(tFR) is represented as 0x00010000.
Filter Coefficients
Line Cycle Noise Rejection Filter (REJ_NS) (0x02C)
Bit:
15
14
13
12
11
10
Name:
Line Cycle Noise Rejection Filter High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Line Cycle Noise Rejection Filter Low Byte
Reset:
0xC8
9
8
1
0
This register establishes the sensitivity of the NS rejection filter setting. NS is a measure of the line frequency. If a line
cycle occurs that is shorter or longer than the line cycle represented in the NS register, this filter determines whether
the cycle is used to update the NS value. For more information, see the NS register description. If this register is
zero, noise rejection is disabled for the line cycle counter.
______________________________________________________________________________________
79
MAXQ3183
Number of Scan Frames per DSP Cycle (NS) (0x040)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Line Cycle Averaging Filter (AVG_NS) (0x02E)
Bit:
15
14
13
12
11
Name:
Line Cycle Averaging Filter High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Line Cycle Averaging Filter Low Byte
Reset:
0x00
10
9
8
2
1
0
This register determines whether the NS value is averaged over previous values or whether the most recently measured
value is used directly. If the value of this register is nonzero, the NS value is averaged using the following formula:
x − y n−1
y n = y n−1 + AVG _ NS n
2 16
If the value of this register is zero, NS is not averaged. The MSB of this register must be zero.
Meter Measurement Averaging Filter (AVG_C) (0x030)
Bit:
15
14
13
12
11
10
Name:
Meter Measurement Averaging Filter High Byte
Reset:
0x40
Bit:
7
6
5
4
3
2
Name:
Meter Measurement Averaging Filter Low Byte
Reset:
0x00
9
8
1
0
This register determines whether the all other measured values in the electricity meter are averaged over time. If the
value of this register is nonzero, all measured meter values are averaged using the following formula:
x − y n−1
y n = y n−1 + AVG _ C n
2 16
If the value of this register is zero, no averaging is performed. The MSB of this register must be zero.
80
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
12
11
10
Name:
Meter Measurement Highpass Filter High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Meter Measurement Highpass Filter Low Byte
Reset:
0xC8
9
8
1
0
This register specifies the b0 coefficient of a first-order Butterworth filter using the following formula:
b0 =
HPF _ C
2 16
The MSB of this register must be zero.
Fundamental Filter Feed-Forward Coefficient (B0FUND) (0x034)
Bit:
15
14
13
12
11
10
Name:
Fundamental Filter Feed-Forward Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Fundamental Filter Feed-Forward Coefficient Low Byte
Reset:
0x91
9
8
1
0
This register specifies the b0 (feed-forward) coefficient for the fundamental-mode filter using the following formula:
b0 =
B0FUND
2 16
The MSB of this register must be zero.
______________________________________________________________________________________
81
MAXQ3183
Meter Measurement Highpass Filter (HPF_C) (0x032)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Fundamental Filter Feedback Coefficient (A1FUND) (0x036)
Bit:
31
30
29
28
27
26
Name:
Fundamental Filter Feedback Coefficient Byte 3
Reset:
0x00
Bit:
23
22
21
20
19
18
Name:
Fundamental Filter Feedback Coefficient Byte 2
Reset:
0x00
Bit:
15
14
13
12
11
10
Name:
Fundamental Filter Feedback Coefficient Byte 1
Reset:
0x03
Bit:
7
6
5
4
3
2
Name:
Fundamental Filter Feedback Coefficient Byte 0
Reset:
0xB6
25
24
17
16
9
8
1
0
This register specifies the a1 (feedback) coefficient for the fundamental-mode filter using the following formula:
a1 =
A1FUND
2 16
Harmonic Filter Feed-Forward Coefficient (B0HARM) (0x03A)
Bit:
15
14
13
12
11
10
Name:
Harmonic Filter Feed-Forward Coefficient High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Harmonic Filter Feed-Forward Coefficient Low Byte
Reset:
0x91
9
8
1
0
This register specifies the b0 (feed-forward) coefficient for the harmonic-mode filter using the following formula:
b0 =
B0HARM
2 16
The MSB of this register must be zero.
