TELEDYNE RF170-12

TELEDYNE RELAYS
COMMERCIAL CENTIGRID®
MAGNETIC LATCHING
R.F. RELAYS
SERIES
RF170
DPDT
DESCRIPTION
• All welded construction.
• Unique uni-frame design providing high magnetic efficiency and
mechanical rigidity.
• High force/mass ratios for resistance to shock and vibration.
• Advanced cleaning techniques provide maximum assurance of
internal cleanliness.
• Gold plated precious metal alloy contacts ensure reliable d.c.
switching from dry-circuit to 1/4 amp, as well as low, stable
insertion loss.
The RF170 Series relay is an ultraminiature, hermetically sealed,
magnetic-latching relay featuring extremely low intercontact capacitance
for exceptional R.F. performance over the full UHF spectrum. Its low
profile height and .100" grid spaced terminals (precluding the need for
spreader pads) make it ideal for applications where extreme packaging
density and/or close PC board spacing are required.
The basic design and internal structure are similar to the TO-5 421
Series relay. In addition, the RF170 design has been optimized for use
in RF attenuators, RF switch matrices, and other applications requiring
high isolation, low insertion loss, and low VSWR.
The RF170 relay is ideally suited for applications where power dissipation
must be minimized. The relays can be operated with a short-duration
pulse. After the contacts have transferred, no external holding power is
required.
Unique construction features and manufacturing techniques provide
overall high reliability and excellent resistance to environmental
extremes.
The magnetic-latching feature of the RF170 Series provides a “memory”
capability, since the relays will not reset upon removal of coil power.
PRINCIPLE OF OPERATION
Energizing Coil B produces a magnetic
field opposing the holding flux of the
MAGNETIC CIRCUIT A
PERMANENT MAGNET
SOFT IRON CORE A
permanent magnet in Circuit B. As this
MAGNETIC CIRCUIT B
SOFT IRON FRAME
net holding force decreases, the attractive force in the air gap of Circuit A,
COIL A
COIL B
which also results from the flux of the
permanent magnet, becomes great
enough to break the armature free of
AIR GAP
Core B, and snap it into a closed position
STATIONARY
SOFT IRON
CONTACT
ARMATURE
against Core A. The armature then
remains in this position upon removal
of power from Coil B, but will snap back
MOVING
CONTACT
into position B upon energizing Coil A.
Since operation depends upon cancellation of a magnetic field, it is necessary
to apply the correct polarity to the relay coils as indicated on the relay schematic.
When latching relays are installed in equipment, the latch and reset coils should not be
pulsed simultaneously. Coils should not be pulsed with less than the nominal coil voltage and the pulse width should be a minimum of three times the specified operate time
of the relay. If these conditions are not followed, it is possible for the relay to be in the
magnetic neutral position.
87
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Temperature
(Ambient)
-55°C to + 85°C
Vibration
10 g’s to 1000 Hz
(Note 3)
Shock
30 g’s for 6 msec.
(Note 3)
Enclosure
Hermetically sealed
Weight
0.10 oz
(2.9 gms.) max.
SERIES RF170
GENERAL ELECTRICAL SPECIFICATIONS
(@ 25°C) (Notes 1 & 2)
Contact Arrangement
2 Form C (DPDT)
Rated Duty
Continuous
Contact Resistance
0.15 ohm max. before life; 0.25 ohm max. after life at 0.25A/28VDC, (measured 1/8” from header)
Contact Load Rating (DC)
Resistive:
Low Level:
Contact Life Ratings
10,000,000 cycles (typical) at low level
00,100,000 cycles min. at all other loads specified above
Contact Overload Rating
0.5A/28VDC Resistive (100 cycles min.)
Contact Carry Rating
Contact factory
Coil Operating Power
290 milliwatts typical at nominal rated voltage @ 25°C
Operate Time
2.0 msec max. at nominal rated coil voltage
Minimum Operate Pulse
6.0 msec max. at nominal voltage
lntercontact Capacitance
0.02 pf typical
Insulation Resistance
1,000 megohms min. between mutually isolated terminals
Dielectric Strength
Atmospheric pressure: 350 VRMS/60 Hz
DETAILED ELECTRICAL SPECIFICATIONS
(@ 25°C) (Note 2)
BASE PART
NUMBERS
Coil Voltage (VDC)
0.25 Amp/28VDC
10 to 50 µA/10 to 50 mV
➧
RF170-5
RF170-6
RF170-9
RF170-12
RF170-18
5.0
6.0
9.0
12.0
18.0
Nom.
Max.
RF170-26
26.5
6.0
8.0
12.0
16.0
24.0
32.0
Coil Resistance (Ohms ± 20%)
61
120
280
500
1130
2000
Set & Reset Voltage (VDC, Max.)
3.5
4.5
6.8
9.0
13.5
18.0
TYPICAL R.F. PERFORMANCE (NOTE 1)
OUTLINE DIMENSIONS
.335 MAX.
(8.51)
.435 MAX.
(11.05)
0
INSERTIO
.1
.300 MAX.
(7.62)
N LOSS
.2
.3
.75 MIN. (19.05)
20
RETUR
40
S
TACT
CON
OSS
ACR
N
POLES
ATIO
A C R O SS
ISOL
ATION
ISOL
50
60
0.5
.1
.5
(0.43) + (0.051)
– (0.025)
10 LEADS
1.07
70
.01
DIA.
1.22
R)
S (VSW
N LOS
30
1.0
1.02
1.01
.375 MAX.
(9.53)
(.031 ± .003)
(0.79 ± 0.08)
0.17 + .002
– .001
1.92
10
VSWR
dB
.4
10
9
.100 TYP. (2.54)
1.00
1.00
4.0
FREQUENCY (GHz)
.035 ± .010
(0.89 ± 0.25)
1
COIL B
2
8
7
3
6
4
.475 MAX.
(12.06)
COIL A
5
PIN NUMBERS
FOR REF. ONLY
.200
(5.08)
SCHEMATIC
(TERMINAL VIEW) (NOTE 4)
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
NOTES:
1.
2.
3.
4.
Characteristics shown as “typical” are based on available data and are best estimates. No on-going verification tests are performed.
Unless otherwise specified, parameters are initial values.
Relays will exhibit no contact chatter in excess of 10 µsec or transfer in excess of 1 µsec.
Contacts shown in position resulting when Coil A last energized.
©1996
TELEDYNE RELAYS
88
12525 Daphne Avenue
Hawthorne, California 90250