MAXIM MAX5894

19-3546; Rev 0; 2/05
KIT
ATION
EVALU
E
L
B
A
IL
AVA
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Features
The MAX5893 programmable interpolating, modulating,
500Msps, dual digital-to-analog converter (DAC) offers
superior dynamic performance and is optimized for highperformance wideband, single-carrier transmit applications. The device integrates a selectable 2x/4x/8x
interpolating filter, a digital quadrature modulator, and
dual 12-bit high-speed DACs on a single integrated circuit. At 30MHz output frequency and 500Msps update
rate, the in-band SFDR is 84dBc while consuming 1.1W.
The device also delivers 72dB ACLR for single-carrier
WCDMA at a 61.44MHz output frequency.
The selectable interpolating filters allow lower input data
rates while taking advantage of the high DAC update
rates. These linear-phase interpolation filters ease
reconstruction filter requirements and enhance the
passband dynamic performance. Individual offset and
gain programmability allow the user to calibrate out local
oscillator (LO) feedthrough and sideband suppression
errors generated by analog quadrature modulators.
The MAX5893 features a fIM / 4 digital image-reject
modulator. This modulator generates a quadrature-modulated IF signal that can be presented to an analog I/Q
modulator to complete the upconversion process. A
second digital modulation mode allows the signal to be
frequency-translated with image pairs at fIM / 2 or fIM / 4.
The MAX5893 features a standard 1.8V CMOS, 3.3V tolerant data input bus for easy interface. A 3.3V SPI™ port
is provided for mode configuration. The programmable
modes include the selection of 2x/4x/8x interpolating filters, fIM / 2, fIM / 4 or no digital quadrature modulation
with image rejection, channel gain and offset adjustment,
and offset binary or two’s complement data interface.
Pin-compatible 14- and 16-bit devices are also available.
Refer to the MAX5894** data sheet for the 14-bit version
and the MAX5895 data sheet for the 16-bit version.
♦ 72dB ACLR at fOUT = 61.44MHz (Single-Carrier
WCDMA)
♦ Meets 3G UMTS, cdma2000®, GSM Spectral Masks
(fOUT = 122MHz)
♦ Noise Spectral Density = -151dBFS/Hz at
fOUT = 16MHz
♦ 90dBc SFDR at Low-IF Frequency (10MHz)
♦ 86dBc SFDR at High-IF Frequency (50MHz)
Applications
Base Stations: 3G UMTS, CDMA, and GSM
Broadband Wireless Transmitters
♦ Low Power: 511mW (fCLK = 100MHz)
♦ User Programmable
Selectable 2x, 4x, or 8x Interpolating Filters
<0.01dB Passband Ripple
>99dB Stopband Rejection
Selectable Real or Complex Modulator Operation
Selectable Modulator LO Frequency: OFF, fIM / 2,
or fIM / 4
Selectable Output Filter: Lowpass or Highpass
Channel Gain and Offset Adjustment
♦ EV Kit Available (Order the MAX5895EVKIT)
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
PKG
CODE
MAX5893EGK
-40°C to +85°C
68 QFN-EP*
(10mm x 10mm)
G6800-4
*EP = Exposed paddle.
Selector Guide
RESOLUTION
(BITS)
DAC UPDATE
RATE (Msps)
INPUT
LOGIC
MAX5893
12
500
CMOS
MAX5894**
14
500
PART
CMOS
MAX5895
16
500
**Future product—contact factory for availability.
Broadband Cable Infrastructure
Instrumentation and Automatic Test Equipment (ATE)
CMOS
Simplified Diagram
Analog Quadrature Modulation Architectures
DATA
PORT B
2x
INTERPOLATING
FILTERS
SPI is a trademark of Motorola, Inc.
cdma2000 is a registered trademark of Telecommunications
Industry Association.
MODULATOR
DATACLK
1x/2x/4x
INTERPOLATING
FILTERS
Pin Configuration appears at end of data sheet.
DATA SYNCH
AND DEMUX
DATA
PORT A
DAC
DAC
OUTI
OUTQ
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX5893
General Description
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
ABSOLUTE MAXIMUM RATINGS
DVDD1.8, AVDD1.8 to GND, DACREF ..................-0.3V to +2.16V
AVDD3.3, AVCLK, DVDD3.3 to GND, DACREF ........-0.3V to +3.9V
DATACLK, A0–A11, B0–B9,
SELIQ/B11, DATACLK/B10, CS, RESET, SCLK,
SDI and SDO to GND, DACREF......-0.3V to (DVDD3.3 + 0.3V)
CLKP, CLKN to GND, DACREF..............-0.3V to (AVCLK + 0.3V)
REFIO, FSADJ to GND, DACREF ........-0.3V to (AVDD3.3 + 0.3V)
OUTIP, OUTIN, OUTQP,
OUTQN to GND, DACREF..................-1V to (AVDD3.3 + 0.3V)
SDO, DATACLK, DATACLK/BIO Continuous Current ..........8mA
Continuous Power Dissipation (TA = +70°C)
68-Pin QFN (derate 41.7mW/°C above +70°C)
(Note 1) ...................................................................3333.3mW
Junction Temperature ......................................................+150°C
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Thermal Resistance θJC (Note 1)....................................0.8°C/W
Note 1: Thermal resistance based on a multilayer board with 4 x 4 via array in exposed paddle area.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, DATACLK input mode, dual-port
mode, 50Ω double-terminated outputs, external reference at 1.25V, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
12
Bits
Differential Nonlinearity
DNL
±0.5
LSB
Integral Nonlinearity
INL
±1
LSB
Offset Error
OS
-0.01
Offset Drift
Full-Scale Gain Error
+0.01
±0.03
±0.6
%FS
ppm/°C
GEFS
-4
IOUTFS
2
20
mA
-0.5
+1.1
V
Gain-Error Drift
Full-Scale Output Current
±0.003
+4
±110
Output Compliance
%FS
ppm/°C
Output Resistance
ROUT
1
MΩ
Output Capacitance
COUT
5
pF
DYNAMIC PERFORMANCE
Maximum Clock Frequency
fCLK
Minimum Clock Frequency
fCLK
500
Maximum DAC Update Rate
fDAC
fDAC = fCLK or fDAC = fCLK / 2
Minimum DAC Update Rate
fDAC
fDAC = fCLK or fDAC = fCLK / 2
Maximum Input Data Rate
fDATA
500
Noise Spectral Density
fDATACLK = 125MHz,
fOUT = 16MHz, fOFFSET
= 10MHz, 0dBFS
MHz
Msps
1
125
fDATACLK = 125MHz,
fOUT = 16MHz, fOFFSET
= 10MHz, -12dBFS
2
MHz
1
Msps
MWps
No interpolation
-151
2x interpolation
-147
4x interpolation
-148
4x interpolation
-145
_______________________________________________________________________________________
dBFS/
Hz
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, DATACLK input mode, dual-port
mode, 50Ω double-terminated outputs, external reference at 1.25V, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
fDATACLK = 125MHz,
interpolation off, 0dBFS
MIN
90
fOUT = 30MHz
83
fOUT = 50MHz
In-Band SFDR
(DC to fDATA / 2)
SFDR
fDATACLK = 125MHz,
2x interpolation, 0dBFS
fDATACLK = 125MHz,
4x interpolation, 0dBFS
fOUT = 10MHz
Two-Tone IMD
Four-Tone IMD
ACLR for WCDMA
(Note 3)
TTIMD
FTIMD
ACLR
UNITS
88
83
fOUT = 50MHz
84
fOUT = 10MHz
90
fOUT = 30MHz
84
dBc
86
No interpolation
-100
2x interpolation
-100
4x interpolation
-100
2x interpolation,
fIM / 4 complex
fDATA = 125MHz, fOUT1 modulation
= 79MHz, fOUT2 =
4x interpolation,
80MHz, -6.1dBFS
fIM / 4 complex
modulation
MAX
72
77
fOUT = 30MHz
fOUT = 50MHz
fDATACLK = 125MHz,
fOUT1 = 9MHz, fOUT2 =
10MHz, -6.1dBFS
TYP
fOUT = 10MHz
-73
-75
dBc
fDATACLK = 62.5MHz,
fOUT1 = 9MHz, fOUT2 =
10MHz, -6.1dBFS
8x interpolation
-99
fDATACLK = 62.5MHz,
fOUT1 = 69MHz, fOUT2
= 70MHz, -6.1dBFS
8x interpolation,
fIM / 4 complex
modulation
-67
8x, highpass
fDATACLK = 62.5MHz,
interpolation,
fOUT1 = 179MHz, fOUT2
fIM / 4 complex
= 180MHz, -6.1dBFS
modulation
-62
fDATACLK = 125MHz, fOUT spaced 1MHz
apart from 32MHz, -12dBFS, 2x
interpolation
-93
fDATACLK = 61.44MHz,
fOUT = baseband
4x interpolation
74
8x interpolation
73
fDATACLK =
122.88MHz, fOUT =
61.44MHz
2x interpolation,
fIM / 4 complex
modulation
73
fDATACLK =
122.88MHz, fOUT =
122.88MHz
4x interpolation,
fIM / 4 complex
modulation
69
dBc
dB
_______________________________________________________________________________________
3
MAX5893
ELECTRICAL CHARACTERISTICS (continued)
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
ELECTRICAL CHARACTERISTICS (continued)
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, DATACLK input mode, dual-port
