CY2DL818 1:8 Clock Fanout Buffer Features Low voltage operation VDD = 3.3V 1:8 fanout Single-input-configurable for LVDS, LVPECL, or LVTTL 8 pair of LVDS Outputs Drives either a 50-ohm or 100-ohm load (selectable) Low input capacitance Low output skew Low propagation delay Typical (tpd < 4 ns) Packages available include: TSSOP Does not exceed Bellcore 802.3 standards Operation at => 350 MHz – 700 Mbps This Cypress series of network circuits is produced using advanced 0.35-micron CMOS technology, achieving the industry’s fastest logic. The Cypress CY2DL818 fanout buffer features a single LVDS or a single-ended LVTTL-compatible input and eight LVDS output pairs. Designed for data communications clock management applications, the large fanout from a single input reduces loading on the input clock. The Cypress CY2DL818 is ideal for both level translations from single-ended to LVDS and/or for the distribution of LVDS-based clock signals. The Cypress CY2DL818 has configurable input and output functions. The input can be selectable for LVCMOS/LVTTL, LVPECL, or LVDS signals, while the output drivers support standard and high-drive LVDS. Drive either a 50-ohm or 100-ohm line with a single part number/device. Pin Configuration Block Diagram 37 36 Q1A Q1B 35 34 INPUT Q2A Q2B 33 32 Q3A Q3B (LVPECL / LVDS / LVTTL) 10 INPUT A INPUT B 31 30 Q4A 6 28 27 Q5A VDD GND INPUT A INPUT B GND VDD VDD VDD VDD VDD GND GND Q4B 11 InConfig GND VDD VDD VDD VDD InConfig CNTRL Q5B 26 Q6A Q6B 25 24 Q7A Q7B 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 CY2DL 818 • • • • • • • • • • • • • Description 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 GND Q1A Q1B Q2A Q2B Q3A Q3B Q4A Q4B VDD Q5A Q5B Q6A Q6B Q7A Q7B Q8A Q8B GND 38 pin TSSOP 22 Q8A Q8B 21 CNTRL 7 OUTPUT (LVDS) Cypress Semiconductor Corporation Document #: 38-07058 Rev. *B • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Revised December 15, 2002 CY2DL818 Pin Description Pin Number 1, 9,12, 18,19,20,38 2,3,4,5,8, 13 14,15,16,17,29 10,11 Pin Name GND Pin Standard Interface POWER Ground 37, 36,35,34, 33,32,31, 30, 28,27,26,25, 24,23,22,21 6 Q1A, Q1B, Q2A, Q2B, Q3A, Q3B, Q4A, Q4B, Q5A, Q5B, Q6A, Q6B, Q7A, Q7B, Q8A, Q8B InConfig 7 CNTRL Pin Description VDD POWER Input A, Input B(#) Default: LVPECL / LDVS Differential input pair or single line. Optional: LVTTL/LVCMOS LVPECL/LVDS default. See InConfig below. single pin. LDVS Differential Outputs Power Supply LVTTL / LVCMOS LVTTL / LVCMOS Converts inputs from the default LVPECL/LVDS (logic = 0) To LVTTL/LVCMOS (logic = 1) “default pull-up” See Figure 5 and Figure 6 for additional information Converts into a high-speed driver. Logic = 0 = 100 ohm Logic = 1 = 50-ohm “default pull-up” See Figure 7 for additional Information Output Drive Control for Standard and Bus/B/Hi-Drive CNTRL Pin 7 Binary Value 0 Drive STD Standard 1 Hi-drive/Bus/B Impedance 100 Ohms 50 Ohms 100 Ohms 50 Ohms Output Voltage Value VO = Voutput V = 1/2 * VO V = 2 * VO V = VO Input Receiver Configuration for Differential or LVTTL/LVCMOS InCONFIG Pin 6 Binary Value 1 0 Input Receiver Family LVTTL in LVCMOS LVDS LVPECL Input Receiver Type Single-ended non-inverting, inverting, void of bias resistors. Low-voltage differential signaling Low-voltage pseudo (positive) emitter coupled logic Function Control of the TTL Input Logic Used to Accept or Invert the Input Signal Ground VCC Ground VCC Input Condition Input B (–) Pin 11 Input A (+) Pin 10 Input B (–) Pin 11 Input A (+) Pin 10 Input A (+) Pin 10 Input B (–) Pin 11 Input A (+) Pin 10 Input B (–) Pin 11 LVTTL/LVCMOS INPUT LOGIC Input Logic Input Input – Bar Input Input – Bar Input Input – Bar Input Input – Bar Output Logic Q Pins, Q1A or Q1 Input Input – Bar Input – Bar Input Input Input – Bar Input – Bar Input Power Supply Characteristics Parameter ICCD IC Description Test Conditions Dynamic Power Supply Current VDD = Max Input toggling 50% Duty Cycle, Outputs Open Total Power Supply Current VDD = Max Input toggling 50% Duty Cycle, Outputs Open fL = 100 MHz Document #: 38-07058 Rev. *B Min. Typ. Max. Unit 0.40 0.5 mA/MHz 40 80 mA Page 2 of 8 CY2DL818 Maximum Ratings[1][2] Supply Voltage to Ground Potential (Outputs only) ........................................ –0.3V to VDD + 0.3V Storage Temperature: ................................–65°C to + 150°C DC Input Voltage ................................... –0.3V to VDD + 0.3V Ambient Temperature:................................... –40°C to +85°C DC Output Voltage................................. –0.3V to VDD + 0.9V Supply Voltage to Ground Potential Power Dissipation........................................................ 0.75W (Inputs and VCC only)....................................... –0.3V to 4.6V DC Electrical Characteristics: 3.3V–LVDS Input Parameter VID Description Conditions Min. Magnitude of Differential Input Voltage Typ. Max. Unit 100 600 VIC Common-mode of Differential Input VoltageIVIDI (min. and max.) VIH Input High Voltage VIL Input Low Voltage Guaranteed Logic Low Level IIH Input High Current VDD = Max VIN = VDD ±10 IIL Input Low Current VDD = Max VIN = VSS ±10 II Input High Current VDD = Max, VIN = VDD(max.) Guaranteed Logic High Level IVIDI/2 2.4 – (IVIDI/2) InConfig/Cntrl Pins 2 mV V V 0.8 V ±20 µA ±20 µA ±20 µA DC Electrical Characteristics: 3.3V–LVPECL Input Parameter Description Conditions Min. Guaranteed Logic High Level Typ. Max. Unit 400 2400 mV 1.65 2.25 V I VID I Differential input voltage p-p VCM Common-Mode Voltage IIH Input High Current VDD = Max VIN = VDD ±10 ±20 µA IIL Input Low Current VDD = Max VIN = VSS ±10 ±20 µA Typ. Max. Unit DC Electrical Characteristics: 3.3V–LVTTL/LVCMOS Input Parameter VIH VIL IIH IIL II VIK VH Description Input High Voltage Conditions Min. Guaranteed Logic High Level 2 V Input Low Voltage Guaranteed Logic Low Level 0.8 V Input High Current VDD = Max VIN = 2.7V 1 µA Input Low Current VDD = Max VIN = 0.5V –1 µA Input High Current VDD = Max., VIN = VDD(Max) 20 µA Clamp Diode Voltage VDD = Min., IIN = -18mA –0.7 Input Hysteresis –1.2 80 V mV DC Electrical Characteristics: 3.3V–LVDS OUTPUT Parameter Description Conditions I VOD I Differential Output Voltage p-p VDD = 3.3V, VIN = VIH or VIL Risetime Pin Control (pin 7) logic is “FALSE” defaulting to 100-ohm output DIfferential 20% to 80% CL – 10 pF RL and CL to GND CL = Cintrinsic and Cexternal See Figure 3 Falltime Pin Control (pin 7) logic is “TRUE” setting 50-ohm output drivers differential 20% to 80% CL – 10 pF RL and CL to GND CL = Cintrinsic and Cexternal See Figure 3 IOS Output Short Circuit DOUT = 0V or DOUT- = 0V VOH Output Voltage high VOL Output Voltage low Falltime Risetime Min. RL = 100 ohm Max. Unit 0.55 V 800 1500 ps 800 1500 ps 350 600 ps 350 600 ps –10 mA 1550 mV 0.25 RL = 50 ohm RL = 100 ohm Typ. 925 mV Notes: 1. Stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. This is intended to be a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. Document #: 38-07058 Rev. *B Page 3 of 8 CY2DL818 AC Switching Characteristics @ 3.3 V VDD = 3.3V ±5%, Temperature = –40°C to +85°C Parameter Description Conditions Min. Typ Max Unit tPLH Propagation Delay – Low to High 4.5 ns tPHL Propagation Delay – High to Low 4.5 ns tSK(0) Output Skew: Skew between outputs of the same package (in phase) tSK(p) Pulse Skew: Skew between opposite transitions