LTC1250 Very Low Noise Zero-Drift Bridge Amplifier U DESCRIPTIO FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ The LTC®1250 is a high performance, very low noise zerodrift operational amplifier. The LTC1250’s combination of low front-end noise and DC precision makes it ideal for use with low impedance bridge transducers. The LTC1250 features typical input noise of 0.75µVP-P from 0.1Hz to 10Hz, and 0.2µVP-P from 0.1Hz to 1Hz. The LTC1250 has DC to 1Hz noise of 0.35µVP-P, surpassing that of low noise bipolar parts including the OP-07, OP-77, and LT1012. The LTC1250 uses the industry-standard single op amp pinout, and requires no external components or nulling signals, allowing it to be a plug-in replacement for bipolar op amps. Very Low Noise: 0.75µVP-P Typ, 0.1Hz to 10Hz DC to 1Hz Noise Lower Than OP-07 Full Output Swing into 1k Load Offset Voltage: 10µV Max Offset Voltage Drift: 50nV/°C Max Common Mode Rejection Ratio: 110dB Min Power Supply Rejection Ratio: 115dB Min No External Components Required Pin Compatible with Standard 8-Pin Op Amps Available in Standard 8-Pin Plastic DIP and 8-Pin SO Packages U APPLICATIO S ■ ■ ■ ■ ■ ■ Electronic Scales Strain Gauge Amplifiers Thermocouple Amplifiers High Resolution Data Acquisition Low Noise Transducers Instrumentation Amplifiers , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 4933642. The LTC1250 incorporates an improved output stage capable of driving 4.3V into a 1k load with a single 5V supply; it will swing ±4.9V into 5k with ±5V supplies. The input common mode range includes ground with single power supply voltages above 12V. Supply current is 3mA with a ±5V supply, and overload recovery times from positive and negative saturation are 0.5ms and 1.5ms, respectively. The internal nulling clock is set at 5kHz for optimum low frequency noise and offset drift; no external connections are necessary. The LTC1250 is available in a standard 8-pin plastic DIP and 8-pin SO packages. U TYPICAL APPLICATIO Differential Bridge Amplifier Input Referred Noise 0.1Hz to 10Hz 2 5V 5V 50Ω GAIN TRIM VS = ±5V AV = 10k 1000pF 0.1µF 1 µV 18.2k 350Ω STRAIN GAUGE 2 1000pF + 0 7 LTC1250 3 –5V – 6 AV = 100 –1 4 18.2k –2 –5V 1250 TA01 0 2 6 4 TIME (s) 8 10 LT1250 TA02 1250fb 1 LTC1250 W W U W ABSOLUTE AXI U RATI GS (Note 1) Total Supply Voltage (V + to V –) ............................. 18V Input Voltage ........................ (V + + 0.3V) to (V – – 0.3V) Output Short Circuit Duration ......................... Indefinite Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec.)................ 300°C Operating Temperature Range LTC1250M (OBSOLETE) ............ – 55°C to 125°C LTC1250C .......................................... 0°C TO 70°C U W U PACKAGE/ORDER I FOR ATIO TOP VIEW NC 1 8 NC –IN 2 7 V+ +IN 3 6 OUT V– 4 5 NC ORDER PART NUMBER ORDER PART NUMBER TOP VIEW LTC1250CN8 N8 PACKAGE 8-LEAD PLASTIC DIP NC 1 8 NC –IN 2 7 V+ +IN 3 6 OUT 5 NC V– TJMAX = 110°C, θJA = 130°CW J8 PACKAGE 8-LEAD CERAMIC DIP TJMAX = 150°C, θJA = 100°CW (J8) 4 LTC1250CS8 S8 PART MARKING S8 PACKAGE 8-LEAD PLASTIC SO LTC1250MJ8 LTC1250CJ8 1250 TJMAX = 110°C, θJA = 200°CW OBSOLETE PACKAGE Consider the N8 or S8 for Alternative Source Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, VIN = ±5V, otherwise specifications are at TA = 25°C. SYMBOL PARAMETER VOS Input Offset Voltage ∆VOS Average Input Offset Drift