mode, 50Ω double-terminated outputs, external reference at 1.25V, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
Output Propagation Delay
SYMBOL
tPD
CONDITIONS
MIN
TYP
MAX
UNITS
1x interpolation (Note 4)
2.9
ns
Output Rise Time
tRISE
10% to 90% (Note 5)
0.75
ns
Output Fall Time
tFALL
10% to 90% (Note 5)
1
ns
Output Settling Time
To 0.5% (Note 5)
11
ns
Output Bandwidth
-1dB bandwidth (Note 6)
240
MHz
Passband Width
Ripple <-0.01dB
Stopband Rejection
Data Latency
0.4 x
fDATA
0.604 x fDATA, 2x interpolation
100
0.604 x fDATA, 4x interpolation
100
0.604 x fDATA, 8x interpolation
100
1x interpolation
22
2x interpolation
70
4x interpolation
146
8x interpolation
311
dB
Clock
Cycles
DAC INTERCHANNEL MATCHING
Gain Match
Gain-Match Tempco
Phase Match
Phase-Match Tempco
∆Gain
∆Gain/°C
∆Phase
fOUT = DC - 80MHz, IOUTFS = 20mA
±0.1
dB
IOUTFS = 20mA
±0.02
ppm/°C
fOUT = 60MHz, IOUTFS = 20mA
±0.13
Deg
∆Phase/°C fOUT = 60MHz, IOUTFS = 20mA
±0.006
Deg/°C
DC Gain Match
IOUTFS = 20mA
Channel-to-Channel Crosstalk
fOUT = 50MHz, fDAC = 250MHz, 0dBFS
-0.2
±0.04
+0.2
-90
dB
dB
REFERENCE
Reference Input Range
0.125
Reference Output Voltage
VREFIO
Reference Input Resistance
RREFIO
Internal reference
1.14
Reference Voltage Drift
1.250
1.20
1.27
V
V
10
kΩ
±50
ppm/°C
CMOS LOGIC INPUT/OUTPUT (A11–A0, SELIQ/B11, DATACLK/B10, B9–B0, DATACLK)
0.7 x
DVDD1.8
Input High Voltage
VIH
Input Low Voltage
VIL
Input Current
IIN
±1
Input Capacitance
CIN
3
4
V
_______________________________________________________________________________________
0.3 x
DVDD1.8
V
±20
µA
pF
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, DATACLK input mode, dual-port
mode, 50Ω double-terminated outputs, external reference at 1.25V, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
Output High Voltage
VOH
200µA load
Output Low Voltage
VOL
200µA load
Output Leakage Current
Three-state
Rise/Fall Time
CLOAD = 10pF, 20% to 80%
MIN
TYP
MAX
0.8 x
DVDD3.3
UNITS
V
0.2 x
DVDD3.3
V
1
µA
1.6
ns
CLOCK INPUT (CLKP, CLKN)
Differential Input Voltage Swing
VDIFF
Sine-wave input
>1.5
Square-wave input
>0.5
Differential Input Slew Rate
Common-Mode Voltage
VCOM
AC-coupled
VP-P
>100
V/µs
AVCLK /
2
V
Input Resistance
RCLK
5
kΩ
Input Capacitance
CCLK
3
pF
Minimum Clock Duty Cycle
45
%
Maximum Clock Duty Cycle
55
%
6.2
ns
CLKP/CLKN, DATACLK TIMING (Figure 4) (Note 7)
CLK to DATACLK Delay
tD
Data Hold Time, DATACLK
Input/Output (Pin 14)
tDH
Data Setup Time, DATACLK
Input/Output (Pin 14)
tDS
Data Hold Time, DATACLK/B10
Input/Output (Pin 27)
tDH
Data Setup Time, DATACLK/B10
Input/Output (Pin 27)
tDS
DATACLK output mode, CLOAD = 10pF
Capturing rising edge
1.0
Capturing falling edge
2.1
Capturing rising edge
0.4
Capturing falling edge
-0.7
Capturing rising edge
1.0
Capturing falling edge
2.3
Capturing rising edge
0.2
Capturing falling edge
-0.4
ns
ns
ns
ns
SERIAL PORT INTERFACE TIMING (Figure 3) (Note 7)
SCLK Frequency
fSCLK
CS Setup Time
tSS
Input Hold Time
Input Setup Time
Data Valid Duration
10
MHz
2.5
ns
tSDH
0
ns
tSDS
4.5
tSDV
6.5
ns
16.5
ns
_______________________________________________________________________________________
5
MAX5893
ELECTRICAL CHARACTERISTICS (continued)
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
ELECTRICAL CHARACTERISTICS (continued)
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, DATACLK input mode, dual-port
mode, 50Ω double-terminated outputs, external reference at 1.25V, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLIES
Digital Supply Voltage
DVDD1.8
1.71
1.8
1.89
V
Digital I/O Supply Voltage
DVDD3.3
3.0
3.3
3.6
V
V
Clock Supply Voltage
Analog Supply Voltage
AVCLK
3.135
3.3
3.465
AVDD3.3
3.135
3.3
3.465
AVDD1.8
1.71
1.8
1.89
V
IAVDD3.3
fCLK = 100MHz, 2x interpolation, 0dBFS,
fOUT = 10MHz, DATACLK output mode
110
130
IAVDD1.8
fCLK = 100MHz, 2x interpolation, 0dBFS,
fOUT = 10MHz, DATACLK output mode
10
15
Digital Supply Current
IDVDD1.8
fCLK = 100MHz, 2x interpolation, 0dBFS,
fOUT = 10MHz, DATACLK output mode
54
65
mA
Digital I/O Supply Current
IDVDD3.3
fCLK = 100MHz, 2x interpolation, 0dBFS,
fOUT = 10MHz, DATACLK output mode
7
10
mA
Clock Supply Current
IAVCLK
fCLK = 100MHz, 2x interpolation, 0dBFS,
fOUT = 10MHz, DATACLK output mode
3
5
mA
Total Power Dissipation
PTOTAL
Analog Supply Current
511
AVDD3.3
All I/O are static high or
low, bit 2 to bit 4 of
address 00h are set high
Power-Down Current
PSRRA
(Note 8)
mW
450
AVDD1.8
1
DVDD1.8
10
DVDD3.3
100
AVCLK
AVDD3.3 Power-Supply Rejection
Ratio
mA
µA
1
0.05
%FS/V
Note 2: All specifications are 100% tested at TA ≥ +25°C. Specifications at TA < +25°C are guaranteed by design and characterization data.
Note 3: 3.84MHz bandwidth, single carrier.
Note 4: Excludes data latency.
Note 5: Measured single-ended into a 50Ω load.
Note 6: Excludes sin(x)/x rolloff.
Note 7: Guaranteed by design and characterization.
Note 8: Parameter defined as the change in midscale output caused by a ±5% variation in the nominal supply voltage.
6
_______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
70
60
SFDR (dBc)
-12dBFS
40
70
60
-0.1dBFS
60
50
40
0
0
10
20
SPURS MEASURED BETWEEN
62.5MHz AND 125MHz
10
0
30
40
50
0
10
20
0
30
50
40
62.5
72.5
82.5
92.5
102.5
112.5
OUTPUT FREQUENCY (MHz)
OUTPUT FREQUENCY (MHz)
IN-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 4x INTERPOLATION
OUT-OF-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 4x INTERPOLATION
IN-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 4x INTERPOLATION
-0.1dBFS
80
70
60
-12dBFS
40
80
70
-6dBFS
-12dBFS
50
40
30
0
10
20
SPURS MEASURED BETWEEN
62.5MHz AND 250MHz
10
40
50
-12dBFS
40
LOWER SIDEBAND MODULATION
SPURS MEASURED BETWEEN
62.5MHz AND 125MHz
10
0
30
-6dBFS
50
20
20
0
60
30
20
SPURS MEASURED BETWEEN
0MHz AND 62.5MHz
-0.1dBFS
90
SFDR (dBc)
60
SFDR (dBc)
80
100
MAX5893 toc06
90
MAX5893 toc04
-0.1dBFS
-6dBFS
100
0
0
10
20
30
50
40
75
85
95
105
115
125
OUTPUT FREQUENCY (MHz)
OUTPUT FREQUENCY (MHz)
IN-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 4x INTERPOLATION
TWO-TONE IMD vs. OUTPUT FREQUENCY
fDATA = 125MWps, 2x INTERPOLATION
TWO-TONE IMD vs. OUTPUT FREQUENCY
fDATA = 125Msps, 4x INTERPOLATION
50
-12dBFS
40
30
20
UPPER SIDEBAND MODULATION
SPURS MEASURED BETWEEN
125MHz AND 187.5MHz
10
0
125
135
145
155
80
-9dBFS
60
-6dBFS
40
0
165
OUTPUT FREQUENCY (MHz)
175
0
25
50
-6dBFS
-12dBFS
90
60
-9dBFS
30
1MHz CARRIER SPACING
COMPLEX MODULATION FOR
OUTPUT FREQUENCIES
GREATER THAN 50MHz
20
120
TWO-TONE IMD (-dBc)
60
-12dBFS
100
TWO-TONE IMD (-dBc)
70
120
MAX5893 toc08
-0.1dBFS
MAX5893 toc07
-6dBFS
1MHz CARRIER SPACING
COMPLEX MODULATION FOR
OUTPUT FREQUENCIES
GREATER THAN 50MHz
0
75
CENTER FREQUENCY (MHz)
100
MAX5893 toc09
OUTPUT FREQUENCY (MHz)
90
SFDR (dBc)
UPPER SIDEBAND MODULATION
SPURS MEASURED BETWEEN
62.5MHz AND 125MHz
10
OUTPUT FREQUENCY (MHz)
120
80
-12dBFS
40
20
20
SPURS MEASURED BETWEEN
0MHz AND 62.5MHz
-0.1dBFS
50
30
30
20
-6dBFS
80
MAX5893 toc05
SFDR (dBc)
80
SFDR (dBc)
-6dBFS
80
90
SFDR (dBc)
100
-12dBFS
90
IN-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 2x INTERPOLATION
MAX5893 toc02
-0.1dBFS
-6dBFS
100
MAX5893 toc01
120
0UT-OF-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 2x INTERPOLATION
MAX5893 toc03
IN-BAND SFDR vs. OUTPUT FREQUENCY
fDATA = 125MWps, 2x INTERPOLATION
0
30
60
90
120
150
CENTER FREQUENCY (MHz)
_______________________________________________________________________________________
7
MAX5893
Typical Operating Characteristics
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, output is transformer-coupled to
50Ω load, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, output is transformer-coupled to
50Ω load, TA = +25°C, unless otherwise noted.)