82
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
31
30
29
28
27
26
Name:
Harmonic Filter Feedback Coefficient Byte 3
Reset:
0x00
Bit:
23
22
21
20
19
18
Name:
Harmonic Filter Feedback Coefficient Byte 2
Reset:
0x00
Bit:
15
14
13
12
11
10
Name:
Harmonic Filter Feedback Coefficient Byte 1
Reset:
0x18
Bit:
7
6
5
4
3
2
Name:
Harmonic Filter Feedback Coefficient Byte 0
Reset:
0x31
25
24
17
16
9
8
1
0
This register specifies the a1 (feedback) coefficient for the harmonic mode filter using the following formula:
a1 =
A1HARM
2 16
Zero-Cross Lowpass Filter (ZC_LPF) (0x05A)
Bit:
15
14
13
12
11
Name:
Zero-Cross Lowpass Filter High Byte
Reset:
0x0B
Bit:
7
6
5
4
3
Name:
Zero-Cross Lowpass Filter Low Byte
Reset:
0x00
10
9
8
2
1
0
This register specifies the lowpass filter applied for zero-cross detection. The MSB of this register must be zero.
______________________________________________________________________________________
83
MAXQ3183
Harmonic Filter Feedback Coefficient (A1HARM) (0x03C)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Hardware Mirror Registers
ADC Configuration (R_ACFG) (0x04C)
Bit:
7
6
Name:
ADCASD
ADCRY
Reset:
0
0
5
4
3
2
1
0
ADCCD
ADCBY
ADCIE
ARBE
ADCE
0x0
0
1
1
1
This register is a mirror of a CPU register in the MAXQ3183. This register should not be modified by supervisory
code.
BIT
NAME
FUNCTION
7
ADCASD
Disable ADC Automatic Shutdown. Normally, the ADC analog section is powered off following a
conversion to conserve power. If this bit is set, the ADC leaves the analog section powered on
following a conversion.
6
ADCRY
ADC Data Ready. When a conversion is complete, this bit is set to indicate that data is available. This
bit generates an interrupt if ADCIE is set.
5:4
ADCCD
ADC Clock Divider. Sets the division ratio between the CPU master and ADC clock.
00 = divide by 1
01 = divide by 2
10 = divide by 4
11 = reserved
3
ADCBY
ADC Busy. When set, a single ADC conversion cycle is in progress. The bit is cleared on the
conclusion of the conversion cycle.
2
ADCIE
ADC Interrupt Enable. If set, the ADC interrupts the CPU at the completion of a conversion cycle.
1
ARBE
Reference Buffer Enable. If set, the reference buffer is enabled to drive the REFO pin.
0
ADCE
ADC Enable. If set, the ADC hardware is activated.
ADC Conversion Rate (R_ADCRATE) (0x04E)
Bit:
15
14
13
Reset:
—
—
—
Bit:
7
6
5
Name:
12
11
10
9
8
ADC Conversion Rate High Byte
—
—
—
—
1
4
3
2
1
0
Name:
ADC Conversion Rate Low Byte
Reset:
0x67
This register specifies the number of system clock cycles between consecutive ADC conversions. It defaults to
0x167 (359 decimal), which specifies 360 CPU clock cycles between conversions. This register is a mirror of a CPU
register in the MAXQ3183.
84
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
15
14
13
Name:
12
11
10
9
8
ADC Settling Time High Byte
Reset:
—
—
—
Bit:
7
6
5
Name:
—
—
—
—
—
4
3
2
1
0
ADC Settling Time Low Byte
Reset:
—
0x2F
This register is a mirror of a CPU register in the MAXQ3183. This register should not be modified by supervisory
code. This register specifies the time, in CPU clocks, that the ADC must wait after switching analog mux inputs
before beginning its conversion. This register defaults to 0x2F (47 decimal), which specifies a 48 CPU clock-cycle
delay from analog mux switching to the start of conversion.
SPI Configuration (R_SPICF) (0x052)
Bit:
7
6
5
4
3
2
1
0
Name:
ESPII
SAS
—
—
—
CHR
CKPHA
CKPOL
Reset:
1
0
0
0
0
0
0
0
This register is a mirror of a CPU register in the MAXQ3183. This register configures the SPI port of the MAXQ3183.
BIT
NAME
7
ESPII
Enable SPI Interrupt. If set, arrival of a character on the SPI bus causes a CPU interrupt.
FUNCTION
6
SAS
SPI Slave Select Polarity. If clear, SSEL is assumed to be active low; if set, SSEL is assumed to be
active high.
