19-2805; Rev 0; 4/03 Multichemistry Battery Charger with Automatic System Power Selector Features ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ ±0.5% Accurate Charge Voltage (0°C to +85°C) ±3% Accurate Input Current Limiting ±5% Accurate Charge Current Programmable Charge Current >4A Automatic System Power-Source Selection Analog Inputs Control Charge Current and Charge Voltage Monitor Outputs for Current Drawn from AC Input Source AC Adapter Present Up to 17.65V (max) Battery Voltage Maximum 28V Input Voltage Greater than 95% Efficiency Conditioning Charge Safely Charges Overdischarged Li+ Packs Charges Any Battery Chemistry: Li+, NiCd, NiMH, Lead Acid, etc. Ordering Information PART MAX1909ETI TEMP RANGE PIN-PACKAGE -40°C to +85°C 28 Thin QFN Minimum Operating Circuit Applications P3 Notebook and Subnotebook Computers TO EXTERNAL LOAD 0.01Ω AC ADAPTER: INPUT SRC Hand-Held Data Terminals CSSP Pin Configuration CSSN PDS DHIV SRC PDL P2 27 26 25 23 DHIV SRC 24 DHI CSSN CSSP PDL 28 PDS DCIN TOP VIEW VCTL LDO 22 MAX1909 LDO ICTL MODE DCIN LDO 1 21 2 20 DLOV DLO ACIN 3 19 PGND REF 4 18 CSIP PKPRES 5 17 CSIN ACOK 6 16 BATT MODE 7 15 GND DLOV ACIN VCC IINP IINP REF CLS P1 DHI ACOK MAX1909 TO HOST SYSTEM LDO DLO N1 10µH PGND PKPRES CSIP 9 10 11 12 13 14 IINP CLS ICTL VCTL CCI CCV CCS 0.015Ω 8 THIN QFN CCV CCI CSIN CCS REF BATT GND Functional Diagrams appear at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX1909 General Description The MAX1909 highly integrated control IC simplifies construction of accurate and efficient multichemistry battery chargers. The MAX1909 uses analog inputs to control charge current and voltage, and can be programmed by a host microcontroller (µC) or hardwired. High efficiency is achieved through use of buck topology with synchronous rectification. The maximum current drawn from the AC adapter is programmable to avoid overloading the AC adapter when supplying the load and the battery charger simultaneously. The MAX1909 provides a digital output that indicates the presence of an AC adapter, and an analog output that monitors the current drawn from the AC adapter. Based on the presence or absence of the AC adapter, the MAX1909 automatically selects the appropriate source for supplying power to the system by controlling two external P-channel MOSFETs. Under system control, the MAX1909 allows the battery to undergo a relearning or conditioning cycle in which the battery is completely discharged through the system load and then recharged. The MAX1909 is available in a space-saving 28-pin, 5mm ✕ 5mm thin QFN package and operates over the extended -40°C to +85°C temperature range. MAX1909 Multichemistry Battery Charger with Automatic System Power Selector ABSOLUTE MAXIMUM RATINGS DCIN, CSSP, CSSN, SRC, ACOK to GND..............-0.3V to +30V DHIV ........................................................…SRC + 0.3, SRC - 6V DHI, PDL, PDS to GND ...............................-0.3V to (VSRC + 0.3) BATT, CSIP, CSIN to GND .....................................-0.3V to +20V CSIP to CSIN or CSSP to CSSN or PGND to GND ...-0.3V to +0.3V CCI, CCS, CCV, DLO, IINP, REF, ACIN to GND ........................................-0.3V to (VLDO + 0.3V) DLOV, VCTL, ICTL, MODE, CLS, LDO, PKPRES to GND ...................................................-0.3V to +6V DLOV to LDO.........................................................-0.3V to +0.3V DLO to PGND ..........................................-0.3V to (DLOV + 0.3V) LDO Short-Circuit Current...................................................50mA Continuous Power Dissipation (TA = +70°C) 28-Pin QFN (derate 20.8mW/°C above +70°C) .........1666mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-60°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 0 3.6 V VVCTL = 3.6V (3 or 4 cells); not including VCTL resistor tolerances -0.8 +0.8 VVCTL = 3.6V/20 (3 or 4 cells); not including VCTL resistor tolerances -0.8 +0.8 CHARGE VOLTAGE REGULATION VCTL Range Battery Regulation Voltage Accuracy VVCTL Default Threshold VCTL Input Bias Current % VVCTL = 3.6V (3 or 4 cells); including VCTL resistor tolerances of 1% -1.0 +1.0 VVCTL = VLDO (3 or 4 cells, default threshold of 4.2V/cell) -0.5 +0.5 VVCTL rising 4.1 4.3 VVCTL = 3V 0 2.5 VDCIN = 0, VVCTL = 5V 0 12 0 3.6 V 80.63 mV V µA CHARGE-CURRENT REGULATION ICTL Range CSIP-to-CSIN Full-Scale CurrentSense Voltage 69.37 VICTL = 3.6V (not including ICTL resistor tolerances) -7.5 +7.5 -5 +5 VICTL = 0.9V (not including ICTL resistor tolerances) -7.5 +7.5 VICTL = 3.6V x 0.5 (including ICTL resistor tolerances of 1%) -7.0 +7.0 VICTL = 3.6V x 0.5 (not including ICTL resistor tolerances) Charge-Current Accuracy VICTL Default Threshold 2 75.00 VICTL = VLDO (default threshold of 45mV) -5 VICTL rising 4.1 % +5 4.2 _______________________________________________________________________________________ 4.3 V Multichemistry Battery Charger with Automatic System Power Selector (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS BATT/CSIP/CSIN Input Voltage Range MIN TYP 0 CSIP/CSIN Input Current MAX UNITS 19 V Charging enabled 350 650 Charging disabled; VDCIN = 0 or VICTL = 0 0.1 1 ICTL Power-Down Mode Threshold Voltage 0.75 ICTL Power-Up Mode Threshold Voltage 0.85 ICTL Input Bias Current µA V V VICTL = 3V -1 +1 VDCIN = 0V, VICTL = 5V -1 +1 µA INPUT CURRENT REGULATION CSSP-to-CSSN Full-Scale Current-Sense Voltage 72.75 Input Current-Limit Accuracy 77.25 VCLS = REF -3 +3 VCLS = REF x 0.75 -3 +3 VCLS = REF x 0.5 -4 +4 8.0 28 CSSP/CSSN Input Voltage Range CSSP/CSSN Input Current 75.00 VCSSP = VCSSN = VDCIN > 8.0V 450 730 VDCIN = 0 0.1 1 CLS Input Range mV % V µA 1.6 REF V CLS Input Bias Current VCLS = 2.0V -1 +1 µA IINP Transconductance VCSSP - VCSSN = 56mV 2.7 3.3 mA/V VCSSP - VCSSN = 75mV, terminated with 10kΩ -7.5 +7.5 VCSSP - VCSSN = 56mV, terminated with 10kΩ -5 +5 VCSSP - VCSSN = 20mV, terminated with 10kΩ -10 +10 IINP Output Current VCSSP - VCSSN = 150mV, VIINP = 0V 350 µA IINP Output Voltage VCSSP - VCSSN = 150mV, VIINP = float 3.5 V IINP Accuracy 3.0 % SUPPLY AND LINEAR REGULATOR DCIN Input Voltage Range VDCIN 8.0 DCIN falling DCIN Undervoltage Lockout Trip Point DCIN Quiescent Current IDCIN 7 28 7.4 DCIN rising 7.5 7.85 8.0V < VDCIN < 28V 2.7 6 V V mA _______________________________________________________________________________________ 3 MAX1909 ELECTRICAL CHARACTERISTICS (continued) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector ELECTRICAL CHARACTERISTICS (continued) (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER BATT Input Current SYMBOL IBATT CONDITIONS MIN TYP MAX 0.1 1 0.1 1 200 500 5.4 5.55 V 80 115 mV 3.20 4 5.15 V 4.2023 4.2235 4.2447 V 3.1 3.9 V 50 100 150 mV 100 200 300 mV 2.007 2.048 2.089 V 10 20 VBATT = 19V, VDCIN = 0V, or ICTL = 0V VBATT = 16.8V, VDCIN = 19V, ICTL = 0V VBATT = 2V to 19V, VDCIN > VBATT + 0.3V LDO Output Voltage 8.0V < VDCIN < 28V, no load LDO Load Regulation 0 < ILDO < 10mA LDO Undervoltage Lockout Trip Point VDCIN = 8.0V 5.25 UNITS µA REFERENCE REF Output Voltage Ref REF Undervoltage Lockout Trip Point 0 < IREF < 500µA REF falling TRIP POINTS BATT POWER_FAIL Threshold VDCIN - VBATT, VDCIN falling BATT POWER_FAIL Threshold Hysteresis ACIN Threshold ACIN rising ACIN Threshold Hysteresis ACIN Input Bias Current VACIN = 2.048V -1 30 mV +1 µA ns SWITCHING REGULATOR DHI Off-Time VBATT = 16.0V, VDCIN = 19V, VMODE = 3.6V 360 400 440 DHI Minimum Off-Time VBATT = 16.0V, VDCIN = 17V, VMODE = 3.6V 260 300 350 ns 5 10 µA DLOV Supply Current IDLOV DLO low Sense Voltage for Minimum Discontinuous Mode Ripple Current 7.5 mV Cycle-by-Cycle Current-Limit Sense Voltage 97 mV Sense Voltage for Battery Undervoltage Charge Current Battery Undervoltage Threshold DHIV Output Voltage BATT = 3.0V per cell MODE = float (3 cell), V BATT rising MODE = DLOV (4 cell), B VATT rising With respect to SRC DHIV Sink Current 3 4.5 6 9.18 9.42 12.235 12.565 -4.5 -5.0 -5.5 10 mV V V mA DHI On-Resistance Low DHI = VDHIV, IDHI = -10mA 2 5 Ω DHI On-Resistance High DHI = VCSSN, IDHI = 10mA 2 4 Ω DLO On-Resistance High VDLOV = 4.5V, IDLO = +100mA 3 7 Ω DLO On-Resistance Low VDLOV = 4.5V, IDLO = -100mA 1 3 Ω 4 _______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX VCTL = 3.6, VBATT = 16.8V, MODE = LDO 0.0625 0.125 0.2500 VCTL = 3.6, VBATT = 12.6V, MODE = FLOAT 0.0833 0.167 0.3330 UNITS ERROR AMPLIFIERS GMV Loop Transconductance mA/V GMI Loop Transconductance ICTL = 3.6V, VCSSP - VCSIN = 75mV 0.5 1 2 mA/V GMS Loop Transconductance VCLS = 2.048V, VCSSP - VCSSN = 75mV 0.5 1 2 mA/V CCI/CCS/CCV Clamp Voltage 0.25V < VCCV < 2.0V, 0.25V < VCCI < 2.0V, 0.25V < VCCS < 2.0V 150 300 600 mV 0.8 V 2.0 V -2 +2 µA 0 28 LOGIC LEVELS MODE Input Low Voltage MODE Input Middle Voltage 1.6 MODE Input High Voltage 2.8 MODE Input Bias Current MODE = 0V or 3.6V 1.8 V ACOK AND PKPRES ACOK Input Voltage Range ACOK Sink Current VACOK = 0.4V, ACIN = 1.5V ACOK Leakage Current VACOK = 28V, ACIN = 2.5V PKPRES Input Voltage Range PKPRES Input Bias Current PKPRES Battery Removal Detect Threshold PKPRES rising 1 V mA 1 µA 0 LDO V -1 +1 90 PKPRES Hysteresis µA % of LDO 1 % PDS, PDL SWITCH CONTROL PDS Switch Turn-Off Threshold VDCIN - VBATT, VDCIN falling 50 100 150 mV PDS Switch Threshold Hysteresis VDCIN - VBATT 100 200 300 mV PDS Output Low Voltage, PDS Below SRC IPDS = 0V 8 10 12 V PDS Turn-On Current PDS = SRC 6 12 PDS Turn-Off Current VPDS = VSRC - 2V, VDCIN = 16V 10 50 PDL Switch Turn-On Threshold VDCIN - VBATT, VDCIN falling 50 100 150 mV PDL Switch Threshold Hysteresis VDCIN - VBATT 100 200 300 mV PDL Turn-On Resistance PDL = GND 50 100 150 PDL Turn-Off Current VSRC - VPDL = 1.5V 6 12 SRC Input Bias Current Delay Time Between PDL and PDS Transitions SRC = 19V, DCIN = 0V mA mA 1 SRC = 19, VBATT = 16V 2.5 kΩ mA 450 1000 5 7.5 µA µs _______________________________________________________________________________________ 5 MAX1909 ELECTRICAL CHARACTERISTICS (continued) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector ELECTRICAL CHARACTERISTICS (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS V CHARGE VOLTAGE REGULATION VCTL Range Battery Regulation Voltage Accuracy VVCTL Default Threshold VCTL Input Bias Current 0 3.6 VVCTL = 3.6V (3 or 4 cells); not including VCTL resistor tolerances -0.8 +0.8 VVCTL = 3.6V/20 (3 or 4 cells); not including VCTL resistor tolerances -0.8 +0.8 VVCTL = 3.6V (3 or 4 cells); including VCTL resistor tolerances of 1% -1.0 +1.0 VVCTL = VLDO (3 or 4 cells, default threshold of 4.2V/cell) -0.8 +0.8 VVCTL rising 4.1 4.3 VVCTL = 3V 0 2.5 VDCIN = 0V, VVCTL = 5V 0 12 0 3.6 V 69.37 80.63 mV -7.5 +7.5 -5 +5 VICTL = 0.9V (not including ICTL resistor tolerances) -7.5 +7.5 VICTL = 3.6V x 0.5 (including ICTL resistor tolerances of 1%) -7.0 +7.0 VICTL = VLDO (default threshold of 45mV) -5 +5 VICTL rising 4.3 % V µA CHARGE-CURRENT REGULATION ICTL Range CSIP-to-CSIN Full-Scale CurrentSense Voltage VICTL = 3.6V (not including ICTL resistor tolerances) VICTL = 3.6V x 0.5 (not including ICTL resistor tolerances) Charge-Current Accuracy VICTL Default Threshold BATT/CSIP/CSIN Input Voltage Range CSIP/CSIN Input Current 0 Charging enabled ICTL Power-Down Mode Threshold Voltage ICTL Power-Up Mode Threshold Voltage % V 19 V 650 µA 0.75 V 0.85 V INPUT CURRENT REGULATION CSSP-to-CSSN Full-Scale Current-Sense Voltage 6 72.75 _______________________________________________________________________________________ 77.25 mV Multichemistry Battery Charger with Automatic System Power Selector (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS VCLS = REF -3 +3 VCLS = REF x 0.75 -3 +3 VCLS = REF x 0.5 -4 +4 8.0 28 V 730 µA 1.6 REF V VCSSP - VCSSN = 56mV 2.7 3.3 mA/V VCSSP - VCSSN = 75mV, terminated with 10kΩ -7.5 +7.5 VCSSP - VCSSN = 56mV, terminated with 10kΩ -5 +5 VCSSP - VCSSN = 20mV, terminated with 10kΩ -10 +10 IINP Output Current VCSSP - VCSSN = 150mV, VIINP = 0V 350 µA IINP Output Voltage VCSSP - VCSSN = 150mV, VIINP = float 3.5 V Input Current-Limit Accuracy CSSP/CSSN Input Voltage Range CSSP/CSSN Input Current VCSSP = VCSSN = VDCIN > 8.0V CLS Input Range IINP Transconductance IINP Accuracy % % SUPPLY AND LINEAR REGULATOR DCIN Input Voltage Range VDCIN 8.0 DCIN falling DCIN Undervoltage Lockout Trip Point DCIN rising DCIN Quiescent Current IDCIN 8.0V < VDCIN < 28V BATT Input Current IBATT VBATT = 2V to 19V, VDCIN > VBATT + 0.3V LDO Output Voltage 8.0V < VDCIN < 28V, no load LDO Load Regulation 0 < ILDO < 10mA LDO Undervoltage Lockout Trip Point VDCIN = 8.0V 28 7 7.85 V V 6 mA 500 µA 5.55 V 115 mV 3.2 5.15 V 4.1960 4.2520 V 3.9 V 50 150 mV 100 300 mV 2.007 2.089 V 10 30 mV 5.25 REFERENCE REF Output Voltage Ref REF Undervoltage Lockout Trip Point 0 < IREF < 500µA REF falling TRIP POINTS BATT POWER_FAIL Threshold VDCIN - VBATT, VDCIN falling BATT POWER_FAIL Threshold Hysteresis ACIN Threshold ACIN rising ACIN Threshold Hysteresis _______________________________________________________________________________________ 7 MAX1909 ELECTRICAL CHARACTERISTICS (continued) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector ELECTRICAL CHARACTERISTICS (continued) (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN DHI Off-Time VBATT = 16.0V, VDCIN = 19V, VMODE = 3.6V DHI Minimum Off-Time VBATT = 16.0V, VDCIN = 17V, VMODE = 3.6V TYP MAX UNITS 360 440 ns 260 350 ns 10 µA 3 6 mV 9.18 9.42 12.235 12.565 -4.5 -5.5 SWITCHING REGULATOR DLOV Supply Current Sense Voltage for Battery Undervoltage Charge Current IDLOV DLO low BATT = 3.0V per cell Battery Undervoltage Threshold MODE = float (3 cell), VBATT rising DHIV Output Voltage With respect to SRC MODE = DLOV (4 cell), VBATT rising DHIV Sink Current 10 V V mA DHI On-Resistance Low DHI = VDHIV, IDHI = -10mA 5 Ω DHI On-Resistance High DHI = VCSSN, IDHI = 10mA 4 Ω DLO On-Resistance High VDLOV = 4.5V, IDLO = +100mA 7 Ω DLO On-Resistance Low VDLOV = 4.5V, IDLO = -100mA 3 Ω ERROR AMPLIFIERS GMV Loop Transconductance VCTL = 3.6, VBATT = 16.8V, MODE = LDO 0.0625 0.2500 VCTL = 3.6, VBATT = 12.6V, MODE = FLOAT 0.0833 0.3330 mA/V GMI Loop Transconductance ICTL = 3.6V, VCSSP - VCSIN = 75mV 0.5 2 mA/V GMS Loop Transconductance VCLS = 2.048V, VCSSP - VCSSN = 75mV 0.5 2 mA/V CCI/CCS/CCV Clamp Voltage 0.25V < VCCV < 2.0V, 0.25V < VCCI < 2.0V, 0.25V < VCCS < 2.0V 150 600 mV 0.8 V 2.0 V LOGIC LEVELS MODE Input Low Voltage MODE Input Middle Voltage 1.6 MODE Input High Voltage 2.8 V ACOK AND PKPRES ACOK Input Voltage Range ACOK Sink Current 0 VACOK = 0.4V, ACIN = 1.5V PKPRES Input Voltage Range PKPRES Battery Removal Detect Threshold 28 1 0 PKPRES rising 90 VDCIN - VBATT, VDCIN falling 50 V mA LDO V % of LDO PDS, PDL SWITCH CONTROL PDS Switch Turn-Off Threshold 8 _______________________________________________________________________________________ 150 mV Multichemistry Battery Charger with Automatic System Power Selector (Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VBATT = VCSIP = VCSIN = 12V, VVCTL = VICTL = 1.8V, MODE = float, ACIN = 0, CLS = REF, GND = PGND = 0, PKPRES = GND, LDO = DLOV, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 100 300 mV 8 12 V PDS Switch Threshold Hysteresis VDCIN - VBATT PDS Output Low Voltage, PDS Below SRC IPDS = 0V PDS Turn-On Current PDS = SRC 6 PDS Turn-Off Current VPDS = VSRC - 2V, VDCIN = 16V 10 PDL Switch Turn-On Threshold VDCIN - VBATT, VDCIN falling 50 150 mV PDL Switch Threshold Hysteresis VDCIN - VBATT 100 300 mV PDL Turn-On Resistance PDL = GND 50 150 kΩ PDL Turn-Off Current VSRC - VPDL = 1.5V 6 SRC Input Bias Current SRC = 19, VBATT = 16V Delay Time Between PDL and PDS Transitions mA mA mA 2.5 1000 µA 7.5 µs Note 1: Guaranteed by design. Not production tested. Typical Operating Characteristics (Circuit of Figure 2, VDCIN = 20V, charge current = 3A, 4 Li+ series cells, TA = +25°C, unless otherwise noted.) BATTERY INSERTION AND REMOVAL RESPONSE SYSTEM LOAD TRANSIENT RESPONSE MAX1909 toc01 MAX1909 toc02 17V 5A ISYSTEMLOAD 0A VBATT 16V VCCV 0A 5A 5A/div IBATT IIN 0A 5A IBATT 0A IIN 0A 5A/div VCCV VCCI VCCI VCCV CCS 3V 3V 2V VCCI, VCCV 1V CCI VCCI 0V 500µs/div 2V VCCI 1V VCCS 0V 100µs/div _______________________________________________________________________________________ 9 MAX1909 ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (continued) (Circuit of Figure 2, VDCIN = 20V, charge current = 3A, 4 Li+ series cells, TA = +25°C, unless otherwise noted.) LDO LOAD REGULATION LINE TRANSIENT RESPONSE 0 30V VDCIN 20V MAX1909 toc04 MAX1909 toc03 -0.2 LDO OUTPUT ERROR (%) INDUCTOR CURRENT 200mA/div 3A VBATT AC-COUPLED 200mV/div -0.4 -0.6 -0.8 -1.0 -1.2 1.8V VCCV 1.6V -1.4 0 500µs/div 1 2 3 4 5 6 7 8 9 10 LDO CURRENT (mA) REF LOAD REGULATION -0.04 -0.06 -0.08 -0.10 -0.14 0 10 30 20 200 EFFICIENCY vs. CHARGE CURRENT 600 800 1000 90 88 86 84 82 MAX1909 toc09 450 400 1.5 2.0 CHARGE CURRENT (A) 2.5 3.0 60 3.5 CHARGER DISABLED 3.0 350 300 250 200 85 2.5 2.0 1.5 150 1.0 100 0.5 0 0 1.0 35 IINP ERROR vs. INPUT CURRENT 50 80 10 4.0 IINP (%) 3 CELLS 0.5 -15 TEMPERATURE (°C) 500 SWITCHING FREQUENCY (kHz) 94 0 -40 SWITCHING FREQUENCY vs. VIN - VBATT MAX1909 toc08 4 CELLS 96 10 400 REF CURRENT (µA) 100 92 -0.10 -0.20 0 INPUT VOLTAGE (V) 98 -0.05 -0.15 -0.12 -0.10 0 MAX1909 toc10 -0.05 0.05 REF OUTPUT ERROR (%) 0 0.10 MAX1909 toc06 MAX1909 toc05 -0.02 REF OUTPUT ERROR (%) LDO OUTPUT ERROR (%) 0.05 REF vs. TEMPERATURE 0 MAX1909 toc07 LDO LINE REGULATION 0.10 EFFICIENCY (%) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector 0 2 4 6 VIN - VBATT (V) 8 10 0 0.5 1.0 1.5 2.0 2.5 INPUT CURRENT (A) ______________________________________________________________________________________ 3.0 3.5 Multichemistry Battery Charger with Automatic System Power Selector INPUT CURRENT-LIMIT ACCURACY vs. SYSTEM LOAD 4 2 0 -2 -4 -6 -8 VBATT = 10V 2 1 VBATT = 16V VBATT = 12V 0 ICHARGE = 3A -1 2 1 0 -1 -2 -3 -2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 MAX1909 toc13 VBATT = 13V 3 INPUT CURRENT-LIMIT ACCURACY vs. VCLS 3 INPUT CURRENT-LIMIT ACCURACY (%) IINP ACCURACY (%) 6 4 INPUT CURRENT-LIMIT ACCURACY (%) MAX1909 toc11 8 MAX1909 toc12 IINP ACCURACY vs. INPUT CURRENT 0.5 1.0 INPUT CURRENT (A) 1.5 2.0 2.5 3.0 1.5 2.0 2.5 PDL-PDS SWITCHING, AC ADAPTER INSERTION 3.5 PDS-PDL SWITCHOVER, WALL ADAPTER REMOVAL MAX1909 toc14 MAX1909 toc15 20V VPDS 3.0 VCLS (V) SYSTEM LOAD (A) VWALLADAPTER 10V 20V 20V VSYSTEMLOAD 10V VPDS 20V VWALLADAPTER 10V VSYSTEMLOAD, VPDS 10V SYSTEM LOAD VPDL 0V VPDS 20V VPDL 20V VBATT 10V VPDL 0V VPDL, VBATT 10V 0V VPDL VSYSTEMLOAD 100µs/div 500µs/div PDS-PDL SWITCHOVER, BATTERY INSERTION PDL-PDS SWITCHING, BATTERY REMOVAL MAX1909 toc16 20V VPDS 15V VSYSTEM CONDITIONING MODE 10V WALL ADAPTER = 18V 5V VPKDET 0V VPKPRES 15V VBATT 10V MAX1909 toc17 20V VSYSTEM CONDITIONING MODE 15V WALL ADAPTER = 18V 10V VPDS 5V VPKPRES 0V VPDL 15V VBATT 10V 5V V PDL 5V 0V 50µs/div 0V 10µs/div ______________________________________________________________________________________ 11 MAX1909 Typical Operating Characteristics (continued) (Circuit of Figure 2, VDCIN = 20V, charge current = 3A, 4 Li+ series cells, TA = +25°C, unless otherwise noted.) Multichemistry Battery Charger with Automatic System Power Selector MAX1909 Pin Description 12 PIN NAME FUNCTION 1 DCIN DC Supply Voltage Input. Bypass DCIN with a 1µF capacitor to power ground. 2 LDO Device Power Supply. Output of the 5.4V linear regulator supplied from DCIN. Bypass with a 1µF capacitor. 3 ACIN AC Detect Input. This uncommitted comparator input can be used to detect the presence of the charger’s power source. The comparator’s open-drain output is the ACOK signal. 4 REF 4.2235V Voltage Reference. Bypass with a 1µF capacitor to GND. 5 PKPRES 6 ACOK AC Detect Output. High-voltage open-drain output is high impedance when ACIN is greater than 2.048V. The ACOK output remains a high impedance when the MAX1909 is powered down. 7 MODE Trilevel Input for Setting Number of Cells and Asserting the Conditioning Mode: MODE = GND; asserts conditioning mode. MODE = float; charge with 3 times the cell voltage programmed at VCTL. MODE = LDO; charge with 4 times the cell voltage programmed at VCTL. 8 IINP Input Current Monitor Output. The current delivered at the IINP output is a scaled-down replica of the system load current plus the input-referred charge current sensed across CSSP and CSSN inputs. The transconductance of (CSSP - CSSN) to IINP is 3mA/V. Pull PKPRES high to disable charging. Used for detecting presence of battery pack. This input can also be used as a simple shutdown control. 9 CLS Source Current-Limit Input. Voltage input for setting the current limit of the input source. 10 ICTL Input for Setting Maximum Output Current 11 VCTL Input for Setting Maximum Output Voltage 12 CCI Output Current Regulation Loop Compensation Point. Connect 0.01µF to GND. 13 CCV Voltage Regulation Loop Compensation Point. Connect 20kΩ in series with 0.01µF to GND. 14 CCS Input Current Regulation Loop Compensation Point. Use 470pF to GND. 15 GND Analog Ground 16 BATT Battery Voltage Feedback Input 17 CSIN Output Current-Sense Negative Input 18 CSIP Output Current-Sense Positive Input. Connect a current-sense resistor from CSIP to CSIN. 19 PGND 20 DLO 21 DLOV Low-Side Driver Supply. Bypass with a 0.1µF capacitor to ground. 22 DHIV High-Side Driver Supply. Bypass with a 0.1µF capacitor to SRC. 23 DHI High-Side Power MOSFET Driver Output. Connect to high-side PMOS gate. When the MAX1909 is shut down, the DHI output is HIGH. 24 SRC Source Connection for Driver for PDS/PDL Switches. Bypass SRC to power ground with a 1µF capacitor. 25 CSSN Input Current Sense for Charger (Negative Input). 26 CSSP Input Current Sense for Charger (Positive Input). Connect a current-sense resistor from CSSP to CSSN. 27 PDS Power Source PMOS Switch Driver Output. When the MAX1909 is powered down, the PDS output is pulled to SRC through an internal 1MΩ resistor. 28 PDL System Load PMOS Switch Driver Output. When the MAX1909 is powered down, the PDL output is pulled to ground through an internal 100kΩ resistor. Power Ground Low-Side Power MOSFET Driver Output. Connect to low-side NMOS gate. When the MAX1909 is shut down, the DLO output is LOW. ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector RS1 0.01Ω MAX1909 P3 AC ADAPTER TO SYSTEM LOAD C1 22µF SRC OUTPUT VOLTAGE: 12.6V C22 1µF CHARGE I LIMIT: 3.0A CSSP D4 R6 590kΩ 1% CSSN PDS C17 0.1µF SRC R7 196kΩ 1% DCIN C5 1µF MAX1909 PDL LDO VCTL R4 100kΩ LDO DHIV ICTL OUTPUT DLOV ACIN P2 C13 1µF R13 33Ω C16 1µF MODE VCC P1 (INPUT I LIMIT: 7.5A) R8 1MΩ REF DHI CLS ACOK DLO TO HOST SYSTEM LDO N1 L1 10µH PGND R9 10kΩ CSIP RS2 0.015Ω PKPRES CCV CCI R5 10kΩ C11 0.1µF CCS C9 0.01µF CSIN BATT GND REF C10 0.01µF BATT + C4 22µF C12 1µF BATTERY TEMP GND BATT PGND GND Figure 1. Typical Operating Circuit Demonstrating Hardwired Control ______________________________________________________________________________________ 13 MAX1909 Multichemistry Battery Charger with Automatic System Power Selector P3 P4 RS1 0.01Ω AC ADAPTER TO SYSTEM LOAD C1 22µF SRC OUTPUT VOLTAGE: 16.8V D5 C15 1µF D4 R6 590kΩ 1% CSSP CSSN PDS C17 0.1µF SRC R7 196kΩ 1% DHIV DCIN C5 1µF MAX1909 LDO D/A OUTPUT PDL LDO VCTL P2 C13 1µF ICTL OPEN-DRAIN DLOV OUTPUTS MODE ACIN VCC C16 1µF P1 R8 1MΩ DHI ACOK INPUT OUTPUT PKPRES A/D INPUT C14 0.1µF R9 10kΩ (INPUT I LIMIT: 7.5A) REF DLO CSIP R19, R20 10kΩ RS2 0.015Ω C11 0.1µF LDO CSIN BATT CCI R21 10kΩ CCS C9 0.01µF L1 10µH PGND CLS CCV HOST N1 IINP R5 10kΩ AVDD/REF R13 33Ω C10 0.01µF GND REF BATT + C4 22µF SMART BATTERY C12 1µF SCL SCL SDA SDA TEMP GND BATT PGND GND Figure 2. Smart-Battery Charger Circuit Demonstrating Operation with a Host Microcontroller 14 ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector MAX1909 DCIN PKPRES LDO PACK_ON RDY 5.4V LINEAR REGULATOR 0.9 * LDO 4.2235V REFERENCE ICTLOK GND ACIN ACOK CHG LOGIC 0.8V REF BATT 2.048V SRDY DRIVER DCIN GND SRC PDS CHG CCS SRC-10V DRIVER PDL CLS MODE 100kΩ GMS CSSP SWITCH LOGIC LEVEL SHIFTER CSSN CSIP LEVEL SHIFTER CSIN Gm IINP SRC GMI DRIVER ICTL DHI CCI DHIV BATT LVC BATT_UV 3.1V/CELL MODE CELL SELECT LOGIC AND BATTERY VOLTAGEDIVIDER DC-TO-DC CONVERTER GMV CCV DLOV REF DRIVER R DLO 9R VCTL MAX1909 PGND R Figure 3. Functional Diagram ______________________________________________________________________________________ 15 MAX1909 Multichemistry Battery Charger with Automatic System Power Selector Detailed Description The MAX1909 includes all of the functions necessary to charge Li+, NiMH, and NiCd batteries. A high-efficiency synchronous-rectified step-down DC-to-DC converter is used to implement a precision constant-current, constant-voltage charger with input current limiting. The DC-to-DC converter uses external P-channel/N-channel MOSFETs as the buck switch and synchronous rectifier to convert the input voltage to the required charge current and voltage. The charge current and input currentlimit sense amplifiers have low-input-referred offset errors and can use small-value sense resistors. The MAX1909 features a voltage-regulation loop (CCV) and two current-regulation loops (CCI and CCS). The CCV voltage-regulation loop monitors BATT to ensure that its voltage never exceeds the voltage set by VCTL. The CCI battery current-regulation loop monitors current delivered to BATT to ensure that it never exceeds the current limit set by ICTL. A third loop (CCS) takes control and reduces the charge current when the sum of the system load and the input-referred charge current exceeds the power source current limit set by CLS. Tying CLS to the reference voltage provides a 7.5A input current limit with a 10mΩ sense resistor. The ICTL, VCTL, and CLS analog inputs set the charge current, charge voltage, and input current limit, respectively. For standard applications, internal set points for ICTL and VCTL provide a 3A charge current using a 15mΩ sense resistor and a 4.2V per-cell charge voltage. The variable for controlling the number of cells is set with the MODE input. The PKPRES input is used for battery-pack detection, and provides shutdown control from a logic signal or external thermistor. Based on the presence or absence of the AC adapter, the MAX1909 automatically provides an open-drain logic output signal ACOK and selects the appropriate source for supplying power to the system. A P-channel load switch controlled from the PDL output and a similar Pchannel source switch controlled from the PDS output are used to implement this function. Using the MODE control input, the MAX1909 can be programmed to perform a relearning, or conditioning, cycle in which the battery is isolated from the charger and completely discharged through the system load. When the battery reaches 100% depth of discharge, it is recharged to full capacity. The circuit shown in Figure 1 demonstrates a simple hardwired application, while Figure 2 shows a typical application for smart-battery systems with variable charge current and source switch configuration that supports battery conditioning. Smart-battery systems typically use a host µC to achieve this added functionality. 