FAIRCHILD FODM3062

FODM3062/FODM3063/FODM3082/FODM3083
4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac
Driver Output Optocouplers
Features
Description
■ dv/dt of 600V/µs guaranteed
■ Compact 4-pin surface mount package
The FODM306X and FODM308X series consist of an
infrared emitting diode optically coupled to a monolithic
silicon detector performing the function of a zero voltage
crossing bilateral triac driver, and is housed in a compact
4-pin mini-flat package. The lead pitch is 2.54mm. They
are designed for use with a triac in the interface of logic
systems to equipment powered from 115/240 VAC lines,
such as solid state relays, industrial controls, motors,
solenoids and consumer appliances.
(2.4mm maximum standoff height)
■ Zero voltage crossing
■ Peak blocking voltage: 600V (FODM306X)
800V (FODM308X)
■ Available in tape and reel quantities of 500 and 2500.
■ C-UL, UL and VDE certifications pending
Applications
■
■
■
■
■
■
■
■
Solenoid/valve controls
Lighting controls
Static power switches
AC motor drives
Temperature controls
E.M. contactors
AC motor starters
Solid state relays
Package Dimensions
4.40±0.20
ANODE 1
4 MAIN TERM.
2.54±0.25
3.60±0.30
2.00±0.20
CATHODE 2
5.30±0.30
ZERO
CROSSING
CIRCUIT
3 MAIN TERM.
0.20±0.05
0.10±0.10
0.40±0.10
7.00 +0.2
–0.7
Note:
All dimensions are in millimeters.
©2006 Fairchild Semiconductor Corporation
FODM306X/FODM308X Rev. 1.0.4
1
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
March 2007
Symbol
Parameter
Rating
Units
TOTAL PACKAGE
TSTG
Storage Temperature
-55 to +150
°C
TOPR
Operating Temperature
-40 to +100
°C
EMITTER
IF (avg)
Continuous Forward Current
60
mA
IF (pk)
Peak Forward Current (1µs pulse, 300pps.)
1
A
VR
Reverse Input Voltage
6
V
PD
Power Dissipation (No derating required over operating temp. range)
100
mW
IT(RMS)
On-State RMS Current
70
mA (RMS)
VDRM
Off-State Output Terminal Voltage
FODM3062/FODM3063
600
V
FODM3082/FODM3083
800
DETECTOR
PD
Power Dissipation (No derating required over operating temp. range)
2
FODM306X/FODM308X Rev. 1.0.4
300
mW
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Absolute Maximum Ratings (TA = 25°C unless otherwise specified)
Individual Component Characteristics
Symbol
Parameter
Test Conditions
Min.
Typ.*
Max.
Units
EMITTER
VF
Input Forward Voltage
IF = 30mA
1.5
V
IR
Reverse Leakage Current
VR = 6V
100
µA
500
nA
DETECTOR
IDRM1
Peak Blocking Current,
Either Direction
Rated VDRM, IF = 0(1)
dV/dt
Critical Rate of Rise of
Off-State Voltage
IF = 0 (Figure 1)(2)
600
V/µs
Transfer Characteristics
Symbol DC Characteristics
IFT
LED Trigger Current
Test Conditions
Device
Main Terminal
Voltage = 3V(3)
Min.
Typ.*
FODM3062
Max.
Units
10
mA
FODM3082
FODM3063
5
FODM3083
IH
VTM
Holding Current,
Either Direction
All
Peak On-State Voltage, IF = Rated IFT,
Either Direction
ITM = 100mA peak
All
300
µA
3
V
Zero Crossing Characteristics
Symbol
VIH
IDRM2
Characteristics
Test Conditions
Device
Min.
Typ.*
Max.
Units
Inhibit Voltage,
MT1-MT2 Voltage
above which device
will not trigger
IF = Rated IFT
All
20
V
Leakage in Inhibit
State
IF = Rated IFT,
Rated VDRM,
Off-State
All
500
µA
Max.
Units
Isolation Characteristics
Characteristics
Steady State Isolation
Voltage(4)
Test Conditions
(1 Minute)
R.H. = 40% to 60%
Symbol
Device
Min.
VISO
All
3750
Typ.*
VRMS
Notes:
* All typicals at 25°C.
1. Test voltage must be applied within dv/dt rating.
2. This is static dv/dt. See Figure 1 for test circuit. Commutating dv/dt is function of the load-driving thyristor(s) only.
3. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended operating
IF lies between max IFT (10mA for FODM3062/82, 5mA for FODM3063/83) and absolute max IF (60 mA).