Long Term Offset Drift Input Noise Voltage (Note 3) en CONDITIONS TA = 25°C (Note 2) (Note 2) in IB Input Noise Current Input Bias Current TA = 25°C, 0.1Hz to 10Hz TA = 25°C, 0.1Hz to 1Hz f = 10Hz TA = 25°C (Note 4) IOS Input Offset Current TA = 25°C (Note 4) CMRR PSRR AVOL Common Mode Rejection Ratio Power Supply Rejection Ratio Large-Signal Voltage Gain Maximum Output Voltage Swing VCM = – 4V to 3V VS = ±2.375V to ±8V RL = 10k, VOUT = ±4V RL = 1k RL = 100k RL = 10k, CL = 50pF ● ● ● SR GBW IS Slew Rate Gain-Bandwidth Product Supply Current LTC1250M TYP MAX ±5 ±10 ±0.01 ±0.05 50 0.75 1.0 0.2 4.0 ±50 ±150 ±950 ±100 ±300 ±500 110 130 115 130 125 170 ±4.0 4.3/–4.7 ±4.92 10 1.5 3.0 4.0 7.0 MIN ● ● ● ● No Load, TA = 25°C ● MIN 110 115 125 ±4.0 LTC1250C TYP MAX ±5 ±10 ±0.01 ±0.05 50 0.75 1.0 0.2 4.0 ±50 ±200 ±450 ±100 ±400 ±500 130 130 170 4.3 /–4.7 ±4.95 10 1.5 3.0 4.0 5.0 UNITS µV µV/°C nV/√Mo µVP-P µVP-P fA/√Hz pA pA pA pA dB dB dB V V V/µs MHz mA mA 1250fb 2 LTC1250 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, VIN = ±5V, otherwise specifications are at TA SYMBOL PARAMETER CONDITIONS fS VOS ∆VOS en Internal Sampling Frequency Input Offset Voltage Average Input Offset Drift Input Noise Voltage (Note 3) IB IOS Input Bias Current Input Offset Current Maximum Output Voltage Swing TA = 25°C TA = 25°C (Note 2) (Note 2) TA = 25°C, 0.1Hz to 10Hz TA = 25°C, 0.1Hz to 1Hz TA = 25°C (Note 4) TA = 25°C (Note 4) RL = 1k RL = 100k TA = 25°C TA = 25°C IS fS Supply Current Sampling Frequency MIN Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: These parameters are guaranteed by design. Thermocouple effects preclude measurement of these voltage levels during automated testing. Note 3: 0.1Hz to 10Hz noise is specified DC coupled in a 10s window; 0.1Hz to 1Hz noise is specified in a 100s window with an RC high-pass LTC1250M TYP MAX 4.75 ±2 ±0.01 1.0 0.3 ±20 ±40 4.3 4.95 1.8 3 ● 4.0 MIN ±5 ±0.05 ±100 ±200 4.0 2.5 LTC1250C TYP MAX 4.75 ±2 ±0.01 1.0 0.3 ±20 ±40 4.3 4.95 1.8 3 ±5 ±0.05 ±100 ±200 2.5 UNITS kHz µV µV/°C µVP-P µVP-P pA pA V V mA kHz filter at 0.1Hz. The LTC1250 is sample tested for noise; for 100% tested parts contact LTC Marketing Dept. Note 4: At T ≤ 0°C these parameters are guaranteed by design and not tested. U W TYPICAL PERFOR A CE CHARACTERISTICS 6 4.0 1.6 1.2 3.0 1.0 0.1Hz TO 10Hz 0.6 0.4 SAMPLING FREQUENCY (kHz) 3.5 SUPPLY CURRENT (mA) 1.4 0.8 TA = 25°C TA = 25°C TA = 25°C INPUT NOISE (µVP-P) Sampling Frequency vs Supply Voltage Supply Current vs Supply Voltage Input Noise vs Supply Voltage 2.5 2.0 1.5 1.0 0.1Hz TO 1Hz 5 4 3 0.5 0.2 2 0 0 4 10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V – (V) 16 1250 G01 4 10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V – (V) 16 1250 G02 4 10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V – (V) 16 1250 G03 1250fb 3 LTC1250 U W TYPICAL PERFOR A CE CHARACTERISTICS Input Noise vs Temperature 8 4.5 1.2 7 SAMPLING FREQUENCY (kHz) 1.0 4.0 SUPPLY CURRENT (mA) 0.8 0.1Hz TO 10Hz 0.6 0.4 0.1Hz TO 1Hz 3.5 3.0 2.5 0.2 50 25 75 0 TEMPERATURE (°C) 100 2.0 –50 –25 125 50 25 0 75 TEMPERATURE (°C) 2 150 1000 VS = ±5V 80 80 GAIN (dB) 40 30 GAIN 40 40 PHASE: RL = 1k 20 VS = ±5V OR SINGLE 5V TA = 25°C CL = 100pF 20 0 10 100 1k FREQUENCY (Hz) 10k 1k 10k 20 100 0 –20 0 60 PHASE: RL = 100k PHASE MARGIN (DEG) 60 50 10 100 1250 G06 100 60 1 75 50 25 TEMPERATURE (°C) 0 Bias Current (Magnitude) vs Temperature 100 VS = ±5V RS = 10Ω 70 0 –50 –25 Gain/Phase vs Frequency 80 10 –50 –20 10M 100k 1M FREQUENCY (Hz) –25 Common Mode Rejection Ratio vs Frequency 140 8 VS = ±5V VCM = 1VRMS 500µs/DIV AV = 100, RL = 100k, CL = 50pF, VS = ±5V 6 120 4 100 2 CMRR (dB) INPUT COMMON MODE RANGE (V) TA = 25°C –5 125 100 1250 G09 Common Mode Input Range vs Supply Voltage Overload Recovery 0 50 75 0 25 TEMPERATURE (°C) 1250 G08 1250 G07 INPUT (V) 3 1250 G05 Voltage Noise vs Frequency OUTPUT (V) 4 125 100 1250 G04 0 5 1 0 –50 –25 0.2 6 BIAS CURRENT (|pA|) INPUT NOISE (µVP-P) VS = ±5V VS = ±5V VS = ±5V VOLTAGE NOISE (nV/√Hz) Sampling Frequency vs Temperature Supply Current vs Temperature 0 –2 80 60 40 –4 20 –6 0 –8 2 3 5 4 6 SUPPLY VOLTAGE (±V) 7 8 1250 G11 1 10 100 1k FREQUENCY (Hz) 10k 100k 1250 G12 1250fb 4 LTC1250 U W TYPICAL PERFOR A CE CHARACTERISTICS Output Swing vs Load Resistance, Dual Supplies Transient Response Output Voltage Swing vs Load Resistance, Single Supply 10 18 RL TO GND 9 14 7 OUTPUT SWING (V) OUTPUT SWING (±V) 2V/DIV 8 6 VS = ±5V 5 4 VS = ±2.5V 3 NEGATIVE SWING POSITIVE SWING 1 AV = 1, RL = 100k, CL = 50pF, VS = ±5V 0 12 VS = 10V 10 8 6 VS = 5V 4 2 1µs/DIV VS = 16V 16 VS = ±8V 0 2 1 3 4 5 6 7 8 LOAD RESISTANCE (kΩ) 0 10 9 V – = GND RL TO GND 2 0 1 2 3 4 5 6 7 8 LOAD RESISTANCE (kΩ) 1250 G14 Output Swing vs Output Current, ±5V Supply 40 VS = SINGLE 5V OUTPUT VOLTAGE (V) 2 1 0 –1 –2 –3 SHORT-CIRCUIT CURRENT (mA) 5 3 OUTPUT VOLTAGE (V) Short-Circuit Current vs Temperature 6 VS = ±5V 10 1250 G15 Output Swing vs Output Current, Single 5V Supply 5 4 9 4 3 2 1 VS = ±15V 30 VOUT = V – 20 10 0 –10 –20 VOUT = V + –30 –4 –5 0.01 0.1 1 OUTPUT CURRENT (mA) 0 0.01 10 0.1 1 OUTPUT CURRENT (mA) –40 –50 –25 10 0 50 25 75 TEMPERATURE (°C) 1250 G17 1250 G16 100 125 1250 G18 TEST CIRCUITS DC to 10Hz Noise Test Circuit (for DC to 1Hz Multiply All Capacitor Values by 10) Offset Test Circuit 100pF 100pF 100k 100k 2 5V 2 10Ω – + 10Ω 7 LTC1250 3 – 7 LTC1250 6 3 OUTPUT 4 –5V 5V 5V + 800k 4 –5V 1250 TC01 2 6 0.02µF 3 – 8 1/2 LT1057 +4 –5V 0.04µF 6 – 1/2 LT1057 1 800k 800k 5 7 OUTPUT + 0.01µF 1250 TC02 1250fb 5 LTC1250 W U U UO APPLICATI S I FOR ATIO Input Noise The LTC1250, like all CMOS amplifiers, exhibits two types of low frequency noise: thermal noise and 1/f noise. The LTC1250 uses several design modifications to minimize these noise sources. Thermal noise is minimized by raising the gM of the front-end transistors by running them at high bias levels and using large transistor geometries. 1/f noise is combated by optimizing the zero-drift nulling loop to run at twice the 1/f corner frequency, allowing it to reduce the inherently high CMOS 1/f noise to near thermal levels at low frequencies. The resultant noise spectrum is quite low at frequencies below the internal 5kHz clock frequency, approaching the best bipolar op amps at 10Hz and surpassing them below 1Hz (Figure 1). All this is accomplished in an industry-standard pinout; the LTC1250 requires no external capacitors, no nulling or clock signals, and conforms to industry-standard 8-pin DIP and 8-pin SO packages. CF ≥ 55pF AV where AV = closed-loop gain. Note that CF is not dependent on the value of RF. Circuits with higher gain (AV > 50) or low loop impedance should not require CF for stability. CF RF RIN CP – LTC1250 + 1250 F02 80 70 OP-27 VOLTAGE NOISE (nV/√Hz) stability