GAIN MISMATCH vs. TEMPERATURE
fDATA = 125Msps, 2x INTERPOLATION
DIFFERENTIAL NONLINEARITY
vs. DIGITAL INPUT CODE
0.75
0.50
0.050
INL (LSB)
0.5
DNL (LSB)
GAIN MISMATCH (dB)
0.075
1.00
MAX5893 toc12
fOUT = 22.7MHz
AOUT = -6dBFS
INTEGRAL NONLINEARITY
vs. DIGITAL INPUT CODE
MAX5893 toc11
1.0
MAX5893 toc10
0.100
0
0.25
0
-0.25
0.025
-0.5
-0.50
-0.75
-1.0
10
35
60
512
0
TEMPERATURE (°C)
SUPPLY CURRENTS vs. DAC UPDATE RATE
2x INTERPOLATION, fOUT = 5MHz
450
350
300
250
1.8V TOTAL
150
100
3.3V TOTAL
512
4096
450
400
1.8V TOTAL
350
300
250
200
150
150
200
fDAC (MHz)
250
300
1536
2560
3584
4096
1024
2048
3072
DIGITAL INPUT CODE
SUPPLY CURRENTS vs. DAC UPDATE RATE
8x INTERPOLATION, fOUT = 5MHz
500
450
400
1.8V TOTAL
350
300
250
200
150
3.3V TOTAL
50
0
100
0
100
3.3V TOTAL
50
0
8
3584
1024
2048
3072
DIGITAL INPUT CODE
100
50
2560
500
SUPPLY CURRENT (mA)
400
1536
SUPPLY CURRENTS vs. DAC UPDATE RATE
4x INTERPOLATION, fOUT = 5MHz
MAX5893 toc13
500
200
-1.00
85
MAX5893 toc14
-15
SUPPLY CURRENT (mA)
-40
MAX5893 toc15
0
SUPPLY CURRENT (mA)
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
0
100
200
300
400
500
100
200
fDAC (MHz)
_______________________________________________________________________________________
300
fDAC (MHz)
400
500
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
WCDMA ACLR vs. OUTPUT FREQUENCY
fDATA = 76.8MWps, 4x INTERPOLATION
WCDMA ACLR vs. OUTPUT FREQUENCY
fDATA = 122.88MWps, 4x INTERPOLATION
90
SINGLE-CARRIER
ALTERNATE CHANNEL
70
SINGLE-CARRIER
ADJACENT CHANNEL
60
40
0
40
80
80
fCENTER (MHz)
WCDMA ACLR SPECTRAL PLOT
fDATA = 61.44MWps, 8x INTERPOLATION
WCDMA ACLR SPECTRAL PLOT
fDATA = 122.88MWps, 4x INTERPOLATION
-30
-40
-90
-100
-110
-110
-120
-120
fCENTER = 61.44MHz
SPAN = 25.5MHz
ACLR2 = 70dB
-80
ACLR1 = 69dB
-70
ACLR1 = 69dB
-60
CARRIER = -14dBm
-50
ACLR2 = 71dB
OUTPUT POWER (dBm)
ACLR2 = 73dB
ACLR1 = 72dB
ACLR1 = 73dB
ACLR2 = 73dB
-60
CARRIER = -12dBm
-50
MAX5893 toc19
-20
MAX5893 toc18
-40
OUTPUT POWER (dBm)
40
fCENTER (MHz)
-30
-90
0
160
120
-20
-100
SINGLE-CARRIER
ADJACENT CHANNEL
50
40
-80
70
60
50
-70
SINGLE-CARRIER
ALTERNATE CHANNEL
80
ACLR (dB)
80
MAX5893 toc17
90
ACLR (dB)
100
MAX5893 toc16
100
fCENTER = 122.88MHz
SPAN = 25.5MHz
_______________________________________________________________________________________
9
MAX5893
Typical Operating Characteristics (continued)
(DVDD1.8 = AVDD1.8 = 1.8V, AVCLK = AVDD3.3 = DVDD3.3 = 3.3V, modulator off, 2x interpolation, output is transformer-coupled to
50Ω load, TA = +25°C, unless otherwise noted.)
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Pin Description
PIN
NAME
FUNCTION
1
CLKP
Noninverting Differential Clock Input
2
CLKN
Inverting Differential Clock Input
3, 4, 5, 22–25,
40–43
N.C.
6, 21, 30, 37
DVDD1.8
Digital Power Supply. Accepts a 1.71V to 1.89V supply range. Bypass each pin to ground with a
0.1µF capacitor as close to the pin as possible.
7–12, 15–20
A11–A0
A-Port Data Inputs.
Dual-port mode:
I-channel data input. Data is latched on the rising/falling edge (programmable) of the DATACLK.
Single-port mode:
I-channel and Q-channel data input, with SELIQ.
13, 44
DVDD3.3
CMOS I/O Power Supply. Accepts a 3.0V to 3.6V supply range. Bypass each pin to ground with a
0.1µF capacitor as close to the pin as possible.
14
DATACLK
Programmable Data Clock Input/Output. See the DATACLK Modes section for details.
SELIQ/B11
Select I/Q-Channel Input or B-Port MSB Input.
Single-port mode:
If SELIQ = LOW, data is latched into Q-channel on the rising/falling edge (programmable) of
the DATACLK.
If SELIQ = HIGH, data is latched into I-channel on the rising/falling edge (programmable) of the
DATACLK.
Dual-port mode:
Q-channel MSB input.
26
27
Internally Connected. Do not connect.
Alternate DATACLK Input/Output or B-Port Bit 10 Input.
Single-port mode:
See the DATACLK Modes section for details.
DATACLK/B10
Dual-port mode:
Q-channel bit 10 input.
If unused connect to GND.
B-Port Data Bits 9–0.
Dual-port mode:
Q-channel inputs. Data is latched on the rising/falling (programmable) edge of the DATACLK.
Single-port mode:
Connect to GND.
28, 29, 31–36,
38, 39
B9–B0
45
SDO
Serial-Port Data Output
46
SDI
Serial-Port Data Input
47
SCLK
48
CS
49
RESET
Reset Input. Set RESET low during power-up.
50
REFIO
Reference Input/Output. Bypass to ground with a 1µF capacitor as close to the pin as possible.
51
DACREF
Current-Set Resistor Return Path. For a 20mA full-scale output current, connect a 2kΩ resistor between
FSADJ and DACREF. Internally connected to GND. Do not use as an external ground connection.
52
FSADJ
Full-Scale Adjust Input. This input sets the full-scale output current of the DAC. For a 20mA fullscale output current, connect a 2kΩ resistor between FSADJ and DACREF.
10
Serial-Port Clock Input. Data on SDI is latched on the rising edge of SCLK.
Serial-Port Interface Select. Drive CS low to enable serial-port interface.
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
PIN
NAME
FUNCTION
53, 67
AVDD1.8
54, 56, 59, 61,
64, 66
GND
55, 60, 65
AVDD3.3
57
OUTQN
Inverting Differential DAC Current Output for Q-Channel
58
OUTQP
Noninverting Differential DAC Current Output for Q-Channel
62
OUTIN
Inverting Differential DAC Current Output for I-Channel
63
OUTIP
Noninverting Differential DAC Current Output for I-Channel
68
AVCLK
Clock Power Supply. Accepts a 3.135V to 3.465V supply range. Bypass to ground with a 0.1µF
capacitor as close to the pin as possible.
EP
GND
Low Analog Power Supply. Accepts a 1.71V to 1.89V supply range. Bypass each pin to GND with
a 0.1µF capacitor as close to the pin as possible.
Ground
Analog Power Supply. Accepts a 3.135V to 3.465V supply range. Bypass each pin to GND with a
0.1µF capacitor as close to the pin as possible.
Exposed Pad. Must be connected to GND through a low-impedance path.