4. Steady state isolation voltage, VISO, is an internal device dielectric breakdown rating. For this test, pins 1 & 2 are
common, and pins 3 & 4 are common.
3
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Electrical Characteristics (TA = 25°C)
Fig. 1 LED Forward Voltage vs. Forward Current
Fig. 2 Leakage Current vs. Ambient Temperature
1000
1.8
VDRM = 600V
1.7
IDRM - LEAKAGE CURRENT (nA)
VF - FORWARD VOLTAGE (V)
1.6
1.5
1.4
TA = -40°C
1.3
1.2
TA = 25°C
1.1
100
10
1
TA = 100°C
1.0
0.1
-40
0.9
1
10
100
-20
Fig. 3 Holding Current vs. Ambient Temperature
20
60
80
100
Fig. 4 Trigger Current vs. Ambient Temperature
VTM = 3V
NORMALIZED TO TA = 25°C
I FT - TRIGGER CURRENT (NORMALIZED)
NORMALIZED TO TA = 25°C
1.0
0.1
-40
40
1.6
10
I H - HOLDING CURRENT (NORMALIZED)
0
T A - AMBIENT TEMPERATURE (°C)
IF - FORWARD CURRENT (mA)
-20
0
20
40
60
80
100
1.4
1.2
1.0
0.8
0.6
0.8
-40
T A - AMBIENT TEMPERATURE (°C)
-20
0
20
40
60
80
100
T A - AMBIENT TEMPERATURE (°C)
4
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Curves
Fig. 5 LED Current Required to Trigger vs. LED Pulse Width
Fig. 6 Off-State Output Terminal Voltage vs. Ambient Temperature
1.4
TA =T25°C
A
NORMALIZED TO PW IN >> 100µs
10
8
6
4
2
NORMALIZED TO TA = 25°C
1.3
1.2
(NORMALIZED)
V DRM- OFF-STATE OUTPUT TERMINAL VOLTAGE
IFT - LED TRIGGER CURRENT (NORMALIZED)
12
1.1
1.0
0.9
0.8
0.7
0.6
-40
0
1
10
0
-20
100
20
40
60
80
100
T A - AMBIENT TEMPERATURE (°C)
PW IN - LED TRIGGER PULSE WIDTH (°C)
Fig. 7 On-State Characteristics
800
TA = 25°C
ITM - ON-STATE CURRENT (mA)
600
400
200
0
-200
-400
-600
-800
-4
-3
-2
-1
0
1
2
3
4
VTM - ON-STATE VOLTAGE (V)
5
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Curves
RTEST
800V (FODM3082) Vdc
(FODM3083)
600V (FODM3062)
(FODM3063)
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
3. The worst-case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt
to be gradually increased until the D.U.T. continues to trigger
in response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering. tRC is measured at this point
and recorded.
R = 10 kΩ
CTEST
PULSE
INPUT
MERCURY
WETTED
RELAY
X100
SCOPE
PROBE
D.U.T.
Vmax = 800V (FODM3082, FODM3083)
= 600V (FODM3062, FODM3063)
APPLIED VOLTAGE
WAVEFORM
378V (FODM3062, FODM3063)
504V (FODM3082, FODM3083)
dv/dt =
0 VOLTS
τRC
0.63 Vmax
τRC
378
= τ
(FODM3062, FODM3063)
RC
504
(FODM3082, FODM3083)
= τ
RC
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
Figure 8. Static dv/dt Test Circuit
Rin
1
Typical circuit for use when hot line switching of 240VAC
is required. In this circuit the “hot” side of the line is
switched and the load connected to the cold or neutral
side. The load may be connected to either the neutral or
hot line.
Rin is calculated so that IF is equal to the rated IFT of the
part, 5mA for the FODM3063/83 and 10mA for the
FODM3062/82. The 39Ω resistor and 0.01µF capacitor are
for snubbing of the triac and may or may not be necessary
depending upon the particular triac and load used.
360 Ω
4
HOT
VCC
2
FODM3062
FODM3063
FODM3082
FODM3083
39*
3
240 VAC
0.01
330
LOAD
NEUTRAL
For highly inductive loads (power factor < 0.5), change this value to 360 ohms.
*
Figure 9. Hot-Line Switching Application Circuit
240 VAC
R1
1
VCC
Rin
2
D1
Suggested method of firing two, back-to-back
SCR’s, with a Fairchild triac driver. Diodes can
be 1N4001; resistors, R1 and R2, are optional
330 ohms.
