CYF0018V, CYF0036V CYF0072V 18/36/72 Mbit Programmable FIFOs 18/36/72/144 Mbit Programmable FIFOs Features Functional Description ■ Memory organization ❐ Industry's largest first in first out (FIFO) memory densities: 18 Mbit, 36 Mbit, and 72 Mbit ❐ Selectable memory organization: ×9, ×12, ×16, ×18, ×20, ×24, ×32, ×36 ■ Up to 133-MHz clock operation ■ Unidirectional operation ■ Independent read and write ports ❐ Supports simultaneous read and write operations ❐ Reads and writes operate on independent clocks up to a maximum ratio of two enabling data buffering across clock domains ❐ Supports multiple I/O voltage standard: low voltage complementary metal oxide semiconductor (LVCMOS) 3.3 V and 1.8 V voltage standards. ■ Input and output enable control for write mask and read skip operations ■ Mark and retransmit: resets read pointer to user marked position ■ Empty, full, half-full, and programmable almost-empty and almost-full status flags with preselected offsets ■ Flow-through mailbox register to send data from input to output port, bypassing the FIFO sequence As implied by the name, the functionality of the FIFO is such that the data is read out of the read port in the same sequence in which it was written into the write port. The data is sequentially written into the FIFO from the write port. If the writes and inputs are enabled, the data on the write port gets written into the device at the rising edge of the write clock. Enabling the reads and outputs fetches data on the read port at every rising edge of the read clock. Both reads and writes can occur simultaneously at different speeds provided the ratio between read and write clock is in the range of 0.5 to 2. Appropriate flags are set whenever the FIFO is empty, full, half-full, almost-full, or almost-empty. ■ Configure programmable flags and registers through serial or parallel modes The device also supports mark and retransmit of data, and a flow-through mailbox register. ■ Separate serial clock (SCLK) input for serial programming ■ Master reset to clear entire FIFO ■ Partial reset to clear data but retain programmable settings ■ Joint test action group (JTAG) port provided for boundary scan function ■ Industrial temperature range: –40 °C to +85 °C All product features and specs are common to all densities ( CYF0072V, CYF0036V, and CYF0018V) unless otherwise specified. All descriptions are given assuming the device is CYF0072V operated in ×36 mode. They hold good for other densities (CYF0036V, and CYF0018V) and all port sizes ×9, ×12, ×16, ×18, ×20, ×24 and ×32 unless otherwise specified. the only difference will be in the input and output bus width. Table 1 shows the part of bus with valid data from D[35:0] and Q[35:0] in ×9, ×12, ×16, ×18, ×20, ×24, ×32 and ×36 modes. Cypress Semiconductor Corporation Document Number: 001-53687 Rev. *H • The Cypress programmable FIFO family offers the industry’s highest-density programmable FIFO memory device. It has independent read and write ports, which can be clocked up to 133 MHz. User can configure input and output bus sizes. The maximum bus size of 36 bits enables a maximum data throughput of 4.8 Gbps. The read and write ports can support multiple I/O voltage standards. The user-programmable registers enable user to configure the device operation as desired. The device also offers a simple and easy-to-use interface to reduce implementation and debugging efforts, improve time-to-market, and reduce engineering costs. This makes it an ideal memory choice for a wide range of applications including multiprocessor interfaces, video and image processing, networking and telecommunications, high-speed data acquisition, or any system that needs buffering at very high speeds across different domains. 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 31, 2011 CYF0018V, CYF0036V CYF0072V Logic Block Diagram Document Number: 001-53687 Rev. *H Page 2 of 29 CYF0018V, CYF0036V CYF0072V Contents Pin Definitions ......................................................... 5 Architecture ............................................................. 7 Reset Logic......................................................... 7 Flag Operation.................................................... 7 Full Flag.............................................................. 7 Half-Full Flag ...................................................... 7 Empty Flag ......................................................... 7 Programmable Almost-Empty and Almost-Full Flags................................................ 7 Retransmit from Mark Operation ........................ 7 Flow-through Mailbox Register........................... 7 Selecting Word Sizes ......................................... 8 Power Up.................................................................. 8 Write Mask and Read Skip Operation ................ 8 Programming Flag Offsets and Configuration Registers ...................................... 8 Width Expansion Configuration ........................ 10 Memory Organization for Different Port Sizes .. 11 Read/Write Clock Requirements ...................... 11 JTAG Operation................................................ 