5:3
—
2
CHR
SPI Character Length. If clear, characters on the SPI bus are assumed to be 8 bits; if set, characters on
the SPI bus are assumed to be 16 bits.
1
CKPHA
SPI Clock Phase. If clear, data is sampled on the leading edge of the clock (low-to-high if the clock is
active high, and high-to-low if the clock is active low). If set, data is sampled on the trailing edge of the
clock (high-to-low if the clock is active high, and low-to-high if the clock is active low).
0
CKPOL
SPI Clock Polarity. If clear, the clock is assumed to be active high; if set, the clock is assumed to be
active low.
Reserved.
______________________________________________________________________________________
85
MAXQ3183
ADC Settling Time (R_ADCACQ) (0x050)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Timeouts
Communications Timeout (COM_TIMO) (0x056)
Bit:
15
14
13
12
11
Name:
Communications Timeout High Byte
Reset:
0x03
Bit:
7
6
5
4
3
Name:
Communications Timeout Low Byte
Reset:
0xE8
10
9
8
2
1
0
This register specifies the duration of SPI timeout in ADC frames (default 360μs).
Energy Accumulation Timeout (ACC_TIMO) (0x058)
Bit:
15
14
13
12
11
Name:
Energy Accumulation Timeout High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Energy Accumulation Timeout Low Byte
Reset:
0x05
10
9
8
2
1
0
This register specifies the time in DSP cycles that the MAXQ3183 waits before accumulating energy. If this register is
nonzero, it is decremented on each DSP cycle. If the result of the decrement is nonzero, the results of the DSP cycle
are discarded and are not accumulated to the energy registers. This register is useful for delaying the initiation of
energy accumulation on startup or after some hardware function has been modified.
86
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
15
14
13
12
11
10
Name:
Phase Accumulator Current Threshold 1 High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Phase Accumulator Current Threshold 1 Low Byte
Reset:
0x00
9
8
1
0
This register specifies the fraction of full-scale current that causes the MAXQ3183 to switch from PA0 to PA1 to provide phase-angle compensation. For more information, see the PA0, PA1, and PA2 register descriptions. The fullscale current is represented by 0x10000.
Phase Offset Current Threshold 2 (I2THR) (0x05E)
Bit:
15
14
13
12
11
10
Name:
Phase Accumulator Current Threshold 2 High Byte
Reset:
0x00
Bit:
7
6
5
4
3
2
Name:
Phase Accumulator Current Threshold 2 Low Byte
Reset:
0x00
9
8
1
0
This register specifies the fraction of full-scale current that causes the MAXQ3183 to switch from PA1 to PA2 to provide phase-angle compensation. For more information, see the PA0, PA1, and PA2 register descriptions. The fullscale current is represented by 0x10000.
Miscellaneous Gain
Neutral Current Gain (N.I_GAIN) (0x12E)
Bit:
15
14
13
12
11
Name:
Compensation Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Compensation Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains gain compensation coefficient for the neutral current channel measurement. The raw values
are taken from the selected measurement quantity and scaled by N.I_GAIN/214.
