MAXIM MAX1856

19-1898; Rev 0; 2/01
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
The MAX1856 offers a low-cost solution for generating a
SLIC (ringer and off-hook) power supply. Using standard
off-the-shelf transformers from multiple vendors, the
MAX1856 generates various output voltages: -24V and
-72V (dual output) for both ringer and off-hook supplies for
voice-enabled broadband consumer premises equipment
(CPE), -48V for IP phones and routers, -5V and -15V (single or dual output) for DSL CO line drivers, or negative
voltages as high as -185V for MEMS bias supplies. The
output voltages are adjusted with an external voltage
divider.
Due to its wide operating voltage range, the MAX1856
operates from a low-cost, unregulated DC power supply
for cost-sensitive applications like xDSL, cable modems,
set-top boxes, LMDS, MMDS, WLL, and FTTH CPE. The
MAX1856 provides low audio-band noise for talk battery
and a sturdy output capable of handling the ring trip conditions for ring battery.
The operating frequency can be set between 100kHz and
500kHz with an external resistor in free-running mode. For
noise-sensitive applications, the MAX1856’s operating frequency can be synchronized to an external clock over its
operating frequency range.
The flyback topology allows operation close to 50% duty
cycle, offering high transformer utilization, low ripple current, and less stress on input and output capacitors.
Internal soft-start minimizes startup stress on the input
capacitor, without any external components.
The MAX1856’s current-mode control scheme does not
require external loop compensation. The low-side currentsense resistor provides accurate current-mode control
and overcurrent protection.
Applications
VoIP Ringer and Off-Hook Voltage Generators
Cable and DSL Modems
Set-Top Boxes
Wireless Local Loop
FTTH
LMDS/MMDS
Routers
Industrial Power Supplies
CO DSL Line Driver Supplies
MEMS Bias Supplies
Features
♦ Low-Cost, Off-the-Shelf Transformer
♦ 3V to 28V Input Range
♦ Low Audio-Band Noise on Talk Battery
♦ Effectively Handles Ring Trip Transients
♦ Powers 2-, 4-, or 12-Line Equipment
♦ High Efficiency Extends Battery Life During
Life-Line Support Conditions
♦ Adjustable 100kHz to 500kHz Switching
Frequency
♦ Clock Synchronization
♦ Internal Soft-Start
♦ Current-Mode PWM and Idle Mode™ Control
Scheme
♦ Logic-Level Shutdown
♦ 10-Pin µMAX Package
Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
MAX1856EUB
-40°C to +85°C
10 µMAX
Typical Operating Circuit
INPUT
3V TO 28V
OUT2
-72V
1
VCC
2
SYNC/SHDN
LDO
EXT
2
OUT1
-24V
CS
FREQ
MAX1856
2
GND
FB
PGND
REF
Idle Mode is a trademark of Maxim Integrated Products.
________________________________________________________________ Maxim Integrated Products
1
For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX1856
General Description
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
ABSOLUTE MAXIMUM RATINGS
Continuous Power Dissipation (TA = +70°C)
10-Pin µMAX (derate 5.6mW/°C above +70°C) ...........444mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
VCC, SYNC/SHDN to GND .....................................-0.3V to +30V
PGND to GND .......................................................-0.3V to +0.3V
LDO, FREQ, FB, CS to GND.....................................-0.3V to +6V
EXT, REF to GND......................................-0.3V to (VLDO + 0.3V)
LDO Output Current............................................-1mA to +20mA
LDO Short Circuit to GND ...............................................<100ms
REF Short Circuit to GND ...........................................Continuous
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = SYNC/SHDN, VCC = 5V, VLDO = 5V, ROSC = 200kΩ, TA = 0°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
3
28
V
2.7
5.5
V
50
nA
PWM CONTROLLER
Operating Input Voltage Range
VCC
FB Input Current
IFB
VCC = VLDO
VFB = -0.05V
1
Load Regulation
VCS = 0 to 100mV for 0 to ILOAD(MAX)
Line Regulation
Typically 0.0074% per % duty factor on EXT
Current-Limit Threshold
VCS
CS Input Current
ICS
85
Shutdown Supply Current
100
%/%
mV
1
µA
15
25
mV
VFB = -0.05V, VCC = 3V to 28V
250
400
µA
SYNC/SHDN = GND, VCC = 28V
3.5
6
µA
5.00
5.50
CS = GND
5