12 Document Number: 001-53687 Rev. *H Maximum Ratings ................................................. Operating Range ................................................... Switching Characteristics .................................... Switching Waveforms........................................... Ordering Information ............................................ Ordering Code Definition.................................. Package Diagram .................................................. Acronyms............................................................... Document Conventions........................................ Units of Measure .............................................. Document History Page........................................ Sales, Solutions, and Legal Information............. Worldwide Sales and Design Support.............. Products ........................................................... PSoC Solutions ................................................ 13 13 15 16 24 24 25 26 26 26 27 29 29 29 29 Page 3 of 29 CYF0018V, CYF0036V CYF0072V G Pin Diagram for CYF 0 XXX V Figure 1. 209-Ball FBGA (Top View) 1 2 3 4 5 6 7 8 9 10 11 A FF D0 D1 DNU PORTSZ0 PORTSZ1 DNU DNU RT Q0 Q1 B EF D2 D3 DNU DNU PORTSZ2 DNU DNU REN Q2 Q3 C D4 D5 WEN DNU VCC1 DNU VCC1 DNU RCLK Q4 Q5 D D6 D7 VSS VCC1 DNU LD DNU VCC1 Vss Q6 Q7 E D8 D9 VCC2 VCC2 VCCIO VCCIO VCCIO VCC2 VCC2 Q8 Q9 F D10 D11 VSS VSS VSS DNU VSS VSS VSS Q10 Q11 G D12 D13 VCC2 VCC2 VCCIO VCC1 VCCIO VCC2 VCC2 Q12 Q13 H D14 D15 VSS VSS VSS VCC1 VSS VSS VSS Q14 Q15 J D16 D17 VCC2 VCC2 VCCIO VCC1 VCCIO VCC2 VCC2 Q16 Q17 K DNU DNU WCLK DNU VSS IE VSS DNU VCCIO VCCIO VCCIO L D18 D19 VCC2 VCC2 VCCIO VCC1 VCCIO VCC2 VCC2 Q18 Q19 M D20 D21 VSS VSS VSS VCC1 VSS VSS VSS Q20 Q21 N D22 D23 VCC2 VCC2 VCCIO VCC1 VCCIO VCC2 VCC2 Q22 Q23 P D24 D25 VSS VSS VSS SPI_SEN VSS VSS VSS Q24 Q25 R D26 D27 VCC2 VCC2 VCCIO VCCIO VCCIO VCC2 VCC2 Q26 Q27 T D28 D29 VSS VCC1 VCC1 SPI_SI VCC1 VCC1 VSS Q28 Q29 U DVal DNU D30 D31 PRS DNU SPI_SCLK Vref OE Q30 Q31 V PAF PAE D32 D33 DNU MRS MB DNU MARK Q32 Q33 W TDO HF D34 D35 TDI TRST TMS TCK Vref Q34 Q35 Document Number: 001-53687 Rev. *H Page 4 of 29 CYF0018V, CYF0036V CYF0072V Pin Definitions Pin Name I/O D[35:0] Input Q[35:0] Output Pin Description Data inputs: Data inputs for a 36-bit bus Data outputs: Data outputs for a 36-bit bus WEN Input Write enable: WEN enables WCLK to write data into the FIFO memory and configuration registers. REN Input Read enable: REN enables RCLK to read data from the FIFO memory and configuration registers. IE Input Input enable: IE is the data input enable signal that controls the enabling and disabling of the 36-bit data input pins. If it is enabled, data on the D[35:0] pins is written into the FIFO. The internal write address pointer is always incremented at rising edge of WCLK if WEN is enabled, regardless of the IE level. This is used for 'write masking' or incrementing the write pointer without writing into a location. OE Input Output enable: When OE is LOW, FIFO data outputs are enabled; when OE is HIGH, the FIFO’s outputs are in High Z (high impedance) state. WCLK Input Write clock: When enabled by WEN, the rising edge of WCLK writes data into the FIFO if LD is high and into the configuration registers if LD is low. RCLK Input Read clock: When enabled by REN, the rising edge of RCLK reads data from the FIFO memory if LD is high and from the configuration registers if LD is low. EF Output Empty flag: When EF is LOW, the FIFO is empty. EF is synchronized to RCLK. FF Output Full flag: When FF is LOW, the FIFO is full. FF is synchronized to WCLK. PAE Output Programmable almost-empty: When PAE is LOW, the FIFO is almost empty based on the almost-empty offset value programmed into the FIFO. It is synchronized to RCLK. PAF Output Programmable almost-full: When PAF is LOW, the FIFO is almost full based on the almost-full offset value programmed into the FIFO. It is synchronized to WCLK. LD Input Load: When LD is LOW, D[7:0] (Q[7:0]) are written (read) into (from) the configuration registers. When LD is HIGH, D[35:0] (Q[35:0]) are written (read) into (from) the FIFO RT Input Retransmit: A HIGH pulse on RT resets the internal read pointer to a physical location of the FIFO which is marked by the user (using MARK pin). With every valid read cycle after retransmit, previously accessed data is read and the read pointer is incremented until it is equal to the write pointer. MRS Input Master reset: MRS initializes the internal read and write pointers to zero and sets the output register to all zeroes. During Master Reset, the configuration registers are all set to default values and flags are reset. PRS Input Partial reset: PRS initializes the internal read and write pointers to zero and sets the output register to all zeroes. During Partial Reset, the configuration register settings are all retained and flags are reset. SPI_SCLK Input Serial clock: A rising edge on SPI_SCLK clocks the serial data present on the SPI_SI input into the offset registers if SPI_SEN is enabled. SPI_SI Input Serial input: Serial input data in SPI mode. SPI_SEN Input Serial enable: Enables serial loading of programmable flag offsets and configuration registers. MARK