FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Features Description 10µA Maximum ICCT Current over an Expanded Control Voltage Range: VIN = 2.6V, VCC = 3.6V) The FSUSB23 is a low-power, high-bandwidth analog switch specifically designed for high speed USB 2.0 applications. The FSUSB23 features very low quiescent current even when the control voltage is lower than the VCC supply. This feature services mobile handset applications, allowing direct interface with the baseband processor general-purpose I/Os. Lower Capacitance: CON = 9pF Typical 7Ω Typical On Resistance (RON) -3dB Bandwidth: > 720MHz Typical applications involve switching in portables and consumer applications, such as cell phones, digital cameras, and notebooks with hubs or controllers. The wide bandwidth (>720MHz) of this switch exceeds the bandwidth needed to pass the third harmonic, which results in signals with minimum edge and phase distortion. Superior channel-to-channel crosstalk results in minimal interference. Low Power Consumption: 1mA Maximum Wide -3db Bandwidth: > 720MHz Packaged in: - 10-Lead MicroPak™ (1.6 x 2.1mm) - 16-Lead DQFN (2.5 x3.5mm) 7kV I/O to GND ESD Performance Applications Cell phone, PDA, Digital Camera, and Notebook LCD Monitor, TV, and Set-Top Box Ordering Information Part Number Top Mark Operating Temperature Range FSUSB23L10X EZ -40 to +85°C 10-Lead MicroPak™ 1.6 x 2.1mm, JEDEC MO-255B -40 to +85°C 16-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC MO-241, 2.5 x 3.5mm FSUSB23BQX USB23 Package MicroPak™ is a trademark of Fairchild Semiconductor Corporation. All packages are lead free per JEDEC: J-STD-020B standard. D+ D1+ D2+ D- D1D2S /OE Control Figure 1. Analog Symbol © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch April 2008 Vcc /OE D1- D2- D-- D1+ 2 9 8 7 6 D2+ 3 5 10 3 VCC 1 16 15 /OE 14 D1- D+ 4 13 D2- NC 5 12 NC 6 11 NC D- D+ 4 D2+ 2 D1+ S 1 GND S 10 NC NC 7 Figure 2. Pad Assignments for MicroPak™ (Top Through View) 8 9 GND NC Figure 3. Pin Assignments for DQFN (Top Through View) FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Pin Configurations Pin Definitions Pin # Micropak Pin # DQFN Pin Name Pin Description 1 1 S Switch Select 9 15 /OE Bus Switch Enable 2, 3, 4 ,6, 7, 8 2, 3, 4, 12, 13, 14 D+, D-, Dn+, Dn- Data Port 10 16 VCC Supply Voltage 8 GND Ground 5, 6, 7, 9, 10, 11 NC No Connect 5 Truth Table Sel /OE Function X HIGH Disconnect LOW LOW D+, D- = D1n HIGH LOW D+, D- = D2n © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VCC Parameter Supply Voltage (1) VSW DC Switch Voltage VIN DC Input Voltage IIK DC Input Diode Current (1) Min. Max. Unit -0.5 4.6 V -0.5 VCC + 0.5 V -0.5 4.6 V -50 IOUT DC Output Current TSTG Storage Temperature ESD Human Body Model, JEDEC: JESD22-A114 -65 mA 50 mA +150 °C All Pins 7 I/O to GND 7 kV Note: 1. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. DC switch voltage may never exceed 4.6V. FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Absolute Maximum Ratings Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol VCC Parameter Supply Voltage VCNTRL Control Input Voltage VSW Switch Input Voltage (2)(3) TA Operating Temperature ΘJA Thermal Resistance Micropak Min. Max. Unit 3.0 3.6 V 0 VCC V 0 VCC V -40 +85 °C 250 °C/W Note: 2. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. DC switch voltage may never exceed 4.6V. 3. The control input must be held HIGH or LOW; it must not float. © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 3 All typical values are at 25°C unless otherwise specified. Symbol Parameter Conditions TA=- 40ºC to +85ºC Min. Typ. Clamp Diode Voltage VIH Input Voltage High 3.0 to 3.6 VIL Input Voltage Low 3.0 to 3.6 .50 V IIN Control Input Leakage VIN=0V to VCC 3.6 1 µA IOZ Off State Leakage 0 ≤ Dn, D1n, D2n ≤ VCC 1 µA RON Switch On Resistance RON Flat VSW =0.4V, ION=-8mA (4) VSW =0.8V, ION=-8mA (5) Delta RON RON Flatness 3.0 Units Max. VIK ∆RON IIN=-18mA VCC (V) (4) -1.2 1.2 V V 3.0 6 9 7 10 Ω VIN=0.4V, ION=-8mA 3.0 0.3 Ω VIN=0V-1.0V, ION=-8mA 3.0 2.0 Ω ICC Quiescent Supply Current VIN=0 or VCC, IOUT=0 3.6 1 µA ICCT Increase in ICC Current Per Control Voltage and VCC VIN=2.6V VCC=3.6V 3.6 10 µA Notes: 4. Measured by the voltage drop across the Dn, D1n, D2n pins at the indicated current through the switch. On resistance is determined by the lower of the voltage on the two (HSDn or Dn ports). 