ISL6401 ® Data Sheet PRELIMINARY September 2002 Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) The ISL6401 adjustable frequency, low power, pulse width modulating (PWM) current mode controller is designed for a wide range of DC-DC conversion applications including boost, flyback, and isolated output configurations. The device is optimized to provide a high performance, low-cost solution for Ringing SLIC (RSLIC) ring and talk power supplies. An integrated inverter allows for easy design of negative voltage regulation circuits with a minimal amount of external components. Internal soft start minimizes start-up stress without any external components. Peak current mode control effectively handles Ring trip transients and provides inherent over-current protection. This advanced BiCMOS design features low operating current, adjustable operating output frequency (50kHz to 600kHz), internal soft-start and a SYNC input that allows the oscillator to be locked to an external clock for noise sensitive applications. DC-DC conversion efficiency is optimized by use of a low current sense voltage. A logic level shutdown input is included, which reduces supply current to 55µA in the shutdown mode. Ordering Information PART NUMBER TEMP. RANGE (oC) FN9007.3 Features • Positive and Negative Output Regulation • Starting Supply Current . . . . . . . . . . . . . . . . . 100µA (typ.) • Quiescent Current . . . . . . . . . . . . . . . . . . . . . . 55µA (typ.) • Output Frequency Range. . . . . . . . . . . . 50kHz to 600kHz • External Clock Synchronization • Fast Transient Response with Peak Current Mode Control • Internal Soft-Start • Drives N-Channel MOSFET • Logic Level Shutdown • Leading Edge Blanking • 1% Tolerance Voltage Reference Over Line and Temperature Applications • VoIP/VoDSL Ringer and Off-Hook Voltage Generators • Multi-Output Flyback Supplies • Cable and DSL Modems • Set-Top Boxes PACKAGE PKG. NO. ISL6401CB 0 to 70 14 Ld SOIC M14.15 ISL6401IB -40 to 85 14 Ld SOIC M14.15 ISL6401CR 0 to 70 16 Ld MLFP L16.4x4 ISL6401IR -40 to 85 16 Ld MLFP L16.4x4 • Wireless Local Loops • LMDH and FTTH Supplies • Boost Regulators • Routers Add -T suffix for tape and reel packaging. Pinouts GATE 15 14 13 CT 3 12 GATE SYNC 1 12 PGND COMP 4 11 PGND CT 2 11 PGND COMP 3 10 GND FB 4 9 FB 5 10 GND NFB OUT 6 9 CS NFB IN 7 8 NC 1 5 6 7 8 NC PVCC 16 NC 13 PVCC 1 NFB IN SYNC 2 SD NFB OUT 14 VCC VCC ISL6401 (MLFP) TOP VIEW SD ISL6401 (SOIC) TOP VIEW CS CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved ISL6401 Functional Block Diagram 10 14 GND VREF 4 5 FB COMP ERROR AMP + - + 3 1 SD VCC 200K VOLTAGE REFERENCE IBIAS OSC ILIM S R SOFT START UVLO VREF 9 CS CS GATE 12 Q TFF CLK Q CLK SOFT START 11 R PWRGND ENPWM LVC + SYNC PVCC 13 ICSCOMP POR 2 CT VCC LEADING EDGE BLANKING ICLCOMP + NFB AMP NFB-IN NC 8 7 NFB-OUT 6 Typical Application Schematic for 4 Line VoIP VIN C2 1µF 50V C1A-E 2.2µF 35V 9V TO 20V 8 VCC T1 0 0 0 PRI +5V ±10% 0 0 0 2 SEC 0 7 1 3 C3 1µF 16V GND 0 6 C5 220pF C6 E R1 PVCC 13 3 CT GATE 12 5 FB R3 1.24K GND 10 6 NFB CS 9 7 NULL NC 8 ISL6401 NOTES: 1. C2 fit as close as possible to transformer. 2. T1 = IFLY0012 contacts: Coilcraft: (847) 516-7377 GCI Technology: (972) 423-8411 ext. 245 2 C11 1µF VOUT1 -24V, 120mA VOUT2 -72V, 120mA MUR5120T3 D2 MUR5160T3 IFLY0012 Q1 IRLR2905 4 COMP GNDP 11 0.027µF 20K R2 10K 0 5 VCC 14 2 SYNC D1 C10A 330µF 35V 4 C4 560pF 1 SD GND + R7 220 C8 330pF C9 100µF 100V C12 0.1µF + R6 100 C7 1000pF R5 0.025 1W R4B 143K R4A 43.5K 3. For custom specific designs or questions please contact Intersil at (321) 724-7840. ISL6401 Absolute Maximum Ratings Thermal Information Supply Voltage, VCC,PVCC . . . . . . . . . . . . . . . . GND -0.3V to +7.0V PGND to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.3V Peak GATE Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1A ESD Classification . . . . . . . . . . . . . . . . . . . . . Class 1 (HBM, 2500V) NFB Pin Voltage. . . . . . . . . . . . . . . . . . . . . . ±10V (Transient, 10ms) Thermal Resistance (Typical) Operating Conditions θJA (oC/W) 14 Lead SOIC (Note 4) . . . . . . . . . . . . . . . . . . . . . . 90 16 Lead MLFP (Note 5) . . . . . . . . . . . . . . . . . . . . . . 