ICC
%/mV
115
Idle Mode Current-Sense
Threshold
VCC Supply Current (Note 1)
0.013
0.0074
REFERENCE AND LDO REGULATOR
5V ≤ VCC ≤ 28V
4.50
3V ≤ VCC ≤ 28V
2.65
V
LDO Output Voltage
VLDO
RLDO = 400Ω
Undervoltage Lockout
Threshold
VUVLO
VLDO falling edge, 1% hysteresis (typ)
2.40
2.50
2.60
RREF = 10kΩ, CREF = 0.22µF
1.225
1.250
1.275
V
-2
-10
mV
V
REF to FB Voltage (Note 2)
VREF
5.50
REF Load Regulation
IREF = 0 to 400µA
REF Undervoltage Lockout
Threshold
Rising edge, 1% hysteresis (typ)
1.0
1.1
1.2
ROSC = 100kΩ ±1%
425
500
575
ROSC = 200kΩ ±1%
225
250
275
ROSC = 500kΩ ±1%
85
100
115
ROSC = 100kΩ ±1%
86
90
94
ROSC = 200kΩ ±1%
87
90
93
ROSC = 500kΩ ±1%
86
90
94
V
OSCILLATOR
Oscillator Frequency
Maximum Duty Cycle
2
fOSC
D
_______________________________________________________________________________________
kHz
%
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
(VCC = SYNC/SHDN, VCC = 5V, VLDO = 5V, ROSC = 200kΩ, TA = 0°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Minimum EXT Pulse Width
290
Minimum SYNC Input Signal
Duty Cycle
20
45
%
Minimum SYNC Input
Low Pulse Width
50
200
ns
Maximum SYNC Input
Rise/Fall Time
200
SYNC Input Frequency Range
fSYNC
SYNC/SHDN Falling Edge to
Shutdown Delay
tSHDN
SYNC/SHDN Input High Voltage
VIH
SYNC/SHDN Input Low Voltage
VIL
SYNC/SHDN Input Current
EXT Sink/Source Current
EXT On-Resistance
100
ns
ns
500
50
kHz
µs
2.0
V
0.45
VSYNC/SHDN = 5V
0.5
3.0
VSYNC/SHDN = 28V
1.5
10
IEXT
EXT forced to 2V
1
RON(EXT)
EXT high or low
2
V
µA
A
5
Ω
MAX
UNITS
ELECTRICAL CHARACTERISTICS
(VCC = SYNC/SHDN, VCC = 5V, VLDO = 5V, ROSC = 200kΩ, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
PWM CONTROLLER
Operating Input Voltage Range
VCC
FB Input Current
IFB
Current-Limit Threshold
VCS
CS Input Current
ICS
VCC Supply Current (Note 1)
ICC
Shutdown Supply Current
VCC = VLDO
3
28
V
2.7
5.5
V
50
nA
85
115
mV
1
µA
VFB = -0.05V
CS = GND
VFB = -0.05V, VCC = 3V to 28V
SYNC/SHDN = GND, VCC = 28V
400
µA
6
µA
REFERENCE AND LDO REGULATOR
5V ≤ VCC ≤ 28V
4.50
5.50
3V ≤ VCC ≤ 28V
2.65
5.50
1.22
1.28
V
-10
mV
V
LDO Output Voltage
VLDO
RLDO = 400Ω
REF to FB Voltage (Note 2)
VREF
RREF = 10kΩ, CREF = 0.22µF
REF Load Regulation
IREF = 0 to 400µA
REF Undervoltage Lockout
Threshold
Rising edge, 1% hysteresis (typ)
1.0
1.2
ROSC = 100kΩ ±1%
425
575
ROSC = 200kΩ ±1%
222
278
ROSC = 500kΩ ±1%
85
115
V
OSCILLATOR
Oscillator Frequency
fOSC
kHz
_______________________________________________________________________________________
3
MAX1856
ELECTRICAL CHARACTERISTICS (continued)
ELECTRICAL CHARACTERISTICS (continued)
(VCC = SYNC/SHDN, VCC = 5V, VLDO = 5V, ROSC = 200kΩ, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
Maximum Duty Cycle
D
CONDITIONS
MIN
TYP
MAX
ROSC = 100kΩ ±1%
86
94
ROSC = 200kΩ ±1%
87
93
ROSC = 500kΩ ±1%
86
94
UNITS
%
Minimum SYNC Input Signal
Duty Cycle
45
%
Minimum SYNC Input
Low Pulse Width
200
ns
500
kHz
SYNC Input Frequency Range
fSYNC
100
SYNC/SHDN Input High Voltage
VIH
2.0
SYNC/SHDN Input Low Voltage
VIL
EXT On-Resistance
V
0.45
SYNC/SHDN Input Current
RON(EXT)
VSYNC/SHDN = 5V
3.0
VSYNC/SHDN = 28V
10
EXT high or low
5
V
µA
Ω
Note 1: This is the VCC current consumed when active, but not switching, so the gate-drive current is not included.
Note 2: The reference output voltage (VREF) is measured with respect to FB. The difference between REF and FB is guaranteed to
be within these limits to ensure output voltage accuracy.
Note 3: Specifications to -40°C are guaranteed by design, not production tested.
Typical Operating Characteristics
(Circuit of Figure 1, VCC = VSYNC/SHDN = 12V, VOUT1 = -24V, VOUT2 = -72V, ROSC = 200kΩ, unless otherwise noted.)
-72V CROSS-REGULATION VOLTAGE
vs. LOAD CURRENT
-22.5
100
MAX1856 toc02
-72.0
MAX1856 toc01
-22.0
EFFICIENCY vs. LOAD CURRENT
(-24V OUTPUT)
-72.5
90
-23.5
VIN = 12V
-24.0
VIN = 24V
VOUT1 = -24V
VOUT2 = -72V
IOUT2 = 5mA
-24.5
VIN = 12V
VIN = 24V
-73.5
VIN = 5V
-74.0
VOUT1 = -24V
VOUT2 = -72V
IOUT2 = 5mA
100
200
300
400
IOUT1 (mA)
500
600
700
80
VIN = 24V
70
VOUT1 = -24V
VOUT2 = -72V
IOUT2 = 5mA
60
50
-74.5
0
4
-73.0
EFFICIENCY (%)
VOUT2 (V)
-23.0
VIN = 12V
VIN = 5V
VIN = 5V
MAX1856 toc03
-24V OUTPUT VOLTAGE
vs. LOAD CURRENT
VOUT1 (V)