______________________________________________________________________________________
87
MAXQ3183
Phase-Angle Compensation
Phase Offset Current Threshold 1 (I1THR) (0x05C)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Gain, Fundamental Energy, Phase X = A/B/C (X.EF_GAIN) (A: 0x136, B: 0x222, C: 0x30E)
Bit:
15
14
13
12
11
Name:
Gain Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Gain Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains gain coefficient for phase X fundamental energy. The raw values are taken from the selected
measurement quantity and scaled by the following factor:
X.EF _ GAIN
2 14
Linearity Compensation
Linearity Offset, High Range, Phase X = A/B/C (X.OFFS_HI) (A: 0x138, B: 0x224, C: 0x310)
Bit:
15
14
13
12
11
Name:
Linearity Offset High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Linearity Offset Low Byte
Reset:
0x00
10
9
8
2
1
0
This signed register contains the linearity offset for phase X current channel when the programmable gain amplifier
is set to unity gain (that is, the measured current is above the low current threshold). The signed value represented
by this register is added to the current value according to following formula:
X.IRMS + X.OFFS_HI x 24
Linearity Gain Coefficient, Low Range, Phase X = A/B/C (X.GAIN_LO)
(A: 0x13A, B: 0x226, C: 0x312)
Bit:
15
14
13
12
11
Name:
Linearity Coefficient High Byte
Reset:
0x40
Bit:
7
6
5
4
3
Name:
Linearity Coefficient Low Byte
Reset:
0x00
10
9
8
2
1
0
This register contains the linearity coefficient for phase X current channel when the programmable gain amplifier is
set to gain of 32 (that is, the measured current is below the low current threshold). The effective gain is given by the
equation:
X.GAIN _ LO
2 14
88
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
15
14
13
12
11
Name:
Linearity Offset High Byte
Reset:
0x00
Bit:
7
6
5
4
3
Name:
Linearity Offset Low Byte
Reset:
0x00
10
9
8
2
1
0
This signed register contains the linearity offset for phase X current channel when the programmable gain amplifier
is set to gain of 32 (that is, the measured current is below the low current threshold). The signed value represented
by this register is added to the current value. The total linearity compensation is applied as follows:
X.GAIN_LO/214 x (X.IRMS + X.OFFS_LO)
Measurements—RAM Registers
On-Demand RMS Result (N.IRMS) (0x11C)
Bit:
31
30
29
Name:
28
27
26
25
24
18
17
16
10
9
8
2
1
0
RMS Result, Byte 3
Reset:
Bit:
23
22
21
Name:
20
19
RMS Result, Byte 2
Reset:
Bit:
15
14
13
Name:
12
11
RMS Result, Byte 1
Reset:
Bit:
Name:
7
6
5
4
3
RMS Result, Byte 0
Reset:
This register contains the result of the RMS calculation on the AUX channel. Usually, this is the neutral current channel, but can be defined to be the RMS average of any harmonic of the quantities defined in the AUX_MUX field of the
AUX_CFG register.
______________________________________________________________________________________
89
MAXQ3183
Linearity Offset, Low Range, Phase X = A/B/C (X.OFFS_LO) (A: 0x13C, B: 0x228, C: 0x314)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Fundamental Energy
Fundamental Energy Overflow Flags, Phase X = A/B/C (X.EFOVER)
(A: 0x147, B: 0x233, C: 0x31F)
Bit:
7
6
5
4
3
2
1
0
Name:
—
—
—
SFOV
RNFOV
RPFOV
ANFOV
APFOV
Reset:
0
0
0
0
0
0
0
0
These bits indicate an overflow condition has occurred on a fundamental frequency energy accumulator. An overflow condition is not an error condition. Rather, it simply indicates that the value in the energy accumulator could be
smaller than the previous reading due to the overflow in the counter. To obtain the actual energy usage since the
previous reading, 0x100000000 must be added to the difference. These bits, once set, can be cleared only by the
host.
BIT
NAME
7:5
—
FUNCTION
Reserved.
4
SFOV
3
RNFOV
When set, indicates an overflow condition on the apparent fundamental-mode energy accumulator.
When set, indicates an overflow condition on the reactive negative fundamental-mode energy accumulator.
2
RPFOV
When set, indicates an overflow condition on the reactive positive fundamental-mode energy accumulator.
1
ANFOV
When set, indicates an overflow condition on the real negative fundamental-mode energy accumulator.
0
APFOV
When set, indicates an overflow condition on the real positive fundamental-mode energy accumulator.
Energy, Fundamental, Real Positive, Phase X = A/B/C (X.EAFPOS)
(A: 0x1FC, B: 0x2E8, C: 0x3D4)
Bit:
31
30
29
Name:
Bit:
22
21
Name:
14
13
Name:
25
24
20
19
18
17
16
12
11
10
9
8
2
1
0
Real Energy Byte 1
7
Name:
26
Real Energy Byte 2
15
Bit:
27
Real Energy Byte 3
23
Bit:
28
6
5
4
3
Real Energy Byte 0
On every DSP cycle, the contents of the X.ACTF register are tested, and if positive, are added to this register. When
this register overflows, the APFOV bit in the X.EFOVER register is set.
90
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
31
30
29
Name:
Bit:
23
22
21
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Real Energy Byte 2
15
14
13
Name:
Bit:
27
Real Energy Byte 3
Name:
Bit:
28
12
11
Real Energy Byte 1
7
6
5
Name:
4
3
Real Energy Byte 0
On every DSP cycle, the contents of the X.ACTF register are tested, and, if negative, absolute values are added to
this register. When this register overflows, the ANFOV bit in the X.EFOVER register is set.