46 Maximum Junction Temperature (Plastic Package) -55oC to 150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC (SOIC - Lead Tips Only) Temperature Range ISL6401C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC ISL6401I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . 5V ±10% CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 6. All voltages are with respect to GND. Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application schematic. VCC = +5.0V ±10%, TA = 0 to 70oC for ISL6401C and TA = -40 to 85oC for ISL6401I (Note 7), Typical values are at TA = 25oC PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 4.5 5.0 5.5 V VCC SUPPLY Supply Voltage Range Shutdown Supply Current SHDN = GND - 55 100 µA Start-Up Current VCC < 3.7V - 0.1 0.20 mA Operating Supply Current (Note 8) - 3.7 6.0 mA 1.237 1.25 1.262 V - 5 - mV - 1.0 2.0 mA Maximum Input Signal 0.2 0.260 0.3 V Input Bias Current -2.0 0.0 2.0 µA Over Current Threshold 0.4 0.52 0.6 V Open Loop Voltage Gain - 78 - dB Gain-Bandwidth Product 10 - - MHz 1.225 1.25 1.275 V - 1.0 - µA 47 48 50 % - 0 - % REFERENCE VOLTAGE Output Voltage TA = 125oC, 1000 hours Long Term Stability NEGATIVE FEEDBACK Source Current CURRENT SENSE ERROR AMPLIFIER Input Voltage Input Bias Current PWM Maximum Duty Cycle Minimum Duty Cycle COMP = 0V UNDERVOLTAGE LOCKOUT 3 ISL6401 Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to Block Diagram and Typical Application schematic. VCC = +5.0V ±10%, TA = 0 to 70oC for ISL6401C and TA = -40 to 85oC for ISL6401I (Note 7), Typical values are at TA = 25oC (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Start Threshold 3.7 4.1 4.3 V Stop Threshold 3.2 3.6 4.0 V Start to Stop Hysteresis 0.2 0.5 0.8 V - 2048 clk - 90 100 108 kHz 50 - 600 kHz - 5 - % - - 1.2 MHz Sync Input HIGH 3.5 - - V Sync Input LOW - - 1.5 V Minimum Sync. Input Pulse Duty Cycle - 20 - % GATE Low Level - 0.2 0.5 V GATE High VSAT 4.4 4.9 5.5 V SOFT START - DIGITAL COMP Rise Time Rise from 0.5V to REF -1V OSCILLATOR Gate Output Frequency Ct = 560pF Gate Output Frequency Range Temperature Stability Sync. Frequency Range 1.1 Times the natural switching frequency. OUTPUT Rise Time C load = 1500pF - 35 - ns Fall Time C load = 1500pF - 40 - ns NOTE: 7. Specifications at -40oC are guaranteed by design, not production tested. 8. This is the VCC current consumed when the device is active but not switching. Does not include gate drive current. Typical Performance Curves 2.0 120 1.8 1.6 1.4 80 VOLTAGE (V) FREQUENCY (kHz) 100 60 40 1.2 1.0 0.8 0.6 0.4 20 0.2 0 -40 -20 25 60 TEMPERATURE (oC) FIGURE 1. FREQUENCY vs TEMPERATURE 4 85 0 -40 -20 25 60 TEMPERATURE (oC) 85 FIGURE 2. REFERENCE VOLTAGE vs TEMPERATURE ISL6401 Typical Performance Curves (Continued) 5.0 600 4.5 500 4.0 FREQUENCY (kHz) CURRENT (mA) 3.5 3.0 2.5 2.0 1.5 1.0 400 300 200 100 0.5 0 -40 -20 25 60 TEMPERATURE (oC) 85 FIGURE 3. SUPPLY CURRENT vs TEMPERATURE Pin Descriptions SD - This pin is logic level compatible and can be pulled high, tied to VIN or left open for normal operation. Logic low on the SD activates shutdown, reducing the part’s supply current to approximately 55µA. SYNC - This pin is the input pin for external frequency synchronization. The switching frequency of the device can be synchronized by an external clock signal inserted at this pin. The oscillator timing capacitor, CT, is still required, even if an external clock is used. Program the free-running frequency to be a minimum of 10% slower than the SYNC input frequency. CT - This is the oscillator timing pin. The free-running frequency can be set by connecting a timing capacitor to this pin. The oscillator produces a sawtooth waveform with a programmable frequency range of 100kHz to 1.2MHz. Figure 4 may be used as a guideline in selecting the capacitor value required for a given frequency. COMP - COMP is the output of the error amplifier and input of the current comparator. The ISL6401 features built-in full cycle soft start. Soft start is implemented as a clamp on the maximum COMP voltage. FB - Feedback pin that is used for positive output voltage sensing. It is the inverting input of the error amplifier. The non-inverting input of the error amplifier is internally tied to a reference voltage. 