Input Mark for retransmit: When this pin is asserted the current location of the read pointer is marked. Any subsequent retransmit operation resets the read pointer to this position. MB Input Mailbox: When asserted the reads and writes happen to flow-through mailbox register. TCK Input Test clock (TCK) Pin for JTAG TRST Input Reset pin for JTAG TMS Input Test mode select (TMS) pin for JTAG TDI Input Test data in (TDI) pin for JTAG TDO Output Test data out (TDO) for JTAG HF Output Half-full flag: When HF is LOW, half of the FIFO is full. HF is synchronized to WCLK. Document Number: 001-53687 Rev. *H Page 5 of 29 CYF0018V, CYF0036V CYF0072V Pin Definitions (continued) Pin Name DVal PORTSZ [2:0] I/O Output Input Pin Description Data valid: Active low data valid signal to indicate valid data on Q[35:0] Port word size select: Port word width select pins (common for read and write ports) VCC1 Power Supply Core voltage supply 1: 1.8V supply voltage VCC2 Power Supply Core voltage supply 2: 1.5V supply voltage VCCIO Power Supply Supply for I/Os Vref Input Reference voltage: Reference voltage (regardless of I/O standard used) Reference VSS Ground DNU – Ground Do not use: These pins need to be left floating Document Number: 001-53687 Rev. *H Page 6 of 29 CYF0018V, CYF0036V CYF0072V Architecture The CYF0072V, CYF0036V, and CYF0018V are of memory arrays of 72 Mbit, 36 Mbit, and 18 Mbit respectively. The memory organization is user configurable and word sizes can be selected as x9, x12, x16, x18, x20, x24, x32, or x36. The logic blocks to implement FIFO functionality and the associated features are built around these memory arrays. The input and output data buses have a maximium width of 36 bits. The input data bus goes to an input register and the data flow from the input register to the memory is controlled by the write logic block. The inputs to the write logic block are WCLK, WEN and IE. When the writes are enabled through WEN and if the inputs are enabled by IE, then the data on the input bus is written into the memory array at the rising edge of WCLK. This also increments the write pointer. Enabling writes but disabling the data input pins through IE only increments the write pointer without doing any writes or altering the contents of the location. Similarly, the output register is connected to the data output bus. Transfer of contents from the memory to the output register is controlled by the read control logic. The inputs to the read control logic include RCLK, REN, OE, RT and MARK. When reads are enabled by REN and outputs are enabled through OE, the data from the memory pointed by the read pointer is transferred to the output data bus at the rising edge of RCLK along with active low DVal. If the outputs are disabled but the reads enabled, the outputs are in high impedance state, but internally the read pointer is incremented. During write operation, the number of writes performed is always a even number (i.e., minimum write burst length is two and number of writes always a multiple of two). Whereas during read operation, the number of reads performed can be even or odd (i.e., minimum read burst length is one). The MARK signal is used to ‘mark’ the location from which data is retransmitted when requested. Reset Logic The FIFO can be reset in two ways: Master Reset (MRS) and Partial Reset (PRS). The MRS initializes the read and write pointers to zero and sets the output register to all zeroes. It also resets the configuration registers to their default values. The word size is configured through pins; values of the three PORTSZ pins are latched during MRS. A Master Reset is required after power-up before accessing the FIFO. The PRS resets only the read and write pointer to the first location and does not affect the programmed configuration registers. Flag Operation This device provides five flag pins to indicate the condition of the FIFO contents. Full Flag The Full Flag (FF) goes LOW when the device is full. Write operations are inhibited whenever FF is LOW regardless of the state of WEN. FF is synchronized to WCLK, that is, it is exclusively updated by each rising edge of WCLK. The worst case assertion latency for Full Flag is four. As the user cannot know that the FIFO is full for four clock cycles, it is possible that user continues writing data during this time. In this case, the four data word written will be stored to prevent data loss and these words Document Number: 001-53687 Rev. *H have to be read back in order for full flag to get de-asserted.The minimum number of reads required to de-assert full-flag is two and the maximum number of reads required to de-assert full flag is six. Half-Full Flag The Half-Full (HF) flag goes LOW when half of the memory array is written. The assertion of HF is synchronized to WCLK. The assertion and de-assertion of Half-Full flag with associated latencies is explained in Table 12 Empty Flag The Empty Flag (EF) goes LOW when the device is empty. Read operations are inhibited whenever EF is LOW, regardless of the state of REN. EF is synchronized to RCLK, that is, it is exclusively updated by each rising edge of RCLK. The assertion and de-assertion of empty flag with associated