Energy, Fundamental, Reactive Positive, Phase X = A/B/C (X.ERFPOS)
(A: 0x204, B: 0x2F0, C: 0x3DC)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
27
Reactive Energy Byte 3
Name:
Bit:
28
12
11
Reactive Energy Byte 1
7
6
5
4
3
Reactive Energy Byte 0
On every DSP cycle, the contents of the X.REAF register are tested, and, if positive, are added to this register. When
this register overflows, the RPFOV bit in the X.EFOVER register is set.
______________________________________________________________________________________
91
MAXQ3183
Energy, Fundamental, Real Negative, Phase X = A/B/C (X.EAFNEG)
(A: 0x200, B: 0x2EC, C: 0x3D8)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Energy, Fundamental, Reactive Negative, Phase X = A/B/C (X.ERFNEG)
(A: 0x208, B: 0x2F4, C: 0x3E0)
Bit:
31
30
29
Name:
Bit:
22
21
Name:
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
27
Reactive Energy Byte 3
23
Bit:
28
12
11
Reactive Energy Byte 1
7
6
5
Name:
4
3
Reactive Energy Byte 0
On every DSP cycle, the contents of the X.REAF register are tested, and, if negative, absolute values are added to
this register. When this register overflows, the RNFOV bit in the X.EFOVER register is set.
Energy Fundamental, Apparent, Phase X = A/B/C (X.ESF)
(A: 0x20C, B: 0x2F8, C: 0x3E4)
Bit:
31
30
29
Name:
Bit:
22
21
Name:
14
13
Name:
25
24
20
19
18
17
16
12
11
10
9
8
2
1
0
Apparent Energy Byte 1
7
Name:
26
Apparent Energy Byte 2
15
Bit:
27
Apparent Energy Byte 3
23
Bit:
28
6
5
4
3
Apparent Energy Byte 0
On every DSP cycle, the contents of the X.ESF register are added to this register. When this register overflows, the
SFOV bit in the X.EFOVER register is set. When the MAXQ3183 is operating in low-power mode, energy is not accumulated. However, during low-power mode, current values are accumulated to this register, making this register
accumulate ampere-hours.
92
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Bit:
31
30
29
Name:
Bit:
23
22
21
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Real Energy Byte 2
15
14
13
Name:
Bit:
27
Real Energy Byte 3
Name:
Bit:
28
12
11
Real Energy Byte 1
7
6
5
Name:
4
3
Real Energy Byte 0
This signed register provides the raw real energy accumulated over the most recent DSP cycle. For each ADC sample period, the real instantaneous power calculated from the instantaneous voltage and current is accumulated. At
the end of each DSP cycle, the result of the accumulation over the DSP cycle is copied to this register and is accumulated in X.EAPOS or X.EANEG, depending on the sign of the accumulated energy.
LSB of the energy registers is VFS x IFS x tFR/216.
Reactive Energy, Phase X = A/B/C (X.REA) (A: 0x1D4, B: 0x2C0, C: 0x3AC)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
Name:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
28
Reactive Energy Byte 3
12
11
Reactive Energy Byte 1
7
6
5
4
3
Reactive Energy Byte 0
This signed register provides the raw reactive energy accumulated over the most recent DSP cycle. For each ADC
sample period, the reactive instantaneous power calculated from the instantaneous voltage and current is accumulated. At the end of each DSP cycle, the result of the accumulation over the DSP cycle is copied to this register and
is accumulated in X.ERPOS or X.ERNEG, depending on the sign of the accumulated energy.
______________________________________________________________________________________
93
MAXQ3183
Energy Accumulated in the Last DSP Cycle
Real Energy, Phase X = A/B/C (X.ACT) (A: 0x1D0, B: 0x2BC, C: 0x3A8)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Apparent Energy, Phase X = A/B/C (X.APP) (A: 0x1D8, B: 0x2C4, C: 0x3B0)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Apparent Energy Byte 2
15
14
13
Name:
Bit:
28
Apparent Energy Byte 3
12
11
Apparent Energy Byte 1
7
6
5
Name:
4
3
Apparent Energy Byte 0
This signed register provides the raw apparent energy accumulated over the most recent DSP cycle.