with a feedback network impedance as low as 1.9k. This effect can be eliminated by adding a capacitor across the feedback resistor, adding a zero which cancels the input pole (Figure 2). The value of this capacitor should be: OP-07 VS = ±5V RS = 10Ω Figure 2. CF Cancels Phase Shift Due to Parasitic CP 60 50 40 LTC1250 30 20 10 0 0.01 0.1 FREQUENCY (Hz) 1 LTC1250 F01 Figure 1. Voltage Noise vs Frequency Input Capacitance and Compensation The large input transistors create a parasitic 55pF capacitance from each input to V +. This input capacitance will react with the external feedback resistors to form a pole which can affect amplifier stability. In low gain, high impedance configurations, the pole can land below the unity-gain frequency of the feedback network and degrade phase margin, causing ringing, oscillation, and other unpleasantness. This is true of any op amp, however, the 55pF capacitance at the LTC1250’s inputs can affect Larger values of CF, commonly used in band-limited DC circuits, may actually increase low frequency noise. The nulling circuitry in the LTC1250 closes a loop that includes the external feedback network during part of its cycle. This loop must settle to its final value within 150µs or it will not fully cancel the 1/f noise spectrum and the low frequency noise of the part will rise. If the loop is underdamped (large RF, no CF) it will ring for more than 150µs and the noise and offset will suffer. The solution is to add CF as above but beware! Too large a value of CF will overdamp the loop, again preventing it from reaching a final value by the 150µs deadline. This condition doesn’t affect the LTC1250’s offset or output stability, but 1/f noise begins to rise. As a rule of thumb, the RFCF feedback pole should be ≥ 7kHz (1/150µs, the frequency at which the loop settles) for best 1/f performance; values between 100pF and 500pF work well with feedback resistors below 100k. This ensures adequate gain at 7kHz for the LTC1250 to properly null. High value feedback resistors (above 1M) may require experimentation to find the correct value because parasitics, both in the 1250fb 6 LTC1250 W U U UO APPLICATI S I FOR ATIO LTC1250 and on the PC board, play an increasing role. Low value resistors (below 5k) may not require a capacitor at all. Input Bias Current The inputs of the LTC1250, like all zero-drift op amps, draw only small switching spikes of AC bias current; DC leakage current is negligible except at very high temperatures. The large front-end transistors cause switching spikes 3 to 4 times greater than standard zero-drift op amps: the ±50pA bias current spec is still many times better than most bipolar parts. The spikes don’t match from one input pin to the other, and are sometimes (but not always) of opposite polarity. As a result, matching the impedances at the inputs (Figure 3) will not cancel the bias current, and may cause additional errors. Don’t do it. RF RIN – LTC1250 + 1250 F03 Figure 3. Extra Resistor Will Not Cancel Bias Current Errors Output Drive The LTC1250 includes an enhanced output stage which provides nearly symmetrical output source/sink currents. This output is capable of swinging a minimum of ±4V into a 1k load with ±5V supplies, and can sink or source >20mA into low impedance loads. Lightly loaded (RL ≥100k), the LTC1250 will swing to within millivolts of either rail. In