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
0
100
200
300
400
IOUT1 (mA)
500
600
700
0
100
200
300
400
IOUT1 (mA)
_______________________________________________________________________________________
500
600
700
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
-23.2
-23.6
-73
-23.8
VOUT1 = -24V
VOUT2 = -72V
IOUT1 = 5mA
-74
-24.0
50
100
150
200
50
0
50
100
150
200
150
200
DUAL-OUTPUT EFFICIENCY
vs. INPUT VOLTAGE
VOUT1 (V)
-71.8
VOUT1 = -24V
IOUT1 = 50mA
VOUT2 = -72V
IOUT2 = 50mA
VOUT1 = -24V
IOUT1 = 50mA
VOUT2 = -72V
IOUT2 = 50mA
-72.6
-24.0
10
15
20
25
80
VOUT1 = -24V
IOUT1 = 50mA
VOUT2 = -72V
IOUT2 = 50mA
70
60
-73.0
5
50
0
5
10
15
20
25
0
5
10
15
20
VIN (V)
VIN (V)
VIN (V)
-48V OUTPUT VOLTAGE
vs. LOAD CURRENT
EFFICIENCY vs. LOAD CURRENT
(-48V OUTPUT)
SUPPLY CURRENT
vs. INPUT VOLTAGE
90
VIN = 12V
EFFICIENCY (%)
VIN = 5V
-47.3
VIN = 24V
-47.7
-48.1
80
70
VIN = 24V
200
IOUT2 (mA)
300
400
150
100
CURRENT INTO VCC PIN
ROSC = 500kΩ
VOUT = -48V
FIGURE 4
0
50
100
200
50
60
VOUT = -48V
FIGURE 4
-48.5
MAX1856 toc12
VIN = 5V
25
250
SUPPLY CURRENT (µA)
VIN = 12V
MAX1856 toc11
100
MAX1856 toc10
-46.5
250
VOUT1 = -24V
IOUT1 = 100mA
VOUT2 = -72V
IOUT2 = 100mA
90
EFFICIENCY (%)
VOUT1 = -24V
IOUT1 = 100mA
VOUT2 = -72V
IOUT2 = 100mA
-71.4
100
MAX1856 toc08
-71.0
-72.2
0
100
-72V OUTPUT VOLTAGE
vs. INPUT VOLTAGE
-23.4
-46.9
50
-24V OUTPUT VOLTAGE
vs. INPUT VOLTAGE
-23.6
VOUT2 (V)
0
250
IOUT2 (mA)
-23.2
0
VOUT1 = -24V
VOUT2 = -72V
IOUT1 = 5mA
IOUT2 (mA)
VOUT1 = -24V
IOUT1 = 100mA
VOUT2 = -72V
IOUT2 = 100mA
-23.8
VIN = 24V
70
IOUT2 (mA)
-23.0
VOUT1 (V)
250
MAX1856 toc07
0
80
60
VOUT1 = -24V
VOUT2 = -72V
IOUT1 = 5mA
VIN = 24V
VIN = 5V
MAX1856 toc09
VIN = 24V
VIN = 12V
VIN = 5V
-23.4
VIN = 12V
90
EFFICIENCY (%)
-72
100
MAX1856 toc05
VIN = 12V
VIN = 5V
VOUT1 (V)
VOUT2 (V)
-71
EFFICIENCY vs. LOAD CURRENT
(-72V OUTPUT)
-23.0
MAX1856 toc04
-70
-24V CROSS-REGULATION VOLTAGE
vs. LOAD CURRENT
MAX1856 toc06
-72V OUTPUT VOLTAGE
vs. LOAD CURRENT
0
100
200
IOUT2 (mA)
300
400
0
5
10
15
20
25
30
INPUT VOLTAGE (V)
_______________________________________________________________________________________
5
MAX1856
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VCC = VSYNC/SHDN = 12V, VOUT1 = -24V, VOUT2 = -72V, ROSC = 200kΩ, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VCC = VSYNC/SHDN = 12V, VOUT1 = -24V, VOUT2 = -72V, ROSC = 200kΩ, unless otherwise noted.)
2.5
2.0
1.5
100
50
CURRENT INTO VCC PIN
ROSC = 500kΩ
SYNC/SHDN = GND
0.5
CURRENT INTO VCC PIN
0
-15
10
35
60
0
0
85
5
10
15
20
25
TEMPERATURE (°C)
INPUT VOLTAGE (V)
REFERENCE VOLTAGE
vs. REFERENCE CURRENT
REFERENCE VOLTAGE
vs. TEMPERATURE
MAX1856 toc16
1.260
1.260
NO LOAD
1.250
1.245
1.245
1.240
1.240
0
100
200
300
500
400
6
1000
-15
10
35
60
85
100
SWITCHING FREQUENCY
vs. TEMPERATURE
EXT RISE/FALL TIME
vs. CAPACITANCE
70
MAX1856 toc19
600
ROSC = 100kΩ
60
EXT RISE/FALL TIME (ns)
500
400
ROSC = 200kΩ
200
tRISE, VIN = 5V
50
tRISE, VIN = 3.3V
40
tFALL, VIN = 5V
30
tFALL, VIN = 3.3V
20
ROSC = 500kΩ
100
10
0
0
-40
-15
10
35
TEMPERATURE (°C)
8
10
1000
ROSC (kΩ)
TEMPERATURE (°C)
300
4
100
-40
REFERENCE CURRENT (µA)
SWITCHING FREQUENCY (kHz)
2
SWITCHING FREQUENCY vs. ROSC
1.255
1.250
0
ILDO (mA)
VREF (V)
1.255
30
MAX1856 toc17
-40
SWITCHING FREQUENCY (kHz)
150
MAX1856 toc15
150
1.0
190
6
VIN = 5V
MAX1856 toc18
ROSC = 500kΩ
3.0
VIN = 3.3V
200
MAX1856 toc20
230
3.5
DROPOUT VOLTAGE (V)
ROSC = 200kΩ
270
250
MAX1856 toc14
ROSC = 100kΩ
4.0
SHUTDOWN CURRENT (µA)
SUPPLY CURRENT (µA)
MAX1856 toc13
350
310
LDO DROPOUT VOLTAGE
vs. LOAD CURRENT
SHUTDOWN CURRENT
vs. INPUT VOLTAGE
SUPPLY CURRENT
vs. TEMPERATURE
VREF (V)
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
60
85
0.1
1
10
CAPACITANCE (nF)
_______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
ENTERING SHUTDOWN
EXITING SHUTDOWN
HEAVY-LOAD SWITCHING WAVEFORM
MAX1856 toc22
MAX1856 toc21
MAX1856 toc23
-47.0V
5V
5V
A
A
0
0
2A
A
-47.1V
5V
B
B
0
0
-47.2V
0
4A
-20V
2A
C
C
0
-40V
B
2A
0
-60V
10µs/div
A. VSYNC/SHDN = 5V TO 0, 5V/div
B. VEXT, 5V/div
C. ILP, 2A/div
VOUT = -48V, ROUT = 240Ω
CIRCUIT OF FIGURE 4
4ms/div
A. VSYNC/SHDN = 0 TO 5V, 5V/div
B. ILP, 2A/div
C. VOUT = -48V, ROUT = 2.4kΩ, 20V/div
CIRCUIT OF FIGURE 4
LIGHT-LOAD SWITCHING WAVEFORM