Fundamental Energy Accumulated in the Last DSP Cycle
Fundamental Real Energy, Phase X = A/B/C (X.ACTF) (A: 0x1DC, B: 0x2C8, C: 0x3B4)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
15
26
25
24
20
19
18
17
16
14
13
12
11
10
9
8
2
1
0
Real Energy Byte 1
7
Name:
27
Real Energy Byte 2
Name:
Bit:
28
Real Energy Byte 3
6
5
4
3
Real Energy Byte 0
This signed register accumulates energy in the same fashion as the X.ACT register, but only at the fundamental line
frequency.
94
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Reactive Energy Byte 2
15
14
13
Name:
Bit:
28
Reactive Energy Byte 3
12
11
Reactive Energy Byte 1
7
6
5
Name:
4
3
Reactive Energy Byte 0
This signed register accumulates energy in the same fashion as the X.REA register, but only at the fundamental line
frequency.
Fundamental Apparent Energy, Phase X = A/B/C (X.APPF) (A: 0x1E4, B: 0x2D0, C: 0x3BC)
Bit:
31
30
29
Name:
Bit:
23
22
21
Name:
Bit:
Name:
27
26
25
24
20
19
18
17
16
10
9
8
2
1
0
Apparent Energy Byte 2
15
14
13
Name:
Bit:
28
Apparent Energy Byte 3
12
11
Apparent Energy Byte 1
7
6
5
4
3
Apparent Energy Byte 0
This register accumulates energy in the same fashion as the X.APP register, but only at the fundamental line frequency.
______________________________________________________________________________________
95
MAXQ3183
Fundamental Reactive Energy, Phase X = A/B/C (X.REAF) (A: 0x1E0, B: 0x2CC, C: 0x3B8)
Bit:
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Checksum (CHKSUM) (0x066)
Bit:
15
14
13
Name:
12
11
10
9
8
2
1
0
Checksum High Byte
Reset:
Bit:
7
6
5
Name:
4
3
Checksum Low Byte
Reset:
This register contains the calculated 16-bit arithmetic checksum over critical configuration and calibration registers.
It is updated on every DSP cycle. In use, the administrative processor records the value in the CHKSUM register and
then checks it periodically to verify that no configuration or calibration registers have changed. The MAXQ3183 sets
the CHSCH bit when this register’s value changes.
The registers included in the checksum calculation include the following:
SYS_KHZ
96
THR2
R_ADCRATE
A.I_GAIN
B.I_GAIN
C.I_GAIN
VOLT_CC
REJ_NS
R_ADCACQ
A.V_GAIN
B.V_GAIN
C.V_GAIN
AMP_CC
AVG_NS
R_SPICF
A.E_GAIN
B.E_GAIN
C.E_GAIN
PWR_CC
AVG_C
ISUMLVL
A.EF_GAIN
B.EF_GAIN
C.EF_GAIN
ENR_CC
HPF_C
COM_TIMO
A.OFFS_HI
B.OFFS_HI
C.OFFS_HI
CYCNT
B0FUND
ACC_TIMO
A.GAIN_LO
B.GAIN_LO
C.GAIN_LO
PLSCFG1
OCLVL
I1THR
A.OFFS_LO
B.OFFS_LO
C.OFFS_LO
PLSCFG2
OVLVL
I2THR
A.PA0
B.PA0
C.PA0
PLS1_WD
UVLVL
ZC_LPF
A.PA1
B.PA1
C.PA1
THR1
NOLOAD
N.GAIN
A.PA2
B.PA2
C.PA2
PLS2_WD
R_ACFG
TEMP_CC
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Fundamental Real Power, Phase A/B/C/T (PWRPF.X)
(A: 0x881, B: 0x882, C: 0x884, T: 0x887)
This signed register contains the real instantaneous power delivered into phase A/B/C or total at the fundamental line
frequency only. Power is calculated from the instantaneous energy measurement according to the following equation:
PWRPF.X =
X.ACTF × PWR _ CC × 2 16
NS
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Fundamental Reactive Power, Phase A/B/C/T (PWRQF.X)
(A: 0x891, B: 0x892, C: 0x894, T: 0x897)
This signed register contains the reactive instantaneous power delivered into phase A/B/C or total at the fundamental
line frequency only. Power is calculated from the instantaneous energy measurement according to the following
equation:
PWRQF.X =
X.REAF × PWR _ CC × 2 16
NS
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
______________________________________________________________________________________
97
MAXQ3183
Measurements—Virtual Registers
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Fundamental Apparent Power, Phase A/B/C/T (PWRSF.X)
(A: 0x8A1, B: 0x8A2, C: 0x8A4, T: 0x8A7)