Functional Diagram
MODULATOR
MUX
MUX
2x
INTERPOLATING
FILTER
2x
INTERPOLATING
FILTER
2x
INTERPOLATING
FILTER
∑
DIGITAL
OFFSET
ADJUST
∑
fDAC
DATA SYNCH
AND DEMUX
B0–B11
OUTIP
IDAC
OUTIN
A0–A11
DATACLK
DIGITAL
GAIN
ADJUST
I
Q
fIM / 2, fIM / 4
I
Q
DIGITAL
OFFSET
ADJUST
MUX
MUX
∑
2x
INTERPOLATING
FILTER
2x
INTERPOLATING
FILTER
2x
INTERPOLATING
FILTER
SELIQ
MAX5893
∑
DIGITAL
GAIN
ADJUST
OUTQP
QDAC
OUTQN
fDAC
/2
/2
/2
/2
CONTROL REGISTERS
fCLK
SERIAL INTERFACE
RESET
SDO
SDI
CS
CLOCK BUFFERS
AND DIVIDERS
REFERENCE
SCLK
DACREF
FSADJ
REFIO
CLKN
CLKP
______________________________________________________________________________________
11
MAX5893
Pin Description (continued)
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Detailed Description
The MAX5893 dual, 500Msps, high-speed, 12-bit, current-output DAC provides superior performance in
communication systems requiring low-distortion analog-signal reconstruction. The MAX5893 combines two
DAC cores with 8x/4x/2x/1x programmable digital interpolation filters, a digital quadrature modulator, an SPIcompatible serial interface for programming the device,
and an on-chip 1.20V reference. The full-scale output
current range is programmable from 2mA to 20mA to
optimize power dissipation and gain control.
Each channel contains three selectable interpolating filters making the MAX5893 capable of 1x, 2x, 4x, or 8x
interpolation, which allows for low-input and high-output data rates. When operating in 8x interpolation
mode, the interpolator increases the DAC conversion
rate by a factor of eight, providing an eight-fold
increase in separation between the reconstructed
waveform spectrum and its first image. The MAX5893
accepts either two’s complement or offset binary input
data format and can operate from either a single- or
dual-port input bus.
The MAX5893 includes modulation modes at fIM / 2 and
fIM / 4, where fIM is the data rate at the input of the modulator. If 2x interpolation is used, this data rate is 2x the
input data rate. If 4x or 8x interpolation is used, this data
rate is 4x the input data rate. Table 1 summarizes the
modulator operating data rates for dual-port mode.
The power-down modes can be used to turn off each
DAC’s output current or the entire digital section.
Programming both DACs into power-down simultaneously will automatically power down the digital interpolator filters. Note the SPI section is always active.
The analog and digital sections of the MAX5893 have
separate power-supply inputs (AV DD3.3 , AV DD1.8 ,
AVCLK, DVDD3.3, and DVDD1.8), which minimize noise
coupling from one supply to the other. AVDD1.8 and
DVDD1.8 operate from a typical 1.8V supply, and all
other supply inputs operate from a typical 3.3V supply.
Serial Interface
The SPI-compatible serial interface programs the
MAX5893 registers. The serial interface consists of the
CS, SDI, SCLK, and SDO. Data is shifted into SDI on
the rising edge of the SCLK when CS is low. When CS
is high, data presented at SDI is ignored and SDO is in
high-impedance mode. Note: CS must transition high
after each read/write operation. SDO is the serial data
output for reading registers to facilitate easy debugging during development. SDI and SDO can be connected together to form a 3-wire serial interface bus or
remain separate and form a 4-wire SPI bus.
The serial interface supports two-byte transfer in a
communication cycle. The first byte is a control byte
written to the MAX5893 only. The second byte is a data
byte and can be written to or read from the MAX5893.
Table 1. Quadrature Modulator Operating Data Rates (fIM is the Data Rate at the Input of
the Modulator) for Dual-Port Mode
INTERPOLATION RATE
1x
2x
4x
8x
12
MODULATION MODE (fLO)
MODULATION FREQUENCY
RELATIVE TO fDAC
MODULATION FREQUENCY
RELATIVE TO fDATA
fIM / 2
fDAC / 2
fDATA / 2
fDATA / 4
fIM / 4
fDAC / 4
fIM / 2
fDAC / 2
fDATA
fIM / 4
fDAC / 4
fDATA / 2
fIM / 2
fDAC / 2
2 x fDATA
fIM / 4
fDAC / 4
fDATA
fIM / 2
fDAC / 4
2 x fDATA
fIM / 4
fDAC / 8
fDATA
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
in first in default mode. If the serial port is set to LSBfirst mode, both the control byte and data byte are shifted
LSB in first. Figures 1 and 2 show the SPI serial interface
operation in the default write and read mode, respectively.
Figure 3 is a timing diagram for the SPI serial interface.
CS
SCLK
SDI
0
0
0
0
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
HIGH IMPEDANCE
SDO
Figure 1. SPI Serial Interface Write Cycle, MSB-First Mode
CS
READ CYCLE N
READ CYCLE N - 1
READ CYCLE N + 1
SCLK
SDI
SDO
ADDRESS
1 0 0 0 3 2 1 0
HIGH
IMPEDANCE
DATA
IGNORED
DATA N - 2
ADDRESS
1 0 0 0 3 2 1 0
HIGH
IMPEDANCE
DATA
IGNORED
DATA N - 1
ADDRESS
1 0 0 0 3 2 1 0
HIGH
IMPEDANCE
DATA
IGNORED
DATA N
Figure 2. SPI Serial Interface Read Cycle, MSB-First Mode
______________________________________________________________________________________
13
MAX5893
When writing to the MAX5893, data is shifted into SDI;
data is shifted out of SDO in a read operation. Bits 0 to
3 of the control byte are the address bits. These bits set
the address of the register to be written to or read from.
Bits 4 to 6 of the control byte must always be set to 0.
Bit 7 is a read/write bit: 0 for write operation and 1 for
read operation. The most significant bit (MSB) is shifted
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
tSS
CS
SCLK
tSDH
tSDS
SDI
tSDV
SDO
Figure 3. SPI Serial-Interface Timing Diagram
14
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
of the registers. The following are descriptions of each
register.
Table 2. MAX5893 Programmable Registers
ADD
BIT 7
BIT 6
0 = MSB first
1 = LSB first
BIT 5
BIT 4
BIT 3
Software Reset
0 = Normal
1 = Reset all
registers
Interpolator
Power-Down
0 = Normal
1 = Power-down
IDAC PowerDown
0 = Normal
1 = Power-down
Third
Interpolation
Filter
Configuration
0 = Lowpass
1 = Highpass
0 = Clock output
on DATACLK
1 = Clock output
on DATACLK/B10
BIT 2
BIT 1
QDAC PowerDown
0 = Normal
1 = Power-down
Unused
Modulation Mode
(Bit 4, Bit 3)
00 = Modulation off
01 = fIM / 2
10 = fIM / 4
11 = fIM / 4
Mixer Modulation
Mode
0 = Complex
1 = Real
Modulation
Sign
0 = e-jω
1 = e+jω
0 = Input data
latched on
rising clock
edge
1 = Input data
latched on falling
clock edge
Data
Synchronizer
0 = Enabled
1 = Disabled
Unused
BIT 0
00h
Unused
01h
Interpolation Rate
(Bit 7, Bit 6)
00 = No interpolation
01 = 2x interpolation
10 = 4x interpolation
11 = 8x interpolation
02h
0 = Two’s
complement
input data
1 = Offset
binary input
data
03h
Unused
04h
8-Bit IDAC Fine-Gain Adjustment (see the Gain Adjustment section). Bit 7 is MSB and bit 0 is LSB. Default: 00h
05h
Unused
06h
10-Bit IDAC Offset Adjustment (see the Offset Adjustment section). Bits 7 to 0 of the 06h register are the MSB bits. Bit 1 and bit 0 are the LSB
bits in 07h register. Default: 000h
0 = Single
port (A),
interleaved
I/Q
1 = Dual port
I/Q input
0 = Data clock
input enabled
1 = Data clock
output enabled
Unused
4-Bit IDAC Coarse-Gain Adjustment (see the Gain Adjustment
section). Bit 3 is MSB and bit 0 is LSB. Default: Fh
08h
IDAC IOFFSET
IDAC Offset
Direction
Adjustment
0 = Current on
Unused
Bit 1
OUTIN
(see 06h
1 = Current on
register)
OUTIP
8-Bit QDAC Fine-Gain Adjustment (see the Gain Adjustment section). Bit 7 is MSB and bit 0 is LSB. Default: 00h
09h
Unused
0Ah
10-Bit QDAC Offset Adjustment (see the Offset Adjustment section). Bits 7 to 0 of the 0Ah register are the MSB bits. Bit 1 and bit 0 are the
LSB bits in 0Bh register. Default: 000h
0Bh
QDAC
IOFFSET
Direction
0 = Current on
OUTQN
1 = Current on
OUTQP
0Ch
Reserved, do not write to these bits.
07h
IDAC Offset
Adjustment
Bit 0
(see 06h
register)
4-Bit QDAC Coarse-Gain Adjustment (see the Gain Adjustment
section). Bit 3 is MSB and bit 0 is LSB. Default: Fh
Unused
0Dh
Reserved, do not write to these bits.
0Eh
Reserved, do not write to these bits.
QDAC Offset
Adjustment
Bit 1
(see 0Ah
register)
QDAC Offset
Adjustment
Bit 0
(see 0Ah
register)
Conditions in bold are default states after reset.
______________________________________________________________________________________
15
MAX5893
Programming Registers
Programming its registers with the SPI serial interface
sets the MAX5893 operation modes. Table 2 shows all
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Address 00h
Bit 6
Logic 0 (default) causes the serial port to use
MSB first address/data format. When set to a
logic 1, the serial port will use LSB first
address/data format.
