CS3706 CS3706 Dual Output Driver Description Features The CS3706 integrated circuit provides an interface between lowlevel TTL inputs and high-power switching devices such as power MOSFETs. A typical application is single-ended PWM control to pushpull power control conversion. source or sink up to 1.5A. An internal flip-flop, driven by doublepulse suppression logic, can be enabled to provide single-ended to push-pull conversion. With the flipflop disabled, the outputs work in parallel for 3.0A capability. The primary function of this device is to convert a bipolar single-ended low current digital input to a pair of totem pole outputs which can Protection functions are also included for pulse-by-pulse current limiting, automatic deadband control and thermal shutdown. Block Diagram +5V Toggle Q Flip T Flop Q F/F Enable INHIBIT A -A 16 Lead PDIP +5V +5V V OUTA A Ou tp ut L o g ic Inh Am p +B +5V Inh Am p - INHIBIT B INV +5V +5V +5V B Ou tp ut L o g ic Digital Input Logic NONINV +5V V OUT B Logic Thermal Voltage Regulator Shutdown V IN Package Options V CC + INHIBIT REF ■ Dual 1.5A Totem Pole Outputs ■ 40nsec Rise and Fall into 1000pF ■ Parallel or Push-Pull Operation ■ Single-Ended to Push-Pull Conversion ■ High-Speed Power MOSFET Compatible ■ Low Cross-Conduction Current Spike ■ Analog Latched Shutdown ■ Internal Deadband Inhibit Circuit ■ Low Quiescent Current ■ 5V to 40V Operation ■ Thermal Shutdown Protection (Internally Fused Leads) INHIBIT B 1 16 INHIBIT A INV 2 15 INHIBIT REF NONINV 3 14 VIN Gnd 4 13 Gnd Gnd 5 12 Gnd VOUTA 6 11 VOUTB F/F ENABLE 7 10 STOP + VCC 8 9 STOP - +5V 130mV STOP + +V IN S to p Amp R S Note: All Four Ground Pins must be Connected to Common Ground. Analog Stop Latch Gnd STOP - ON Semiconductor 2000 South County Trail, East Greenwich, RI 02818 Tel: (401)885–3600 Fax: (401)885–5786 N. American Technical Support: 800-282-9855 Web Site: www.cherry–semi.com April, 1999 - Rev. 1 1 CS3706 Absolute Maximum Ratings Logic Supply Voltage (VIN) ...................................................................................................................................................40.0V Output Supply Voltage (VCC) ...............................................................................................................................................40.0V Output Current (each output, source, or sink) Steady State ...............................................................................................................................................................±500mA Peak Transient for Less Than 100µs ...........................................................................................................................±1.5A Capacitive Discharge Energy ......................................................................................................................................20.0µJ Digital Inputs (INV, NONINV) ..............................................................................................................................................5.5V Analog Inputs (STOP +, STOP -) ............................................................................................................................................VIN Inhibit Inputs (INHIBIT A, INHIBIT B, INHIBIT REF)......................................................................................................5.5V Operating Temperature Range .......................................................................................................................................0 to 70˚C Storage Temperature Range.......................................................................................................................................-65 to 150˚C Lead Temperature Soldering Wave Solder (through hole styles only).....................................................................................10 sec. max, 260°C peak Notes: All voltages are with respect to the four ground pins which must be connected together. All currents are positive into, negative out of the specified terminal. Electrical Characteristics: These specifications apply over the operating temperature range of the IC. (VIN = VCC = 20V, Pins 4, 5, 12 &13 = 0V; unless otherwise stated.) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VIN Supply Current VIN = 40V, VCC = 20V, INV = 0V, Unused pins = open. 8 12 mA VCC Supply Current VIN = 20V, VCC = 40V, Outputs low 3 5 mA VCC Leakage Current VIN = 0V, VCC = 40V 0.05 Digital Input Low Level Digital Input High Level 0.10 mA 0.8 V 2.2 V Digital Input Current VI = 0V -0.6 -1.0 mA Digital Input Leakage VI = 5V 0.05 0.10 mA Output High Sat., VC-VOUT IOUT = -50mA 2.0 V Output High Sat., VC-VOUT IOUT = -500mA 2.5 V Output Low Sat., VOUT IOUT = 50mA 0.4 V 2.5 V 0.6 V Output Low Sat., VOUT IOUT = 500mA Inhibit Threshold VREF = 0.5V 0.4 Inhibit Threshold VREF = 3.5V 3.3 Inhibit Input Current VREF = 0V Analog Threshold VCM = 0V to 15 V 100 3.7 V -10 -20 µA 130 150 mV -20 Analog Input Bias Current VI = 0V, VCM = 15V -10 Thermal Shutdown Turn on 155 ˚C Thermal Shutdown Turn off 125 ˚C 2 µA PARAMETER TEST CONDITIONS OUTPUT CL = UNIT From Inv. Input to Output: Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall open 110 20 80 25 1.0 130 40 90 30 2.2 140 60 110 50 nF ns ns ns ns From N.I. Input to Output: Rise Time Delay 10% to 90% Rise Fall Time Delay 90% to 10% Fall 120 20 100 25 130 40 120 30 140 60 130 50 ns ns ns ns VC Cross-Conduction Current Spike Duration Output Rise Output Fall 25 0 ns ns Inhibit Delay Inhibit Ref. = 1V Inhibit = 0.5 to 1.5V 250 ns Analog Shutdown Delay Stop (+) Ref. = 0 Stop (-) Input = 0 to 0.5V 180 ns Package Pin Description PACKAGE PIN # PIN SYMBOL FUNCTION 16L PDIP (Internally Fused Leads) 1 INHIBIT B Control pin for deadband control on Channel B. 2 INV 3 NONINV 4 5 6 Gnd Gnd VOUT(A) 7 F/F ENABLE 8 VCC 9 STOP - Inverting input for stop latch comparator. 