LOAD TRANSIENT
MAX1856 toc24
-47.72V
2.0µs/div
A. VOUT = -48V, IOUT = 200mA, 50mV/div
B. ILP, 2A/div
CIRCUIT OF FIGURE 4
LINE TRANSIENT
MAX1856 toc25
MAX1856 toc26
200mA
14V
A
A
-47.76V
0
12V
-47.1V
10V
B
-47.6V
-47.80V
A
-48.1V
B
B
2A
C
-47V
0
1ms/div
A. IOUT = 20mA TO 200mA, 200mA/div
B. VOUT, = -48V, 500mV/div
C. ILP, 2A/div
CIRCUIT OF FIGURE 4
4µs/div
A. VOUT = -48V, IOUT = 20mA, 20mV/div
B. ILP, 2A/div
CIRCUIT OF FIGURE 4
400µs/div
A. VIN = 10V TO 14V, 2Vdiv
B. VOUT = -48V, IOUT = 200mA, 100mV/div
CIRCUIT OF FIGURE 4
RINGER TO TALK-BATTERY CROSSTALK
MAX1856 toc27
60
RINGER OUTPUT
40
20
(dB)
0
TALK-BATTERY OUTPUT
-20
-40
-60
-80
-100
0
50
100
150
200
250
FREQUENCY (Hz)
_______________________________________________________________________________________
7
MAX1856
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VCC = VSYNC/SHDN = 12V, VOUT1 = -24V, VOUT2 = -72V, ROSC = 200kΩ, unless otherwise noted.)
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
MAX1856
Pin Description
PIN
NAME
1
LDO
5V Linear Regulator Output. The regulator powers all of the internal circuitry, including the EXT gate
driver. Bypass LDO to GND with a 1µF or greater ceramic capacitor.
2
FREQ
Oscillator Frequency Set Input. A resistor from FREQ to GND sets the oscillator from 100kHz (ROSC =
500kΩ) to 500kHz (ROSC = 100kΩ): fOSC = 50MΩ-kHz / ROSC. The MAX1856 still requires ROSC when
an external clock is connected to SYNC/SHDN.
3
GND
Analog Ground
4
REF
1.25V Reference Output. REF can source up to 400µA. Bypass to GND with a 2.2µF ceramic capacitor.
5
FB
Feedback Input. The feedback voltage threshold is 0.
6
CS
Positive Current-Sense Input. Connect a current-sense resistor (RCS) between CS and PGND.
7
PGND
8
EXT
External MOSFET Gate-Driver Output. EXT swings from LDO to PGND.
9
VCC
Input Supply to the Linear Regulator. VCC accepts inputs up to 28V. Bypass to PGND with a 1µF
ceramic capacitor.
10
SYNC/SHDN
FUNCTION
Power Ground
Shutdown Control and Synchronization Input. There are three operating modes:
• SYNC/SHDN low: shutdown mode
• SYNC/SHDN high: the DC-to-DC controller operates with the oscillator frequency set at FREQ by
ROSC
• SYNC/SHDN clocked: the DC-to-DC controller operates with the oscillator frequency set by the SYNC
clock input. The conversion cycles initiate on the rising edge of the input clock signal. However, the
MAX1856 still requires ROSC when SYNC/SHDN is externally clocked.
Detailed Description
The MAX1856 current-mode PWM controller uses an
inverting flyback configuration that is ideal for generating the high negative voltages required for SLIC power
supplies. Optimum conversion efficiency is maintained
over a wide range of loads by employing both PWM
operation and Maxim’s proprietary Idle Mode control to
minimize operating current at light loads. Other features
include shutdown, adjustable internal operating frequency or synchronization to an external clock, softstart, adjustable current limit, and a wide (3V to 28V)
input range.
PWM Controller
The heart of the MAX1856 current-mode PWM controller is a BiCMOS multi-input comparator that simultaneously processes the output-error signal, the
current-sense signal, and a slope-compensation ramp
(Figure 2). The main PWM comparator is direct summing, lacking a traditional error amplifier and its associ8
ated phase shift. The direct-summing configuration
approaches ideal cycle-by-cycle control over the output voltage since there is no conventional error amplifier in the feedback path.
In PWM mode, the controller uses fixed-frequency, current-mode operation where the duty ratio is set by the
input-to-output voltage ratio and the transformer’s turn
ratio. The current-mode feedback loop regulates peak
inductor current as a function of the output error signal.
At light loads, the controller enters Idle Mode. During
Idle Mode, switching pulses are provided only as necessary to supply the load, and operating current is minimized to provide the best light-load efficiency. The
minimum-current comparator threshold is 15mV, or
15% of the full-load value (IMAX) of 100mV. When the
controller is synchronized to an external clock, Idle
Mode occurs only at very light loads.
