TELEDYNE RELAYS SERIES S172 ® CENTIGRID SURFACE MOUNT COMMERCIAL RELAY DPDT SERIES DESIGNATION RELAY TYPE S172 DPDT basic relay S172D DPDT relay with internal diode for coil transient suppression DESCRIPTION INTERNAL CONSTRUCTION UNI-FRAME UPPER STATIONARY CONTACT ARMATURE LOWER STATIONARY CONTACT MOVING CONTACT ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Temperature (Ambient) -55°C to +85°C Vibration 10 g’s to 500 Hz (Note 3) Shock 30 g’s for 6 msec. (Note 3) half-sine Enclosure All welded, hermetically sealed Weight 0.15 oz (4.3 gms.) max. Reflow Temperature 260°C max. temp. 5 min. max. above 180°C The S172 Surface Mount Centigrid® relay is an ultraminiature, hermetically sealed, armature relay for commercial applications. Its low profile height (.470) and .100” grid spaced terminals, which precludes the need for spreader pads, makes it an ideal choice where extreme packaging density and/or close PC board spacing are required. The specially formed leads are pre-tinned to make the relays ideal for all types of surface mount solder reflow processes. The basic design and internal structure are similar to the Teledyne DPDT Centigrid® relay (114 Series). Unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to environmental extremes: • • • • • All welded construction. Unique uni-frame design providing high magnetic efficiency and mechanical rigidity. High force/mass ratios for resistance to shock and vibration. Advanced cleaning techniques provide maximum assurance of internal cleanliness. Precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. The S172 Series utilizes an internal discrete silicon diodes for coil suppression with electrical characteristics as specified herein. By virtue of its inherently low intercontact capacitance and contact circuit losses, the S172 relay is an excellent subminiature RF switch for frequency ranges well into the UHF spectrum (see Figure 1). Applications include telecommunications, test instruments, mobile communications, attenuators, and automatic test equipment. 94 SERIES S172 GENERAL ELECTRICAL SPECIFICATIONS Contact Arrangement Rated Duty Contact Resistance Contact Load Ratings (DC) (See Fig. 2 for other DC resistive voltage/current ratings) (@ 25°C) (Notes 1 & 2) 2 Form C (DPDT) Continuous 0.15 ohm max. before life; 0.3 ohm max. after life at 1A/28VDC, (measured 1/8” from header) Resistive: 1 Amp/28VDC Inductive: 200 mA/28VDC (320 mH) Lamp: 100 mA/28VDC Low Level: 10 to 50 µA/10 to 50 mV 5,000,000 cycles (typical) at low level 0,500,000 cycles (typical) at 0.5A/28VDC resistive 0,100,000 cycles min. at all other loads specified above 2A/28VDC Resistive (100 cycles min.) Contact factory 6.0 msec max. at nominal rated coil voltage S172: 3.0 msec max. S172D: 6.0 msec max. 0.4 pf typical 1,000 megohms min. between mutually isolated terminals Atmospheric pressure: 300 VRMS/60 Hz 60 VDC Min. 2.0 VDC Max. Contact Life Ratings Contact Overload Rating Contact Carry Rating Operate Time Release Time lntercontact Capacitance Insulation Resistance Dielectric Strength Diode P.I.V. S172D Negative Coil Transient S172D DETAILED ELECTRICAL SPECIFICATIONS (@ 25°C) (Note 2) ➧ GENERIC PART NUMBERS Coil Voltage (VDC) Nom. Max. Coil Resistance (Ohms ± 20%) Pick-up Voltage (VDC, Max.) Pulse Operation Coil Operating Power at Nominal Voltage (Milliwatts) S172-5 S172D-5 S172-12 S172D-12 S172-26 S172D-26 5.0 5.8 64 3.8 405 12.0 16.0 400 9.0 360 26.5 32.0 1600 18.0 440 TYPICAL DC CONTACT RATINGS (RESISTIVE) NOTES: 1. Characteristics shown as “typical” are based on available data and are best estimates. No on-going verification tests are performed. 2. Unless otherwise specified, parameters are initial values. 3. Relay contacts will exhibit no chatter in excess of 10 µsec or transfer in excess of 1 µsec. 4. Position of leads as they emerge from relay base. 5. Leads will fit noted pad layout with no overhang. 6. Lead ends are coplanar within .008” wide tolerance zone. 7. Terminals coated with SN60 or SN63 solder per QQ-S-571. Base material exposed at sheared end of leads. LOAD VOLTAGE (VDC) 300 250 200 150 100 50 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 LOAD CURRENT (AMPS DC) FIGURE 2 OUTLINE DIMENSIONS AND RECOMMENDED PAD LAYOUT (Notes 4, 5, 6 & 7) TERMINAL LOCATIONS AND SCHEMATIC DIAGRAMS .031 REF (.79) .035 REF (.89) .335 MAX (8.51) .280 MAX* (7.11) (9.60 +.76 ) –.51 .200 (5.08) 2 6 .100 TYP (2.54) .370** MAX (9.40) 2° ± 2° TYP 1 S172 .045 MIN 8 PL (1.14) Ø.017 REF (.43) 8 4° MAX TYP .200 (5.08) .410 MIN (10.41) .375 SQ MAX (9.53) +.030 .378 –.020 TYP 7 .100 4 PL (2.54) 4° MAX TYP 7 8 (–) 1 5 4 3 .200 (5.08) 2 6 * Unless otherwise specified .280” or .380” height may be supplied. To order the lower profile, add /28 to the part number. e.g. 172-26/28 (NOTE: /28 will not be marked on relay). Unless otherwise specified, relays may be supplied with either can height. ** Max. overall height for the higher profile S172 will be .470 (11.94) S172D RECOMMENDED PAD LAYOUT (NOTE 5) ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) 5 4 (+) 3 ©1996 TELEDYNE RELAYS 95 12525 Daphne Avenue Hawthorne, California 90250