0 82 120 180 250 300 390 510 CAPACITANCE (pF) 610 820 1200 FIGURE 4. CAPACITANCE vs FREQUENCY series resistor for negative output voltage regulation applications. CS - This is the input of the current sense comparator. The IC has two different comparators: The PWM comparator and an overcurrent comparator. The over current comparator is only intended for fault sensing, and exceeding the over-current threshold will cause a soft start cycle. GND - GND is a small signal reference ground for all analog functions on this part. PGND - This pin provides a dedicated ground for the output gate driver. The GND and PGND pins should be connected externally using a short printed circuit board trace close to the IC. This is imperative to prevent large, high frequency switching currents flowing through the ground metallization inside the IC. (Decouple PVCC to PGND with a low ESR 0.1µF capacitor.) GATE - This is the device output. It is a high current power driver capable of driving the gate of a power MOSFET with peak currents exceeding 1.0A. This GATE output is actively held low when VCC is below the UVLO threshold (3.7V typ). The high-current power driver consists of FET output devices, which can switch all the way to GND and all the way to VCC. The output stage also provides very low impedance to overshoot and undershoot. NFB-IN - Negative feedback pin that is used for negative output voltage sensing. It is connected to the inverting input of the negative feedback amplifier through a 100K source resistor. PVCC - This pin is for separate collector supply to the output gate drive. Separate PVCC and PGnd helps decouple the IC’s analog circuitry from the high power gate drive noise. Connect this pin to VCC with external short trace on printed circuit board. NFB OUT - This pin is the output of the negative feedback inverter. This pin should be connected the FB pin with a 10k VCC - VCC is the power connection for the device. Although quiescent VCC current is very low, total supply current will be 5 ISL6401 higher, depending on the output current. Total VCC current is the sum of the quiescent VCC current and the average output current. Knowing the operating frequency and the MOSFET gate charge (Qg), average output current can be calculated from: Functional Description the error amplifier output (COMP pin) and the reference input (non-inverting terminal of the error amplifier) to the internally generated soft-start voltage. The oscillator sawtooth waveform is compared to the ramping error amplifier voltage. This generates GATE pulses of increasing width that charge the output capacitor(s). With sufficient output voltage, the clamp on the reference input controls the output voltage. When the internally generated soft-start voltage exceeds the FB pin voltage, the output voltage is in regulation. This method provides a rapid, controlled output voltage rise. Soft-start is implemented during start-up, after an over-current has cleared, or when exiting shutdown or under voltage lock-out (UVLO). Features Gate Drive The ISL6401 current mode, synchronizable PWM, makes an ideal choice for low-cost, low-power, multi-output flyback topology applications with low input-output ripple current requirements. When configured in a multi-winding flyback topology, the IC is capable of generating the negative Talk and Ring voltages required for Ringing Subscriber Line Interface (RSLIC) power supplies. This approach provides dual outputs from a single power switch and control IC. Low current sense voltage and shutdown mode leads to high efficiency operation. Other features include peak current mode control, internal soft-start, adjustable current limit, adjustable frequency and external frequency synchronization. The ISL6401 is capable of sourcing 1A of peak-drive current. Separate collector supply (PVCC) and power ground (PGnd) pins help isolate the IC’s analog circuitry from the high power gate drive noise. To limit the peak current through the IC, an external resistor is placed between the totem-pole output of the IC and the gate of the MOSFET. The minimum value of this resistor is determined by: I OUT = Qg × F To prevent noise problems, bypass VCC to GND with a ceramic capacitor as close to the VCC pin as possible. An electrolytic capacitor