_______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
T1
CIN
(2x) 10µF
25V
R5
10Ω
9
10
1
VCC
C3
100pF
MAX1856
1
LDO
EXT
CS
8
RCS
33mΩ
FB
CFB
1nF
R3
5.11kΩ
REF
R1
174kΩ
C1
330µF
Sanyo
35MV330AX
5
3 GND
PGND
2
R2
681kΩ
FREQ
ROSC
200kΩ
OUT1
-24V
D1
C5
1nF
7
2
M1
R6
100Ω
6
CLDO
1µF
2
C2
100µF
Sanyo
100MV100AX
R4
470Ω
SYNC/SHDN
C4
1µF
OUT2
-72V
D2
2
MAX1856
*INPUT
4.5V TO 24V
4
D1, D2: Central Semiconductor CMR1U-02
M1: International Rectifier IRLL2705
T1: Coiltronics CTX01-14853
CREF
2.2µF
*INPUT RANGE LIMITED BY OUTPUT POWER REQUIREMENTS.
SEE MAXIMUM OUTPUT POWER AND TYPICAL OPERATING CHARACTERISTICS.
Figure 1. Standard Application Circuit
Low-Dropout Regulator (LDO)
All MAX1856 functions, including EXT, are internally
powered from the on-chip, low-dropout 5V regulator.
The regulator input is at VCC, while its output is at LDO.
The VCC-to-LDO dropout voltage is typically 200mV
(300mV max at 12mA), so that when V CC is <5.2V,
VLDO is typically VCC - 200mV. When the LDO is in
dropout, the MAX1856 still operates with VCC as low as
3V (as long as the LDO exceeds 2.7V), but with
reduced amplitude FET drive at EXT. The maximum
VCC input voltage is 28V.
LDO can supply up to 12mA to power the IC, supply
gate charge through EXT to the external FET, and supply small external loads. When driving particularly large
FETs at high switching rates, little or no LDO current
may be available for external loads. For example, when
switched at 500kHz, a large FET with 20nC gate charge
requires 20nC ✕ 500kHz, or 10mA.
Soft-Start
The MAX1856 features a “digital” soft-start that is preset and requires no external capacitor. Upon startup,
the peak inductor current increments from 1/5th of the
value set by RCS, to the full current-limit value in five
steps over 1024 cycles of fOSC or fSYNC. Additionally,
the oscillator runs at 1/3 the normal operating frequency (fOSC/3) until the output voltage reaches 20% of its
nominal value (VFB ≤ 1.0V). See the Typical Operating
Characteristics for a scope picture of the soft-start
operation. Soft-start is implemented: 1) when power is
first applied to the IC, 2) when exiting shutdown with
power already applied, and 3) when exiting undervoltage lockout. The MAX1856’s soft-start sequence does
not start until VLDO reaches 2.5V.
Design Procedure
The MAX1856 can operate within a wide input voltage
range from 3V to 28V. This allows it to be used with wall
adapters. In applications driven by low-power, low-cost
and low input and output ripple current requirements,
the MAX1856 flyback topology can be used to generate various levels of output voltages and multiple outputs.
Communications over the Internet interface with a standard telephone connection, which includes the
Subscriber Line Interface Circuit (SLIC). The SLIC
requires a negative power supply for the audio and
ringer functions. The circuits discussed here are
designed for these applications. The following design
discussions are related to the standard application cir-
_______________________________________________________________________________________
9
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
9 VCC
MUX
0
ANTISAT
LDO
1
EXT
8
PGND
7
FREQ
2
1
R1
552kΩ
R3
276kΩ
4
R2
276kΩ
R
Q
S
REF
VREF
1.25V
5
MUX
FB
1
SLOPE COMP
0
X6
1.0V
X1
6
CS
FOSC
X1
FOSC/3
3 GND
IMAX
BIAS
100mV
10
MAX1856
IMIN
SYNC/SHDN
15mV
Figure 2. Functional Diagram
cuit (Figure 1) converting a +12V input to a -72V output
(maximum load 100mA) and a -24V output (maximum
load 400mA).
Maximum Output Power
The maximum output power the MAX1856 can provide
depends on the maximum input power available and
the circuit’s efficiency:
POUT(MAX) = EFFICIENCY × PIN(MAX)
Furthermore, the efficiency and input power are both
functions of component selection. Efficiency losses can
be divided into three categories: 1) resistive losses
across the transformer, MOSFET’s on-resistance, current-sense resistor, and the ESR of the input and output
capacitors; 2) switching losses due to the MOSFET’s
transition region, the snubber circuit, which also
increases the transition times, and charging the MOSFET’s gate capacitance; and 3) transformer core loss10
es. Typically, 80% efficiency can be assumed for initial
calculations. The input power depends on the current
limit, input voltage, output voltage, inductor value, the
transformer’s turns ratio, and the switching frequency:
V
VIND 
PIN(MAX) = VIND  CS −

 RCS 2ƒ OSCL 
NPVOUT
D=
NPVOUT + NSVIN
where NP:NS is the transformer’s turns ratio.
Setting the Operating Frequency
(SYNC/SHDN and FREQ)
The SYNC/SHDN pin provides both external-clock synchronization (if desired) and shutdown control. When
SYNC/SHDN is low, all IC functions are shut down. A
logic high at SYNC/SHDN selects operation at a
______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
ROSC =
50MΩ × kHz
ƒ OSC (kHz)
Thus, a 250kHz operating frequency, for example, is
set with R OSC = 200kΩ. At higher frequencies, the
magnetic components will be smaller. Peak currents
and, consequently, resistive losses will be lower at the
higher switching frequency. However, core losses, gate
charge currents, and switching losses increase with
higher switching frequencies.
