LM1951 Solid State 1 Amp Switch General Description Features The LM1951 is a high current, high voltage, high side (PNP) switch with a built-in error detection circuit. The LM1951 is guaranteed to deliver 1 Amp output current and is capable of withstanding up to g 85V transients. The built-in error detection provides an error flag output under the following fault conditions: output short to ground or supply, open load, current limit, overvoltage or thermal shutdown. The LM1951 will drive all types of resistive or inductive loads. The output has a built-in negative voltage clamp ( & b30V) to provide a quick energy discharge path for inductive loads. The LM1951 features TTL and CMOS compatible logic input with hysteresis. Switching times, both turn on and turn off, are 2 ms (Cload k 0.005 mF). In addition, its quiescent current in the OFF state is typically less than 0.1 mA at room temperature and less than 10 mA over the entire operating temperature and voltage range. The LM1951 features make it well suited for industrial and automotive applications. Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 0.1 mA typical quiescent current (OFF state) 1 Amp output current guaranteed g 85V transient protection Reverse voltage protection Negative output voltage clamp Error flag output Internal overvoltage shutdown Internal thermal shutdown Short circuit proof High speed switching (up to 50 kHz) Inductive or resistive loads Low ON resistance (1X maximum) TTL, CMOS compatible input with hysteresis Plastic TO-220 5-lead package ESD protected 4.5V to 26V operation Typical Application Circuit and Connection Diagram TL/H/9133 – 1 VIN Output 0 OFF 1 ON TO-220, 5-Lead TL/H/9133 – 2 Front View Order Number LM1951T See NS Package Number T05A C1995 National Semiconductor Corporation TL/H/9133 RRD-B30M115/Printed in U. S. A. LM1951 Solid State 1 Amp Switch August 1992 Absolute Maximum Ratings Power Dissipation (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Internally Limited Load Inductance 1H Operating Temperature Range (TA) Maximum Junction Temperature Storage Temperature Range Lead Temperature (Soldering, 10 sec.) ESD Tolerance (Note 4): Supply Voltage Operational Voltage 26 VDC b 40 VDC t VCC s 85 VDC Sustained Voltage g 85V Transient Voltage Protection (u e 100 ms, 1% Duty Cycle, RS t 10X) Pins 4, 5 26 VDC b 40§ C to a 125§ C 150§ C b 65§ C to a 150§ C 260§ C 2000V Electrical Characteristics VCC e 12V, Iout e 500 mA, Cout e 0.001 mF, TA e 25§ C unless otherwise specified Parameter Conditions Typical Supply Voltage, VCC Operational Transient u e 100 ms, 1% Duty Cycle, RCC t 10X Tested Limit (Note 2) Design Limit (Note 3) 4.5 Vmin 26 Vmax b 85 V 85 Supply Current Voltage Drop (VCC b VOUT) Short Circuit Current Input Threshold, Pin 5 Units V Iout e 0 mA, VON/OFF e 0.8V 0.1 10 Iout e 250 mA, VON/OFF e 2.0V 260 270 mAmax Iout e 600 mA, VON/OFF e 2.0V 630 650 mAmax Iout e 1A, VON/OFF e 2.0V 1.06 1.2 Amax Iout e 600 mA, VON/OFF e 2.0V 400 600 mVmax Iout e 1A, VON/OFF e 2.0V 0.7 1.0 Vmax VOUT e 0V, VON/OFF e 2V 1.3 4.5V s VCC s 26V Input Current, Pin 5 0.8V s VON/OFF s 5.5V Output Clamp Iout s 600 mA 100 1.0 Amin 2.5 Amax Turn ON 1.4 2.0 2.0 Turn OFF 1.2 0.8 0.8 25 mAmax Vmax Vmin 50 mAmax 10 mAmin b 40 Vmin b 24 Vmax 1 3 msmax 1 3 msmax Rise Time 1 3 msmax Fall Time 1 3 msmax 0.3 0.8 Vmax Delay Time td, ON td, OFF b 30 Rload e 20X, Cload e 0.001 mF Error Flag Characteristics: Output Voltage Error Condition, Pin 4 Low, Sinking 10 mA Sink Current Error Condition, Pin 4 e 0.3V Output Leakage Current No Error, Pin 4 e 26V Response Time VLOGIC e 5V, RLOGIC e 2 kX, CLOGIC e 0 mF 10 3 mAmin 0.01 1 mAmax 1 ms Note 1: Thermal resistance junction-to-case is 3§ C/W. Thermal resistance case-to-ambient is 50§ C/W. Note 2: Tested Limits are guaranteed and 100% production tested. Note 3: Design Limits are guaranteed (but not 100% production tested) over the operating temperature and supply voltage range. These limits are not used to calculate outgoing quality levels. Note 4: Human body model, 100 pF discharged through a 1.5 kX resistor. 2 Typical Performance Characteristics Quiescent Current Quiescent Current Voltage Drop Voltage Drop Short Circuit Current High Voltage Behavior ON/OFF Threshold (Pin 5) ON/OFF Current (Pin 5) ON/OFF Current (Pin 5) Output Voltage Resistive Load Output Voltage Inductive Load TL/H/9133 – 3 3 Error Flag Output Characteristics Open Load Threshold Open Load Threshold Over Voltage Threshold TL/H/9133 – 13 Truth Table Fault Condition VON/OFF* Vout L L H H H H Normal Overvoltage Thermal Shutdown VOUT Short to GND VOUT Short to Vsupply Open Load Current Limit * L j 0 s VON/OFF s 0.8V Error Flag L L L H L L L L L H L L L L H H L L L H L H H L H L L H H L L L H H H L H j 2V s VON/OFF s 26V 4 Typical Applications TL/H/9133 – 4 FIGURE 1. Solenoid Actuated Valve TL/H/9133 – 5 FIGURE 2. 60A 3-Phase Mercury Displacement Relay TL/H/9133 – 6 *Available from Germanium Power Devices, Andover, MA, Tel. (617) 475-5982 FIGURE 3. 