may also be used in addition to the ceramic capacitor. Oscillator The ISL6401 has an internal sawtooth oscillator with a programmable frequency range of 100kHz to 1MHz, which can be programmed with a capacitor on the CT pin. (Please refer to Fig. 4 for the capacitance required for a given frequency.) With a maximum 50% duty cycle operation, the output switching frequency is half the oscillator frequency. Implementing Synchronization The oscillator can be synchronized by an external clock inserted at the SYNC pin. Program the free running frequency of the oscillator to be 10% slower than the desired synchronous frequency. The external clock signal should have a minimum pulse width of 20nsec. Soft Start Operation The ISL6401 features an internal digital soft-start with no external capacitor required. Soft-start is used to reduce transformer and output capacitor stress and to reduce the surge on the input circuits, when the converter action starts. The considerable capacitance on the output lines should be charged slowly, so as not to reflect an excessive transient. A very wide initial pulse could result in saturation of the core and voltage overshoot on the output, if the inductor current is allowed to rise to a high value during start up. Upon start-up, the peak primary current increments from 1/5th of the value set by RCS to the full current limit value in steps, over 2048 cycles of Fosc or Fsync. Soft-start clamps 6 Rgate = (Vdd(min) - Vsat) / Igate(peak) This small series resistor also damps any oscillations caused by the resonant tank of the parasitic inductances in the traces of the board and the FET’s input capacitance. A pull-down resistor is sometimes added to the gate drive to insure the MOSFET gate does not get charged to its turn-on threshold during device start-up. Adding a fast-switching diode and smaller value resistor in parallel with the gate resistor helps to control the current the IC needs to sink during turn-off and protects the output stage of the device. These components also help to reduce turn-off losses, which tend to dominate the switching losses in discontinuous current-mode (DCM) converters. Ground Plane Requirements Careful layout is essential for correct operation of the device. A good ground plane must be employed. A unique section of the ground plane must be designated for high di/dt currents associated with the output stage. Power ground (PGND) can be separated from the analog ground (GND) and connected at a single point. VCC should be bypassed directly to PGND with good high frequency capacitors. The return connection for input power to the system and the bulk input capacitor should be connected to the PGND ground plane. Application Information Subscriber Line Interface Circuit Requirements As worldwide demand for inexpensive Voice over Internet Protocol telephony grows, so will the need for ICs that enable compatibility between new telephony systems and older telephones based on analog standards. Old style telephones require signal and power inputs that are not generally available on purely digital systems. Analog ring ISL6401 signal generation and off-hook loop current supply are two analog functions that are performed by Subscriber Line Interface Circuits (SLICs). A SLIC is the primary interface between the 4-wire (ground referenced) low voltage switch environment and the 2 wire (floating) high voltage loop environment. It performs a number of important functions including battery feed, over-voltage protection, ringing, signaling, coding, hybrid balancing and testing. The Ringing SLIC (RSLIC) typically requires two high voltage power supply inputs. The first is a tightly regulated voltage around -24V or -48V for off-hook voice transmission. The second is a loosely regulated -70 to -100V for ring tone generation. When the switch hook is released the phone puts approximately 200Ω of resistance across the phone terminals. Once voice transmission begins, the SLIC requires a lower voltage input to establish a current loop of approximately 25mA. The loop feeds the 200Ω, protection resistors, and line resistances within the phone. ISL6401 Flyback Reference Design The Typical Application Schematic shows a current mode power supply using