Rising clock edges on SYNC/SHDN are interpreted as
synchronization input. If the sync signal is lost while
SYNC/SHDN is high, the internal oscillator takes over at
the end of the last cycle, and the frequency is returned
to the rate set by R OSC . If the signal is lost with
SYNC/SHDN low, the IC waits for 50µs before shutting
down. This maintains output regulation even with intermittent sync signals. When an external sync signal is
used, Idle Mode switchover at the 15mV current-sense
threshold is disabled so that Idle Mode only occurs at
very light loads. Also, ROSC should be set for a frequency 15% below the SYNC clock rate:
50MΩ × kHz
ROSC(SYNC) =
0.85 ƒ OSC (kHz)
Setting the Output Voltage
Set the output voltage using two external resistors forming a resistive divider to FB between the output and
REF. First select a value for R3 between 3.3kΩ and
100kΩ. R1 is then given by:
V

R1 = R3  OUT 
 VREF 
For a dual output as shown in Figure 1, a split feedback
technique is recommended. Since the feedback voltage threshold is 0, the total feedback current is:
V
ITOTAL = IR1 + IR2 = REF
R3
Since the feedback resistors are connected to the reference, ITOTAL must be <400µA so that VREF is guaranteed to be in regulation (see Electrical Characteristics
Table). Therefore, select R3 so the total current value is
between 200µA and 250µA as shown in Figure 1. To
ensure that the MAX1856 regulates both outputs with
the same degree of accuracy over load, select the
feedback resistors (R1 and R2) so their current ratio
(IR1:IR2) equals the output power ratio (POUT1:POUT2)
under full load:
IR1 VOUT1IOUT1
=
IR2 VOUT2 IOUT2
Once R3 and the dual feedback currents (IR1 and IR2)
are determined from the two equations above, use the
following two equations to determine R1 and R2:
V
V
IR1 = OUT1 and IR2 = OUT2
R1
R2
Selecting the Transformer
The MAX1856 PWM controller works with economical
off-the-shelf transformers. The transformer selection
depends on the input-to-output voltage ratio, output
current capacity, duty cycle, and oscillator frequency.
Table 1 shows recommended transformers for the typical applications, and Table 2 gives some recommended suppliers.
Transformer Turns Ratio
The transformer turns ratio is a function of the input-tooutput voltage ratio and maximum duty cycle. Under
steady-state conditions, the change in flux density during the on-time must equal the return change in flux
density during the off-time (or flyback period):
VINt ON VOUT t OFF
=
NP
NS
For example, selecting a 50% duty cycle for the standard application circuit (Figure 1) and a +12V input
voltage, the -72V output requires a 1:6 turns ratio, and
the -24V output requires a 1:2 turns ratio. Therefore, a
transformer with a 1:2:2:2 turns ratio was selected.
Primary inductance
The average input current at maximum load can be calculated as:
IIN(DC) =
VOUT IOUT(MAX)
ηVIN(MIN)
where η = efficiency. For VOUT = -24V, IOUT(MAX) =
400mA, and VIN(MIN) = 10.8V as shown in Figure 1, this
______________________________________________________________________________________
11
MAX1856
100kHz to 500kHz frequency, which is set by a resistor
(ROSC) connected from FREQ to GND. The relationship
between fOSC and ROSC is:
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
Table 1. Transformer Selection for Standard Applications
INPUT VOLTS (V)
OUTPUT VOLTS (V)
OUTPUT CURRENT (mA)
TRANSFORMER (VENDOR)
5
-48
100
VP3-0055 (Coiltronics)
12
-48
100
CTX01-14853 (Coiltronics), or
ICA-0635 (ICE Components)
12
-24 and -72
400 or 100
CTX01-14853 (Coiltronics), or
ICA-0635 (ICE Components)
12
-95 and -30
320 and 150
CTX03-15220 (Coiltronics)
Table 2. Transformer Suppliers
VENDOR
USA PHONE
USA FAX
INTERNET
Coilcraft
847-639-6400
847-639-1469
www.coilcraft.com
Coiltronics
888-414-2645
561-241-9339
www.coiltronics.com
ICE Components
800-729-2099
703-257-7547
www.icecomponents.com
Pulse Engineering
858-674-8100
858-674-8262
www.pulseeng.com
TDK
847-390-4461
847-390-4405
www.tdk.com
gives 1.11A for 80% efficiency. With a duty cycle of
52.5%, the average switch current (ISW(AVG)) is 2.114A.
Choosing a primary inductance ripple current ∆IL to be
40% of the average switch current, the primary inductance is given by:
For the standard application circuit (fOSC = 250kHz),
the EFD15 core from Coiltronics meets the criteria.
Once the core is chosen, the number of turns in the primary is given by:
NP =
VIND
LP =
∆IL ƒ OSC
Selecting fOSC = 250kHz and ∆IL = 0.4 x ISW(AVG) =
0.846A, the primary inductance value is 27µH, and the
peak primary current for this example is therefore 2.5A.
Core Selection
The transformer in a flyback converter is a coupled
inductor with multiple windings on the same magnetic
core. Flyback topologies operate by storing energy in
the transformer magnetics during the on-time and
transferring this energy to the output during the offtime.
Core selection depends on the core’s power-handling
capability. The required output power is first considered. For example, the standard application circuit
requires 9.6W. Assuming a typical 80% efficiency, the
transformer must support 12W of power. The core
material’s properties, the core’s shape, and the size of
the air gap determine the core’s power rating. Since the
equations relating these properties to the power capability are involved, manufacturers simply provide charts
giving “Power vs. Frequency” for different core sizes.
12
LP
AL
where AL is the inductance factor. Ensure that the number of ampere-turns (NPISAT) is below the saturation
limit. A significant portion of the total energy is stored in
the air gap. Therefore, the larger the air gap, the lower
the AL value and the larger the number of ampere-turns
at which saturation starts. Some manufacturers define
saturation as the current at which the inductance
decreases by 30%.
Current-Sense Resistor Selection
Once the peak inductor current is determined, the current-sense resistor (RCS) is determined by:
RCS =
VCS(MIN)
ILPEAK
= 85mV / ILPEAK
Kelvin-sensing should be used to connect CS and
PGND to RCS. Connect PGND and GND together at the
ground side of RCS.
