Ordering number : ENA0378 Monolithic Linear IC LA73060V Wideband 75Ω Video Driver Overview This LA73060V is a wideband 75Ω Video Driver IC. The LA73060V is ideal for use the video output driver such as TVmonitor and DVD-player equipment. Functions • 6channel output. • 6MHz or 30MHz low pass filter. • 6dB amplifier. • Output mute. • Y/C_MIX. • Standby mode. Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Pd max Ta ≤ 75°C ∗ Unit 7.0 V 780 mW Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +150 °C ∗ When mounted on a 114.3×76.1×1.6mm3 glass epoxy board. Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommending operation voltage VCC Operating voltage range Input pin voltage application range VCC op VIN Conditions Ratings Unit 5.0 V 4.75 to 5.25 V -0.3 to VCC op + 0.3 V Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. N2206 / 32406 MS OT 20051216-S00016 No.A0378-1/10 Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Symbol SIG Level Freq. IN OUT [Vp-p] [Hz] point point Ratings Conditions min typ max Unit Current dissipation 1 ICC1 No signal. 69.0 87.0 105.0 mA Current dissipation 2 ICC2 Standby mode,No signal. 0.3 0.4 0.5 mA 2.8 3.0 3.2 V Output gain. 5.5 6.0 6.5 dB Output gain. 5.5 6.0 6.5 dB -3 0.0 3 dB -3 0.0 3 dB -40 -35 dB -40 -35 dB -1 0.0 1 dB -1 0.0 1 dB -5 -2.5 0 dB -5 -2.5 0 dB -40 -35 dB -40 -35 dB Reguratur voltage Voltage gain 1 Voltage gain 2 Frequency REG3V VG1 VG2 3 0.3 100k T1 T6A T35 T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 T12A T24 T16A T19 T1 6MHz LPF is selected. T35 f = 6MHz / 100kHz. (CV,Y,Py,R,G,B) T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 6MHz LPF is selected. characteristics 2 T12A T24 f = 6MHz / 100kHz. (C,Pr,Pb) T16A T19 Frequency T4A T1 6MHz LPF is selected. T6A T35 f = 27MHz / 100kHz. (CV,Y,Py,R,G,B) T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 6MHz LPF is selected. T12A T24 f = 27MHz / 100kHz. VF4 (SD) 1 3 0.3 6M characteristics 3 Frequency VF3 (SD) 0.3 6M T4A T6A 3 0.3 100k characteristics 1 VF2 (SD) 1 0.3 T4A Frequency VF1 (SD) T27 1 0.3 27M 27M characteristics 4 (C,Pr,Pb) Frequency VF5 (HD) 1 0.3 20M characteristics 5 Frequency VF6 (HD) 3 0.3 20M characteristics 6 Frequency VF7 (HD) 1 0.3 30M characteristics 7 Frequency VF8 (HD) 3 0.3 30M characteristics 8 Frequency VF9 (HD) 1 0.3 75M characteristics 9 Frequency characteristics 10 VF10 (HD) 3 0.3 75M T16A T19 T14A T22 30MHz LPF is selected. T12A T30 f =20MHz / 100kHz. T14A T28 T16A T26 T12A T24 30MHz LPF is selected. T16A T19 f = 20MHz / 100kHz. T14A T22 30MHz LPF is selected. T12A T30 f = 30MHz / 100kHz. T14A T28 T16A T26 T12A T24 30MHz LPF is selected. T16A T19 f = 30MHz / 100kHz. T14A T22 30MHz LPF is selected. T12A T30 f = 75MHz / 100kHz. T14A T28 T16A T26 T12A T24 30MHz LPF is selected. T16A T19 f = 75MHz / 100kHz. Continued on next page. LA73060V Continued from preceding page. Parameter 2nd order distortion 1 Symbol Dst1 (SD) SIG 1 Level Freq. IN OUT [Vp-p] [Hz] point point 0.7 4M (SD) 2nd order distortion 2 Dst2 (SD) 3 0.7 4M (SD) 2nd order distortion 3 Dst3 (HD) 1 0.7 10M (HD) 2nd order distortion 4 Dst4 (HD) 3 0.7 10M (HD) Clipping output level 1 Clipping output level 2 Amount of mute VO max1 VO max2 VM1 3 3 1 2 2 0.3 