FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch Features Description The Fairchild Switch FSAL200 is a rail-to-rail quad 2:1 high-speed CMOS TTL-compatible analog multiplexer / de-multiplexer switch. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. Typical 6Ω Switch Connection Between Two Ports Minimal Propagation Delay Through the Switch Low ICC Zero Bounce in Flow-Through Mode Control Inputs Compatible with TTL Level Rail-to-Rail Signal Handling Route Communications Signals Include: - When OE is low, the select pin connects the A Port to the selected B Port output. When OE is high, the switch is open and a high-impedance state exists between the two ports. 10/100 Ethernet 100VG—AnyLAN ATM25 SONET OCI 51.8Mbps USB1.1 T1/E1 Token Ring 4/16Mbps Ordering Information Package Description Packing Method FSAL200MTC 16-Lead Thin Shrink Small Outline Package(TSSOP), JEDEC MO-153, 4.4mm Wide Rails FSAL200MTCX 16-Lead Thin Shrink Small Outline Package(TSSOP), JEDEC MO-153, 4.4mm Wide Tape and Reel FSAL200QSC 16-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150" Wide Rails 16-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150" Wide Tape and Reel Part Number FSAL200QSCX All packages are Pb-free per JEDEC standard J-SDD-020B. © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch October 2007 Figure 1. Analog Symbol Figure 2. Connection Diagram Control Input(s) OE Function X High Disconnected Low Low A=B1 High Low A=B2 Pin Descriptions Pin Names Function OE Switch Enable S Select Input A, B1, B2 Data Ports © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch Pin Configurations www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit -0.5 7.0 V -0.5 0.5 V -0.5 7.0 V VCC Supply Voltage VSW DC Switch Voltage VIN DC Input Voltage (1) IIK DC Input Diode Current at (IIK) VIN < 0V -50 mA DC Output Current 120 mA DC VCC or Ground Current ±100 mA IOUT ICC/IGND PD (1) Power Dissipation at 85°C TSTG TA 0.5 W Storage Temperature Range -65 +150 °C Ambient Temperature with Power Applied -40 +85 °C Note: 1. Input and output negative ratings may be exceeded if input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter VCC Supply Voltage VIN Control Input Voltage VSW Switch Input Voltage VOUT Min. (2) Max. Unit 3.0 5.5 V 0 VCC V VCC V Output Voltage VCC V -40 +85 °C Control Input VCC=2.3V -3.6V 0 10 Control Input VCC=4.5V -5.5V 0 5 TA Operating Temperature tr,tf Input Rise and Fall Time θJA Thermal Resistance in Still Sir FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch Absolute Maximum Ratings ns/V °C/W Note: 2. Control input must be held HIGH or LOW and it must not float. © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 3 Typical values are at 25°C unless otherwise specified. Symbol Parameter Conditions VCC(V) TA=-40°C to +85°C Min. VIH Input Voltage High VIL Input Voltage Low IOZ Off State Leakage Current RON Switch On Resistance IIN Control Input Leakage ICC Quiescent Supply Current, All Channels Off (3) IO RFLAT(ON) Max. 4.5 to 5.5 2.0 3.0 to 3.6 2.0 4.5 to 5.5 -0.5 0.8 3.0 to 3.6 -0.5 0.8 V 0 ≤ VIN ≤ 5.5V 0 to 5.5 ION=10 -30mA 4.5 to 5.5 6 12 ION=10 -30mA 3.0 to 3.6 15 22 100 ±1 3.6 ±1 VIN=VCC or GND, IOUT=0 5.5 1 µA VCC V 0 IA=-30 mA, VBN=3.15 4.5 to 5.5 0.4 2.0 IA=-10 mA, VBN=2.1 3.0 to 3.6 1.0 3.0 Output Current Bn, Bn, S-0V to 5V 4.5 to 5.5 100 3.0 to 3.6 80 µA Ω mΑ A1, B1, B2=0V to 5V 4.5 to 5.5 3 A1, B1, B2=0V to 5V 3.0 to 3.6 7 Ω Notes: 3. Measured by the voltage drop between the A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B ports). 4. ΔRON = RON maximum – RON minimum measured at identical VCC, temperature, and voltage levels. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance over the specified range of conditions. © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 Ω 5.5 VCC (3)(5) µA VIN=VCC or GND On Resistance Matching (3)(4) Between Channels On Resistance Flatness V VIN=VCC or GND Analog Signal Range ΔRON Typ. Units FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch DC Electrical Characteristics www.fairchildsemi.com 4 Typical values are at 25°C unless otherwise specified. Symbol Parameter tON Turn-On Time tOFF Turn-Off Time Q OIRR Xtalk BW D Charge Injection Off Isolation Crosstalk Conditions VCC(V) Min. Typ. Max. VBn=3V 4.5 to 5.5 10 20 VBn=1.5V 3.0 to 3.6 28 40 VBn-3V 4.5 to 5.5 5 10 VBn=1.5V 3.0 to 3.6 4 20 5.0 7 3.3 3 RL=100Ω ,f=30MHz 4.5 to 5.5 -55 RL=50Ω, f=1MHz 3.0 to 3.6 -75 RL=100Ω ,f=30MHz 4.5 to 5.5 -70 RL=50Ω, f=1MHz 3.0 to 3.6 -75 CL=0.1nF,VGEN=0 RGEN=0Ω -3db Bandwidth RL=100Ω 4.5 to 5.5 137 RL=50Ω 3.0 to 3.6 110 ΔRON/RL RL=100Ω 4.5 to 5.5 2 3.0 to 3.6 3 Units ns ns Figure Figure 3 Figure 4 Figure 3 Figure 4 pC Figure 5 dB Figure 6 dB Figure 7 MHz Figure 9 % Figure 9 Notes: 6. Guaranteed by design. 7. Off Isolation =20 log10 [VA / VBn]. Capacitance TA=+25°C, f=1MHz. Capacitance is characterized, but not tested in production. Symbol CIN CIO-B CON Parameter Conditions Typ. Units 2.3 pF Control Pin Input Capacitance VCC=0V B Port Off Capacitance VCC=5.0V and 3.0V 8 A Port Off Capacitance VCC=5.0V and 3.0V 13 Channel On Capacitance VCC=5.0V and 3.0V 15 © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 pF pF Figure Figure 10 Figure 10 FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch AC Electrical Characteristics Figure 7 www.fairchildsemi.com 5 Figure 3. AC Waveforms FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch AC Loadings and Waveforms Figure 4. ton, toff Loading © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 6 Figure 5. Charge Injection Test Figure 6. Off Isolation Figure 7. Channel On Capacitance Figure 8. Crosstalk Figure 9. Bandwidth Figure 10. © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch AC Loadings and Waveforms (Continued) Channel Off Capacitance www.fairchildsemi.com 7 FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch Physical Dimensions LAND PATTERN RECOMMENDATION TOP VIEW END VIEW SIDE VIEW DETAIL A Figure 11. 16-lead, Quarter Size Outline Package (QSOP), JEDEC MO-137. 0.150” wide Click here for tape and reel specifications, available at: http://www.fairchildsemi.com/products/analog/pdf/qsop16_tr.pdf © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 8 5.00±0.10 4.55 5.90 4.45 7.35 0.65 4.4±0.1 1.45 5.00 0.11 12° FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch Physical Dimensions (Continued) MTC16rev4 Figure 12. 16-lead, Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm wide Click here for tape and reel specifications, available at: http://www.fairchildsemi.com/products/analog/pdf/tssop16_tr.pdf © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 9 ACEx® Build it Now™ CorePLUS™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK® Power247® POWEREDGE® Power-SPM™ PowerTrench® Programmable Active Droop™ QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM® STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 Green FPS™ Green FPS™ e-Series™ GTO™ i-Lo™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MillerDrive™ Motion-SPM™ OPTOLOGIC® OPTOPLANAR® ® Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT® FAST® FastvCore™ FPS™ FRFET® Global Power ResourceSM ® PDP-SPM™ Power220® SuperSOT™-8 SyncFET™ The Power Franchise® TinyBoost™ TinyBuck™ TinyLogic® TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ μSerDes™ UHC® UniFET™ VCX™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch TRADEMARKS The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. Rev. I31 © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 10 FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch © 2002 Fairchild Semiconductor Corporation FSAL200 Rev. 1.7.1 www.fairchildsemi.com 11