This register contains the instantaneous apparent power delivered into phase A/B/C or total at the fundamental line
frequency only. Power is calculated from the instantaneous energy measurement according to the following equation:
PWRSF.X =
X.APPF × PWR _ CC × 2 16
NS
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Fundamental Real Energy, Phase A/B/C/T (ENRPF.X)
(A: 0x8E1, B: 0x8E2, C: 0x8E4, T: 0x8E7)
This signed register contains the real accumulated energy delivered into phase A/B/C or total. The register is calculated according to the following formula:
ENRPF.X = ENR_CC x (X.EAFPOS - X.EAFNEG)
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Fundamental Reactive Energy, Phase A/B/C/T (ENRQF.X)
(A: 0x8F1, B: 0x8F2, C: 0x8F4, T: 0x8F7)
This signed register contains the reactive accumulated energy delivered into phase A/B/C or total. The register is
calculated according to the following formula:
ENRQF.X = ENR_CC x (X.ERFPOS - X.ERFNEG)
98
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
______________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
This register contains the apparent accumulated energy delivered into phase A/B/C or total. The register is the product of the ENR_CC and X.ESF registers.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0 (LSByte)
Current Total Harmonic Distortion Plus Noise, Phase A/B/C (THDN.X)
(A: 0x859, B:0x85A, C: 0x85C)
This signed register contains for a phase current the total harmonic distortion plus noise (power) ratio, computed as
below, where X.IRMSFUND is the fundamental current RMS.
THDN.X =
X.IRMS 2
2
X.IRMS FUND
−1
Note that the sign bit is at the most significant bit of byte 5.
Byte 7 (MSByte unused)
Byte 6 (unused)
Byte 5
Byte 4
Byte 3
Byte 2
Byte 1
Byte 0
______________________________________________________________________________________
99
MAXQ3183
Fundamental Apparent Energy, Phase A/B/C/T (ENRSF.X)
(A: 0x8B1, B: 0x8B2, C: 0x8B4, T: 0x8B7)
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Phasors
Phase B Phasor (VBPH: 0x852)
This register reports phase angle of voltage phase B
with respect to voltage phase A. The value is
expressed in units of 0.01 degree; thus, the nominal
value is 12000 decimal (0x2EE0). This value is calculated based on zero-crossing detection. It may exhibit
noticable error in the presence of harmonics on voltage
channels. This register is 2 bytes wide.
Phase C Phasor (VCPH: 0x854)
This register reports phase angle of voltage phase C
with respect to voltage phase A. The value is
expressed in units of 0.01 degree; thus, the nominal
value is 24000 decimal (0x5DC0). This value is calculated based on zero-crossing detection. It may exhibit
noticable error in the presence of harmonics on voltage
channels. This register is 2 bytes wide.
Harmonics
RMS Voltage, Harmonic (V.HARM) (0x830)
This register reports the RMS voltage. The units are
defined by the VOLT_CC setting. Use AUX_CFG to
configure the phase (A/B/C) and harmonic order
desired.
RMS Current, Harmonic/Neutral (I.N, I.HARM) (0x840)
This register reports the harmonic RMS current of
selected phase (A/B/C) and harmonic order, harmonic,
or the RMS current of the neutral current channel. The
units are defined by the AMP_CC setting. Use
AUX_CFG to configure the phase (A/B/C) and harmonic
order desired.
Ratio of Harmonic/Fundamental (HARM_NF) (0x850)
This register reports the ratio of the selected harmonic
RMS over the fundamental RMS of the same signal
(except IN). The master must configure the AUX_CFG
register to enable the AUX channel, enable harmonics,
and select AUX_MUX before reading this register. This
register is 4 bytes wide, LSB = 2-16.
Special Commands
Table 7 shows the read-only virtual registers that activate special commands when read by the master.
Some commands return dummy values.