Bit 5
When set to a logic 1, all registers reset to
their default state (this bit included).
Bit 4
Logic 1 stops the clock to the digital interpolators. DAC outputs hold last value prior to
interpolator power-down.
Bit 3
IDAC power-down mode. A logic 1 to this bit
powers down the IDAC.
Bit 2
QDAC power-down mode. A logic 1 to this bit
powers down the QDAC.
Note: If both bit 2 and bit 3 are 1, the MAX5893 is in
full-power-down mode, leaving only the serial interface
active.
Address 01h
Bits 7, 6 Configure the interpolation filters according
to the following table:
00
1x (no interpolation)
01
10
11
Bit 5
2x
4x
8x (default)
Logic 0 configures FIR3 as a lowpass digital
filter (default). A logic 1 configures FIR3 as a
highpass digital filter.
Bits 4, 3 Configure the modulation frequency according to the following table:
00
No modulation
01
fIM / 2 modulation
10
fIM / 4 modulation (default)
Bit 2
Bit 1
16
11
fIM / 4 modulation
where fIM is the data rate at the input of the
modulator.
Configures the modulation mode for either
real or complex (image reject) modulation.
Logic 1 sets the modulator to the real mode
(default). Complex modulation is only available for fIM / 4 modulation.
Quadrature modulator sign inversion. With Ichannel data leading Q-channel data by 90°,
logic 0 sets the complex modulation to be
e -jw (default), cancelling the upper image
when used with an external quadrature mod-
ulator. A logic 1 sets the complex modulation
to be e+jw, cancelling the lower image when
used with an external quadrature modulator.
Address 02h
Bit 7
Logic 0 (default) configures the data port for
two’s complement. A logic 1 configures the
data ports for offset binary.
Bit 6
Logic 0 (default) configures the data bus for
single-port, interleaved I/Q data. I and Q data
enter through one 12-bit bus. Logic 1 configures the data bus for dual-port I/Q data. I and
Q data enter on separate buses.
Bit 5
Logic 0 (default) configures the data clock
for pin 14. A logic 1 configures the data clock
for pin 27 (DATACLK/B10).
Bit 4
Logic 0 (default) sets the internal latches to
latch the data on the rising edge of DATACLK.
A logic 1 sets the internal latches to latch the
data on the falling edge of DATACLK.
Logic 0 (default) configures the DATACLK
pin (pin 14 or pin 27) to be an input. A logic 1
configures the DATACLK pin to be an output.
Logic 0 (default) enables the data synchronizer circuitry. A logic 1 disables the data
synchronizer circuitry.
Bit 3
Bit 2
Address 03h
Bits 7–0 Unused.
Address 04h
Bits 7–0 These 8 bits define the binary number for
fine-gain adjustment of the IDAC full-scale
current (see the Gain Adjustment section). Bit
7 is the MSB. Default is all zeros.
Address 05h
Bits 3–0 These four bits define the binary number for
the coarse-gain adjustment of the IDAC fullscale current (see the Gain Adjustment section). Bit 3 is the MSB. Default is all ones.
Address 06h, Bits 7 to 0; Address 07h, Bit 1 and Bit 0
These 10 bits represent a binary number that
defines the magnitude of the offset added to
the IDAC output (see the Offset Adjustment
section). Default is all zeros.
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
These 10 bits represent a binary number that
defines the magnitude of the offset added to
the QDAC output (see the Offset Adjustment
section). Default is all zeros.
Address 0Bh
Bit 7
Logic 0 (default) adds the 10 bits offset to
OUTQN. A logic 1 adds the 10 bits offset to
OUTQP.
Offset Adjustment
Offset adjustment is achieved by adding a digital code
to the DAC inputs. The code OFFSET (see equation
below), as stored in the relevant control registers, has a
range from 0 to 1023 and a sign bit. The applied DAC
offset is 4 times the code stored in the register, providing an offset adjustment range of ±255 LSB codes. The
resolution is 1 LSB.
IOFFSET =
4 × OFFSET
216
× IOUTFS
Gain Trim
Gain trimming is done by varying the full-scale current
according to the following formula:
⎡⎛ 3 × IREF ⎞ ⎛ COARSE + 1⎞ ⎛ 3 × IREF ⎞ ⎛ FINE ⎞ ⎤ ⎛ 1024 ⎞
IOUTFS = ⎢⎜
⎟
⎟⎥ ⎜
⎟ −⎜
⎟⎜
⎟⎜
⎠ ⎝ 32 ⎠ ⎝ 256 ⎠ ⎦ ⎝ 24 ⎠
⎠⎝
4
16
⎣⎝
where IREF is the reference current (see the Internal
Reference section). COARSE is the register content of
registers 05h and 09h for the I- and Q-channel, respectively. FINE is the register content of register 04h and
08h for the I- and Q-channel, respectively. The range of
coarse is from 0 to 11, with 11 being the default. The
range for FINE is from 0 to 255 with 0 being the default.
Given this, the gain can be adjusted in steps of approximately 0.01dB.
Single-Port/Dual-Port Data Input Modes
The MAX5893 is capable of capturing data in singleport and dual-port modes (selected through bit 6,
address 02h). In single-port mode, the data for both
channels is input through the A port (A11–A0).
The channel for the input data is determined through
the state of the SELIQ/B11 (pin 26) bit. When SELIQ is
set to logic-high, the input data is presented to the
I-channel, when set to logic-low, the input data is
presented to the Q-channel. The unused B-port inputs
(DATACLK/B10, B9–B0) should be grounded when running in single-port mode.
Dual-port mode, as the name implies, requires that
each channel receives its data from a separate data
bus. SELIQ/B11 and DATACLK/B10 revert to data bit
inputs for the Q-channel in dual-port mode.
The MAX5893 control registers can be programmed to
allow either signed or unsigned binary format (bit 7,
address 02h) data in either single-port or dual-port
mode. Table 3 shows the corresponding DAC output
levels when using signed or unsigned data modes.
Table 3. DAC Output Code Table
DIGITAL INPUT CODE
OFFSET
BINARY
(UNSIGNED)
TWO'S
COMPLEMENT
(SIGNED)
0000 0000 0000
1000 0000 0000
0
IOUTFS
0111 1111 1111
0000 0000 0000
IOUTFS /
2
IOUTFS /
2
1111 1111 1111
0111 1111 1111
IOUTFS
0
OUT_P
OUT_N
Data Synchronization Modes
Data synchronization circuitry is provided to allow operation with an input data clock. The data clock must be
frequency locked to the DAC clock (f DAC), but can
have arbitrary phase with respect to the DAC clock.
The synchronization circuitry allows for phase jitter on
the input data clock of up to ±1 data clock cycles.
Synchronization is initially established when the reset
pin is asynchronously deasserted and the input data
clock has been running for at least 4 clock cycles.
Subsequently, the MAX5893 monitors the phase rela-
______________________________________________________________________________________
17
MAX5893
Address 07h
Bit 7
Logic 0 (default) adds the 10 bits offset current to OUTIN. A logic 1 adds the 10 bits offset current to OUTIP.
Address 08h
Bits 7–0 These 8 bits define the binary number for
fine-gain adjustment of the QDAC full-scale
current (see the Gain Adjustment section). Bit
7 is the MSB. Default is all zeros.
Address 09h
Bits 3–0 These four bits define the binary number for
the coarse-gain adjustment of the QDAC fullscale current (see the Gain Adjustment section). Bit 3 is the MSB. Default is all ones.
Address 0Ah, Bits 7 to 0; Address 0Bh, Bit 1 and Bit 0
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
tionship and detects if the phase drifts more than ±1
data clock cycle. If this occurs, the synchronizer automatically reestablishes synchronization. However, during the resynchronization phase, up to 8 data words
may be lost or repeated.
Bit 2 of register 02h disables or enables (default) the
automatic data clock phase detection. Disabling the
data synchronization circuitry requires the data clock
and the DAC clock phase to be locked.
Table 4. Clock Frequency Ratios in
Various Modes
INPUT
MODE
INTERPOLATION
RATE
fDATA:fCLK
fDAC:fCLK
1x
1:1
1:2
2x
1:1
1:1
4x
1:2
1:1
DATACLK Modes
8x
1:4
1:1
The MAX5893 has a main DATACLK available at
pin 14. An alternate DATACLK is available at pin 27
(DATACLK/B10) when configured in single-port data
input mode (bit 5, address 02h). The DATACLK can be
configured to accept an input clock signal for latching
the input data, or to source a clock signal that can drive
up to 10pF load while latching the input data (bit 3,
address 02h). If DATACLK is configured as an output, it
is frequency divided from the CLKP/CLKN input,
depending on the operating mode, see Table 4.
1x
1:1
1:1
2x
1:2
1:1
4x
1:4
1:1
8x
1:8
1:1
Single
Port
Dual Port
The MAX5893 can be configured to latch the input
data on either the rising edge or falling edge of the
DATACLK signal (bit 4, address 02h). Figure 4 shows
the timing requirements between the DATACLK signal
and the input data bus with latching on the rising edge.
CLKP–CLKN
tCLK
DATACLK
tD
tDS
tDH
A0–A11/B0–B11
Figure 4. Data Input Timing Diagram
18
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
0
0
-20
-20
PASSBAND DETAIL
-40
0
GAIN (dBFS)
GAIN (dBFS)
ter is located after the modulator. In the 8x interpolation
mode, the last filter (FIR3) can be configured as lowpass or highpass (bit 5, address 01h) to select the
lower or upper sideband from the modulation output.