the Intersil ISL6401 in a standard flyback topology. The IC requires +5V Bias. The application circuit is intended for wall adapters that power home gateway/router boxes. This circuit input voltage can be 9V to 20V with the selected transformer and external components. The output voltages are -24V at 120mA and -72V at 120mA. The circuit uses inexpensive transformers to generate both outputs using a single controller. The transformer turns ratio is such that 24V appear across each secondary winding and the primary during the switch offtime. The remaining secondary windings are stacked in series to develop -48V. The -48V section is then stacked on the -24V section to get the -72V. This technique provides good cross regulation, lowers the voltage rating required for the output capacitors, and lowers the RMS current, allowing the use of less expensive output capacitors. Also, the selection of a transformer with multifilar winding lowers the leakage inductance and cost. The -24V output is precisely regulated by feeding back this output to the controller. The -72V output is derived from the third pair of windings. Regulation of this output is obtained by the turn’s ratio of the transformer with -24V output, as well as with split feedback. Circuit Element Descriptions • Transformers T1, MOSFET Q1, Schottky diode D1, D2, and input capacitor C1and C2 form the power stage of the converter. Power resistor R5 senses the switch current and converts this current into a voltage to be 7 sensed by the primary side controller feedback comparator. • Capacitors C9 to C12 filter out high frequency noise on the output bus directly at the output diode. • R7 and C8 provide secondary side snubbing. • R6 and C7 filter out the leading edge voltage spikes resulting from the leakage inductance of the transformer. • C4 sets the switching frequency of the converter. • C3 is a decoupling capacitor, which should always be a good quality low-ESR / ESL type capacitor, placed as close to the IC pins as possible and returned directly to the IC ground reference. • The gate drive circuitry can be composed of a small gate drive resistor, necessary for damping any oscillations resulting from the input capacitance of Q1 and any parasitic stray inductance. • The voltage sense feedback loop is comprised of R4 and R3. Feedback components R1, C6, and C5 provide the necessary gain and pole to stabilize the control loop. Component Selection Guidelines Power MOSFET The MOSFET switch is selected to meet the drain to source voltage stress resulting from the maximum input voltage (VIN(max)), the reflected secondary voltages, equal to the output voltage (VOUT), plus the output diode voltage drop (VF), and the voltage spike due to the leakage inductance, assumed to be 30% of the input voltage. Vds (stress) = [ (VIN(max)) + (N)(Vout +Vf)] + (0.3)(VIN(max)) The switch must also be able to conduct the repetitive peak primary current as determined by: Ipeak (primary) = (Vinmin - Vds) (tON(max)) / Lp The primary current waveform of a discontinuous mode flyback converter is triangular in shape, therefore, its root mean square(rms) current is calculated by: Irms ( prim ) = ( IPEAKprim ⁄ 3 ) ( ( TONmax ) ⁄ T ) The chosen device should also have a low RDS(ON) value, because the conduction losses of the device are proportional to the square of the primary rms current through the device. Selection of a device that has a peak current rating of at least three times the peak current usually insures acceptably low conduction losses. Pconduction = (Iprms2) (RDS(on)) ISL6401 Switching losses are the result of overlapping drain current and source voltage at turn-off. The drain voltage begins to rise only after the miller capacitance of the device begins to discharge. This discharging time is a function of the external gate resistance, Rgate and the gate-to-drain miller charge Qgd, as shown in the following equation, of right triangle. Therefore, the typical capacitor ripple current rating the output capacitor must meet is equal to, T miller = (Qgd)(RGATE ) / (Vdd-Vth), where Ipeak (sec) is the peak-secondary current and tRESET is equal to the off-time of the switch. The same selection criteria is used for the input capacitor, keeping in