GP1A05A2 GP1A05A2 OPIC Photointerrupter with Connector ■ Features ■ Outline Dimensions φ3±0.1 Depth2.0 2 ■ Applications 1 2 3 7 3.5 Slit width0.5±0.1 15 5 5 1. Copiers, Printers 2. Facsimiles 10.5 Connector made by J.S.T. MFG. CO., LTD. B3P-SHF-1AA C0.5 34.0 9.2±1 +0 0.1 − φ4 A QZ QB QD 3.5 2 3 4 QA 9 6 E 11 Y Z 1 D 5.5±1 B 8 9 X *1 Collector-emitter voltage of output transistor. *2 Collector current of output transistor. *3 The connector should be plugged in/out at normal temperature. 7.5 (Ta=25˚C) Rating Unit V −0.5 to +8 −0.5 to +28 V 50 mA −20 to +75 ˚C ˚C −40 to +85 3.0 Symbol VCC VOUT IOL Topr Tstg Protrusion of connector from holder : Max.1.0 5 6 7 ■ Absolute Maximum Ratings Parameter Suppl voltagey *1 Output voltage *2 Low level output current *3 Operating temperature *3 Storage temperature .2 0 2± . φ4 05 3.5 1. Uses 3-pin connector terminal 2. High sensing accuracy (Slit width : 0.5mm) 3. Wide gap between light emitter and detector (5mm) (Unit : mm) 11±0.1 12±0.1 ❈ Unspecified tolerances shall be as follows Dimensions (d) Tolerance d<4.0 ±0.2 4.0<=d<16.0 ±0.3 16.0<=d ±0.5 1 Voltage regulator Amp. 2 1 3 2 3 VCC GND VO * "OPIC" (Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signal-processing circuit integrated onto a single chip. Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/ GP1A05A2 ■ Electro-optical Characteristics Parameter Operating supply voltage Low level supply current Low level output voltage High level supply current High level output voltage *4 Response frequency (Unless otherwise specified, VCC=5V, Ta=25˚C) Unit TYP. MAX. MIN. Symbol Conditions V − 4.5 5.5 VCC mA − − 30 ICCL Light beam uninterrupted V − − 0.35 VOL Light beam uninterrupted, IOL=16mA mA − − 30 Light beam interrupted ICCH V − − Light beam interrupted, RL=47kΩ VCC×0.9 VOH No DC output is allowed, RL=47kΩ Hz − 3 000 − f *4 Refer to Fig.1 Fig.1 Response Frequency 0.5 0.5 2.0 Disk Response frequency is measured with the disk shown below being rotated. (Unit : mm) Fig.3 Low Level Output Voltage vs. Low Level Output Current 60 1.0 50 0.5 Low level output voltage VOL (V) Low level output current IOL (mA) Fig.2 Low Level Output Current vs. Ambient Temperature 40 30 20 16.6 10 0 −20 VCC=5V Ta=25˚C 0.2 0.1 0.05 0.02 0.01 0 25 50 75 Ambient temperature Ta (˚C) 100 1 2 5 10 20 50 Low level output current IOL (mA) 100 GP1A05A2 Fig.4 Low Level Output Voltage vs. Ambient Temperature Fig.5 Supply Current vs. Supply Voltage 0.6 30 0.5 Supply current ICC (mA) Low level output voltage VOL (V) VCC=5V 0.4 IOL=30mA 0.3 0.2 16mA 0.1 20 Ta=−20˚C ICCL 10 ICCH +25˚C +75˚C Ta=−20˚C, +25˚C, +75˚C 5mA 0 0 −25 0 25 50 75 4.5 100 5.0 5.5 Supply voltage VCC (V) Ambient temperature Ta (˚C) Fig.6 Detecting Position Characteristics (1) VCC=5V Ta=25˚C RL=47kΩ Fig.7 Detecting Position Characteristics (2) VCC=5V Ta=25˚C RL=47kΩ Output OFF Output OFF Shield d Shield h Output ON 0 1 2 3 4 5 6 Shield distance d (mm) Detecting position d=3.5±0.3mm 7 Output ON 0 1 2 3 4 5 6 Shield distance h (mm) +2.0 Detecting position h=3.0 −1.5mm 7 GP1A05A2 ■ Recommended Connectors on the Inserted Side ◆ JAPAN SOLDERLESS TERMINAL MFG. CO., LTD. made Housing Model No. H3P-SHF-AA AWG size Special terminal Model. No. AWG 28 to 22 AWG 30 to 28 (Natural color • bulk) S3P-SHF-1 Material Model No. Brass SHF-001T-0.8SS Copper phosphide SHF-001T-0.8BS Brass SHF-002T-0.8SS Copper phosphide SHF-002T-0.8BS AWG size AWG 27 to 22 AWG 30 to 28 Material Model No. Brass SHF-001T-0.8P Copper phosphide − Brass SHF-002T-0.8P Copper phosphide − ■ Precautions for Use 1. It is recommended that a by-pass capacitor of more than 0.01µF be added between VCC and GND near the device in order to stabilize power supply line. 2. Please don't carry out immersion cleaning or ultrasonic cleaning to avoid keeping solvent inside case of this device. 3. Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent. However, do not perform the above cleaning using a soft cloth with cleaning solvent in the marking portion. In this case, use only the following type of cleaning solvent used for wiping off : Ethyl alcohol, Methyl alcohol, Isopropyl alcohol, When the cleaning solvents except for specified materials are used, please consult us. 4. As for other general cautions, refer to the chapter "Precautions for Use. " Application Circuits NOTICE ●The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ●Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. ●Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). ●Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. ●If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. ●This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. ●Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 115