4
FODM3062
FODM3063
FODM3082
FODM3083
SCR
3
SCR
360 Ω
R2
D2
LOAD
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
Figure 10. Inverse-Parallel SCR Driver Circuit (240VAC)
6
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Curves
Option
Description
No option
Bulk (100 units/tube)
V
VDE Approved
R1
Tape and Reel (500 units)
R2
Tape and Reel (2500 units)
R1V
Tape and Reel (500 units) and VDE Approved
R2V
Tape and Reel (2500 units) and VDE Approved
Marking Information
1
3063
2
V X YY R
6
3
4
5
Definitions
1
Fairchild logo
2
Device number
3
VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
4
One digit year code
5
Two digit work week ranging from ‘01’ to ‘53’
6
Assembly package code
7
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Ordering Information
K0
P2
P0
t
D0
E
A0
W1
W
B0
d
F
D1
P
2.54 Pitch
Symbol
Dimensions
Tape Width
W
12.00±0.3
Tape Thickness
t
0.30±0.05
Description
Sprocket Hole Pitch
P0
4.00±0.1
Sprocket Hole Dia.
D0
1.50±0.1
Sprocket Hole Location
E
1.75±0.1
Pocket Location
F
5.50±0.1
P2
2.00±0.1
Pocket Pitch
P
8.00±0.1
Pocket Dimension
A0
3.90±0.1
B0
7.45±0.1
K0
2.45±0.1
Pocket Hole Dia.
D1
1.50±0.1
Cover Tape Width
W1
9.30±0.1
Cover Tape Thickness
d
Max. Component Rotation or Tilt
Devices Per Reel
Reel Diameter
20˚ max
R1
500
R2
2500
R1
178 mm (7")
R2
330 mm (13")
8
FODM306X/FODM308X Rev. 1.0.4
0.062±0.02
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Tape and Reel Information
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Footprint Drawing for PCB Layout
0.80
1.00
6.50
2.54
Note:
All dimensions are in mm.
Recommended Infrared Relow Soldering Profile
• Peak reflow temperature: 260°C (package surface temperature)
• Time of temperature higher than 245°C: 40 seconds or less
• Number of reflows: 3
10 s
Temperature (°C)
300
260°C
245°C
250
200
150
40 s
100
50
0
0
50
100
150
200
250
300
Time (s)
9
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
®
ACEx
Across the board. Around the world.¥
ActiveArray¥
Bottomless¥
Build it Now¥
CoolFET¥
CROSSVOLT¥
CTL™
Current Transfer Logic™
DOME¥
2
E CMOS¥
®
EcoSPARK
EnSigna¥
FACT Quiet Series™
®
FACT
®
FAST
FASTr¥
FPS¥
®
FRFET
GlobalOptoisolator¥
GTO¥
Programmable Active Droop¥
®
QFET
QS¥
QT Optoelectronics¥
Quiet Series¥
RapidConfigure¥
RapidConnect¥
ScalarPump¥
SMART START¥
®
SPM
STEALTH™
SuperFET¥
SuperSOT¥-3
SuperSOT¥-6
SuperSOT¥-8
SyncFET™
TCM¥
®
The Power Franchise
HiSeC¥
i-Lo¥
ImpliedDisconnect¥
IntelliMAX¥
ISOPLANAR¥
MICROCOUPLER¥
MicroPak¥
MICROWIRE¥
MSX¥
MSXPro¥
OCX¥
OCXPro¥
®
OPTOLOGIC
®
OPTOPLANAR
PACMAN¥
POP¥
®
Power220
®
Power247
PowerEdge¥
PowerSaver¥
®
PowerTrench
®
TinyLogic
TINYOPTO¥
TinyPower¥
TinyWire¥
TruTranslation¥
PSerDes¥
®
UHC
UniFET¥
VCX¥
Wire¥
™
TinyBoost¥
TinyBuck¥
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE
APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER
ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S
WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.
2. A critical component in any component of a life support,
device, or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or In Design
This datasheet contains the design specifications for product
development. Specifications may change in any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be
published at a later date. Fairchild Semiconductor reserves the right to
make changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice to improve
design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been
discontinued by Fairchild Semiconductor. The datasheet is printed for
reference information only.
Rev. I24
10
FODM306X/FODM308X Rev. 1.0.4
www.fairchildsemi.com
FODM3062/FODM3063/FODM3082/FODM3083 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an
exhaustive list of all such trademarks.