mind these capacitors must also be rated to handle the maximum input voltage. where Vth is the turn ON threshold voltage of the gate. The power loss due to the external capacitance of the MOSFET also contributes to the total switching losses, which can be calculated as shown. C oss × V DS ( stress ) 2 P switching = F sw -------------------------------------------------------- + V DS ( stress ) 2 + I peak ( primary ) + t miller During turn on there is no overlap of drain voltage and current because there is no current in a discontinuous current mode converter at turn-on. Minimal losses also occur during the off-time of the FET due to the leakage current. Poff (time) = (1 - Dmax)(Ileak)(Vds(stress)) Output and Input Capacitors Output capacitors are selected based upon their value, equivalent series resistance (ESR), equivalent series inductance and capacitor ripple current rating. The capacitor value controls the peak-to-peak output ripple voltage at the switching frequency. Assuming a linear decay of the capacitor voltage during the off time, during which the capacitor must supply the load current, the minimum value of the output capacitor can be calculated as follows, Cout = [(T- TON(max))(Iout)] / Vripple), where Vripple is the acceptable peak-to peak output voltage ripple. However, there are practical limitations to how low a single stage output filter can reduce the ripple voltage and sometimes an extra LC filter stage is necessary. This second stage filter would also reduce the output high frequency noise. Parasitic resistance and inductance in the output capacitors tend to make the ripple voltage much greater than expected, based upon the above equation. Using capacitors with the lowest possible ESR and ESL helps reduce high frequency ripple. The rms ripple current that the output capacitors experience is not the same as the secondary side rms output current; it is the AC portion of it. The secondary side rms current is in the shape of a clipped sawtooth, or trapezoid, where the output capacitor’s current waveform is in the shape 8 3 ) ( Treset ) 4 – (------------------------------- T Treset Irms = ( Ipeak ) ------------------- ----------------------------------------------- T 12 Output Voltage The output voltage can be set by a feedback resistor divider network. The output is resistively divided and compared to the reference voltage. For negative flyback output applications, the sensed output will be fed to the NFB IN pin. The sensed voltage in inverted, and this positive voltage is fed to the FB- inverting input pin of the error amplifier. The non-inverting input of the error amplifier will be a reference voltage. So, when FB- is higher than REF voltage, the output drivers are turned off. The opposite happens when the resistively divided output voltage falls below the 1.24V reference voltage. Output Diode The output diode in a flyback converter is subject to large peak and rms current stresses. Schottky diodes are recommended, because of their low forward-voltage drop and the virtual absence of minority carrier reverse recovery. The secondary-side Schottky rectifier was selected to meet the working peak-reverse voltage, the peak repetitive forwardcurrent and the average forward-current of the application. The working peak-reverse voltage Vrev, or blocking voltage, is calculated according to the following equation: VR = [(VINmax + VRDSon) / N ]+ VOUT The reflected peak primary current constitutes the peak repetitive forward-current through the diode. Because all current to the output capacitors and load must flow through the diode, the average forward diode current is equal to the steady-state load current. Power loss in the Schottky is the sum of the conduction losses and reverse leakage losses. Conduction losses are calculated using the forward voltage drop across the diode and the average forward-current. Reverse leakage losses are dependent upon the reverse leakage-current, the blocking voltage, and the on-time of the FET. Determining the Turns Ratio of the Flyback Transformer The turns ratio of the flyback transformer can be calculated by using the this steady-state volt-second approach: n = [(VINmin - VDS)(Dmax)(T)] / [(VOUT + VF)(0.8 - Dmax)(T)] ISL6401 