latencies is explained in Table 12 Programmable Almost-Empty and Almost-Full Flags The CYF0072V includes programmable Almost-Empty and Almost-Full flags. Each flag is programmed (see Programming Flag Offsets and Configuration Registers on page 8) a specific distance from the corresponding boundary flags (Empty or Full). (offset can range from 16 to 1024) When the FIFO contains the number of words (or fewer) for which the flags are programmed, the PAF or PAE is asserted, signifying that the FIFO is either almost-full or almost-empty. The PAF flag signal transition is caused by the rising edge of the write clock and the PAE flag transition is caused by the rising edge of the read clock. The assertion and de-assertion of empty flag with associated latencies is explained in Table 12 Retransmit from Mark Operation The retransmit feature is useful for transferring packets of data repeatedly. It enables the receipt of data to be acknowledged by the receiver and retransmitted if necessary. The retransmit feature is used when the number of writes after MARK is equal to or less than the depth of the FIFO and at least one word has been read since the last reset cycle. A HIGH pulse on RT resets the internal read pointer to a physical location of the FIFO that is marked by the user (using the MARK pin). With every valid read cycle after retransmit, previously accessed data is read and the read pointer is incremented until it is equal to the write pointer. Flags are governed by the relative locations of the read and write pointers and are updated during a retransmit cycle. Data written to FIFO after activation of RT are also transmitted. The full depth of the FIFO can be repeatedly retransmitted. To mark a location, the Mark pin is asserted when reading that particular location. Flow-through Mailbox Register This feature transfers data from input to output directly by bypassing the FIFO sequence. When MB signal is asserted the data present in D[35:0] will be available at Q[35:0] after two WCLK cycles. Normal read and write operations are not allowed during flow-through mailbox operation. Before starting Flow-through mailbox operation FIFO read should be completed to make data valid DVal high in order to avoid data loss from FIFO. The width of flow-through mailbox register always corresponds to port size. Page 7 of 29 CYF0018V, CYF0036V CYF0072V Selecting Word Sizes The word sizes are configured based on the logic levels on the PORTSZ pins during the master reset (MRS) cycle only (latched on low to high edge). The port size cannot be changed during normal mode of operation and these pins are ignored. Table 1. explains the pins of D[35:0] and Q[35:0] that will have valid data in modes where the word size is less than ×36. If word size is less than ×36, the unused output pins are tri-stated by the device and unused input pins will be ignored by the internal logic. The pins with valid data input D[N:0] and output Q[N:0] is given in Table 1. Data Valid Signal (DVal) Data valid (DVal) is an active low signal, synchronized to RCLK and is provided for easy capture of output data to the user. When a read operation is performed, the DVal signal goes low along with output data. This helps user to capture the data without keeping track of REN to data output latency. This signal also helps when write and read operations are performed continuously at different frequencies by indicating when valid data is available at the output port Q[35:0]. Power Up The device becomes functional after VCC1, VCC2, VCCIO, and Vref attain minimum stable voltage required as given in Recommended DC Operating Conditions on page 13. The device can be accessed tPU time after these supplies attain the minimum required level (see Switching Characteristics on page 15). There is no particular power sequencing required for the device. Table 1. Word Size Selection PORTSZ[2:0] Word Size Active Input Data Pins D[X:0] Active Output Data Pins Q[X:0] 000 ×9 D[8:0] Q[8:0] 001 ×12 D[11:0] Q[11:0] 010 ×16 D[15:0] Q[15:0] 011 ×18 D[17:0] Q[17:0] 100 ×20 D[19:0] Q[19:0] 101 ×24 D[23:0] Q[23:0] 110 ×32 D[31:0] Q[31:0] 111 ×36 D[35:0] Q[35:0] Write Mask and Read Skip Operation As mentioned in Architecture on page 7, enabling writes but disabling the inputs (IE HIGH) increments the write pointer without doing any write operations or altering the contents of the location. This feature is called Write Mask and allows user to move the write pointer without actually writing to the locations. This “write masking” ability is useful in some video applications such as Picture In Picture (PIP). Similarly, during a read operation, if the outputs are disabled by having the OE high, the read data does not appear on the output bus; however, the read pointer is incremented. pin. A low on the SPI_SEN selects the serial method for writing into the registers. For serial programming, there is a separate SCLK and a Serial Input (SI). In parallel mode, a low on the load (LD) pin causes the write and read operation to these registers. The write and read operation happens from the first location (0x1) to the last location (0xA) in a sequence. If LD is high, the writes occur to the FIFO. In addition to loading