16 Setting the Charge Voltage The MAX1909 uses a high-accuracy voltage regulator for charge voltage. The VCTL input adjusts the battery output voltage. In default mode (VCTL = LDO), the overall accuracy of the charge voltage is ±0.5%. VCTL is allowed to vary from 0 to 3.6V, which provides a 10% adjustment range of the battery voltage. Limiting the adjustment range reduces the sensitivity of the charge voltage to external resistor tolerances from ±2% to ±0.2%. The overall accuracy of the charge voltage is better than ±1% when using ±1% resistors to divide down the reference to establish VCTL. The per-cell battery termination voltage is a function of the battery chemistry and construction. Consult the battery manufacturer to determine this voltage. The battery voltage is calculated by the equation: − 1.8V V VBATT = CELL VREF + VCTL 9.52 where VREF = 4.2235V, and CELL is the number of cells selected with the MAX1909’s trilevel MODE control input. When MODE is tied to the LDO output, CELL = 4. When MODE is left floating, CELL = 3. When MODE is tied to ground, the charger enters conditioning mode, which is used to isolate the battery from the charger and discharge it through the system load. See the Conditioning Mode section. The internal error amplifier (GMV) maintains voltage regulation (See Figure 3 for Functional Diagram). The voltage-error amplifier is compensated at CCV. The component values shown in Figures 1 and 2 provide suitable performance for most applications. Individual compensation of the voltage regulation and current-regulation loops allow for optimal compensation. See the Compensation section. Setting the Charge Current The voltage on the ICTL input sets the maximum voltage across current-sense resistor RS2, which in turn determines the charge current. The full-scale differential voltage between CSIP and CSIN is 75mV; thus, for a 0.015Ω sense resistor, the maximum charge current is 5A. In default mode (ICTL = LDO), the sense voltage is 45mV with an overall accuracy of ±5%. The charge current is programmed with ICTL using the equation: ICHG = 0.075 VICTL × RS2 3.6V The input range for ICTL is 0.9V to 3.6V. The charger shuts down if ICTL is forced below 0.8V (typ). When choosing current-sense resistor RS2, note that it must have a sufficient power rating to handle the full-load ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector Setting the Input Current Limit The total input current, from a wall cube or other DC source, is the sum of the system supply current and the current required by the charger. The MAX1909 reduces the source current by decreasing the charge current when the input current exceeds the set input current limit. This technique does not truly limit the input current. As the system supply current rises, the available charge current drops proportionally to zero. Thereafter, the total input current can increase without limit. An internal amplifier compares the differential voltage between CSSP and CSSN to a scaled voltage set with the CLS input. VCLS can be driven directly or set with a resistive voltage-divider between REF and GND. Connect CLS to REF to set the input current-limit sense voltage to the maximum value of 75mV. Calculate the input current as follows: IIN = 0.075 VCLS × RS1 VREF V CLS determines the reference voltage of the GMS error amplifier. Sense resistor RS1 sets the maximum allowable source current. Once the input current limit is reached, the charge current is decreased linearly until the input current is below the desired threshold. Duty cycle affects the accuracy of the input current limit. AC load current also affects accuracy (see Typical Operating Characteristics). Refer to the MAX1909 EV kit data sheet for more details on reducing the effects of switching noise. When choosing the current-sense resistor RS1, carefully calculate its power rating. Take into account variations in the system’s load current and the overall accuracy of the sense amplifier. Note that the voltage drop across RS1 contributes additional power loss, which reduces efficiency. System currents normally fluctuate as portions of the system are powered up or put to sleep. Without input current regulation, the input source must be able to deliver the maximum system current and the maximum charger input current. By using the input current-limit circuit, the output current capability of the AC wall adapter can be lowered, reducing system cost. Current Measurement The MAX1909 includes an input current monitor IINP. The current delivered at the IINP output is a scaleddown replica of the system load current plus the inputreferred charge current that is sensed across CSSP and CSSN inputs. The output voltage range is 0 to 3V. The voltage of IINP is proportional to the output current according to the following equation: VIINP = ISOURCE ✕ RS1 ✕ GIINP ✕ R9 where ISOURCE is the DC current supplied by the AC adapter power, GIINP is the transconductance of IINP (3mA/V typ), and R9 is the resistor connected between IINP and ground. Leave the IINP pin unconnected if not used. LDO Regulator LDO provides a 5.4V supply derived from DCIN and can deliver up to 10mA of extra load current. The lowside MOSFET driver is powered by DLOV, which must be connected to LDO as shown in Figure 1. LDO also supplies the 4.2235V reference (REF) and most of the control circuitry. Bypass LDO with a 1µF capacitor. Shutdown and Charge Inhibit (PKPRES) When the AC adapter is removed, the MAX1909 shuts down to a low-power state that does not significantly load the battery. Under these conditions, a maximum of 6µA is drawn from the battery through the combined load of the SRC, CSSP, CSSN, CSIP, CSIN, and BATT inputs. The charger enters this low-power state when DCIN falls below the undervoltage lockout (UVLO) threshold of 7V. The PDS switch turns off, the PDL switch turns on, and the system runs from the battery. The body diode of the PDL switch prevents the voltage on the power source output from collapsing. Charging can also be inhibited by driving the pack detection input (PKPRES) high, which suspends switching and pulls CCI, CCS, and CCV to ground. The PDS and PDL drivers, LDO, input current monitor, and control logic (ACOK) all remain active in this state. Approximately 3mA of supply current is drawn from the AC adapter and 3µA (max) is drawn from the battery to support these functions. The threshold voltage of PKPRES is 90% of VLDO (typ), with hysteresis of 1% VLDO to prevent erratic transitions. In smart-battery systems, PKPRES is usually driven from a voltage-divider formed with a low-value resistor or PTC thermistor inside the battery back and a local resistive pullup. This arrangement automatically detects the presence of a battery. A PTC thermistor can be used to shut down the MAX1909 when the battery pack is hot (see the Thermal Charge Qualification section). ______________________________________________________________________________________ 17 MAX1909 current. The sense resistor’s I2R power loss reduces charger efficiency. Adjusting ICTL to drop the voltage across the current-sense resistor improves efficiency, but may degrade accuracy due to the current-sense amplifier’s input offset error. The charge-current error amplifier (GMI) is compensated at the CCI pin. See the Compensation section. MAX1909 Multichemistry Battery Charger with Automatic System Power Selector A third method for inhibiting charging is