GP1A05/GP1A22LC/GP1A23LC/GP1A25LC OPIC Photointerrupter with Connector GP1A05/GP1A22LC/ GP1A23LC/GP1A25LC ■ Features ■ Applications 1. Uses 3-pin connector terminal 2. High sensing accuracy ( Slit width : 0.5mm ) 3. Wide gap between light emitter and detector ( 5mm ) 1. Copiers, Printers 2. Facsimiles * “ OPIC ” ( Optical IC ) is a trademark of SHARP Corporation. An OPIC consists of a light-detecting element and signal-processing circuit integrated onto a single chip. ■ Outline Dimensions ( Unit : mm ) GP1A22LC ( Same as GP1A05 except connector ) GP1A05 φ 4.2 ± 0.2 3 2 (2.5) 4.0+- 00.1 11.0± 0.1 12.0± 0.1 ❈ JAPAN AMP made EI 3-pin connector 171825-3 1 (2.5) (2.5) * Unspecified tolerances shall be as follows ; Dimensions(d) Tolerance d < 4.0 ± 0.2 4.0<=d < 16.0 ± 0.3 16 <=d ± 0.5 * ( ) : Reference dimensions (2.5) * ( ) : Reference dimensions ❈ 2 protrusion of connector from holder: MAX.1.0 ❈ 1 JAPAN SOLDERLESS TERMINAL MSG. CO., LTD. made connector B3P-SHF-1AA Recommended connectors on the inserted side Housing : H3P-SHF-AA Terminal : SHF-001T-0.8SS etc. ❈❈ ( 9.2 ) Recommended connectors on the inserted side 172053-3 etc. ❈❈ 11.0± 0.3 11.0 ± 0.3 GP1A25LC ( Same as GP1A05 except connector ) 1 V CC 2 GND 3 VO 3 2 1 (2.5) * ( ): Reference dimensions ❈ JAPAN SOLDERLESS TERMINAL MSG. CO., LTD. made connector BS3P-SHF-1AA Recommended connectors on the inserted side Housing : (H3P-SHF-AA ) etc ❈❈ Terminal : (SHF-001T-0.8SS ) etc. ❈ 2 3 (2.5) (5.9) (9.9) ❈ 5.5 ± 1.0 1 1 V CC 2 GND 3 VO 1 V CC 2 GND 3 VO GP1A23LC ( Same as GP1A05 except connector ) (2.5) 3 2 ❈1 5.5 ± 1.0 C0.5 5.5 ± 1.0 3.0 7.5 10.5 3.5 Slit width 0.5 ❈ φ 7.0 (10.4) 34.0 15.0 5.0 5.0 1.0MAX❈ 2 φ 3.0 ± 0.1Depth2.0 3.5 11.0 11.0 3.5 ± 0.3 2.0 1 (2.5) 1 V CC 2 GND 3 VO * ( ) : Reference dimensions ❈ MOLEX JAPAN CO., LTD. made connector 5267-03A Recommended connectors on the inserted side Housing : 5264-03 Terminal : 5263PBT ❈❈ Recommended connectors on the inserted side are show on the following 3rd page. “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.” GP1A05/GP1A22LC/GP1A23LC/GP1A25LC Internal connection diagram ( Common to 4 models ) 1 Voltage regulator Amp. 2 1 V CC 2 GND 3 VO 3 ■ Absoulte Maximum Ratlngs ( Ta = 25˚C ) Parameter Supply GP1A05 GP1A22LC / GP1A23LC / GP1A25LC voltage *1 Output voltage *2 Low level output current *3 Operating temperature *3 Storage GP1A05 / GP1A22LC / GP1A23LC temperaGP1A25LC ture Symbol V CC VO I OL T opr T stg Rating - 0.5 to + 10 - 0.5 to + 8 - 0.5 to + 28 50 - 20 to + 75 - 40 to + 85 - 30 to + 85 Unit V V mA ˚C ˚C *1 Collector-emitter voltage of output transistor *2 Collector current of output transistor *3 The connector should be plugged in/out at normal temperature. ■ Electro-optical Characteristics Parameter Operating supply voltage Low level supply current Low level output voltage High level supply current High level output voltage *5 Response frequency ( Unless otherwise specified, Vcc = 5V, Ta = 25˚C ) Symbol V CC I CCL V OL I CCH V OH f Conditions Light beam uninterrupted Light beam uninterrupted,I OL = 16mA Light beam interrupted Light beam interrupted,R L = 47k Ω *4 R L = 47k Ω MIN. 4.5 V CC x 0.9 - *4 No DC output is allowed. *5 Response frequency is measured with the disk shown below being rotated.