Applications Information
Grounds and Bypassing
Careful PCB layout significantly minimizes noise on the
analog inputs, resulting in less noise on the digital I/O
that could cause improper operation. The use of multilayer boards is essential to allow the use of dedicated
power planes. The area under any digital components
should be a continuous ground plane if possible. Keep
any bypass capacitor leads short for best noise rejection and place the capacitors as close to the leads of
the devices as possible.
The MAXQ3183 must have separate ground areas for
the analog (AGND) and digital (DGND) portions, connected together at a single point.
Table 7. Virtual Registers That Activate Special Commands
DESCRIPTION
DATA
LENGTH
(BYTES)
NAME
ADDRESS
UPD_SFR
0x900
Reading this register copies the mirror registers (R_ADCF, R_ADCRATE,
R_ADCACQ, R_SPICF) into hardware SFR registers. The read returns dummy data.
1
UPD_MIR
0xA00
Reading this register copies hardware SFR registers into mirror registers (R_ADCF,
R_ADCRATE, R_ADCACQ, R_SPICF). The read returns dummy data.
1
DSPVER
0xC00
Reading this register returns the DSP firmware version number.
2
TEMP_C
0xC01
Reading this register initiates the on-chip temperature sensor conversion. Upon
completion, the temperature value is returned in degree Celsius, with a resolution of
1°C. The TEMP_CC register must be configured before reading this register.
2
ENTER STOP
0xC02
Reading this register places the device into Stop Mode.
1
ENTER LOWPM
0xC03
Reading this register places the device into LOWPM Mode.
1
EXIT LOWPM
0xC04
Reading this register exits LOWPM Mode.
1
100
_____________________________________________________________________________________
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
Additional Documentation
Designers must ensure they have the latest MAXQ3183
errata documents. Errata sheets contain deviations
from published specifications. A MAXQ3183 errata
sheet for any specific device revision is available at
www.maxim-ic.com/errata.
Technical Support
For technical support, go to https://support.maximic.com/micro.
Pin Configuration
TOP VIEW
VN
1
28
V2P
INP
2
27
V1P
I0P
3
26
V0P
I0N
4
25
AVDD
I1P
5
24
VREF
I1N
6
23
VCOMM
I2P
7
22
DVDD
I2N
8
21
RESET
AGND
9
20
CFQ
XTAL2
10
19
CFP
XTAL1
11
18
DGND
IRQ
12
17
DVDD
SSEL
13
16
MISO
SCLK
14
15
MOSI
Specific Design Considerations for
MAXQ3183-Based Systems
To reduce the possibility of coupling noise into the
microcontroller, the system should be designed with a
crystal or oscillator in a metal case that is grounded to
the digital plane. Doing so reduces the susceptibility of
the design to fast transient noise.
Because the MAXQ3183 is designed for use in systems
where high voltages are present, care must be taken to
route all signal paths, both analog and digital, as far
away as possible from the high-voltage components.
It is possible to construct more elaborate metering
designs using multiple MAXQ3183 devices. This can be
accomplished by using a single SPI bus to connect all
the MAXQ3183 devices together but using separate
slave select lines to individually select each MAXQ3183.
MAXQ3183
TSSOP
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the
package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to
the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
28 TSSOP
U28+3
21-0066
_____________________________________________________________________________________
101
MAXQ3183
CMOS design guidelines for any semiconductor require
that no pin be taken above DVDD or below DGND.
Violation of this guideline can result in a hard failure
(damage to the silicon inside the device) or a soft failure (unintentional modification of memory contents).
Voltage spikes above or below the device’s absolute
maximum ratings can potentially cause a devastating
IC latchup.
Microcontrollers commonly experience negative voltage spikes through either their power pins or generalpurpose I/O pins. Negative voltage spikes on power
pins are especially problematic as they directly couple
to the internal power buses. Devices such as keypads
can conduct electrostatic discharges directly into the
microcontroller and seriously damage the device.
System designers must protect components against
these transients that can corrupt system memory.
Typical Application Circuit
VOLTAGE SENSE
R1
VA
V0P
R2
R1
VB
V1P
R2
MAXQ3183
R1
VC
V2P
R2
VCOMM
CURRENT TRANSFORMER
VN
I0P
R3
R3
I0N
I1P
R3
R3
I1N
I2P
R3
LB
LC
MISO
LA
MOSI
I2N
SCLK
R3
SSEL
MAXQ3183
Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
N
MASTER
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
102 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.