Due to inductive ringing after the MOSFET turns on, a
lowpass filter may be required between RCS and CS to
prevent the noise from tripping the current-sense comparator. Connect a 100Ω resistor between CS and the
______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
Power MOSFET Selection
The MAX1856 drives a wide variety of N-channel power
MOSFETs (NFETs). Since the LDO limits the EXT output
gate drive to no more than 5V, a logic-level NFET is
required. Best performance, especially with input voltages below 5V, is achieved with low-threshold NFETs
that specify on-resistance with a gate-to-source voltage
(VGS) of 2.7V or less. When selecting an NFET, key
parameters include:
1) Total gate charge (QG)
2) Reverse transfer capacitance or charge (CRSS)
3) On-resistance (RDS(ON))
current, using the diode manufacturer’s data or approximating it with the following formula:

 ∆I
V
ID(PK) = IOUT 1+ OUT  + L
×
N
V

IN  2N
where N = N s/N P is the secondary-to-primary turns
ratio. Additionally, the diode’s reverse breakdown voltage must exceed VOUT plus the reflected input voltage
plus the leakage inductance spike. For high output voltages (50V or above), Schottky diodes may not be practical because of this voltage requirement. In these
cases, use a faster ultra-fast recovery diode with adequate reverse-breakdown voltage.
Capacitor Selection
4) Maximum drain-to-source voltage (VDS(MAX))
5) Minimum threshold voltage (VTH(MIN))
At high switching rates, dynamic characteristics (parameters 1 and 2 above) that predict switching losses
may have more impact on efficiency than R DS(ON),
which predicts DC losses. QG includes all capacitance
associated with charging the gate. In addition, this
parameter helps predict the current needed to drive the
gate at the selected operating frequency. The continuous LDO current for the FET gate is:
IGATE = QG × ƒ OSC
For example, the IRLL2705 has a typical QG of 17nC
(at VGS = 5V); therefore, the IGATE current at 500kHz is
8.5mA.
The switching element in a flyback converter must have
a high enough voltage rating to handle the input voltage plus the reflected secondary voltage, as well as
any spikes induced by leakage inductance. The reflected secondary voltage is given by:
N
VREFLECT = P (VOUT + VDIODE )
NS
where VDIODE is the voltage drop across the output
diode. For a 10% variation in input voltage and a 30%
safety margin, this gives a required 33V voltage rating
(V DS ) for the switching MOSFET in Figure 1. The
IRLL2705 with a VDS of 55V was chosen.
Diode Selection
The MAX1856’s high switching frequency demands a
high-speed rectifier. Schottky diodes are recommended for most applications because of their fast recovery
time and low forward voltage. Ensure that the diode’s
average current rating exceeds the peak secondary
Output Filter Capacitor
The output capacitor (COUT) does all the filtering in a flyback converter. Typically, COUT must be chosen based
on the output ripple requirement. The output ripple is
due to the variations in the charge stored in the output
capacitor with each pulse and the voltage drop across
the capacitor’s equivalent series resistance (ESR)
caused by the current into and out of the capacitor. The
ESR-induced ripple usually dominates, so output capacitor selection is actually based upon the capacitor’s
ESR, voltage rating, and ripple current rating.
Input Filter Capacitor
The input capacitor (CIN) in flyback designs reduces
the current peaks drawn from the input supply and
reduces noise injection. The value of C IN is largely
determined by the source impedance of the input supply. High source impedance requires high input capacitance, particularly as the input voltage falls. Since
inverting flyback converters act as “constant-power”
loads to their input supply, input current rises as the
input voltage falls. Consequently, in low-input-voltage
designs, increasing CIN and/or lowering its ESR can
add as much as 5% to the conversion efficiency.
Bypass Capacitors
In addition to CIN and COUT, three ceramic bypass
capacitors are also required with the MAX1856. Bypass
REF to GND with 2.2µF or more. Bypass LDO to GND
with 1µF or more. And bypass VCC to GND with 1µF or
more. All bypass capacitors should be located as close
to their respective pins as possible.
Compensation Capacitor
Output ripple voltage due to COUT ESR affects loop
stability by introducing a left half-plane zero. A small
capacitor connected from FB to GND forms a pole with
______________________________________________________________________________________
13
MAX1856
high side of R CS, and connect a 1000pF capacitor
between CS and GND.
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
the feedback resistance that cancels the ESR zero. The
optimum compensation value is:
CFB =


1
ESRCOUT
COUT 

×
+
2
(
R
1
R
3
)
/(
R
1
R
3
)


where R1 and R3 are feedback resistors (Figure 3). If
the calculated value for CFB results in a nonstandard
capacitance value, values from 0.5CFB to 1.5CFB will
also provide sufficient compensation.
Snubber Design
The MAX1856 uses a current-mode controller that
employs a current-sense resistor. Immediately after
turn-on, the MAX1856 uses a 100ns current-sense
blanking period to minimize noise sensitivity. However,
when the MOSFET turns on, the secondary inductance
and the output diode’s parasitic capacitance form a
resonant circuit that causes ringing. Reflected back
through the transformer to the primary side, these oscillations appear across the current-sense resistor and
last well beyond the 100ns blanking period. As shown
in Figure 1, a series RC snubber circuit at the output
diode increases the damping factor, allowing the ringing to settle quickly. Applications with dual output voltages require only one snubber circuit on the higher
voltage output.
The diode’s parasitic capacitance can be estimated
using the diode’s reverse voltage rating (VRRM), current
capability (I O ), and recovery time (t RR ). A rough
approximation is:
I t
CDIODE = O RR
VRRM
For the CMR1U-02 Central Semiconductor diode used
in Figure 1, the capacitance is roughly 172pF. A value
less than this (100pF) was chosen since the output
snubber only needs to dampen the ringing, so the initial
turn-on spike that occurs during the 100ns blanking
period is still present. Larger capacitance values
require more charge, thereby increasing the power dissipation.