single supply applications, it will typically swing 4.3V into a 1k load with a 5V supply. when the LTC1250’s output is heavily loaded, the chip may dissipate substantial power, raising the temperature of the package and aggravating thermocouples at the inputs. Although the LTC1250 will maintain its specified accuracy under these conditions, care must be taken in the layout to prevent or compensate circuit errors. Be especially careful of air currents when measuring low frequency noise; nearby moving objects (like people) can create very large noise peaks with an unshielded circuit board. For more detailed explanations and advice on how to avoid these errors, see the LTC1051/LTC1053 data sheet. Sampling Behavior The LTC1250’s zero-drift nulling loop samples the input at ≈ 5kHz, allowing it to process signals below 2kHz with no aliasing. Signals above this frequency may show aliasing behavior, although wideband internal circuitry generally keeps errors to a minimum. The output of the LTC1250 will have small spikes at the clock frequency and its harmonics; these will vary in amplitude with different feedback configurations. Low frequency or band-limited systems should not be affected, but systems with higher bandwidth (oversampling A/Ds, for example) may need to filter out these clock artifacts. Output spikes can be minimized with a large feedback capacitor, but this will adversely affect noise performance (see Input Capacitance and Compensation on the previous page). Applications which require spike-free output in addition to minimum noise will need a low-pass filter after the LTC1250; a simple RC will usually do the job (Figure 4). The LTC1051/LTC1053 data sheet includes more information about zero-drift amplifier sampling behavior. CF RF Minimizing External Errors The input noise, offset voltage, and bias current specs for the LTC1250 are all well below the levels of circuit board parasitics. Thermocouples between the copper pins of the LTC1250 and the tin/lead solder used to connect them can overwhelm the offset voltage of the LTC1250, especially if a soldering iron has been around recently. Note also that – 47k LTC1250 + 0.01 1250 F04 Figure 4. RC Output Pole Limits Bandwidth to 330Hz 1250fb 7 LTC1250 U W U UO APPLICATI S I FOR ATIO Single Supply Operation The LTC1250 will operate with single supply voltages as low as 4.5V, and the output swings to within millivolts of either supply when lightly loaded. The input stage will common mode to within 250mV of ground with a single 5V supply, and will common mode to ground with single supplies above 11V. Most bridge transducers bias their inputs above ground when powered from single supplies, allowing them to interface directly to the LTC1250 in single supply applications. Single-ended, ground-referenced signals will need to be level shifted slightly to interface to the LTC1250’s inputs. Fault Conditions ally severe fault conditions can destroy the part. All pins are protected against faults of ±25mA or 5V beyond either supply, whichever comes first. If the external circuitry can exceed these limits, series resistors or voltage clamp diodes should be included to prevent damage. The LTC1250 includes internal protection against ESD damage. All data sheet parameters are maintained to 1kV ESD on any pin; beyond 1kV, the input bias and offset currents will increase, but the