The frequency responses of these three filters are plotted in Figures 5–8.
-0.0002
-60
-0.0004
0.4
0.3
0.2
0.1
0
MAX5893
Interpolating Filter
The MAX5893 features three cascaded FIR half-band
filters. The interpolating filters are enabled or disabled
in combinations to support 1x (no interpolation), 2x, 4x,
or 8x interpolation. Bits 7 and 6 of register 01h set the
interpolation rate (see Table 2). The last interpolation fil-
PASSBAND DETAIL
-40
0
-0.0002
-60
-0.0004
0
-80
-80
-100
-100
0.1
0.2
0.3
2.0
2.5
0.4
-120
-120
0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.5
1.0 1.5
3.0 3.5
4.0
fOUT - NORMALIZED TO INPUT DATA RATE
fOUT - NORMALIZED TO INPUT DATA RATE
Figure 5. Interpolation Filter Frequency Response, 2x
Interpolation Mode
Figure 6. Interpolation Filter Frequency Response, 4x
Interpolation Mode
0
0
0
-0.0002
-20
PASSBAND DETAIL
-40
0
GAIN (dBFS)
GAIN (dBFS)
-20
-0.0002
-60
-0.0004
0.1
0
0.2
0.3
0.4
-40
-0.0004
-0.0002
-60
-0.0004
-80
-80
-100
-100
-120
PASSBAND DETAIL
0
3.6
3.8
4.0
4.2
4.4
-120
0
1
2
3
4
5
6
7
8
fOUT - NORMALIZED TO INPUT DATA RATE
Figure 7. Interpolation Filter Frequency Response, 8x
Interpolation Mode (FIR3 Lowpass Mode)
0
1
2
3
4
5
6
7
8
fOUT - NORMALIZED TO INPUT DATA RATE
Figure 8. Interpolation Filter Frequency Response, 8x
Interpolation Mode (FIR3 Highpass Mode)
______________________________________________________________________________________
19
0
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
The programmable interpolation filters multiply the
MAX5893 input data rate by a factor of 2x, 4x, or 8x to
separate the reconstructed waveform spectrum and the
DAC image. The original spectral images, appearing at
around multiples of the input data rate, are attenuated
by the internal digital filters. This feature provides three
benefits:
1) Image separation reduces complexity of analog
reconstruction filters.
INPUT
SPECTRUM
AND FIRST
FILTER
RESPONSE
SIGNAL
OUTPUT
SPECTRUM
OF THE
FIRST
FILTER
4fS
5fS
6fS
7fS
8fS
2x INTERPOLATION
3fS
4fS
5fS
2fS
6fS
7fS
8fS
6fS
7fS
8fS
FILTER
RESPONSE
IMAGE
3fS
4fS
5fS
SIGNAL
4x INTERPOLATION
IMAGE
2fS
3fS
4fS
SIGNAL
2fS
3fS
5fS
6fS
7fS
8fS
5fS
6fS
7fS
8fS
IMAGE
FILTER
RESPONSE
fS
OUTPUT
SPECTRUM
OF THE
THIRD
FILTER
2fS
SIGNAL
fS
INPUT
SPECTRUM
AND THIRD
FILTER
RESPONSE
3fS
NO INTERPOLATION
IMAGE
fS
OUTPUT
SPECTRUM
OF THE
SECOND
FILTER
2fS
SIGNAL
fS
INPUT
SPECTRUM
AND
SECOND
FILTER
RESPONSE
Figure 9 illustrates a practical example of the benefits
when using the MAX5893 in 2x, 4x, and 8x interpolation
modes with the third filter configured as a lowpass filter.
With no interpolation filter, the first image signal appears
in the second Nyquist zone between fS / 2 and fS. The first
interpolating filter removes this image. In fact, all of the
FILTER
RESPONSE
IMAGE
fS
2) Lower input data rates eliminate board-level highspeed data transmission.
3) Sin(x)/x rolloff is reduced over the effective bandwidth.
4fS
SIGNAL
8x INTERPOLATION
IMAGE
fS
2fS
3fS
4fS
5fS
6fS
7fS
8fS
Figure 9. Spectral Representation of Interpolating Filter Responses (Output Frequencies are Relative to the Data Input Frequency, fS)
20
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
INPUT
SPECTRUM
AND FIRST
FILTER
RESPONSE
SIGNAL
FILTER
RESPONSE
IMAGE
2fS
fS
OUTPUT
SPECTRUM
OF THE
FIRST
FILTER
SIGNAL
SIGNAL
FILTER
RESPONSE
4fS
2x INTERPOLATION
3fS
4fS
3fS
4fS
IMAGE
2fS
SIGNAL
4x INTERPOLATION
IMAGE
fS
OUTPUT
SPECTRUM
OF THE
MODULATOR
3fS
2fS
fS
OUTPUT
SPECTRUM
OF THE
SECOND
FILTER
NO INTERPOLATION
IMAGE
fS
INPUT
SPECTRUM
AND
SECOND
FILTER
RESPONSE
12fS, 20fS, etc. Figures 10, 11, and 12 similarly illustrate
the spectral responses when using the interpolating filters
combined with the digital modulator.
LOWER
SIDEBAND
SIGNAL
fS
2fS
3fS
UPPER
SIDEBAND
4fS
IMAGE
2fS
3fS
4fS
FOR COMPLEX MODULATION THE MODULATION SIGN (BIT 1, ADDRESS 01h) SELECTS UPPER OR LOWER SIDEBAND
Figure 10. Spectral Representation of 4x Interpolation Filter with fIM / 4 Modulation (Output Frequencies are Relative to the Data Input
Frequency, fS)
______________________________________________________________________________________
21
MAX5893
images at odd numbers of fS are filtered. At the output of
the first filter, the images are at 2fS, 4fS, etc. This signal is
then passed to the second interpolating filter, which is
similar to the first filter and removes the images at 2fS, 6fS,
10fS, etc. Finally, the third filter removes images at 4fS,
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
INPUT
SPECTRUM
AND FIRST
FILTER
RESPONSE
SIGNAL
fS
OUTPUT
SPECTRUM
OF THE
FIRST
FILTER
2fS
SIGNAL
SIGNAL
4fS
5fS
6fS
7fS
8fS
2x INTERPOLATION
3fS
4fS
2fS
5fS
6fS
7fS
8fS
5fS
6fS
7fS
8fS
FILTER
RESPONSE
IMAGE
3fS
4fS
SIGNAL
4x INTERPOLATION
IMAGE
fS
OUTPUT
SPECTRUM
OF THE
MODULATOR
3fS
2fS
fS
OUTPUT
SPECTRUM
OF THE
SECOND
FILTER
NO INTERPOLATION
IMAGE
fS
INPUT
SPECTRUM
AND
SECOND
FILTER
RESPONSE
FILTER
RESPONSE
IMAGE
LOWER
SIDEBAND
2fS
3fS
SIGNAL
UPPER
SIDEBAND
4fS
5fS
6fS
fS
8fS
7fS
8fS
IMAGE
2fS
3fS
4fS
5fS
6fS
SIGNAL
OUTPUT
SPECTRUM
OF THE
THIRD
FILTER
7fS
FILTER RESPONSE
SIGNAL
fS
8fS
IMAGE
fS
2fS
3fS
4fS
5fS
6fS
FOR COMPLEX MODULATION THE MODULATION SIGN (BIT 1, ADDRESS 01h) SELECTS UPPER OR LOWER SIDEBAND
INPUT
SPECTRUM
AND THIRD
FILTER
RESPONSE
7fS
8x INTERPOLATION
IMAGE
2fS
3fS
4fS
5fS
6fS
7fS
8fS
Figure 11. Spectral Representation of 8x Interpolation Filter with fIM / 4 Modulation and Lowpass Mode Enabled (Output Frequencies
are Relative to the Data Input Frequency, fS)
22
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
fS
OUTPUT
SPECTRUM
OF THE
FIRST
FILTER
2fS
SIGNAL
2fS
SIGNAL
2fS
5fS
6fS
7fS
8fS
2x INTERPOLATION
3fS
4fS
5fS
6fS
7fS
8fS
6fS
7fS
8fS
FILTER
RESPONSE
3fS
4fS
5fS
SIGNAL
4x INTERPOLATION
IMAGE
fS
OUTPUT
SPECTRUM
OF THE
MODULATOR
4fS
IMAGE
fS
OUTPUT
SPECTRUM
OF THE
SECOND
FILTER
3fS
NO INTERPOLATION
IMAGE
fS
INPUT
SPECTRUM
AND
SECOND
FILTER
RESPONSE
FILTER
RESPONSE
IMAGE
LOWER
SIDEBAND
2fS
3fS
SIGNAL
UPPER
SIDEBAND
4fS
5fS
6fS
SIGNAL
fS
8fS
7fS
8fS
7fS
8fS
FILTER
RESPONSE
IMAGE
2fS
3fS
4fS
5fS
SIGNAL
OUTPUT
SPECTRUM
OF THE
THIRD
FILTER
fS
7fS
IMAGE
fS
2fS
3fS
4fS
5fS
6fS
FOR COMPLEX MODULATION THE MODULATION SIGN (BIT 1, ADDRESS 01h) SELECTS UPPER OR LOWER SIDEBAND
INPUT
SPECTRUM
AND THIRD
FILTER
RESPONSE
MAX5893
INPUT
SPECTRUM
AND FIRST
FILTER
RESPONSE
SIGNAL
2fS
3fS
6fS
8x INTERPOLATION
IMAGE
4fS
5fS
6fS
7fS
8fS
Figure 12. Spectral Representation of 8x Interpolation Filter with fIM / 4 Modulation and Highpass Mode Enabled (Output Frequencies
are Relative to the Data Input Frequency, fS)
______________________________________________________________________________________
23
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Digital Modulator
The MAX5893 features digital modulation at frequencies of fIM / 2 and fIM / 4, where fIM is the data rate at
the input to the modulator. fIM equals fDAC in 1x, 2x,
and 4x interpolation modes. In 8x interpolation mode,
fIM equals fDAC / 2. The output rate of the modulator is
always the same as the input data rate to the modulator, fIM.