( Unit : mm ) 0.5 0.5 2.0 Disk TYP. - MAX. 5.5 30 0.35 30 3 000 Unit V mA V mA V Hz GP1A05/GP1A22LC/GP1A23LC/GP1A25LC Fig. 2 Low Level Output Voltage vs. Low Level Output Current 60 1.0 50 0.5 Low levle output voltage VOL (V ) Low level output current I OL ( mA ) Fig. 1 Low Level Output Current vs. Ambient Temperature 40 30 20 10 V CC = 5V Ta = 25˚C 0.2 0.1 0.05 0.02 0.01 0 - 20 0 25 50 75 2 1 100 5 10 20 50 100 Low level output current I OL ( mA ) Ambient temperature Ta ( ˚C ) Fig. 3 Low Level Output Voltage vs. Ambient Temperature Fig. 4 Supply Current vs. supply Voltage 0.6 30 0.5 Supply current I CC ( mA ) Low levle output voltage VOL ( V) VCC = 5V 0.4 I OL = 30mA 0.3 0.2 16mA 0.1 20 Ta =- 20˚C I CCL 10 I CCH + 25˚C + 75˚C T a =- 20˚C,+ 25˚C,+ 75˚C 5mA 0 - 25 0 0 25 50 75 4.5 100 5.0 5.5 Supply voltage VCC ( V) Ambient temperature Ta ( ˚C ) Fig. 5 Detecting Position Characteristics ( 1 ) V CC = 5V Ta = 25˚C R L = 47kΩ Fig. 6 Detecting Position Characteristics ( 2 ) V CC = 5V Ta = 25˚C R L = 47kΩ Output High d Output High Shield Shield h Output Low 0 1 2 3 4 5 6 7 Shield distance d ( mm ) Detecting position d = 3.5 ± 0.3mm (GP1A22LC / GP1A23LC / GP1A25LC : d = 3.5 ± 0.5mm ) Output Low 0 1 2 3 4 5 Shield distance h ( mm ) + 2.0 Detecting position h= 3.0 - 1.5mm 6 7 GP1A05/GP1A22LC/GP1A23LC/GP1A25LC ■ Recommended Connectors on the Inserted Side Recommended connectors on the inserted side for GP1A05,GP1A22LC, and GP1A23LC are shown below. << GP1A05 >> ● JAPAN AMP made El series connectors ● JAPAN AMP made El series connectors ( standard type ) ( low profile type ) Natural Black Blue Green Red color Housing Model No. 171822-3 2-171822-3 4-171822-3 6-171822-3 8-171822-3 AWG Product Material Model No. size shape Brass 170204-1 Bulk Copper 170204-2 phosphide AWG 26 to 20 Brass 170262-1 Special Chain Copper 170262-2 terminal phosphide Model. No. Brass 170205-1 Bulk Copper 170205-2 phosphide AWG 30 to 26 Brass 170263-1 Chain Copper 170263-2 phosphide Natural Black Blue Green Red color Housing Model No. 172142-3 2-172142-3 4-172142-3 6-172142-3 8-172142-3 AWG Special Product shape Model No. size terminal Bulk 170369-1 AWG Model. No. 26 to 22 Chain 170354-1 ( Material: Copper Bulk 170370-1 AWG phosphide ) 30 to 26 Chain 170355-1 Housing color Housing color ● JAPAN AMP made El series connectors ( amp mass termination ) AWG26 AWG24 AWG22 Housing-terminal AWG28 ( Natural ( Black ) (Red) ( ) Green united type color ) connector 172054-3 172053-3 172052-3 172051-3 * Terminal Material : Copper phosphide <<GP1A22LC/ GP1A23LC>> ● JAPAN SOLDERLESS TERMINAL MSG. CO., LTD. made ( Natural color • bulk ) Housing Model No. H3P-SHF-AA AWG size Special terminal Model. No. Material Brass AWG Copper 26 to 22 phosphide Brass AWG Copper 30 to 26 phosphide S3P-SHF-1 Model No. SHF-001T-0.8SS AWG size Material Brass AWG Copper SHF-001T-0.8BS 27 to 22 phosphide SHF-002T-0.8SS Brass AWG Copper SHF-001T-0.8BS 30 to 28 phosphide Model No. SHF-001T-0.8P SHF-002T-0.8P - ■ Precautions for Use ( 1 ) It is recommended that a by-pass capacitor of more than 0.01 µ F be added betw een VCC and GND near the device in order to stabilize power supply line. ( 2 ) In this product, the PWB is fixed with a rear cover, and cleaning solvent may remain inside the case; therefore, dip cleaning or ultrasonic cleaning is prohibited. ( 3 ) Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent. However, do not perform the above cleaning using a soft cloth with cleaning solvent in the marking portion. In this case, use only the following type of cleaning solvent used for wiping off: Ethyl alcohol, Methyl alcohol, Isopropyl alcohol, When the cleaning solvents except for specified materials are used, please consult us. ( 4 ) As for other general cautions, refer to the chapter “ Precautions for Use ” .