Primary Inductance The flyback transformer is actually a coupled inductor, acting as an energy storage unit, as well as performing the usual transformer functions. Crucial considerations include primary inductance, working flux density swing, gap length, the winding scheme and wire diameter. The primary inductance, LP, for a discontinuous mode flyback converter can be calculated according to the following relationship: Lp = n [(VINmin - VDS)(TONmax)]2 / (2)(T)(VOUT)(IOUT) Where n is the assumed efficiency of the converter and Iout is the output current. The ferrite core should have high saturation, low residual flux density, and low losses. An EFD15 core material proved to be suitable for this application. Current Sense The ground referenced sense resistor is selected such that the maximum peak primary current trips the CS pin threshold when this current is 10% higher than its normal operating peak value at the minimum input voltage. This limits the peak primary current in the event of an output short circuit. This resistor must have a power rating to meet the ( I2rms)(R) requirement, where Irms is the root mean square (rms) primary current. Because this resistor defines the maximum peak primary current, the input energy to the transformer is defined and equal to (LP)(I2PEAK) / 2. This defined energy in a fixed frequency discontinuous-mode flyback results in a fixed output power. 9 The advantage of current-mode control is that the output voltage is held constant despite changes in the input voltage, because the peak-primary current remains constant; the slope of this inductor current and its pulse width are adjusted. Leading edge spikes or noise are caused by the reverse recovery of the rectifier, equivalent capacitive loading on the secondary, and parasitic circuit inductances. A small low pass RC filter is added to the current-sense signal to filter out these spikes, so the comparator does not assume an overload condition is present during switch turnon. To avoid excessive phase lag on the current-sense signal, the low pass filter corner frequency is selected to be at least a decade above the switching frequency. ISL6401 Small Outline Plastic Packages (SOIC) M14.15 (JEDEC MS-012-AB ISSUE C) N INDEX AREA 0.25(0.010) M H 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- µα e A1 B 0.25(0.010) M C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3367 0.3444 8.55 8.75 3 E 0.1497 0.1574 3.80 4.00 4 e C 0.10(0.004) B S 0.050 BSC 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 10 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS α 14 0o 14 8o 0o 7 8o Rev. 0 12/93 ISL6401 Micro Lead Frame Plastic Package (MLFP) 2X L16.4x4 0.15 C A D A 16 LEAD MICRO LEAD FRAME PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220-VGGC ISSUE C) D/2 MILLIMETERS D1 D1/2 2X N 6 0.50 DIA. 0.15 C B 1 2 3 E1/2 E/2 E1 0.15 C A NOTES 0.90 - A1 - - 0.05 - A2 - - 0.70 - 0.35 5,8 0.20 REF 0.23 4.00 BSC - 3.75 BSC - E2 0 NX C 1.95 A3 SIDE VIEW A1 2.25 - 3.75 BSC 1.95 2.10 2.25 0.65 BSC k 0.25 L 0.50 - 0.60 - - 0.75 8 2 0.10 M C A B Nd 4 3 8 Ne 4 3 7 NX k D2 2 N P - - 0.60 - θ - - 12 - 4X P Rev. 3 6/01 1 NOTES: 2 3 (Ne-1)Xe REF. E2 E2/2 NX L 1. Dimensioning and tolerancing per ASME Y14.5-1994. 7 2. N is the number of terminals. 8 3. Nd is the number of terminals in the X direction, and Ne is the number of terminals in the Y direction. 4. Controlling dimension: Millimeters. Converted dimensions to inches are not necessarily exact. Angles are in degrees. e (Nd-1)Xe REF. C BOTTOM VIEW C L 7,8 16 D2 8 7,8 N 5 4X P 2.10 4.00 BSC e 0.05 C - D E1 A 0.28 D1 E A2 NX b MAX - D2 2X SEATING PLANE NOMINAL - b B TOP VIEW MIN A A3 E 0.15 C B 2X SYMBOL 5. Dimension b applies to the plated terminal and is measured between 0.20mm and 0.25mm from the terminal tip. C A1 NX b C L 5 6. The Pin #1 identifier exists on the top surface as an indentation mark in the molded body. SECTION "C-C" e e TERMINAL TIP FOR ODD TERMINAL/SIDE 7. Dimensions D2 and E2 are the maximum exposed pad dimensions for improved grounding and thermal performance. 8. Nominal dimensions provided to assist with PCB Land Pattern Design efforts, see Technical Brief TB389. FOR EVEN TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11