In complex modulation mode, data from the second
interpolation filter is frequency mixed with the on-chip
in-phase and quadrature (I/Q) local oscillator (LO).
Complex modulation provides the benefit of image
sideband rejection when combined with an external
quadrature modulator commonly found in wireless
communication systems.
In the fLO = fIM / 4 mode, real or complex modulation
can be used. The modulator multiplies successive input
data samples by the sequence [1, 0, -1, 0] for a cos(ωt).
The modulator modulates the input signal up to fIM / 4,
creating upper and lower images around fIM / 4. The
quadrature LO sin(ωt) is realized by delaying the cos(ωt)
sequence by one clock cycle. Using complex modulation, complex IF is generated. The complex IF combined
with an external quadrature modulator provides image
rejection. The sign of the LO can be changed to allow
the user to select whether the upper or the lower image
should be rejected (bit 1 of register 01h).
When fIM / 2 is chosen as the LO frequency, the input
signal is multiplied by [-1, 1] on both channels. This produces images around fIM / 2. The complex image-reject
modulation mode is not available for this LO frequency.
I-CHANNEL
INPUT DATA
The outputs of the modulator can be expressed as:
I (t) = A(t) × cos(ωt) − B(t) × sin(ωt)
Q (t) = A(t) × sin(ωt) + B(t) × cos(ωt)
in complex modulation, e+jwt
I (t) = A(t) × cos(ωt) + B(t) × sin(ωt)
Q (t) = A(t) × sin(ωt) + B(t) × cos(ωt)
in complex modulation, e-jwt
where ω = 2 x π x fLO.
For real modulation, the outputs of the modulator can
be expressed as:
I (t) = A(t) × cos(ωt)
Q (t) = A(t) × cos(ωt)
If more than one MAX5893 is used, their LO phases
can be synchronized by simultaneously releasing
RESET. This sets the MAX5893 to its predefined initial
phase.
Device Reset
The MAX5893 can be reset by holding the RESET pin
low for 10ns. This will program the control registers to
their default values in Table 2. During power-on, RESET
must be held low until all power supplies have stabilized. Alternately, programming bit 5 of address 00h to
a logic-high also resets the MAX5893 after power-up.
I-CHANNEL
INPUT DATA
∑
cos(ωt)
sin(ωt)
I-CHANNEL
OUTPUT DATA
cos(ωt)
TO
FIR3
sin(ωt)
sin(ωt)
∑
I-CHANNEL
OUTPUT DATA
TO
FIR3
sin(ωt)
∑
Q-CHANNEL
INPUT DATA
∑
Q-CHANNEL
OUTPUT DATA
Q-CHANNEL
OUTPUT DATA
Q-CHANNEL
INPUT DATA
cos(ωt)
cos(ωt)
(a)
(b)
Figure 13. (a) Modulator in Complex Modulation Mode; (b) Modulator in Real Modulation Mode
24
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Data Clock
The MAX5893 features synchronizers that allow for
arbitrary phase alignment between DATACLK and
CLKP/CLKN. The DATACLK causes internal switching
in the MAX5893 and the phase between DATACLK
(input mode) to CLKP/CLKN will influence the images
at DATACLK. Optimum image rejection is achieved
when DATACLK transitions are aligned with the falling
edge of CLKP. Figure 14 shows the image level near
DATACLK as a function of the DATACLK (input mode)
to CLKP/CLKN phase at 500Msps, 4x interpolation for a
10MHz, -6dBFS output signal.
Frequency Planning
System designers need to take the DAC into account
during frequency-planning for high-performance applications. Proper frequency planning can ensure that
optimal system performance is achieved. The
MAX5893 is designed to deliver excellent dynamic performance across wide bandwidths, as required for
communication systems. As with all DACs, some combinations of output frequency and update rate produce
better performance than others.
Harmonics are often folded down into the band of interest. Specifically, if the DAC outputs a frequency close
to fS / N, the Mth harmonic of the output signal will be
aliased down to:
⎡N − M ⎤
f = fS − M × fOUT = fS ⎢
⎥
⎣ N ⎦
Thus, if N ≈ (M + 1), the Mth harmonic will be close to
the output frequency. SFDR performance of a currentsteering DAC is often dominated by third-order harmonic distortion. If this is a concern, placing the output
signal at a different frequency other than fS / 4 should
be considered.
Common to interpolating DACs are images near the
divided clocks. In a DAC configured for 4x interpolation
this applies to images around fS / 4 and fS / 2. In a DAC
configured for 8x interpolation this applies to images
around fS / 8, fS / 4, and fS / 2. Most of these images
are not part of the in-band (0 to fDATA / 2) SFDR specification, though they are a consideration for out-of-band
(fDATA / 2 - fDAC / 2) SFDR and may depend on the
relationship of the DATACLK to DAC update clock (see
the Data Clock section). When specifying the output
reconstruction filter for other than baseband signals,
these images should not be ignored.
Clock Interface
The MAX5893 features a flexible differential clock input
(CLKP, CLKN) with a separate supply (AV CLK ) to
achieve optimum jitter performance. It uses an ultra-low
jitter clock to achieve the required noise density. Clock
jitter must be less than 0.5psRMS to meet the specified
noise density. For that reason, the CLKP/CLKN input
source must be designed carefully. The differential
clock (CLKN and CLKP) input can be driven from a single-ended or a differential clock source. Differential
clock drive is required to achieve the best dynamic
performance from the DAC. For single-ended operation, drive CLKP with a low noise source and bypass
CLKN to GND with a 0.1µF capacitor.
The CLKP and CLKN pins are internally biased to
AVCLK / 2. This allows the user to AC-couple clock
fS / 4 IMAGES vs. CLKP/CLKN to DATACLK DELAY
fDATA = 125MWps, 4x INTERPOLATION
-50
-60
IMAGE LEVEL (dBc)
Applications Information
fS / 4 - fOUT
-70
-80
-90
fS / 4 + fOUT
-100
fOUT = 10MHz
AOUT = -6dBFS
-110
0
2.0
4.0
6.0
8.0
CLKP/CLKN DELAY (ns)
Figure 14. Effect of CLKP/CLKN to DATACLK Phase on fS / 4
Images
______________________________________________________________________________________
25
MAX5893
Power-Down Mode
The MAX5893 features three power-saving modes.
Each DAC can be individually powered down through
bits 2 and 3 of address 00h. The interpolation filters can
also be powered down through bit 4 of address 00h,
preserving the output level of each DAC (the DACs
remain powered). Powering down both DACs will automatically put the MAX5893 into full power-down, including the interpolation filters.
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
sources directly to the device without external resistors
to define the DC level. The input resistance of CLKP
and CLKN is 5kΩ.
A convenient way to apply a differential signal is with a
balun transformer as shown in Figure 15. Alternatively,
these inputs may be driven from a CMOS-compatible
clock source, however it is recommended to use
sine-wave or AC-coupled differential ECL/PECL drive for
best dynamic performance.
Output Interface (OUTI, OUTQ)
The MAX5893 outputs complementary currents (OUTIP,
OUTIN) and (OUTQP, OUTQN), that can be utilized in a
differential configuration. Load resistors convert these
two output currents into a differential output voltage.
The differential output between OUTIP (OUTQP) and
OUTIN (OUTQN) can be converted to a single-ended
output using a transformer or a differential amplifier.
Figure 16 shows a typical transformer-based application circuit for generation of IF output signals. In this
configuration, the MAX5893 operates in differential
mode, which reduces even-order harmonics, and
increases the available output power. Pay close attention to the transformer core saturation characteristics
when selecting a transformer. Transformer core saturation can introduce strong second harmonic distortion,
especially at low output frequencies and high signal
100nF
CLKP
SINGLE-ENDED
IINPUT
MINI-CIRCUITS
ADTL1-12
24.9Ω
MAX5893
1:1 RATIO
24.9Ω
100nF
CLKN
Figure 15. Single-Ended-to-Differential Clock Conversion Using
a Balun Transformer
50Ω
1:1
OUTIP
IDAC
VIOUT, SINGLE-ENDED
100Ω
12
1:1
OUTIN
50Ω
MAX5893
50Ω
1:1
OUTQP
QDAC
VQOUT, SINGLE-ENDED
100Ω
12
1:1
OUTQN
50Ω
Figure 16. Differential-to-Single-Ended Conversion Using Wideband RF Transformers
26
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
If a transformer is not used, the outputs must have a
resistive termination to ground. Figure 17 shows the
MAX5893 output configured for differential DC-coupled
mode. The DC-coupled configuration can be used to
eliminate waveform distortion due to highpass filter
effects. Applications include communication systems
employing analog quadrature upconverters and requiring a high-speed DAC for baseband I/Q synthesis.