to force ICTL below 0.8V (typ). Approximately 3mA of supply current is drawn from the AC adapter and 3µA is drawn from the battery when the MAX1909 is in this state. AC Adapter Detection and Power-Source Selection The MAX1909 includes a hysteretic comparator that detects the presence of an AC power adapter and automatically delivers power to the system load from the appropriate available power source. When the adapter is present, the open-drain ACOK output becomes a high impedance. The switch threshold at ACIN is 2.048V. Use a resistive voltage-divider from the adapter’s output to the ACIN pin to set the appropriate detection threshold. When charging, the battery is isolated from the system load with the P-channel PDL switch, which is biased off. When the adapter is absent, the drives to the switches change state in a fast breakbefore-make sequence. PDL begins to turn on 7.5µs after PDS begins to turn off. The threshold for selecting between the PDL and PDS switches is set based on the voltage difference between the DCIN and the BATT pins. If this voltage difference drops below 100mV, the PDS is switched off and PDL is switched on. Under these conditions, the MAX1909 is completely powered down. The PDL switch is kept on with a 100kΩ pulldown resistor when the charger is powered down through ICTL, PKPRES, or the AC adapter is removed. The drivers for PDL and PDS are fully integrated. The positive bias inputs for the drivers connect to the SRC pin and the negative bias inputs connect to a negative regulator referenced to SRC. With this arrangement, the drivers can swing from SRC to approximately 10V below SRC. Conditioning Mode The MAX1909 can be programmed to perform a conditioning cycle to calibrate the battery’s fuel gauge. This cycle consists of isolating the battery from the charger and discharging it through the system load. When the battery reaches 100% depth of discharge, it is then recharged. Driving the MODE pin low places the MAX1909 in conditioning mode, which stops the charger from switching, turns the PDS switch off, and turns the PDL switch on. To utilize the conditioning mode function, the configuration of the PDS switch must be changed to two sourceconnected FETs to prevent the AC adapter from supplying current to the system through the MOSFET’s 18 body diode. See Figure 2. The SRC pin must be connected to the common source node of the back-to-back FETs to properly drive the MOSFETs. It is essential to alert the user that the system is performing a conditioning cycle. If the user terminates the cycle prematurely, the battery can be discharged even though the system was running off AC adapter for a substantial period of time. If the AC adapter is in fact removed during conditioning, the MAX1909 keeps the PDL switch on and the charger remains off as it would in normal operation. If the battery is removed during conditioning mode, the PKPRES control overrides conditioning mode. When MODE is grounded and PKPRES goes high, the PDS switch starts turning on within 7.5µs and the system is powered from the AC adapter. DC-to-DC Converter The MAX1909 employs a buck regulator with a PMOS high-side switch and a low-side NMOS synchronous rectifier. The MAX1909 features a pseudo-fixed-frequency, cycle-by-cycle current-mode control scheme. The off-time is dependent upon VDCIN, VBATT, and a time constant, with a minimum t OFF of 300ns. The MAX1909 can also operate in discontinuous conduction for improved light-load efficiency. The operation of the DC-to-DC controller is determined by the following four comparators as shown in Figure 4: • CCMP: Compares the control point (lowest voltage clamp (LVC)) against the charge current (CSI). The high-side MOSFET on-time is terminated if the CCMP output is high. • IMIN: Compares the control point (LVC) against 0.15V (typ). If IMIN output is low, then a new cycle cannot begin. This comparator determines whether the regulator operates in discontinuous mode. • IMAX: Compares the charge current (CSI) to the internally fixed cycle-by-cycle current limit. The current-sense voltage limit is 97mV. With RS2 = 0.015Ω,this corresponds to 6A. The high-side MOSFET on-time is terminated if the IMAX output is high and a new cycle cannot begin until IMAX goes low. IMAX protects against sudden overcurrent faults. • ZCMP: Compares the charge current (CSI) to 333mA (RS2 = 0.015Ω). The current-sense voltage threshold is 5mV. If ZCMP output is high, then both MOSFETs are turned off. The ZCMP comparator terminates the switch on-time in discontinuous mode. ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector MAX1909 AC ADAPTER CSSP CSSN MAX1909 DHI CSS 20X DHI IMAX 1.94V R Q S Q COMP DLO DLO IMIN 0.15V TOFF ZCMP 0.1V LVC CLS GMS ICTL CSIP LVC GMI CSI 20X CSIN VCTL GMV CCV CCI CCS BATT COUT RCCV CCV CCI CCS Figure 4. DC-to-DC Converter Functional Diagram ______________________________________________________________________________________ 19 MAX1909 Multichemistry Battery Charger with Automatic System Power Selector CCV, CCI, CCS, and LVC Control Blocks The MAX1909 controls charge voltage (CCV control loop), charge current (CCI control loop), or input current (CCS control loop), depending on the operating conditions. The three control loops, CCV, CCI, and CCS, are brought together internally at the LVC amplifier. The output of the LVC amplifier is the feedback control signal for the DC-to-DC controller. The minimum voltage at CCV, CCI, or CCS appears at the output of the LVC amplifier and clamps the other two control loops to within 0.3V above the control point. Clamping the other two control loops close to the lowest control loop ensures fast transition with minimal overshoot when switching between different control loops (see the Compensation section). Continuous Conduction Mode With sufficient battery current loading, the MAX1909’s inductor current never reaches zero, which is defined as continuous conduction mode. If the BATT voltage is within the following range: 3.1V ✕ (number of cells) < VBATT < (0.88 ✕ VDCIN) The regulator is not in dropout and switches at fNOM = 400kHz. The controller starts a new cycle by turning on the high-side P-channel MOSFET and turning off the low-side N-channel MOSFET. When the charge current is greater than the control point (LVC), CCMP goes high and the off-time is started. The off-time turns off the high-side P-channel MOSFET and turns on the low-side N-channel MOSFET. The operating frequency is governed by the off-time and is dependent upon VDCIN and VBATT. The off-time is set by the following equation: t OFF = 1 VCSSN − VBATT fNOM VCSSN where fNOM = 400kHz: V ×t where IRIPPLE = BATT OFF L 1 t ON + t OFF These equations describe the controller’s pseudo-fixedfrequency performance over the most common operating conditions. 20 Discontinuous Conduction The MAX1909 enters discontinuous conduction mode when the output of the LVC control point falls below 0.15V. For RS2 = 0.015Ω, this corresponds to 0.5A: 0.15V IMIN = = 0.5A 20 × RS2 where RS2 = 0.015Ω. In discontinuous mode, a new cycle is not started until the LVC voltage rises above 0.15V. Discontinuous mode operation can occur during conditioning charge of overdischarged battery packs, when the charge current has been reduced sufficiently by the CCS control loop, or when the charger is in constant voltage mode with a nearly full battery pack. Compensation L × IRIPPLE t ON = VCSSN − VBATT f= At the end of the fixed off-time, the controller can initiate a new cycle if the control point (LVC) is greater than 0.15V (IMIN = high) and the peak charge current is less than the cycle-by-cycle limit (IMAX = low). If the charge current exceeds IMAX, the on-time is terminated by the IMAX comparator. If during the off-time the inductor current goes to zero, ZCMP = high, both the high- and low-side MOSFETs are turned off until another cycle is ready to begin. This condition is discontinuous conduction. See the Discontinuous Conduction section. There is a minimum 0.3ms off-time when the (VDCIN VBATT) differential becomes too small. If VBATT ≥ 0.88 x V DCIN , then the threshold for minimum off-time is reached and the tOFF is fixed at 0.3ms. The switching frequency in this mode varies according to the equation: 1 f= L × IRIPPLE + 0.3µs (VCSSN − VBATT ) The charge voltage, charge current, and input currentlimit regulation loops are compensated separately and independently at the CCV, CCI, and CCS pins. CCV Loop Compensation The simplified schematic in Figure 5 is sufficient to describe the operation of the MAX1909 when the voltage loop (CCV) is in control. The required compensation network is a pole-zero pair formed with CCV and RCV. The pole is necessary to roll off the voltage loop’s response at low frequency. The zero is necessary to compensate the pole formed by the output capacitor and the load. RESR is the equivalent series resistance (ESR) of the charger output capacitor (COUT). RL is the equivalent charger output load, where RL = ∆VBATT / ∆ICHG. ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector RL RCV ROGMV × (1+ sCCV × RCV ) (1+ sCOUT × RL ) RESR RL COUT GMV where ACSI = 20, and RS2 = 0.015Ω in the Typical Application Circuits, so GMOUT = 3.33A/V. The loop transfer function is: LTF = GMOUT × BATT GMOUT CCV 1 GMOUT = A CSI × RS2 MAX1909 The equivalent output impedance of the GMV amplifier, R OGMV , is greater than 10MΩ. The voltage loop transconductance (GMV = ICCV/VBATT) depends on the MODE input, which determines the number of cells. GMV = 0.125mA/mV for 4 cells and GMV = 0.167mA/mV for 3 cells. The DC-to-DC converter transconductance is dependent upon the charge current-sense resistor RS2: (1+ sCCV × ROGMV ) GMV (1+ sCOUT × RESR ) × The poles and zeros of the voltage-loop transfer function are listed from lowest frequency to highest frequency in Table 1. Near crossover, C CV has a much lower impedance than ROGMV. Since CCV is in parallel with ROGMV, CCV dominates the parallel impedance near crossover. Additionally, RCV has a much higher impedance than CCV and dominates the series combination of RCV and CCV, so: ROGMV REF CCV Figure 5. CCV Loop Diagram ROGMV × (1+ sCCV × RCV ) (1+ sCCV × ROGMV ) ≅ RCV COUT also has a much lower impedance than RL near crossover, so the parallel impedance is mostly capacitive and: 1 RL ≅ 1 + × sC R sC ( OUT L) OUT If RESR is small enough, its associated output zero has a negligible effect near crossover and the loop-transfer function can be simplified as follows: Table 1. Poles and Zeros of the Voltage-Loop Transfer Function NO. 1 NAME CALCULATION fP _ CV = CCV pole 2πROGMV × CCV 1 fZ _ CV = 2πRCV × CCV 2 CCV zero 3 Output pole 4 1 Output zero fP _ OUT = 1 2πRL × COUT 1 fZ _ OUT = 2πRESR × COUT DESCRIPTION Lowest frequency pole created by CCV and GMV’s finite output resistance. Since ROGMV is very large and not well controlled, the exact value for the pole frequency is also not well controlled (ROGMV > 10MΩ). Voltage-loop compensation zero. If this zero is at the same frequency or lower than the output pole fP_OUT, then the loop transfer function approximates a single pole response near the crossover frequency. Choose CCV to place this zero at least one decade below crossover to ensure adequate phase margin. Output pole formed with the effective load resistance RL and the output capacitance COUT. RL influences the DC gain but does not affect the stability of the system or the crossover frequency. Output ESR Zero. This zero can keep the loop from crossing unity gain if fZ_OUT is less than the desired crossover frequency; therefore, choose a capacitor with an ESR zero greater than the crossover frequency. ______________________________________________________________________________________ 21 where CCV ≥ 4nF (assuming 4 cells and 4A maximum charge current). Figure 6 shows the Bode plot of the voltage-loop frequency response using the values calculated above. RCV LTF = GMOUT × GMV sCOUT Setting the LTF = 1 to solve for the unity gain frequency yields: fCO _ CV = GMOUT × GMV RCV 2π × C OUT For stability, choose a crossover frequency lower than 1/10th of the switching frequency. Choosing a crossover frequency of 30kHz and solving for R CV using the component values listed in Figure 1 yields: MODE = VCC (4 cells) GMV = 0.125µA/mV COUT = 22µF VBATT = 16.8V LTF = GMOUT × A CSI × RS2 × GMI fCO_CV = 30kHz 2π × COUT × fCO _ CV = 10kΩ GMV × GMOUT the loop transfer function simplifies to: To ensure that the compensation zero adequately cancels the output pole, select fZ_CV ≤ fP_OUT: CCV ≥ (RL/RCV) COUT 80 ROGMI 1+ sROGMI × CCI This describes a single pole system. Since: 1 GMOUT = A CSI × RS2 fOSC = 400kHz RCV = CCI Loop Compensation The simplified schematic in Figure 7 is sufficient to describe the operation of the MAX1909 when the battery current loop (CCI) is in control. Since the output capacitor’s impedance has little effect on the response of the current loop, only a single pole is required to compensate this loop. ACSI is the internal gain of the current-sense amplifier. RS2 is the charge currentsense resistor, RS2 = 15mΩ. ROGMI is the equivalent output impedance of the GMI amplifier, which is greater than 10MΩ. GMI is the charge current amplifier transconductance = 1µA/mV. GMOUT is the DC-to-DC converter transconductance = 3.3A/V. The loop transfer function is given by: RL = 0.2Ω GMOUT = 3.33A/V LTF = GMI ROGMI 1+ sROGMI × CCI 0 CSIP 60 CSIN GMOUT 40 -45 20 0 -90 -20 GMI -40 1 10 CSI CCI MAG PHASE 0.1 PHASE (DEGREES) RS2 MAGNITUDE (dB) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector 100 1k 10k 100k -135 1M CCI ROGMI FREQUENCY (Hz) Figure 6. CCV Loop Response 22 ICTL Figure 7. CCI Loop Diagram ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector MAX1909 The crossover frequency is given by: ADAPTER INPUT GMI fCO _ CI = 2πCCI CSSP CLS For stability, choose a crossover frequency lower than 1/10th of the switching frequency: CCI = GMI / (2π fO_CI) RS1 CSSN GMS Choosing a crossover frequency of 30kHz and using the component values listed in Figure 1 yields CCI > 5.4nF. Values for CCI greater than 10 times the minimum value may slow down the current-loop response excessively. Figure 8 shows the Bode plot of the current-loop frequency response using the values calculated above. CCS Loop Compensation The simplified schematic in Figure 9 is sufficient to describe the operation of the MAX1909 when the input current-limit loop (CCS) is in control. Since the output capacitor’s impedance has little effect on the response of the input current-limit loop, only a single pole is required to compensate this loop. ACSS is the internal gain of the current-sense amplifier. RS1 is the input current-sense resistor; RS1 = 10mΩ in the Typical Applications Circuits. ROGMS is the equivalent output impedance of the GMS amplifier, which is greater than 10MΩ. GMS is the charge-current amplifier transconductance = 1µA/mV. GMIN is the DC-to-DC converter’s input-referred transconductance = (1/D) GM OUT = (1/D) 3.3A/V. CSS CCS GMIN CCS ROGMS SYSTEM LOAD Figure 9. CCS Loop Diagram The loop transfer function is given by: LTF = GMIN × A CSS × RS1× GMS ROGMS 1+ sROGMS × CCS Since: GMIN = 1 A CSS × RS1 the loop transfer function simplifies to: LTF = GMS ROGMS 1+ sROGMS × CCS The crossover frequency is given by: 100 60 40 -45 20 0 -20 -40 0.1 10 1k FREQUENCY (Hz) Figure 8. CCI Loop Response 100k -90 10M PHASE (DEGREES) MAG PHASE 80 MAGNITUDE (dB) fCO _ CS = 0 GMS 2πCCS For stability, choose a crossover frequency lower than 1/10th the switching frequency: CCS = GMS / (2π fCO_CS) Choosing a crossover frequency of 30kHz and using the component values listed in Figure 1 yields CCS > 5.4nF. Values for CCI greater than 10 times the minimum value may slow down the current-loop response excessively. Figure 10 shows the Bode plot of the input current-limit loop frequency response using the values calculated above. MOSFET Drivers The DHI and DLO outputs are optimized for driving moderately sized power MOSFETs. The MOSFET drive ______________________________________________________________________________________ 23 100 0 MAG PHASE MAGNITUDE (dB) 80 60 40 -45 20 PHASE (DEGREES) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector 0 -20 -40 0.1 10 1k 100k -90 10M FREQUENCY (Hz) Figure 10. CCS Loop Response capability is the same for both the low-side and highside switches. This is consistent with the variable duty factor that occurs in the notebook computer environment where the battery voltage changes over a wide range. An adaptive dead-time circuit monitors the DLO output and prevents the high-side FET from turning on until DLO is fully off. There must be a low-resistance, low-inductance path from the DLO driver to the MOSFET gate for the adaptive dead-time circuit to work properly. Otherwise, the sense circuitry in the MAX1909 interprets the MOSFET gate as “off” while there is still charge left on the gate. Use very short, wide traces measuring 10 squares to 20 squares or less (1.25mm to 2.5mm wide if the MOSFET is 25mm from the device). Unlike the DLO output, the DHI output uses a fixeddelay 50ns time to prevent the low-side FET from turning on until DHI is fully off. The same layout considerations