register values into the FIFO, it is also possible to read the current register values. Register values can be read through the parallel output port regardless of the programming mode selected (serial or parallel). Register values cannot be read serially. The registers may be programmed (and reprogrammed) any time after master reset, regardless of whether serial or parallel programming is selected. Programming Flag Offsets and Configuration Registers See Table 3 on page 9 and Table 4 on page 10 for access to configuration registers in serial and parallel modes. The CYF0072V has ten 8-bit user configurable registers. These registers contain the almost-full offset (M) and almost-empty (N) values which decide when the PAF and PAE flags are asserted. In parallel mode, the read and write operations loop back when the maximum address location of the configuration registers is reached. Simultaneous read and write operations should be avoided on the configuration registers. Any change in configuration registers will take effect after eight write clock cycles(WCLK) cycles. These registers can be programmed into the FIFO in one of two ways: using either the serial or parallel loading method. The loading method is selected using the SPI_SEN (Serial Enable) Document Number: 001-53687 Rev. *H Page 8 of 29 CYF0018V, CYF0036V CYF0072V Table 2. Configuration Registers ADDR Configuration Register Default Bit [7] Bit [6] Bit [5] Bit [4] Bit [3] Bit [2] Bit [1] Bit [0] 0x1 Reserved 0x00 X X X X X X X X 0x2 Reserved 0x00 X X X X X X X X 0x3 Reserved 0x00 X X X X X X X X 0x4 Almost-Empty Flag generation 0x7F address - (LSB) (N) D7 D6 D5 D4 D3 D2 D1 D0 0x5 Almost-Empty Flag generation 0x00 address - (MSB) (N) X X X X X X D9 D8 0x6 Reserved 0x00 X X X X X X X X 0x7 Almost-Full Flag generation address - (LSB) (M) 0x7F D7 D6 D5 D4 D3 D2 D1 D0 0x8 Almost-Full Flag generation address - (MSB) (M) 0x00 X X X X X X D9 D8 0x9 Reserved 0x00 X X X X X X X X 0xA Fast CLK Bit Register 1XXXXXXXb Fast CLK bit X X X X X X X Table 3. Writing and Reading Configuration Registers in Parallel Mode SPI_SEN LD WEN REN WCLK RCLK SPI_SCLK 1 0 0 1 First rising edge because both LD and REN are low X X Parallel write to first register 1 0 0 1 Second rising edge X X Parallel write to second register 1 0 0 1 Third rising edge X X Parallel write to third register 1 0 0 1 Fourth rising edge X X Parallel write to fourth register 1 0 0 1 X X 1 0 0 1 X X 1 0 0 1 X X 1 0 0 1 Tenth rising edge X X Parallel write to tenth register 1 0 0 1 Eleventh rising edge X X Parallel write to first register (roll back) 1 0 1 0 X First rising edge since both LD and REN are low X Parallel read from first register 1 0 1 0 X Second rising edge X Parallel read from second register 1 0 1 0 X Third rising edge X Parallel read from third register 1 0 1 0 X Fourth rising edge X Parallel read from fourth register 1 0 1 0 X X 1 0 1 0 X X 1 0 1 0 X X 1 0 1 0 X Tenth rising edge X Document Number: 001-53687 Rev. *H Operation Parallel read from tenth register Page 9 of 29 CYF0018V, CYF0036V CYF0072V Table 3. Writing and Reading Configuration Registers in Parallel Mode (continued) SPI_SEN LD WEN REN WCLK RCLK SPI_SCLK Operation 1 0 1 0 X Eleventh rising edge X Parallel read from first register (roll back) 1 X 1 1 X X X No operation X 1 0 X Rising edge X X Write to FIFO memory X 1 X 0 X Rising edge X Read from FIFO memory 0 0 X 1 X X X Illegal operation SCLK Table 4. Writing into Configuration Registers in Serial Mode SPI_SEN LD WEN REN WCLK RCLK 0 1 X X X X X 1 0 X X 1 X 0 X 1 0 1 1 X Rising edge X Rising edge X Operation Rising edge Each rising of the SCLK clocks in one bit from the SI (Serial In). Any of the 10 registers can be addressed and written to, following the SPI protocol. X Parallel write to FIFO memory. X Parallel read from FIFO memory. X This corresponds to parallel mode (refer to Table 3). Figure 2. Serial WRITE to Configuration Register Width Expansion Configuration The width of CYFX072V can be expanded to provide word widths greater than 36 bits. During width expansion mode, all control line inputs are common and all flags are available. Empty (Full) flags are created by ANDing the Empty (Full) flags of every FIFO; the PAE and PAF flags can be detected from any one device. This technique avoids reading data from or writing data to the FIFO that is “staggered” by one clock cycle due to the variations in skew between RCLK and WCLK. Figure 3 on page 11 demonstrates an example of 72 bit-word width by using two 36-bit word CYFX072Vs. Document Number: 001-53687 Rev. *H Page 10 of 29 CYF0018V, CYF0036V CYF0072V Figure 3. Using Two CYFX072V for Width Expansion DATAIN (D) 72 36 36 READ CLOCK (RCLK) WRITE CLOCK (WCLK) READ ENABLE (REN) WRITE ENABLE (WEN) OUTPUT ENABLE(OE) PAE PAF CYFX072V CYFX072V HF EF FF FF EF EF 36 FF DATAOUT (Q) 72 36 Memory Organization for Different Port Sizes Read/Write Clock Requirements The 72-Mbit memory has different organization for different port sizes. Table 5 shows the depth of the FIFO for all port sizes. The read and write clocks must satisfy the following requirements: Note that for all port sizes, four to eight locations are not available for writing the data and