If a single-ended DC-coupled unipolar output is desirable, OUTIP (OUTQP) should be selected as the output, and connect OUTIN (OUTQN) to ground. Using the
MAX5893 output single-ended is not recommended
because it introduces additional noise and distortion.
The distortion performance of the DAC also depends
on the load impedance. The MAX5893 is optimized for
a 50Ω double termination. It can be used with a transformer output as shown in Figure 16 or just one 25Ω
resistor from each output to ground and one 50Ω resistor between the outputs (Figure 17). Higher output termination resistors may be used, as long as each output
voltage does not exceed +1V with respect to GND, but
at the cost of degraded distortion performance and
increased output noise voltage.
MAX5893
amplitudes. It is recommended to connect the transformer center tap to ground.
25Ω
OUTIP
IDAC
50Ω
12
OUTIN
25Ω
MAX5893
25Ω
OUTQP
QDAC
50Ω
12
OUTQN
25Ω
Reference Input/Output
The MAX5893 supports operation with the on-chip 1.2V
bandgap reference or an external reference voltage
source. REFIO serves as the input for an external, lowimpedance reference source, and as the output if the
DAC is operating with the internal reference.
Figure 17. The DC-Coupled Differential Output Configuration
______________________________________________________________________________________
27
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
For stable operation with the internal reference, REFIO
should be decoupled to GND with a 1µF capacitor.
REFIO must be buffered with an external amplifier, if
heavy loading is required, due to its 10kΩ output resistance.
Alternatively, apply a temperature-stable external reference to REFIO (Figure 18). The internal reference is overdriven by the external reference. For improved accuracy
and drift performance, choose a fixed output voltage reference such as the MAX6520 bandgap reference.
The MAX5893’s reference circuit (Figure 19) employs a
control amplifier, designed to regulate the full-scale
current IOUT for the differential current outputs of the
DAC. The output current can be calculated as:
IOUTFS = 32 x IREFIO - 1LSB
IOUTFS = 32 x IREFIO - (IOUT / 212)
where IREFIO is the reference output current (IREFIO =
VREFIO / RSET) and IOUT is the full-scale output current
of the DAC. Located between FSADJ and DACREF,
RSET is the reference resistor, which determines the
amplifier’s output current for the DAC. Use Table 5 for a
matrix of different IOUTFS and RSET selections.
1.2V
REFERENCE
1.2V
REFERENCE
MAX5893
MAX5893
10kΩ
10kΩ
EXTERNAL
1.25V
REFERENCE
REFIO
REFIO
1µF
1µF
FSADJ
FSADJ
CURRENTSOURCE
ARRAY DAC
IREF
RSET
CURRENTSOURCE
ARRAY DAC
IREF
RSET
DACREF
DACREF
Figure 18. Typical External Reference Circuit
Figure 19. MAX5893 Internal Reference Architecture
Table 5. IOUTFS and RSET Selection Matrix Based on a Typical 1.20V Reference Voltage
FULL-SCALE
CURRENT
REFERENCE
CURRENT
IOUTFS (mA)
IREF (µA)
CALCULATED
1% EIA STD
VIOUTP/N* (mVP-P)
2
62.50
19.2k
19.1k
100
5
156.26
7.68k
7.5k
250
10
312.50
3.84k
3.83k
500
15
468.75
2.56k
2.55k
750
20
625.00
1.92k
1.91k
1000
RSET (Ω)
OUTPUT VOLTAGE
*Terminated into a 50Ω load.
28
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
Grounding and power-supply decoupling strongly influence the MAX5893 performance. Unwanted digital
crosstalk can couple through the input, reference,
power-supply, and ground connections, which can
affect dynamic specifications like signal-to-noise ratio
or spurious-free dynamic range. In addition, electromagnetic interference (EMI) can either couple into or
be generated by the MAX5893. Observe the grounding
and power-supply decoupling guidelines for highspeed, high-frequency applications. Follow the powersupply and filter configuration guidelines to achieve
optimum dynamic performance.
Using a multilayer printed circuit (PC) board with separate ground and power-supply planes, run high-speed
signals on lines directly above the ground plane. Since
the MAX5893 has separate analog and digital sections,
the PC board should include separate analog and digital ground sections with only one point connecting the
three planes at the exposed paddle under the
MAX5893. Run digital signals above the digital ground
plane and analog/clock signals above the analog/clock
ground plane. Keep digital signals as far away from
sensitive analog inputs, reference lines, and clock
inputs as practical. Use a symmetric design of clock
input and the analog output lines to minimize 2nd-order
harmonic distortion components, thus optimizing the
dynamic performance of the DAC. Keep digital signal
paths short and run lengths matched to avoid propagation delay and data skew mismatches.
The MAX5893 requires five separate power-supply
inputs for the analog (AVDD1.8 and AVDD3.3), digital
(DVDD1.8 and DVDD3.3), and clock (AVCLK) circuitry.
Decouple each voltage supply pin with a separate
0.1µF capacitor as close to the device as possible and
with the shortest possible connection to the appropriate
ground plane. Minimize the analog and digital load
capacitances for optimized operation. Decouple all
power-supply voltages at the point they enter the PC
board with tantalum or electrolytic capacitors. Ferrite
beads with additional decoupling capacitors forming a
pi-network could also improve performance.
The exposed paddle (EP) MUST be soldered to the
ground. Use multiple vias, an array of at least 4 x 4
vias, directly under the EP to provide a low thermal and
electrical impedance path for the IC.
Static Performance Parameter
Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from either a best straight-line fit
(closest approximation to the actual transfer curve) or a
line drawn between the end points of the transfer function, once offset and gain errors have been nullified.
For a DAC, the deviations are measured at every individual step.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step height and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function.
Offset Error
The offset error is the difference between the ideal and
the actual offset current. For a DAC, the offset point is
the average value at the output for the two midscale
digital input codes with respect to the full-scale of the
DAC. This error affects all codes by the same amount.
Gain Error
A gain error is the difference between the ideal and the
actual full-scale output voltage on the transfer curve,
after nullifying the offset error. This error alters the slope
of the transfer function and corresponds to the same
percentage error in each step.
Dynamic Performance
Parameter Definitions
Settling Time
The settling time is the amount of time required from the
start of a transition until the DAC output settles its new
output value to within the specified accuracy.
Noise Spectral Density
The DAC output noise is the sum of the quantization
noise and thermal noise. Noise spectral density is the
noise power in 1Hz bandwidth, specified in dBFS/Hz.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog output (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
maximum SNR can be derived from the DAC’s resolution (N bits):
SNRdB = 6.02dB x N + 1.76dB
______________________________________________________________________________________
29
MAX5893
Power Supplies, Bypassing,
Decoupling, and Layout
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
However, noise sources such as thermal noise, reference noise, clock jitter, etc. affect the ideal reading.
Therefore, SNR is computed by taking the ratio of the
RMS signal to the RMS noise, which includes all spectral components minus the fundamental, the first four
harmonics, and the DC offset.
Two-/Four-Tone Intermodulation
Distortion (IMD)
The two-tone IMD is the ratio expressed in dBc (or
dBFS) of the worst 3rd-order (or higher) IMD products
to either output tone.
Spurious-Free Dynamic Range (SFDR)
Adjacent Channel Leakage
Power Ratio (ACLR)
SFDR is the ratio of the RMS amplitude of the carrier
frequency (maximum signal components) to the RMS
value of their next largest distortion component. SFDR
is usually measured in dBc and with respect to the carrier frequency amplitude or in dBFS with respect to the
DAC’s full-scale range. Depending on its test condition,
SFDR is observed within a predefined window or
to Nyquist.
Commonly used in combination with WCDMA (wideband code-division multiple-access), ACLR reflects the
leakage power ratio in dB between the measured powers within a channel relative to its adjacent channel.
ACLR provides a quantifiable method of determining
out-of-band spectral energy and its influence on an
adjacent channel when a bandwidth-limited RF signal
passes through a nonlinear device.
30
______________________________________________________________________________________
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
63 62 61 60 59 58
AVDD1.8
FSADJ
GND
AVDD3.3
GND
OUTQN
OUTQP
GND
AVDD3.3
GND
OUTIN
GND
67 66 65 64
OUTIP
AVDD3.3
AVDD1.8
68
GND
AVCLK
TOP VIEW
57 56 55 54 53 52
EXPOSED PADDLE
CLKP
1
CLKN
2
50 REFIO
N.C.
3
49 RESET
N.C.
4
48 CS
N.C.
5
47 SCLK
DVDD1.8
6
46 SDI
A11
7
45 SDO
A10
8
A9
9
51 DACREF
44 DVDD3.3
MAX5893
43 N.C.
A8 10
42 N.C.
A7 11
41 N.C.
A6 12
DVDD3.3 13
40 N.C.
39 B0
DATACLK 14
38 B1
A5 15
37 DVDD1.8
A4 16
36 B2
A3 17
35 B3
B4
B5
B6
B7
DVDD1.8
B8
B9
DATACLK/B10
SELIQ/B11
N.C.
N.C.
N.C.
N.C.
DVDD1.8
A0
A1
A2
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
QFN
______________________________________________________________________________________
31
MAX5893
Pin Configuration
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
68L QFN.EPS
MAX5893
12-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
PACKAGE OUTLINE, 68L QFN, 10x10x0.9 MM
1
C
21-0122
2
PACKAGE OUTLINE, 68L QFN, 10x10x0.9 MM
1
C
21-0122
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
32 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.