10 STOP + Noninverting input for stop latch comparator. 11 VOUT(B) Channel B output. 12 Gnd Ground. 13 Gnd Ground. 14 VIN Supply voltage (5V to 40V) for IC (except output driver). 15 INHIBIT REF 16 INHIBIT A Inverting input for output drivers. Noninverting input for output drivers. Ground. Ground. Channel A output. Controls the phase of the two outputs. F/F ENABLE = Gnd Out of phase. F/F ENABLE = floating In phase. Supply voltage (5V to 40V) for output drivers. Reference input for deadband control. Control pin for deadband control on channel A. 3 CS3706 Typical Switching Characteristics: (VIN = VCC = 20V, TA = 25˚C. Delays measured 50% in to 50% out.) CS3706 Circuit Description Outputs The totem-pole outputs have been designed to minimize cross-conduction current spikes while maximizing fast, high-current rise and fall times. Current limiting can be done externally either at the outputs or at the common VCC pin. The output diodes included have slow recovery and should be shunted with high-speed external diodes when driving high-frequency inductive loads. Analog Shutdown This circuit is included to get a latched shutdown as close to the outputs as possible, from a time standpoint. With an internal 130mV threshold, this comparator has a commonmode range from ground to (VIN - 3V). When not used, both inputs should be grounded. The time required for this circuit to latch is inversely proportional to the amount of overdrive but reaches a minimum of 180nsec. As with the flip-flop, an input off-time of at least 200nsec is required to reset the latch between pulses. Flip/Flop Grounding F/F Enable activates the internal flip-flop to alternate the two outputs. With pin open, the two outputs operate simultaneously and can be paralleled for higher current operation. Since the flip-flop is triggered by the digital input, an off-time of at least 200nsec. must be provided to allow the flip/flop to change states. Note that the circuit logic is configured such that the “OFF” state is defined as the outputs low. Supply Voltage With an internal 5V regulator, this circuit is optimized for use with a 7 to 40V supply, however, with some slight response time degradation, it can also be driven from 5V. When VIN is low, the entire circuit is disabled and no current is drawn from VCC. When combined with a CS384X PWM, the Driver Bias switch can be used to supply VIN to the CS3706. VIN switching should be fast as undefined operation of the outputs may occur with VIN less than 5V. Digital Inputs With both an inverting and non-inverting input available, either active-high or active-low signals may be accepted. These are true TTL compatible inputs–the threshold is approximately 1.2V with no hysteresis; and external pullup resistors are not required. Thermal Considerations Should the chip temperature reach approximately 155˚C, a parallel, non-inverting input is activated driving both outputs to the low state. Inhibit Circuit Although it may have other uses, this circuit is included to eliminate the need for deadband control when driving relatively slow bipolar power transistors. A diode from each inhibit input to the opposite power switch collector will keep one output from turning on until the other has turned-off. The threshold is determined by the voltage on INHIBIT REF which can be set from 0.5 to 3.5 V. When this circuit is not used, ground INHIBIT REF and leave INHIBIT A&B open. Truth Table INV. N.I. OUT H L H L H H L L L H L L OUT = INV and N.I. OUT = INV or N.I. 4 CS3706 Application Diagram 14V 10Ω 5V VIN VCC INHIBIT B .047µF 3k VOUTA REF CS3706 2k 100Ω 10k NONINV Input 100Ω INV VOUTB F/F ENABLE .047µF INHIBIT A Gnd 5 10k 100µF RL CS3706 Package Specification PACKAGE THERMAL DATA PACKAGE DIMENSIONS IN mm (INCHES) D Lead Count 16L PDIP (Internally Fused Leads) Metric Max Min 19.69 18.67 16 Lead PDIP Thermal Data RΘJC typ RΘJA typ English Max Min .775 .735 (Internally Fused Leads) 15 50 ˚C/W ˚C/W Plastic DIP (N); 300 mil wide 7.11 (.280) 6.10 (.240) 8.26 (.325) 7.62 (.300) 1.77 (.070) 1.14 (.045) 2.54 (.100) BSC 3.68 (.145) 2.92 (.115) .356 (.014) .203 (.008) 0.39 (.015) MIN. .558 (.022) .356 (.014) REF: JEDEC MS-001 D ON Semiconductor and the ON Logo are trademarks of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor reserves the right to make changes without further notice to any products herein. For additional information and the latest available information, please contact your local ON Semiconductor representative. Ordering Information Part Number CS3706GNF16 Some 8 and 16 lead packages may have 1/2 lead at the end of the package. All specs are the same. Description 16 Lead PDIP (Internally Fused Leads) 6 © Semiconductor Components Industries, LLC, 2000 Notes Notes