are used to safeguard against false synchronization of empty and full flags. Table 5. Word Size Selection PORTSZ[2:0] 000 001 010 011 100 101 110 111 Word Size x9 x12 x16 x18 x20 x24 x32 x36 FIFO Depth 8 Meg 4 Meg 4 Meg 4 Meg 2 Meg 2 Meg 2 Meg 2 Meg Memory Size 72 Mbit 48 Mbit 64 Mbit 72 Mbit 40 Mbit 48 Mbit 64 Mbit 72 Mbit ■ Both read (RCLK) and write (WCLK) clocks should be free-running. ■ The clock frequency for both clocks should be between the minimum and maximum range given in Table 10 on page 13. ■ The WCLK to RCLK ratio should be in the range of 0.5 to 2. For proper FIFO operation, the device must determine which of the input clocks – RCLK or WCLK – is faster. This is evaluated by using counters after the MRS cycle. The device uses two 10-bit counters inside (one running on RCLK and other on WCLK), which count 1,024 cycles of read and write clock after MRS. The clock of the counter which reaches its terminal count first is used as master clock inside the FIFO. When there is change in the relative frequency of RCLK and WCLK during normal operation of FIFO, user can specify it by using “Fast CLK bit” in the configuration register (0xA). “1” - indicates freq (WCLK) > freq (RCLK) “0” - indicates freq (WCLK) < freq (RCLK) The result of counter evaluated frequency is available in this register bit. User can override the counter evaluated frequency for faster clock by changing this bit. Whenever there is a change in this bit value, user must wait tPLL time before issuing the next read or write to FIFO. Document Number: 001-53687 Rev. *H Page 11 of 29 CYF0018V, CYF0036V CYF0072V JTAG Operation CYFX072V has two devices connected internally in a JTAG chain as shown in Figure 4 Figure 4. Device Connection in a JTAG Chain TRST TM S TCK TM S TCK device1 TDI TDO TM S TRST TCK device2 TDI TDO TDI TDO Table 6 shows the IR register length and device ID Table 6. JTAG IDCODES IR Register Length 3 8 Device-1 Device-2 Device ID (HEX) “Ignore” 1E3261CF Bypass Register Length 1 1 Table 7. JTAG Instructions for Device-1 Device-1 Opcode (Binary) BYPASS 111 Table 8. JTAG Instructions for Device-2 Device-2 Opcode (HEX) EXTEST 00 HIGHZ 07 SAMPLE/PRELOAD 01 BYPASS FF IDCODE 0F Document Number: 001-53687 Rev. *H Page 12 of 29 CYF0018V, CYF0036V CYF0072V Maximum Ratings Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Storage temperature (without bias) ............ –65 C to +150 C Ambient temperature with power applied –55 C to +125 C Core supply voltage 1 (VCC1) to ground potential.................................................–0.3 V to 2.5 V Core supply voltage 2 (VCC2) to ground potential...............................................–0.3 V to 1.65 V Latch up current .................................................... >100mA I/O port supply voltage (VCCIO) ............................–0.3 V to 3.7 V Voltage applied to I/O pins ...........................–0.3 V to 3.75 V Output current into outputs (LOW) .............................. 20 mA Static discharge voltage........................................... > 2001 V (per MIL–STD–883, Method 3015) Operating Range Range Ambient Temperature –40 C to +85 C Industrial Table 9. Recommended DC Operating Conditions Parameter Description Min Typ Max Unit VCC1 Core supply voltage 1 1.70 1.80 1.90 V VCC2 Core supply voltage 2 1.425 1.5 1.575 V Vref Reference voltage (irrespective of I/O standard used) 0.7 0.75 0.8 V VCCIO I/O supply voltage, read and write LVCMOS33 banks. LVCMOS18 3.00 3.30 3.60 V 1.70 1.8 1.90 V Min Typ Max Unit Table 10. Electrical Characteristics Parameter Icc Description Active current Conditions VCC1=VCC1MAX, – – 300 mA VCC2=VCC2MAX, All I/O switching, 133 MHz) – – 600 mA VCCIO = VCCIOMAX (All outputs disabled) – – 100 mA II Input pin leakage current VIN = VCCIOmax to 0 V –15 – 15 µA IOZ I/O pin leakage current VO = VCCIOmax to 0 V –15 – 15 µA CP Capacitance for TMS and TCK – – – 16 pF CPIO Capacitance for all other – pins except TMS and TCK – – 8 pF Document Number: 001-53687 Rev. *H Page 13 of 29 CYF0018V, CYF0036V CYF0072V Table 11. I/O Characteristics (Over the operating range) I/O standard Nominal I/O supply voltage LVCMOS33 3.3 V LVCMOS18 1.8 V Input Voltage (V) VIL(max) Output voltage (V) VIH(min) VOL(max) 0.80 2.20 30% VCCIO 65% VCCIO Output Current (mA) VOH(min) IOL(max) IOH(max) 0.45 2.40 24 24 0.45 VCCIO – 0.45 16 16 Table 12. Latency Table Latency Parameter Number of cycles Detail LFF_ASSERT Min=0 Max=4 Last data write to FF going low LEF_ASSERT 0 Last data read to EF going low LPRS_TO_ACTIVE 1 PRS to normal operation LMAILBOX 2 Latency from write port to read port when MB = 1 (wrt WCLK) LREN_TO_DATA 4 Latency when REN is asserted low to first data output from FIFO LREN_TO_CONFIG 4 Latency when REN is asserted along with LD to first data read from configuration registers LWEN_TO_PAE_HI 5 Write to PAE going low LWEN_TO_PAF_LO 5 Write to PAF going low LREN_TO_PAE_LO 7 Read to PAE going high LREN_TO_PAF_HI 7 Read to PAF going high LFF_DEASSERT 8 Read to FF going high LRT_TO_REN 9 RT fifth cycle to REN going low for read LRT_TO_DATA Min=19 Max=21 RT fifth cycle to valid data on Q[35:0] LIN Min=25 Max=26 Initial latency for data read after FIFO goes empty during