of the same output (tPHL – tPLH) tSK(t) Package Skew: Skew between outputs of different packages at the same power supply voltage, temperature and package type. 200 200 ps ps 1.6 ns High Frequency Parametrics Parameter Description Conditions Fmax Maximum frequency VDD = 3.3V 50% duty cycle tW(50-50) Standard Load Circuit. LVDS VID = 100 mV Dj Deterministic Jitter 50% duty cycle tW(50-50) Standard Load Circuit. LVDS VID = 100 mV Min. Typ 50 Max Unit 400 MHz ps Idd @ 25°C Idd (mA) vs. Input Freq. (MHz) 200 180 160 Idd (mA) 140 High or B Drive Curves 120 100 80 60 Standard Drive Curves 40 20 0 40 140 240 LD 3.3 LD 3.465 340 440 540 Input Freq. (MHz) LD 3.135 HD 3.135 HD 3.3 HD 3.465 Figure 1. IDD Current vs. Frequency in Low Drive and High Drive Full Load Document #: 38-07058 Rev. *B Page 4 of 8 CY2DL818 A TPA Pulse 50 10pF Generator TPC B 50 TPB Standard Termination V1A 1.4 V 0V Differential V1B 1.0 V V0Y 1.4 V 0V Differential 1.0 V V0Z T PLH TPHL 80% 0V Differential V0Y - V0Z 20% tR tF Figure 2. Differential Receiver to Driver Propagation Delay and Driver Transition Time[3,4,5,6] A TPA 50 P u ls e G e n e r a to r TP C B 50 TP B VOC S t a n d a r d T e r m in a t io n V I( A ) 1 .4 0 V V I( B ) 1 .0 V VOD N e x t D e v ic e V o c (p p ) VDD V o c (s s ) Figure 3. Test Circuit and Voltage Definitions for the Driver Common-Mode Output Voltage[3,4,5,6,7] Notes: 3. All input pulses are supplied by a frequency generator with the following characteristics: TR and tF ≤ 1 ns; pulse rate = 50 Mpps; pulse width = 10 ± 0.2 ns. 4. RL = 50 ohm/100 ohm ± 1%. 5. CL includes instrumentation and fixture capacitance within 6 mm of the DUT. 6. TPA and B are used for prop delay and Rise/Fall Measurements. TPC is used for VOC measurements only. 7. All outputs should be loaded, used or not, in order to minimize noise and currents. Document #: 38-07058 Rev. *B Page 5 of 8 CY2DL818 A TPA Pulse Generator 50 10pF TPC B 50 TPB Standard Termination VI(A) 1.4V VI(B) 1.0V 100% 80% 0.0V 20% 0% tF tR Figure 4. Test Circuit and Voltage Definitions for the Differential Output Signal [3,4,5,6] INPUT A LVCMOS / LVTTL INPUT B GND InConfig 1 LVTTL/LVCMOS Figure 5. InConfig Control for LVCMOS Input[8] LVPECL & LVDS In C o n fig 0 L V D S /L V P E C L Figure 6. InConfig Control for Differential Input[9] 0 CNTRL 1 100 50 100 H i D r iv e B 50 S ta n d a rd O hm s Ohm s O hm s Ohm s ’V o = V o ’V o = 1 /2 V o ’V o = 2 V o ’V o = V o Figure 7. CNTRL Control for Standard or High-drive Drivers[10] Notes: 8. See Function Control of the TTL Input Logic Used to Accept or Invert the Input Signal on page 2. 9. LVPECL or LVDS differential input value. 10. Standard 100-ohm output impedance: high-drive 50-ohm output impedance. Document #: 38-07058 Rev. *B Page 6 of 8 CY2DL818 Ordering Information Part Number Package Type Product Flow CY2DL818ZI 38-pin TSSOP Industrial, –40° to 85°C CY2DL818ZIT 38-pin TSSOP–Tape and Reel Industrial, –40° to 85°C CY2DL818ZC 38-pin TSSOP Commercial, 0° to 70°C CY2DL818ZCT 38-pin TSSOP–Tape and Reel Commercial, 0° to 70°C Package Drawing and Dimensions 38-pin TSSOP (4.40 mm body) Z38 51-85151-** All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-07058 Rev. *B Page 7 of 8 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY2DL818 Document Title: CY2DL818 1:8 Clock Fanout Buffer Document Number: 38-07058 Rev. ECN No. Issue Date Orig. of Change Description of Change ** 115151 05/30/02 EHX New Data Sheet *A 117611 09/16/02 RGL Changed the figure cross reference in page 2 and added a note 6 in page 5 *B 122745 12/15/02 RBI Added power-up requirements to maximum ratings information. Document #: 38-07058 Rev. *B Page 8 of 8