5. Guaranteed by characterization. FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch DC Electrical Characteristics AC Electrical Characteristics All typical values are for VCC=3.3V at 25°C unless otherwise specified. Symbol Parameter Conditions VCC (V) TA=- 40ºC to +85ºC Min. Typ. Max. Units tON Turn-On Time S, /OE to Output VD1n, D2n=0.8V, RL=50Ω, CL=10pF Figure 8 3.0 to 3.6 10 13 ns tOFF Turn-Off Time S, /OE to Output VD1n, D2n=0.8V, RL=50Ω, CL=10pF Figure 8 3.0 to 3.6 8 11 ns tPD Propagation Delay RL=50Ω, CL=10pF Figure 6, Figure 7 3.3 0.25 ns OIRR Off Isolation, Non-Adjacent f=250MHz, RT=50Ω Figure 14 3.0 to 3.6 -30 dB Xtalk Non-Adjacent Channel Crosstalk f=250MHz, RT=50Ω Figure 9 3.0 to 3.6 -43 dB BW -3db Bandwidth RT=50Ω Figure 13 3.0 to 3.6 720 MHz (6) Note: 6. Guaranteed by characterization. © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 4 Symbol Parameter Conditions VCC (V) TA=- 40ºC to +85ºC Min. Typ. Units Max. tSK(O) Channel-to-Channel Skew RL=50Ω, CL=10pF Figure 6, Figure 12 3.0 to 3.6 40 ps tSK(P) Skew of Opposite Transitions (7) of the Same Output RL=50Ω, CL=10pF Figure 6, Figure 12 3.0 to 3.6 20 ps RL=50Ω, CL=10pf, tR=tF=750ps at 480Mbps 15 (PRBS=2 – 1) 3.0 to 3.6 150 ps tJ (7) (7) Total Jitter Note: 7. Guaranteed by characterization. Capacitance Symbol Parameter Conditions TA=- 40ºC to +85ºC Min. Typ. Units Max. CIN Control Pin Input Capacitance VCC=0V Figure 11 2 pF CON D1n, D2n, Dn On Capacitance VCC=3.3V, /OE=0V Figure 10 9 pF COFF D1n, D2n Off Capacitance VCC and /OE=3.3V Figure 11 4 pF © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch USB Hi-Speed-Related AC Electrical Characteristics www.fairchildsemi.com 5 VON I D (OFF) n NC A D1n, D2n VIN Dn Select VIN I ON GND Select R ON = GND **Each switch port is tested separately VS = 0 to VCC VON / ION GND VS =0 or VCC Figure 4. On Resistance Figure 5. Off Leakage D1+, D1VIN CL GND RS tFALL=500ps tRISE=500ps D1+, D1- RL 800mV VOUT Input:Dn+, Dn- 90% 90% 50% GND 400mV V Sel 50% 10% VOH 10% 50% 50% GND FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Test Diagrams Output:D+, D- R L, RS , and C L are fun ctions of the app lication environment (see AC Tables for spec ific va lues) VOL tPLH tPHL C L includ es test fixture and stray capacitance. Figure 6. AC Test Circuit Load Figure 7. Switch Propagation Delay Waveforms tFALL=2.5ns tRISE=2.5ns Network Analyzer NC RS VCC Input - S, /OE 10% GND 90% 90% VCC/2 VCC/2 VOH GND V IN VS VSel 10% GND GND RT GND 90% 90% Output - VOUT GND RS and RT are functions of the application environment (50Ω, 75Ω or 100Ω). VOL tON tOFF Figure 8. Turn On / Turn Off Waveform © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 RT V OUT GND Crosstalk = 20 Log (VOUT / VIN) Figure 9. Non-Adjacent Channel-to-Channel Crosstalk www.fairchildsemi.com 6 Capacitance Meter Dn Dn S S Capacitance Meter VSel =0 or VCC f=1MHz D1n, D2n VSel = 0 or VCC f=1MHz Figure 10. Channel On Capacitance D1n, D2n Figure 11. Channel Off Capacitance tFALL=750ps tRISE=750ps 800mV 800mV 90% 400mV 50% 10% 50% 10% VOH 90% 50% 90% 50% 400mV Input:Dn+, Dn- 90% Input: D+, D- tFALL=750ps tRISE=750ps 50% tPLH1 50% 50% 50% Output 1: D+, D- 10% VOL VOH 10% tPHL1 Output:D+, D- VOL tPLH VOH tPHL 50% FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Test Diagrams (Continued) 50% Output 1: D2+, D2- TSK(P)= tPHL-tPLH Pulse Skew, TSK(P) VOL tPLH2 tPHL2 Figure 12. Switch Skew Tests Network Analyzer RS GND VSel VIN VS GND GND VOUT GND RSand RT are functions of the application environment (see AC tables for specific values). RT GND Figure 13. Bandwidth Network Analyzer RS VSel GND RT GND VIN VS GND GND VOUT GND RT Off Isolation =20Log(VOUT/VIN) GND Figure 14. Channel Off Isolation © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 7 FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Physical Dimensions Figure 15. 10-Lead MicroPak™ 1.6 x 2.1mm Note: click here for tape and reel specifcations, available at: http://www.fairchildsemi.com/products/analog/pdf//micropak_tr.pdf Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/ © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 8 FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch Physical Dimensions Figure 16. 16-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN) Package Note: click here for tape and reel specifcations, available at: http://www.fairchildsemi.com/products/analog/packaging/MLP16_25x35.html Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/ © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 9 FSUSB23 — High-Speed, USB2.0 (480Mbps) Switch © 2006 Fairchild Semiconductor Corporation FSUSB23 • Rev. 1.0.1 www.fairchildsemi.com 10