simultaneous read/write LEF_DEASSERT Min=23 Max=24 Write to EF going high Document Number: 001-53687 Rev. *H Page 14 of 29 CYF0018V, CYF0036V CYF0072V Switching Characteristics Parameter Description -133 Min Unit Max tPU Power-up time after all supplies reach minimum value – 2 ms tS Clock cycle frequency 3.3 V LVCMOS 24 133 MHz tS Clock cycle frequency 1.8 V LVCMOS 24 133 MHz tA Data access time 10 ns tCLK Clock cycle time 7.5 41.67 ns tCLKH Clock high time 3.375 – ns tCLKL Clock low time 3.375 – ns tDS Data setup time 3 – ns tDH Data hold time 3 – ns tENS Enable setup time 3 – ns tENH Enable hold time 3 – ns – ns tENS_SI Setup time for SPI_SI and SPI_SEN pins 5 tENH_SI Hold time for SPI_SI and SPI_SEN pins 5 – ns tRATE_SPI Frequency of SCLK – 25 MHz tRS Reset pulse width 100 – ns tPZS Port size select to MRS seup time 25 – ns tPZH MRS to port size select hold time 25 – ns tRSF Reset to flag output time – 50 ns tPRT Retransmit pulse width 5 – RCLK cycles tOLZ Output enable to output in Low Z 4 15 ns tOE Output enable to output valid – 15 ns tOHZ Output enable to output in High Z – 15 ns tWFF Write clock to FF – 8.5 ns tREF Read clock to EF – 8.5 ns tPAF Clock to PAF flag – 17 ns tPAE Clock to PAE flag – 17 ns tHF Clock to HF flag – 17 ns tPLL Time required to synchronize PLL tRATE_JTAG JTAG TCK cycle time – 1024 cycles 100 – tS_JTAG ns Setup time for JTAG TMS,TDI 5 – ns tH_JTAG Hold time for JTAG TMS,TDI 5 – ns tCO_JTAG JTAG TCK low to TDO valid – 10 ns Document Number: 001-53687 Rev. *H Page 15 of 29 CYF0018V, CYF0036V CYF0072V Switching Waveforms Figure 5. Write Cycle Timing tCLKH tCLK tCLKL WCLK tDS tDH D[35:0] tENH tENS WEN, IE NO OPERATION Figure 6. Read Cycle Timing tCLK RCLK tENS tENH REN NO OPERATION LREN_TO_DATA tA Q[35:0] VALID DATA tOLZ tOHZ OE DVal Document Number: 001-53687 Rev. *H Page 16 of 29 CYF0018V, CYF0036V CYF0072V Switching Waveforms (continued) Figure 7. Reset Timing MRS tRS tRSF EF,PAE tRSF FF,PAF, HF tRSF OE=1 Q[35:0] – OE=0 Figure 8. MRS to PORTSZ[2:0] WCLK/RCLK MRS tPZS tPZH PORTSZ[2:0] Document Number: 001-53687 Rev. *H Page 17 of 29 CYF0018V, CYF0036V CYF0072V Switching Waveforms (continued) Figure 9. Empty Flag Timing RCLK tREF EF REN OE Q[35:0] Q(Last)-3 Q(Last)-2 Q(Last)-1 Q(Last) Invalid Data DVal Figure 10. Full Flag Timing WCLK tDS D[35:0] D0 (written) D1 (written) D2 (written) D3 (not written) D4 (not written) tWFF FF WEN Document Number: 001-53687 Rev. *H Page 18 of 29 CYF0018V, CYF0036V CYF0072V Figure 11. Initial Data Latency 1 n 2 WCLK /RCLK D[35:0] D0 D1 D2 D3 D4 Q0 Q1 tA WEN/REN OE Q[35:0] DVal LIN (initial latency) Figure 12. Flow-through Mailbox Operation WCLK D[35:0] REN / WEN 1 DO 2 3 D1 D2 D3 D4 L MAILBOX MB Q[35:0] QO Q1 Q2 Q3 Q4 DVal Document Number: 001-53687 Rev. *H Page 19 of 29 CYF0018V, CYF0036V CYF0072V Figure 13. Configuration Register Write WCLK tENS WEN / IE LD tDS D[35:0] config-reg 0 tDH config-reg 1 config-reg 2 config-reg 4 config-reg 3 config-reg 5 Figure 14. Configuration Register Read WCLK /RCLK REN LREN_TO_CONFIG tA LD Q[35:0] Reg - 1 Figure 15. Empty Flag Deassertion WCLK WEN / IE D[35:0] D0 D1 L EF_DEASSERT EF tREF RCLK REN Document Number: 001-53687 Rev. *H Page 20 of 29 CYF0018V, CYF0036V CYF0072V Figure 16. Empty Flag Assertion 1 RCLK 2 3 4 5 REN tA Q[35:0] Q LAST DVal L REN_TO_DATA EF tREF Figure 17. Full Flag Assertion WCLK WEN / IE D[35:0] D 0 D 1 D x D LAST-1 D LAST NOT WRITTEN NOT WRITTEN FF Figure 18. Full Flag Deassertion WCLK WEN / IE D D[35:0] LAST-5 D LAST-4 D LAST-3 D LAST-2 D LAST-1 D LAST L FF_DEASSERT FF RCLK 1 2 3 7 8 REN Document Number: 001-53687 Rev. *H Page 21 of 29 CYF0018V, CYF0036V CYF0072V Figure 19. PAE Assertion and Deassertion WCLK WEN / IE WEN for OFFSET +1 LOCATION RCLK REN L WEN_TO_PAE_HI 1 READ L REN_TO_PAE_LO PAE tPAE tPAE Figure 20. PAF Assertion and Deassertion WCLK WEN / IE FULL - (OFFSET +1) WRITE RCLK REN L WEN_TO_PAF_LO 1 READ L REN_TO_PAF_HI PAF tPAF tPAF Figure 21. HF Assertion and Deassertion WCLK WEN / IE FULL / 2 WRITE RCLK REN L WEN_TO_PAF_LO 1 READ L REN_TO_PAF_HI HF tHF Document Number: 001-53687 Rev. *H tHF Page 22 of 29 CYF0018V, CYF0036V CYF0072V Figure 22. Mark RCLK tENS REN tENH MARK Q[35:0] Q (N-2) Q (N-1) Q (N) DVal Q (N+1) Q (N+2) Q (N+3) Q (N+4) Q (N+5) Q (N+6) DATA MARKED Figure 23. Retransmit RCLK REN tPRT LRT_TO_REN LRT_TO_DATA RT_FL Q[35:0] Q (N) Q (N+1) RETRANSMIT FROM DATA MARKED DVal Document Number: 001-53687 Rev. *H Page 23 of 29 CYF0018V, CYF0036V CYF0072V Ordering Information Speed (MHz) 133 Ordering Code CYF0018V33L-133BGXI Package Diagram Operating Range Package Type 51-85167 209-ball fine-pitch ball grid array (FPBGA) (14 × 22 × 1.76 mm) Industrial CYF0036V33L-133BGXI CYF0072V33L-133BGXI CYF0018V18L-133BGXI CYF0036V18L-133BGXI CYF0072V18L-133BGXI Ordering Code Definition CY F X XXX VXX X - XXX BGXI Speed: 133 MHz I/O Standard: L = LVCMOS I/O Voltage: 18 = 1.8 V 33 = 3.3 V Density: 018 = 18M 036 = 36M 072 = 72M 0 - single-queue FIFO Cypress Document Number: 001-53687 Rev. *H Page 24 of 29 CYF0018V, CYF0036V CYF0072V Package Diagram Figure 24. 