25A Switch with Short Circuit Foldback 5 Typical Applications (Continued) TL/H/9133 – 7 FIGURE 4. Latching Switch TL/H/9133 – 8 FIGURE 5. Temperature Controller with Hysteresis TL/H/9133 – 9 FIGURE 6. DC Motor Driver 6 Typical Applications (Continued) TL/H/9133 – 10 FIGURE 7. Over-Voltage Crowbar TL/H/9133 – 11 * Operation Switch Type Empty Normally Open Fill Normally Closed FIGURE 8. Fluid Level Controller TL/H/9133 – 12 FIGURE 9. Indicator Lamp Driver 7 Application Hints may be evident in a combination inductive/capacitive load, or in an inductive load with supply decoupling capacitors in the range of 100 nF to 1 mF. For fast rise and fall times and minimum ringing with inductive loads, a supply decoupling capacitor of 10 nF and an output capacitor of 1 nF is recommended. These should be located as close to the IC pins as possible. The error flag is an open collector output that pulls low under certain fault conditions. These errors include overvoltage (VCC l 26V), overcurrent (IOUT l 1.3A), undercurrent (IOUT k 2 mA), output short circuit to ground, output short circuit to supply, and junction temperature greater than 150§ C. By connecting a 2 kX resistor from the error flag output to a 5V supply a logic output to a microprocessor is provided. The error flag can give seemingly false indications in a number of situations. Slewing large capacitive loads (l100 nF) can drive the LM1951 into temporary current limit, producing a momentary error indication. Incandescent lamps and DC motors require an inrush current that will also cause a temporary current limit and error indication. Large inductive loads (l50 mH) initially appear as open circuits, falsing the error flag. The error flag pulses for about 1 ms when any load is turned ON since the output is initially at ground. In microprocessor systems these false indications are easily ignored in software. In discrete logic circuits utilizing a latch at the error flag output, some filtering may be required. An internal current sink (10 mA minimum) is connected to the input, pin 5. If this pin is left open it is guaranteed to pull low, switching the LM1951 OFF. This characteristic is important under certain fault conditions such as when the control line fails open cirucit. Although the input threshold has hysteresis, the switch points are derived from a very stable band-gap reference. In many applications, such as Figures 5 and 7 , the LM1951 input can replace an extenal reference and comparator. The input (pin 5) is clamped at b0.7V and includes a series resistance of approximately 30 kX. This pin tolerates negative inputs of up to 1 mA without affecting the performance of the chip. When inductive loads are turned OFF, they produce a negative voltage spike. The LM1951 contains a voltage clamp that limits these spikes to approximately b30V, thus an external clamp is not necessary in most applications. Loads with an inductance of greater than 1H, driven to full output current, may damage the clamp simply by exceeding the power capabilities of the LM1951. An LM1951 can dissipate 25W continuous at 25§ C ambient when mounted on a large heatsink. If the load current is limited to 800 mA, the sustained spike from an infinitely large inductance can be handled. Sustained spikes produced by higher currents and high inductances will exceed the 25W limit. For inductances above 1H, care should be taken to see that the output current does not exceed a value that could damage the clamp. While 800 mA is acceptable for the device running at 25§ C ambient on a heatsink, derate this current for smaller heatsinks or higher ambient temperatures to limit the junction temperature to 150§ C. Alternatively, an external clamp or resonating capacitor can be added to handle any combination of load inductance, load current, and device temperature. This is especially important if the output current is boosted, such as the application shown in Figure 3 . A peak power of 750W could be developed in the internal clamp if an inductive load is switched without external clamping. Another case where the clamp’s power capability may be exceeded is when driving a solenoid. The inductance of a solenoid is greatest when energized, with the plunger pulled in. As the plunger is pulled out of the solenoid, the inductance goes down. Under certain conditions of high solenoid inductance and fast mechanical time constants, the current may actually increase when the solenoid is turned OFF. Since the energy stored in an inductor cannot change instantaneously, the current must increase to conserve energy when the inductance decreases. This condition is traced by observing the load current with a current probe and storage oscilloscope. Load capacitances larger than 1 nF will slow rise and fall times. Inductive loads having a capacitive component larger than 1 nF will also exhibit overshoot. Furthermore, ringing 8 9 LM1951 Solid State 1 Amp Switch Physical Dimensions inches (millimeters) Outline Drawing Order Number LM1951T NS Package Number T05A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.