The snubber’s time constant (tSNUB) must be smaller
than the 100ns blanking time. A typical RC time constant of 50ns was chosen for Figure 1:
50ns
t
R4 = SNUB =
C3
C3
When a MOSFET with a transformer load is turned off,
the drain will fly to a high voltage as a result of the energy stored in the transformer’s leakage inductance.
14
During the switch on-time, current is established in the
leakage inductance (LL) equal to the peak primary current (IPEAK). The energy stored in the leakage inductance is:
2
L I
EL = L PEAK
2
When the switch turns off, this energy is transferred to
the MOSFET’s parasitic capacitance, causing a voltage
spike at the MOSFET’s drain. For the IRLL2705 MOSFET, the capacitance value (CDS) is 130pF. If all of the
leakage inductance energy transfers to this capacitance, the drain would fly up to:
VCOSS =
LLIPEAK 2
CDS
The leakage inductance is (worst case) 1% of the primary inductance value. For a 0.27µH leakage inductance and a 2.5A peak current, the voltage reaches
114V at the MOSFET’s drain, which is much higher than
the MOSFET’s rated breakdown voltage. This causes
the parasitic bipolar transistor to turn on if the dv/dt at
the drain is high enough. Note that the inductive spike
adds on to the sum of the input voltage and the reflected secondary voltage already present at the drain of
the transistor (see Power MOSFET Selection).
A series combination RC snubber (R7 and C6 in Figure
3) across the MOSFET (drain to source) reduces this
spike. The energy stored in the leakage inductance
transfers to the snubber capacitor (C6) as electrostatic
energy. Therefore, C6 must be large enough to guarantee the voltage spike will not exceed the breakdown
voltage, but not so large as to result in excessive power
dissipation:
2
L I
C6 = L PEAK
2
VC6
Typically, a 30% safety margin is chosen so that VC6 is
at most equal to about 70% of the MOSFET’s VDS rating. For example, the VDSS is 55V for the IRLL2705, so
this gives a value of 1000pF for C9. The amount of
energy stored in snubber capacitor C6 has to discharge through series resistor R7 in the snubber network. During turn-off, the drain voltage rises in a time
period (tf) characteristic of the MOSFET used, which is
22ns for the IRLL2705. The RC time constant should
therefore equal this time. Hence:
______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
T1
CIN
D1
MAX1856
INPUT
3V TO 28V
OUTPUT
R5
9
10
C1
VCC
R4
SYNC/SHDN
C3
C4
MAX1856
M1
8
EXT
1
LDO
CS
R7
R6
6
CLDO
C6
C5
RCS
2 FREQ
ROSC
FB
5
3 GND
7
PGND
CFB
R3
REF
R1
4
CREF
Figure 3. Feedback Compensation and Snubber Circuits
R7 =
SLIC Power Supply with Split Feedback
tƒ
C6
This gives a value of about 22Ω for R7. However, this
snubber adds capacity to the MOSFET output, and this
in turn increases the dissipation in the MOSFET during
turn-on.
The selection of the input and output snubbers is an
interactive process. The design procedures above provide initial component recommendations, but the actual
values depend on the layout and transformer winding
practices used in the actual application.
Applications Information
Voice-over-IP CPE systems have +5V or +12V available
from which the talk battery voltage and the ringer voltage must be generated. The examples given below are
circuits using these supply voltages to generate the
negative power supplies needed in such applications.
Low Input Voltage
Telephones in broadband systems use low-power-consuming SLICs that reduce the power drain by providing
the option of using two voltages for loop supervision.
The load on each output is dependent on the number
of lines on- or off-hook. The higher voltage is used to
generate ring battery voltage when the subscriber is onhook, while a second lower voltage is used to generate
talk battery voltage when off-hook is detected. The actual value of these two voltages can be adjusted based on
system requirements and the specific SLIC used. The
design given here specifically addresses the supply
requirements for the AMD79R79 SLIC device with onchip ringing. The input voltage is 12V nominal, and the
output voltages are -24V at 400mA and -72V at 100mA.
The transformer turns ratio is 1:2:2:2, where 24V appears
across each secondary winding. The -72V output is
derived from the -24V output by stacking the secondary
windings in series as shown in Figure 1. A split feedback
is used, using resistors R1, R2, and R3. This allows for
accurate regulation of both outputs (see Typical
Operating Characteristics).
IP phones and routers require -48V. For cost-sensitive
applications, this needs to be used from an available
+5V supply. The circuit in Figure 4 is an example of
such a circuit using an off-the-shelf transformer from
Coiltronics and ICE components.
______________________________________________________________________________________
15
MAX1856
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
INPUT
4.5V TO 24V
T1
CIN
(2x) 10µF
25V
R5
10Ω
9
10
1
VCC
MAX1856
1
LDO
EXT
CS
8
6
PGND
R3
8.66kΩ
REF
RCS
33mΩ
5
3 GND
7
C1
100µF
Sanyo
100MV100AX
M1
FREQ
FB
OUTPUT
-48V
R6
100Ω
C5
1nF
ROSC
200kΩ
R4
220Ω
C3
330pF
CLDO
1µF
2
4
SYNC/SHDN
C4
1µF
D1
CFB
1nF
R1
332kΩ
4
CREF
2.2µF
D1: Central Semiconductor CMR1U-02
M1: International Rectifier IRLL2705
T1: ICE Components ICA-0635
Figure 4. -48V Output Application Circuit
16
______________________________________________________________________________________
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
Chip Information
TRANSISTOR COUNT: 1538
TOP VIEW
PROCESS: BiCMOS
LDO 1
FREQ
10 SYNC/SHDN
2
MAX1856
9
VCC
GND
3
8
EXT
REF
4
7
PGND
FB
5
6
CS
µMAX
______________________________________________________________________________________
17
MAX1856
Pin Configuration
Wide Input Range, Synchronizable,
PWM SLIC Power Supply
10LUMAX.EPS
MAX1856
Package Information
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 18
© 2001 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.