209-Ball FBGA (14 × 22 × 1.76 mm), 51-85167 51-85167 *A Document Number: 001-53687 Rev. *H Page 25 of 29 CYF0018V, CYF0036V CYF0072V Acronyms Document Conventions Acronym Description FF Full flag FIFO First in first out HF Units of Measure Symbol Unit of Measure °C degrees Celsius Half full A microampere HSTL High-speed transceiver logic mA milliampere IE Input enable ms millisecond I/O Input/output MHz megahertz FPBGA fine-pitch ball grid array JTAG Joint test action group LVCMOS Low voltage complementary metal oxide semiconductor MB Mailbox MRS Master reset OE Output enable PAF Programmable almost-full PAE Programmable almost-empty PRS Partial reset RCLK Read clock REN Read enable RCLK Read clock SCLK Serial clock TDI Test data in TDO Test data out TCK Test clock TMS Test mode select WCLK Write clock WEN Write enable Document Number: 001-53687 Rev. *H ns nanosecond ohm pF pico Farad V volt W watt Page 26 of 29 CYF0018V, CYF0036V CYF0072V Document History Page Document Title: CYF0018V/CYF0036V/CYF0072V, 18/36/72 Mbit Programmable FIFOs Document Number: 001-53687 Rev. ECN No. Orig. of Change Submission Date ** 2711566 VKN/PYRS 05/27/09 *A 2725088 NXR 06/26/2009 Included pinout, AC and DC specs, timing diagrams and package diagram *B 2839536 NXR 01/28/2010 Changed Balls B5, D5, F6, K1, K2, K4, K8 and U2 from NC to DNU, Balls C5, C7, G6, H6, J6, L6, M6, N6, T5, T7 FROM NC to VCC1, Balls K9, K10, K11 From NC to VCCIOR Ball W9 from NC to Vref in pin configuration table Swapped Voltage range of VSS1 and VSS2 Updated ICC spec Removed TSKEW parameter Added Ordering Information table Added Part Numbering Nomenclature. Changed title to CYF0018V/CYF0036V/CYF0072V/CYFX144VXXX, 18/36/72 Mbit Programmable FIFOs. Description of Change New data sheet *C 2884377 HKV *D 2963225 AJU/HPV *E 2994379 AJU 07/26/2010 Updated Ordering Information *F 3101023 SIVS 12/03/2010 Added supply-wise current consumption data in Electrical Characteristics. Changed initial latency LIN from 34 to 26 and added initial latency LIN for 110 MHz part in Latency Table. Added 110 MHz part information in JTAG Operation Added details for the 110 MHz part in Switching Characteristics. Added details for the 110 MHz part in Ordering Information. *G 3129722 HKV 01/06/2011 Post to external web. Document Number: 001-53687 Rev. *H 02/25/2010 Post to external web. 06/28/2010 Changed frequency of operation from 250 MHz to 150 MHz Removed Depth Expansion feature and changed associated pin functionality Removed Independent Port size selectability feature Added Data Valid (DVal) signal feature Updated Logic Block Diagram to reflect above changes. Pinout changes: Balls V5, V8, A7, B7, D7, and C6 renamed DNU Ball U1 changed from RXO to DVal Ball V2 changed from WXO/HF to HF Ball A5, A6, B6 changed from WPORTSZ to PORTSZ Ball A9 changed from RT/FL to RT Renamed pwr as POWER, gnd as GND Added Table 3 Table 6 – LD changed to ‘1’ for serial writes Updated Electrical Characteristics and I/O Characteristics Switching Characteristics Table: Renamed tPC as tPU Min frequency changed from 110MH to 24MHz Changed tCLKH and tCLKL to 3.15 ns Changed All setup and hold times to 3 ns Changed tRSF to 50 ns Removed tRSR Changed All clock-to-flag timing to min=8 ns and max=14 ns TPLL changed to 6 ms Changed all OE-related parameters to 15 ns Scaled ICC for reduced frequency Updated all waveforms Added the following tables: Word Size Selection, JTAG Operation, and Latency Table Added Acronyms. Page 27 of 29 CYF0018V, CYF0036V CYF0072V Document Title: CYF0018V/CYF0036V/CYF0072V, 18/36/72 Mbit Programmable FIFOs Document Number: 001-53687 Rev. ECN No. Orig. of Change *H 3197271 SIVS Document Number: 001-53687 Rev. *H Submission Date Description of Change 03/31/2011 Removed 144 Mbit parts from the data sheet Removed multi-queue information from data sheet Removed 2.5 V and 1.5 V options Removed HSTL I/II I/O standard Added clock ratio requirement between RCLK and WCLK Removed redundant Xs from part number to improve readability Removed tie to GND option on DNU pins in pin description Added information on Flag operations to add clarity Added explanation for flow-through mailbox operation Added details on active pins in various port sizes in Table 1. Added Configuration register write to normal operation latency details. Changed configuration register definitions and default values Changed number of unusable locations to four to eight Added JTAG related operation Added latch-up current parameter in maximum operating conditions. Removed 2.5 V and 1.5 V options from DC operating condition table 6. Removed 110 MHz part details and added Cpio parameter in table 7. Removed 2.5 V and 1.5 V options from Table 8. Added latency parameters in Table 9. changed Vol(max) value of LVCMOS33 in table11 Removed 110 MHz part detail from switching characteristics Added timing waveform to improve clarity. Modified ordering information and definition. Page 28 of 29 CYF0018V, CYF0036V CYF0072V Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive psoc.cypress.com/solutions cypress.com/go/clocks PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2009-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-53687 Rev. *H Revised March 31, 2011 All product and company names mentioned in this document are the trademarks of their respective holders. Page 29 of 29