100k 100k 4M attenuation 1 Amount of mute VM2 3 0.3 4M attenuation 2 Crosstalk between VCT1 1 0.3 4M channels 1 T4A T1A T6A T35A T14A T22A T12A T30A T14A T28A T16A T26A T8A T32A T12A T24A T16A T19A T14A T22A T12A T30A T14A T28A T16A T26A T8A T32A T12A T24A T16A T19A T4A T1 T6A T35 T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 T12A T24 T16A T19 T4A T1 T6A T35 T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 T12A T24 T16A T19 T4A Ratings Conditions Unit min typ max -40 -35 dB -40 -35 dB -40 -35 dB -40 -35 dB Output level for clipping. 2.2 2.4 Vp-p Output level for clipping. 2.2 2.4 Vp-p -60 -50 dB -60 -50 dB -60 -50 dB -60 -50 dB T6A T14A T12A T14A T16A Crosstalk between channels 2 VCT2 3 0.3 4M T8A T12A T16A Continued on next page. No.A0378-3/10 LA73060V Continued from preceding page. Parameter Video S/N 1 Symbol SIG VS/N1 (SD) 2 Level Freq. IN OUT [Vp-p] [Hz] point point 0.65 (SD) Video S/N 2 VS/N2 (HD) 2 0.65 (HD) Group delay 1 GD1 (SD) 1 0.3 6M (SD) Group delay 2 GD2 (SD) 3 0.3 6M (SD) Group delay 3 GD3 (HD) 1 0.3 30M (HD) Group delay 4 GD4 (HD) 3 0.3 (HD) 30M Ratings Conditions Unit min T4A T1A T6A T35A VIN = Video (50% White), The band is between 100kHz T14A T22A and 4.2MHz T12A T30A T14A T28A T16A T26A T14A T22A T12A T30A VIN = Video (50% White), The band is between 100kHz T14A T28A and 30MHz T16A T26A T4A T1 Input / Output delay time. T6A T35 f=6MHz/100kHz T14A T22 T12A T30 T14A T28 T16A T26 T8A T32 Input / Output delay time. T12A T24 f=6MHz/100kHz T16A T19 T14A T22 Input / Output delay time. T12A T30 f=30MHz/100kHz T14A T28 T16A T26 T12A T24 Input / Output delay time. T16A T19 f=30MHz/100kHz typ max -70 -60 dB -60 -50 dB 20 30 ns 20 30 ns 10 20 ns 10 20 ns Input signal SIG.1 SIG.2 SIG.3 Truth Table SW No. Pin No. SW1 5 SW2 7 SW3 11 Function H (2.3V to VCC) L (0 to 0.7V) Y/C MIX OFF ON CV Mute control OFF ON Power save control OFF ON SW4 13 Input control CLAMP ON(RGB Mode) BIAS ON(Component Mode) SW5 15 Filter control 6MHz LPF ON(RGB Mode) 30MHz LPF ON(Component Mode) SW6 17 Output control RGB ON(RGB Mode) Component ON(Component Mode) SW7 20 RGB&Component Mute control OFF ON No.A0378-4/10 LA73060V Package Dimensions unit : mm 3247A 7.6 19 0.5 5.6 36 1 18 0.2 (0.7) 0.8 (1.5) 0.1 15.0 1.7max 0.3 SANYO : SSOP36(275mil) No.A0378-5/10 LA73060V Block Diagram No.A0378-6/10 LA73060V Test Circuit Diagram No.A0378-7/10 LA73060V Pin Functions Pin No. Pin Name 1 CV_OUT 35 Y_OUT 2 CV_SAG_IN 21 34 Py_SAG_IN Y_SAG_IN 4 CV_IN 6 Y_IN 14 G/Py_IN 5 SW1 7 SW2 11 SW3 13 SW4 15 SW5 17 SW6 20 SW7 3 VCC (CV) VCC (RGB&COMP) VCC (Driver COMP) 10 25 31 36 Signal Wave Form Equivalent Circuit Y_IN,Py_IN RGB *See the Truth Table. VCC (Driver RGB) VCC (Driver CV) Continued on next page. No.A0378-8/10 LA73060V Continued from preceding page. Pin No. Pin Name 8 C_IN 12 R/Pr_IN B/Pb_IN 16 Signal Wave Form Equivalent Circuit RGB Component 26 B_OUT 28 G_OUT 30 R_OUT 19 24 Pb_OUT Pr_OUT 32 C_OUT 9 GND (CV) 18 GND (RGB&COMP) 23 GND (Driver COMP) 29 GND (Driver RGB) 33 GND (Driver CV) 27 REG3V DC : 3.0V No.A0378-9/10 LA73060V Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of March, 2006. Specifications and information herein are subject to change without notice. PS No.A0378-10/10