remaining specs are unaffected and the part remains functional to 5kV at the input pins and 8kV at the output pin. Extreme ESD conditions should be guarded against by using standard antistatic precautions. The LTC1250 is designed to withstand most external fault conditions without latch-up or damage. However, unusu- 1250fb 8 LTC1250 U PACKAGE DESCRIPTIO J8 Package 8-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) CORNER LEADS OPTION (4 PLCS) 0.023 – 0.045 (0.584 – 1.143) HALF LEAD OPTION 0.045 – 0.068 (1.143 – 1.727) FULL LEAD OPTION 0.005 (0.127) MIN 0.405 (10.287) MAX 8 7 6 5 0.025 (0.635) RAD TYP 0.220 – 0.310 (5.588 – 7.874) 1 0.300 BSC (0.762 BSC) 2 3 4 0.200 (5.080) MAX 0.015 – 0.060 (0.381 – 1.524) 0.008 – 0.018 (0.203 – 0.457) 0.385 ± 0.025 (9.779 ± 0.635) 0° – 15° 0.045 – 0.068 (1.143 – 1.727) 0.014 – 0.026 (0.360 – 0.660) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS. 0.125 3.175 0.100 ± 0.010 MIN (2.540 ± 0.254) J8 0694 OBSOLETE PACKAGE 1250fb 9 LTC1250 U PACKAGE DESCRIPTIO N8 Package 8-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) .400* (10.160) MAX 8 7 6 5 1 2 3 4 .255 ± .015* (6.477 ± 0.381) .300 – .325 (7.620 – 8.255) .008 – .015 (0.203 – 0.381) +.035 .325 –.015 ( 8.255 +0.889 –0.381 ) .045 – .065 (1.143 – 1.651) .130 ± .005 (3.302 ± 0.127) .065 (1.651) TYP .100 (2.54) BSC .120 (3.048) .020 MIN (0.508) MIN .018 ± .003 (0.457 ± 0.076) N8 1002 NOTE: 1. DIMENSIONS ARE INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) 1250fb 10 LTC1250 U PACKAGE DESCRIPTIO S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) .189 – .197 (4.801 – 5.004) NOTE 3 .045 ±.005 .050 BSC 8 .245 MIN 7 6 5 .160 ±.005 .150 – .157 (3.810 – 3.988) NOTE 3 .228 – .244 (5.791 – 6.197) .030 ±.005 TYP 1 RECOMMENDED SOLDER PAD LAYOUT .010 – .020 × 45° (0.254 – 0.508) .008 – .010 (0.203 – 0.254) .053 – .069 (1.346 – 1.752) 0°– 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. DIMENSIONS IN .014 – .019 (0.355 – 0.483) TYP INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) 2 3 4 .004 – .010 (0.101 – 0.254) .050 (1.270) BSC SO8 0303 1250fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC1250 UO TYPICAL APPLICATI S Differential Thermocouple Amplifier Reference Buffer 15V 7.5k 3 3 1 7 + LTC1250 2 LM399 – R1 10k 0.1% 6 5V 2 7 – LTC1250 4 3 4 R3 1M 0.1% C1 100pF – 2 + R2 10k 0.1% TYPE K † 1250 TA03 C2 100pF 5V 10mV/°C VOUT LT1025 GND R7 500Ω FULL-SCALE TRIM R8 5k 1% R5 3k VIN VOUT 100mV/°C R6 7.5k 1% 4 –5V R4 1M 0.1% VCM ±10ppm ERROR AT ±15mA 1µVP-P OUTPUT NOISE 2.5µV/°C DRIFT (DUE TO LM399) + 6 R9 33k † FOR BEST ACCURACY, THERMOCOUPLE RESISTANCE SHOULD BE LESS THAN 100Ω –5V 1250 TA04 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1050/LTC1051/ LTC1053 Single/Dual/Quad Precision Zero-Drift Op Amp VOS Max = 5µV, VSUPPLY Max = 16.5V LTC1150/LTC1151 Single/Dual ±15V Zero-Drift Op Amp High Voltage Operation LTC2050/LTC2051/ LTC2052 Single/Dual/Quad Zero-Drift Op Amp Single Supply 2.7V to =/–5V, SOT-23/MS8/GN16 Package LTC2053 Zero-Drift Instrumentation Amp Rail-Rail, MS8, 116dB, Two Resistors Set Gain LTC2054/LTC2055 Single/Dual Zero-Drift Op Amp 150µA per Amplifier (Max), SOT-23/MS8 Package LTC6800 Rail-to-Rail Input/Output Instrumentation Amp Low Cost, Single Supply, MS8, Two Resistors Set Gain 1250fb 12 Linear Technology Corporation LT/GP 0205 1K REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 1994