should be used for routing the DHI signal to the high-side FET. Since the transition time for a P-channel switch can be much longer than an N-channel switch, the dead time prior to the high-side PMOS turning on is more pronounced than in other synchronous step-down regulators, which use high-side N-channel switches. On the high-to-low transition, the voltage on the inductor’s “switched” terminal flies below ground until the low-side switch turns on. A similar dead-time spike occurs on the opposite low-to-high transition. Depending upon the magnitude of the load current, these spikes usually have a minor impact on efficiency. The high-side driver (DHI) swings from SRC to 5V below SRC and typically sources 0.9A and sinks 0.5A 24 from the gate of the P-channel FET. The internal pulldown transistors that drive DHI high are robust, with a 2.0Ω (typ) on-resistance. The low-side driver (DLO) swings from DLOV to ground and typically sources 0.5A and sinks 0.9A from the gate of the N-channel FET. The internal pulldown transistors that drive DLO low are robust, with a 1.0Ω (typ) onresistance. This helps prevent DLO from being pulled up when the high-side switch turns on, due to capacitive coupling from the drain to the gate of the low-side MOSFET. This places some restrictions on the FETs that can be used. Using a low-side FET with smaller gate-to-drain capacitance can prevent these problems. Table 2. Recommended Components REFERENCE QTY DESCRIPTION 2 22µF ±20%, 35V E-size low-ESR tantalum capacitors AVX TPSE226M035R0300 Kemet T495X226M035AS 2 1µF ±10%, 25V, X7R ceramic capacitors (1206) Murata GRM31MR71E105K Taiyo Yuden TMK316BJ105KL TDK C3216X7R1E105K 2 0.01µF ±10%, 25V, X7R ceramic capacitors (0402) Murata GRP155R71E103K TDK C1005X7R1E103K 3 0.1µF ±10%, 25V, X7R ceramic capacitors (0603) Murata GRM188R71E104K TDK C1608X7R1E104K 3 1µF ±10%, 6.3V, X5R ceramic capacitors (0603) Murata GRM188R60J105K Taiyo Yuden JMK107BJ105KA TDK C1608X5R1A105K D4 1 Schottky diode, 0.5A, 30V SOD-123 Diodes Inc. B0530W General Semiconductor MBR0530 ON Semiconductor MBR0530 D5 1 25V ±1% zener diode CMDZ5253B L1 1 10µH, 4.4A inductor Sumida CDRH104R-100NC TOKO 919AS-100M C1, C4 C5, C15 C9, C10 C11, C14, C17 C12, C13, C16 ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector REFERENCE QTY DESCRIPTION N1/P1 1 Dual N- and P-channel MOSFETs, 7A, 30V and -5A, -30V, 8-pin SO, MOSFET Fairchild FDS8958A or Single N-channel MOSFETs, +13.5A, +30V FDS6670S and Single P-channel MOSFETs, -13.5A, -30V FDS66709Z P2, P3, P4 3 Single, P-channel, -11A, -30V, 8-pin SO MOSFETs Fairchild FDS6675 R4 1 100kΩ, ±5% resistor (0603) R5, R9, R21 2 10kΩ ±1% resistors (0603) R6 1 590kΩ ±1% resistor 0603 R7 1 196kΩ ±1% resistor 0603 R8 1 1MΩ ±5% resistor (0603) R11 1 1kΩ ±5% resistor (0603) R16 1 33Ω ±5% resistor (0603) R19, R20 2 10kΩ ±5% resistors (0603) RS1 1 0.01Ω ±1%, 0.5W sense resistor (2010) Vishay Dale WSL2010 0.010 1.0% IRC LRC-LR2010-01-R010-F RS2 1 0.015Ω ±1%, 0.5W sense resistor (2010) Vishay Dale WSL2010 0.015 1.0% IRC LRC-LR2010-01-R015-F U1 1 MAX1909ETI (28-pin thin QFN-EP) Design Procedure Table 2 lists the recommended components and refers to the circuit of Figure 2. The following sections describe how to select these components. MOSFET Selection MOSFETs P2 and P3 (Figure 1) provide power to the system load when the AC adapter is inserted. These devices may have modest switching speeds, but must be able to deliver the maximum input current as set by RS1. As always, care should be taken not to exceed the device’s maximum voltage ratings or the maximum operating temperature. The P-channel/N-channel MOSFETs (P1, N1) are the switching devices for the buck controller. The guidelines for these devices focus on the challenge of obtaining high load-current capability when using highvoltage (>20V) AC adapters. Low-current applications usually require less attention. The high-side MOSFET (P1) must be able to dissipate the resistive losses plus the switching losses at both V DCIN(MIN) and VDCIN(MAX). Ideally, the losses at V DCIN(MIN) should be roughly equal to losses at V DCIN(MAX), with lower losses in between. If the losses at VDCIN(MIN) are significantly higher than the losses at VDCIN(MAX), consider increasing the size of P1. Conversely, if the losses at VDCIN(MAX) are significantly higher than the losses at VDCIN(MIN), consider reducing the size of P1. If DCIN does not vary over a wide range, the minimum power dissipation occurs where the resistive losses equal the switching losses. Choose a low-side MOSFET that has the lowest possible on-resistance (RDS(ON)), comes in a moderatesized package, and is reasonably priced. Make sure that the DLO gate driver can supply sufficient current to support the gate charge and the current injected into the parasitic gate-to-drain capacitor caused by the high-side MOSFET turning on; otherwise, cross-conduction problems can occur. The MAX1909 has an adaptive dead-time circuit that prevents the high-side and low-side MOSFETs from conducting at the same time (see MOSFET Drivers). Even with this protection, it is still possible for delays internal to the MOSFET to prevent one MOSFET from turning off when the other is turned on. Select devices that have low turn-off times. To be conservative, make sure that P1(t DOFF (MAX)) N1(tDON(MIN)) < 40ns. Failure to do so may result in efficiency-killing shoot-through currents. If delay mismatch causes shoot-through currents, consider adding extra capacitance from gate to source on N1 to slow down its turn-on time. MOSFET Power Dissipation Worst-case conduction losses occur at the duty factor extremes. For the high-side MOSFET, the worst-case power dissipation (PD) due to resistance occurs at the minimum supply voltage: V I 2 PD(P1) = BATT LOAD × RDS(ON) VDCIN 2 Generally, a small high-side MOSFET is desired to reduce switching losses at high input voltages. However, the RDS(ON) required to stay within package power-dissipation limits often limits how small the MOSFET can be. The optimum occurs when the switching (AC) losses equal the conduction (I 2 R DS(ON) ) losses. High-side switching losses do not usually become an issue until the input is greater than approxi- ______________________________________________________________________________________ 25 MAX1909 Table 2. Recommended Components (continued) mately 15V. Switching losses in the high-side MOSFET can become an insidious heat problem when maximum AC adapter voltages are applied, due to the squared term in the CV2 f switching-loss equation. If the highside MOSFET that was chosen for adequate RDS(ON) at low supply voltages becomes extraordinarily hot when subjected to VDCIN(MAX), then choose a MOSFET with lower losses. Calculating the power dissipation in P1 due to switching losses is difficult since it must allow for difficult quantifying factors that influence the turn-on and turn-off times. These factors include the internal gate resistance, gate charge, threshold voltage, source inductance, and PC board layout characteristics. The following switching-loss calculation provides only a very rough estimate and is no substitute for breadboard evaluation, preferably including a verification using a thermocouple mounted on P1: PD(P1_ Switching) = VDCIN(MAX)2 × CRSS × fSW × ILOAD 2 IGATE 1.5 3 CELLS 4 CELLS RIPPLE CURRENT (A) MAX1909 Multichemistry Battery Charger with Automatic System Power Selector 1.0 0.5 VDCIN = 19V VCTL = ICTL = LDO 0 8 9 10 11 12 13 14 15 16 17 18 VBATT (V) Figure 11. Ripple Current vs. Battery Voltage V I 2 PD(N1) = 1− BATT LOAD × RDS(ON) VDCIN 2 tOFF = 0.3us for VBATT > 0.88 VDCIN Figure 11 illustrates the variation of the ripple current vs. battery voltage when the circuit is charging at 3A with a fixed input voltage of 19V. Higher inductor values decrease the ripple current. Smaller inductor values require high-saturation current capabilities and degrade efficiency. Designs that set LIR = ∆IL/ICHG = 0.3 usually result in a good balance between inductor size and efficiency. Choose a Schottky diode (D1, Figure 2) having a forward voltage low enough to prevent the N1 MOSFET body diode from turning on during the dead time. As a general rule, a diode with a DC current rating equal to 1/3rd the load current is sufficient. This diode is optional and can be removed if efficiency is not critical. The input capacitor must meet the ripple current requirement (IRMS) imposed by the switching currents. Nontantalum chemistries (ceramic, aluminum, or OSCON) are preferred due to their resilience to power-up surge currents. where CRSS is the reverse transfer capacitance of P1, and IGATE is the peak gate-drive source/sink current. For the low-side MOSFET (N1), the worst-case power dissipation always occurs at maximum input voltage: Inductor Selection The charge current, ripple, and operating frequency (off-time) determine the inductor characteristics. Inductor L1 must have a saturation current rating of at least the maximum charge current plus 1/2 of the ripple current (∆IL): ISAT = ICHG + (1/2) ∆IL The ripple current is determined by: ∆IL = VBATT tOFF / L where: tOFF = 2.5us (VDCIN - VBATT) / VDCIN for VBATT < 0.88 VDCIN or: 26 Input Capacitor Selection V BATT (VDCIN − VBATT ) IRMS = ICHG VDCIN The input capacitors should be sized so that the temperature rise due to ripple current in continuous conduction does not exceed about 10°C. The maximum ripple current occurs at 50% duty factor or VDCIN = 2 ✕ VBATT, which equates to 0.5 ✕ ICHG. If the application of interest does not achieve the maximum value, size the input capacitors according to the worst-case conditions. Output Capacitor Selection The output capacitor absorbs the inductor ripple current and must tolerate the surge current delivered from the battery when it is initially plugged into the charger. ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector BATTERY MAX1909 It is desirable to charge deeply discharged batteries at a low rate to improve cycle life. The MAX1909 automatically reduces the charge current when the voltage per cell is below 3.1V. The charge current-sense voltage is set to 4.5mV (ICHG = 300mA with RS2 = 15mΩ) until the battery voltage rises above the threshold. There is approximately 300mV for 3 cell, 400mV for 4 cell of hysteresis to prevent the charge current magnitude from chattering between the two values. Thermal Charge Qualification Based on the cell characteristics, the MAX1909 should not charge batteries operating above a specified temperature. Often a PTC thermistor is included inside the battery pack to measure its temperature. When connected to the charger, the thermistor forms a voltagedivider with a resistive pullup to the LDO. The threshold voltage of PKPRES is 90% of VLDO (typ), with hysteresis of 1% of VLDO to prevent erratic transitions. The thermistor can be selected to have a resistance vs. temperature characteristic that abruptly increases above a critical temperature. This arrangement automatically shuts down the MAX1909 when the battery pack is above a critical temperature. For the example shown in Figure 12, a Thermometrics YSC060 device is selected with the thermal threshold of approximately +60°C. Layout and Bypassing Bypass DCIN with a 1µF capacitor to ground (Figure 1). D4 protects the MAX1909 when the DC power source input is reversed. A signal diode for D4 is adequate because DCIN only powers the LDO and the internal reference. Bypass LDO, DHIV, DLOV, and other pins as shown in Figure 1. Good PC board layout is required to achieve specified noise, efficiency, and stable performance. The PC board layout artist must be given explicit instructions— preferably, a sketch showing the placement of the power-switching components and high-current routing. LDO LDO CLDO 1µF Applications Information Startup Conditioning Charge for Overdischarged Cells MAX1909 As such, both capacitance and ESR are important parameters in specifying the output capacitor as a filter and to ensure the stability of the DC-to-DC converter. (See the Compensation section.) Beyond the stability requirements, it is often sufficient to make sure that the output capacitor’s ESR is much lower than the battery’s ESR. Either tantalum or ceramic capacitors can be used on the output. Ceramic devices are preferable because of their good voltage ratings and resilience to surge currents. TEMP R1 10kΩ R2 70kΩ PKPRES THERMISTER Figure 12. Use of a PTC Thermistor for Thermal Change Qualification Refer to the PC board layout in the MAX1909 evaluation kit for examples. A ground plane is essential for optimum performance. In most applications, the circuit is located on a multilayer board, and full use of the four or more copper layers is recommended. Use the top layer for high-current connections, the bottom layer for quiet connections, and the inner layers for an uninterrupted ground plane. Use the following step-by-step guide: 1) Place the high-power connections first, with their grounds adjacent: a) Minimize the current-sense resistor trace lengths, and ensure accurate current sensing with Kelvin connections. b) Minimize ground trace lengths in the high-current paths. c) Minimize other trace lengths in the high-current paths. d) Use > 5mm wide traces. e) Connect C1 and C2 to the high-side MOSFET (10mm max length). Return these capacitors to the power ground plane. f) Minimize the LX node (MOSFETs, rectifier cathode, inductor (15mm max length)). Ideally, surface-mount power components are flush against one another with their ground terminals almost touching. These high-current grounds are then connected to each other with ______________________________________________________________________________________ 27 MAX1909 Multichemistry Battery Charger with Automatic System Power Selector a wide, filled zone of top-layer copper, so they do not go through vias. The resulting top-layer ground plane is connected to the normal inner-layer ground plane at the output ground terminals, which ensures that the IC’s analog ground is sensing at the supply’s output terminals without interference from IR drops and ground noise. Other high-current paths should also be minimized, but focusing primarily on short ground and current-sense connections eliminates about 90% of all PC board layout problems. 2) Place the IC and signal components. Keep the main switching node (LX node) away from sensitive analog components (current-sense traces and REF capacitor). Important: The IC should be less than 10mm from the current-sense resistors. VIA CONNECTING POWER GROUND TO QUIET ANALOG GROUND HIGH-CURRENT PGND PLANE QUIET GROUND ISLAND Quiet connections to REF, VCTL, ICTL, CCV, CCI, CCS, IINP, ACIN, and DCIN should be returned to a separate ground (GND) island. The appropriate traces are marked on the schematic with the ground symbol ( ). There is very little current flowing in these traces, so the ground island need not be very large. When placed on an inner layer, a sizable ground island can help simplify the layout because the low-current connections can be made through vias. The ground pad on the backside of the package should also be connected to this quiet ground island. 3) Keep the gate drive traces (DHI and DLO) as short as possible (L < 20mm), and route them away from the current-sense lines and REF. These traces should also be relatively wide (W > 1.25mm). KELVIN-SENSE VIAS UNDER THE SENSE RESISTOR (REFER TO EVALUATION KIT) INDUCTOR COUT COUT CIN INPUT 4) Place ceramic bypass capacitors close to the IC. The bulk capacitors can be placed further away. 5) Use a single-point star ground placed directly below the part at the PGND pin. Connect the power ground (ground plane) and the quiet ground island at this location. See Figure 13. OUTPUT GND Figure 13. PC Board Layout Examples Chip Information TRANSISTOR COUNT: 2720 PROCESS: BiCMOS 28 ______________________________________________________________________________________ Multichemistry Battery Charger with Automatic System Power Selector b CL 0.10 M C A B D2/2 D/2 PIN # 1 I.D. QFN THIN.EPS D2 0.15 C A D k 0.15 C B PIN # 1 I.D. 0.35x45 E/2 E2/2 CL (NE-1) X e E E2 k L DETAIL A e (ND-1) X e CL CL L L e e 0.10 C A C 0.08 C A1 A3 PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE 16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm APPROVAL COMMON DIMENSIONS DOCUMENT CONTROL NO. REV. 21-0140 C 1 2 EXPOSED PAD VARIATIONS NOTES: 1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES. 3. N IS THE TOTAL NUMBER OF TERMINALS. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE. 5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm FROM TERMINAL TIP. 6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY. 7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION. 8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 9. DRAWING CONFORMS TO JEDEC MO220. 10. WARPAGE SHALL NOT EXCEED 0.10 mm. PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE 16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm APPROVAL DOCUMENT CONTROL NO. REV. 21-0140 C 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 29 © 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. MAX1909 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)